Copper(II)‐Specific Fluorogenic Task‐Specific Ionic Liquids as Selective Fluorescence Probes and Recyclable Extractants

The designed synthesis of a series of copper(II) specific fluorogenic hydrophobic task‐specific ionic liquids (TSILs) from a new naphthalene‐based tetradentate ligand is reported. Absorption and fluorescence spectral studies reveal both the ligand and its derivative TSILs show exclusive selectivity towards copper(II) ions. The Stern–Volmer method for calculation of the detection limit for ligand and TSIL_1–3 shows values of 0.12, 20, 17, and 15 μM , respectively. Extraction and striping studies by doping these TSILs in [bmim][NTf₂] demonstrated that these TSILs are recyclable extractants for the selective recovery of Cu^II ions from a mixture of 14 relevant metal chloride aqueous solutions in biphasic liquid–liquid extraction with approximately 95 % recovery.     

Bicyclic imidazolium-based ionic liquids: synthesis and characterization

We previously reported the use of imidazole as starting compound for preparing a bicyclic imidazolium ionic liquid, [b-3C-im][NTf₂], with an overall 29% isolated yield in four synthetic steps. This new room temperature ionic liquid was shown to be far more chemically stable than commonly used [bmim][PF₆], [bdmim][PF₆], and [bdmim][NTf₂]. Because of this intriguing chemical stability, it prompted us to develop a more generalized and high yielding synthesis so that molecular diversity of bicyclic ionic liquids may be explored. In this work, we amended the previous synthetic route by employing 4-chlorobutyronitrile or 5-chlorovaleronitrile as starting materials and successfully developed a five-step synthesis of a series of novel bicyclic imidazolium-based ionic liquids in 40-53% overall isolated yields. We investigated intrinsic reactivity of all bicyclic ionic liquids prepared and found that, under strongly basic conditions, among all tested ionic liquids the 5,5-membered [R-3C-im][NTf₂] ionic liquids were most stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] ionic liquid was 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. Under identical condition, the commonly used [bmim][NTf₂] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases, only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and all other ionic liquids gave no detectable exchanges even after 25 days at ambient temperature. Moreover, both [bmim][NTf₂] and [bdmim][NTf₂] ionic liquids were readily methylated at C-2 position with methyl iodide under basic condition at room temperature. Under the same condition, [R-3C-im][NTf₂] and [R-4C-im][NTf₂] ionic liquids were completely stable and chemically inert. We envisioned that [R-3C-im][NTf₂] should be well suited as solvents for organic synthesis.     

Speciation of Rare‐Earth Metal Complexes in Ionic Liquids: A Multiple‐Technique Approach

The dissolution process of metal complexes in ionic liquids was investigated by a multiple‐technique approach to reveal the solvate species of the metal in solution. The task‐specific ionic liquid betainium bis(trifluoromethylsulfonyl)imide ([Hbet][Tf₂N]) is able to dissolve stoichiometric amounts of the oxides of the rare‐earth elements. The crystal structures of the compounds [Eu₂(bet)₈(H₂O)₄][Tf₂N]₆, [Eu₂(bet)₈(H₂O)₂][Tf₂N]₆?2H₂O, and [Y₂(bet)₆(H₂O)₄][Tf₂N]₆ were found to consist of dimers. These rare‐earth complexes are well soluble in the ionic liquids [Hbet][Tf₂N] and [C₄mim][Tf₂N] (C₄mim=1‐butyl‐3‐methylimidazolium). The speciation of the metal complexes after dissolution in these ionic liquids was investigated by luminescence spectroscopy, ¹H, ¹³C, and ⁸⁹Y NMR spectroscopy, and by the synchrotron techniques EXAFS (extended X‐ray absorption fine structure) and HEXS (high‐energy X‐ray scattering). The combination of these complementary analytical techniques reveals that the cationic dimers decompose into monomers after dissolution of the complexes in the ionic liquids. Deeper insight into the solution processes of metal compounds is desirable for applications of ionic liquids in the field of electrochemistry, catalysis, and materials chemistry.     

Extraction of Metal Ions from Aqueous Solutions Using Imidazolium Based Ionic Liquids

This article represents a step towards how to choose an ionic liquid as the solvent to improve metal ion (Ag⁺ and Pb²⁺) extraction. The liquid-liquid solvent extraction is proposed with the following imidazolium ionic liquids (ILs): 1-ethyl-3-ethylimidazolium, or 1-butyl-3-ethylimidazolium, or 1-hexyl-3-ethylimidazolium bis{(trifluoromethyl)sylfonyl}imide [EEIM][NTf₂], or [BEIM][NTf₂], or [HEIM][NTf₂], or 1-butyl-3-ethylimidazolium hexafluorophosphate [BEIM][PF₆], or 1-hexyl-3-ethylimidazolium hexafluorophosphate [HEIM][PF₆] and the popular 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF₆] for comparison. The effect of anion type (NTf₂⁻ versus PF₆⁻) and the effect of structural components of an ionic liquid including alkyl chain length at the cation and the ethyl substituent instead methyl at the cation, on the extraction and re-extraction processes by using dithizone as a metal chelator, were studied at 296 K. Dithizone was employed to form neutral metal-dithizone complexes with heavy metal ions to extract them from aqueous solution into the ILs. Electronic Supplementary Material  The online version of this article () contains supplementary material, which is available to authorized users. Presented at the 236th ACS National Meeting, August 17–21, Philadelphia, USA.     

1-Butyl-2,3-trimethyleneimidazolium bis(trifluoromethylsulfonyl)imide ([b-3C-im][NTf2]): a new, stable ionic liquid

Using imidazole as the starting material, the synthesis of a new bicyclic ionic liquid [b-3C-im][NTf₂] is described. Except for the alkylation reaction in the second step (40% yield) of this four-step synthesis of [b-3C-im][NTf₂], others were all high yielding reactions (85-94% isolated yields). We investigated intrinsic reactivity of this and other imidazolium-based ionic liquids and found that, under strongly basic conditions (KOD in CD₃OD/D₂O (1:1) solution), the new ionic liquid was stable to solvent deuterium isotope exchange while the previously reported [bdmim][NTf₂] and [bdmim][PF₆] ionic liquids were 50% deuterium exchanged at its C-2 methyl in 30 min at ambient temperature. At the same experimental condition, the most commonly employed [bmim][PF₆] ionic liquid was deuterium exchanged instantaneously at its C-2 hydrogen. In the absence of bases (CD₃OD/D₂O = 1:1), only [bmim][PF₆] was deuterium exchanged (50% within 1 h) and other ionic liquids gave no detectable exchanges even after one week at ambient temperature. It is therefore concluded that the new [b-3C-im][NTf₂] ionic liquid is far more chemically stable than previously reported [bmim][PF₆], [bdmim][NTf₂], and [bdmim][PF₆].     

Amine basicity: measurements of ion pair stability in ionic liquid media

The stability constants relevant to the formation of amine/p-nitrophenol ion pairs have been determined in [bmim][BF₄] solution, in the presence of butylamine, piperidine, and triethylamine, by using spectrophotometric measurements. In order to evaluate how the ion pair stability is affected by ionic liquid structure, piperidine has been chosen as model amine for studies in [bmim][PF₆], [bmim][NTf₂], [bm₂im][NTf₂] and in several [bmim][BF₄]/1,4-dioxane binary mixtures. Data obtained in ionic liquid solutions have been compared with those previously reported in conventional organic solvents.     

High temperature and highly selective stationary phases of ionic liquid bonded polysiloxanes for gas chromatography

Due to the special performance of “dual nature” and synthetic flexibility, ionic liquids (ILs) have been an attractive research subject of stationary phases for gas chromatography (GC). In this work, a novel ionic liquid (IL) bonded polysiloxane ([PSOMIM][NTf₂]) with anion of bis-trifluoromethanesulfonylimide (NTf₂⁻) was synthesized, and another one with chloride anion ([PSOMIM][Cl]) was also prepared for the purpose of comparison. The thermo-stability of the product was evaluated by thermogravimetric (TG) test and the result indicated that [PSOMIM][NTf₂] did not decompose slightly until 380 °C. Then the solvation behaviors of the ILs were characterized using solvation parameter model. Subsequently, [PSOMIM][NTf₂] and [PSOMIM][Cl] were used as stationary phases to prepare capillary columns for GC, respectively. The column efficiency of [PSOMIM][NTf₂] column was 4776 plates/m (k = 3.64 ± 0.08, naphthalene), and that of the other one was 3170 plates/m (k = 2.84 ± 0.11, naphthalene). The selectivity of the novel stationary phases for analytes, including Grob reagent, aromatic positional isomers was further evaluated. Furthermore, the chromatograms of n-alkanes and polycyclic aromatic hydrocarbons (PAHs) on [PSOMIM][NTf₂] column were compared with that on [PSOMIM][Cl] column. [PSOMIM][NTf₂] stationary phase also exerted good selectivity for fatty acid methyl esters (FAMEs), polychlorinated biphenyls (PCBs) and aromatic amines.     

Studies on Liquid/liquid Extraction of Copper Ion with Room Temperature Ionic Liquid

Room temperature ionic liquids are regarded as “Green solvents” for their nonvolatile and thermally stable properties. They are employed to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. In this work, a water immiscible room temperature ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent for liquid/liquid extraction of copper ions. Metal chelators, including dithizone, 8‐hydroxyquinoline, and 1‐(2‐pyridylazo)‐2‐naphthol, were employed to form neutral metal‐chelate complexes with copper ions so that copper ions were extracted from aqueous solution into [C₄mim][PF₆]. The parameters that affect the extraction of copper ions with this biphasic system were investigated. The extraction behavior in this novel biphasic system is shown to be consistent with that of traditional solvents. For example, the extraction with this biphasic system is strongly pH dependent. So, the extraction efficiency of coppers ion from an aqueous phase can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation and preconcentraction of copper ions can be accomplished by controlling the pH value of the extraction system. It appears that the use of ionic liquid as an alternate solvent system in liquid/liquid extraction of copper ions is very promising.     

A greener electrochromic liquid crystal based on ionic liquid electrolytes

An electrochromic liquid crystal (ECLC) material composed of only liquid crystal (LC) and ionic liquid (IL) was developed. The LC containing the substituted diphenylacetylene serves as electrochromic (EC) material to realise transmittance and colour change under the direct current (DC) field, while the IL with the designable cation and anion served as electrolyte. Herein, a series of IL electrolytes was screened to investigate how IL tunes the electro-optic performance of the ECLC cell. By testing the electrochemistry window of ILs in EC cells, IL with the [NTf₂]^? anion shows adequate electrochemical stability when the EC material undergoes oxidation and reduction. The electro-optic performance of ECLC containing 1-ethoxy-4-[2-(4-pentylphenyl) ethynyl]-benzene (PEB) and IL was then evaluated by UV-vis spectrometry under the control of an electrochemical work station. Compared with other PEB-IL, PEB-[Bmim][NTf₂] with [Bmim][NTf₂] electrolyte shows a satisfactory transmittance at low operating voltage. Furthermore, Pd NPs in situ formed in [Bmim][NTf₂] reduced the EC potential and improved the light scattering of the ECLC cell. In this work, we also designed a bifunctional device based on polymer dispersed liquid crystal (PDLC) that hosts electrochromic guest molecules, and analysed the electro-optical and electrochromic properties of LC electrolyte mixtures, in order to gain control of the incident daylight and glare in building and automotive applications.     

Calorimetric Study on the Ion Pairing and Aggregation of 1-Ethyl-3-Methylimidazolium bis(trifluoromethylsulfonyl)amide ([C2mim][NTf2]) and Related Ionic Liquids in the Low-Dielectric Constant Solvent Chloroform

A calorimetric study of dissolution of the ionic liquids (ILs) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([C₂mim][NTf₂]), 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([C₆mim][NTf₂]), and 1-hexyl-3-methylimidazolium tris(trifluoromethylsulfonyl)methide ([C₆mim][CTf₃]) into chloroform (CHCl₃) is presented with particular focus on [C₂mim][NTf₂]. The interpretation of the calorimetric data for [C₂mim][NTf₂] was aided by additional NMR self-diffusion measurements and viscosity measurements that through the Stokes–Einstein equation provided information about the average size of the species present. It is evident that the main equilibrium species are ion pairs and aggregates. An estimate for the enthalpy contribution from aggregate formation for [C₂mim][NTf₂] was found to be ?2.09 kJ per mol of added IL at 288.2 K and slightly decreasing in magnitude to ?1.11 kJ·mol^?1 at 318.2 K. While all three ILs release heat upon dissolution into CHCl₃, different temperature trends are observed demonstrating the fine balance of competing contributions from breaking IL interactions, cavity formation for the solutes to reside in, and the establishment of new solute–solvent interactions.     

γ辐照引发[Cnmim][NTf2]离子液体变色研究

1-烷基-3-甲基咪唑双三氟甲基磺酰胺型离子液体(C_nmim][NTf₂])被认为是最有希望用于核燃料循环中的分离试剂之一, 虽然其化学结构在辐照过程中变化不大, 但在受到γ辐照后会发生明显的变色, 因此有必要研究该类离子液体的变色原因. 本文以⁶⁰Co为辐照源, 系统研究了辐照后不同C(1)－烷基链长和咪唑环上C(2)位上的H被甲基取代后离子液体的紫外-可见(UV-Vis)吸收光谱行为, 并结合辐照后离子液体荧光光谱和质谱的变化, 分析了导致该类离子液体辐照后颜色加深的原因. 结果表明, 随着咪唑环上C(1)―烷基链长度和剂量增大, 离子液体颜色加深; 而C(2)位上的H被甲基取代后颜色明显变浅. 辐照后咪唑型离子液体的变色主要来自于辐照后产生的烷基侧链含双键的咪唑阳离子, 咪唑阳离子二聚体和含氟咪唑化合物. 此外, γ辐照引起咪唑阳离子易发生π-π堆积, 而聚集态含量增加也会引起颜色加深.     

Diffusion Coefficients of Imidazolium Based Ionic Liquids in Aqueous Solutions

Diffusion coefficients of the ionic liquids [C₂MIM][EtSO₄], [C₄MIM][OcSO₄], [C₂MIM][NTf₂] and [C₄MIM][NTf₂] in water at high dilution have been measured using the Taylor dispersion technique. Data on the diffusion coefficients have been obtained for each solute at six temperatures between 288 and 313 K. The data have been fitted by the Arrhenius equation and activation energies of diffusion have been determined. Effective radii of the ionic liquid molecules have also been obtained using the Stokes–Einstein relationship.     

Isotope effects on miscibility of 1-alkyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imides with aromatic hydrocarbons

The liquid–liquid miscibility temperatures as a function of composition and deuterium substitution have been experimentally determined for the binary mixtures of 1-decyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imide, [C₁₀MIM][NTf₂], and 1-dodecyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imide, [C₁₂MIM][NTf₂] with benzene and toluene and their deuterated forms. All systems exhibit upper critical solution temperatures (UCSTs) and better miscibility for ionic liquids with longer alkyl chain. The interchange of benzene for toluene results in worse miscibility for [C₁₀MIM][NTf₂] and better for [C₁₂MIM][NTf₂]. Deuteration of the aromatics leads to better miscibility in each case. The sign of the isotope effect is in agreement with expectations and its value seems to be seriously affected by the neighborhood of the hypercritical state.     

Ionic Liquid‐based Microchannels for Highly Sensitive and Fast Amperometric Detection of Toxic Gases

Ionic liquid (IL)‐based microchannels sensors have been fabricated and employed for the detection of toxic ammonia (NH₃) and hydrogen chloride (HCl) gases, with enhanced sensitivity and response times compared to conventional electrodes. Electrochemical techniques were employed to understand the behaviour of these highly toxic gases in two ionic liquids, [C₄mpyrr][NTf₂] and [C₂mim][NTf₂], on a gold modified microchannels electrode. The limits of detection (LODs) obtained in [C₄mpyrr][NTf₂] for NH₃ (3.7 ppm) and in [C₂mim][NTf₂] for HCl (3.6 ppm) were lower than the current Occupational Safety and Health Administration Permissible Exposure Limit (OSHA PEL) for the two gases (25 ppm for NH₃ and 5 ppm for HCl). The response time of the sensor is 15 s with a sensitivity of 143 nA ppm^?1 and 14 nA ppm^?1 for HCl and NH₃, respectively. These results demonstrate the superiority of IL‐based microchannels sensors for detecting toxic gases, when compared to commercially available sensors or traditional IL‐based sensor designs, where high sensitivity or fast response time is still a challenge.     

Ideal and non-ideal behaviour of {1-butyl-1-methylpyrrolydinium bis(trifluoromethylsulfonyl)imide + γ-butyrolactone} binary mixtures

Density, electrical conductivity and viscosity of binary liquid mixtures of 1-butyl-1-methylpyrrolydinium bis(trifluoromethylsulfonyl)imide, [bmpyrr][NTf₂], with γ-butyrolactone (GBL) were measured at temperatures from (293.15 to 323.15) K and at atmospheric pressure over the whole composition range. Excess molar volumes have been calculated from the experimental densities and fitted with the Redlich–Kister polynomial equation. These values are positive over the whole range of ionic liquid mole fraction and at all temperatures. In the range between 0.55 and 0.6 [bmpyrr][NTf₂] mole fraction, an ideal behaviour of the ionic liquid mixture with molecular solvent was observed for the first time. Other volumetric properties, such as isobaric thermal expansion coefficients, partial molar volumes and partial molar volumes at infinite dilution have been also calculated, in order to obtain information about interactions between GBL and selected ionic liquid. Positive values of these properties for both components also indicate weaker interactions between GBL and IL compared to the pure components. From the viscosity results, the Angell strength parameter was calculated and found to be 3.24 indicating that [bmpyrr][NTf₂] is a “fragile” liquid. From the volumetric and transport properties obtained, formation of the [bmpyrr]⁺ micellar structures was also discussed. All the results are compared to those obtained for imidazolium-based ionic liquid with GBL.     

Volatility of molten salts [Ph4P][NTf2] and Cs[NTf2]

The two ionic compounds [Ph₄P][NTf₂] and Cs[NTf₂] were qualified to be suitable liquid materials for different high temperature applications. Development and optimization of these application techniques require knowledge of the thermodynamic properties of vaporization. Vapor pressures and vaporization enthalpies have been measured by using quartz-crystal microbalance. Solubility parameters and miscibility of ionic liquids in practically relevant solvents were assessed.     

Speciation of Aluminium in Mixtures of the Ionic Liquids [C3mpip][NTf2] and [C4mpyr][NTf2] with AlCl3: An Electrochemical and NMR Spectroscopy Study

This paper reports on the electrodeposition of aluminium on several substrates from the air‐ and water‐stable ionic liquids 1‐propyl‐1‐methylpiperidinium bis(trifluoromethylsulfonyl)amide ([C₃mpip][NTf₂]) and 1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([C₄mpyr][NTf₂]), which contain anhydrous AlCl₃. At an AlCl₃ concentration of 0.75 molal, no evidence for aluminium electrodeposition was observed in either system at room temperature. However, aluminium electrodeposition becomes feasible upon heating the samples to 80 °C. Aluminium electrodeposition from bis(trifluoromethylsulfonyl)amide‐based ionic liquids that contain AlCl₃ has previously been shown to be very dependent upon the AlCl₃ concentration and has not been demonstrated at AlCl₃ concentrations below 1.13 molal. The dissolution of AlCl₃ in [C₃mpip][NTf₂] and [C₄mpyr][NTf₂] was studied by variable‐temperature ²⁷Al NMR spectroscopy to gain insights on the electroactive species responsible for aluminium electrodeposition. A similar change in the aluminium speciation with temperature was observed in both ionic liquids, thereby indicating that the chemistry was similar in both. The electrodeposition of aluminium was shown to coincide with the formation of an asymmetric four‐coordinate aluminium‐containing species with an ²⁷Al chemical shift of δ=94 and 92 ppm in the [C₃mpip][NTf₂]–AlCl₃ and [C₄mpyr][NTf₂]–AlCl₃ systems, respectively. It was concluded that the aluminium‐containing species that give rise to these resonances corresponds to the electroactive species and was assigned to [AlCl₃(NTf₂)]^?.     

Copper(I) and Silver(I) Bis(trifluoromethanesulfonyl)imide and Their Interaction with an Arene,Diverse Olefins,and an NTf2−‐Based Ionic Liquid

The chemistry of coinage metal bis(triflyl)imides of technological interest, CuNTf₂ and AgNTf₂, their synthesis and complexes with excess of comparatively weakly coordinating NTf₂^? as well as with ether, olefins, and the arene mesitylene are described. The existence of the solvent‐free pure phase [CuNTf₂]_∞ has not been evidenced so far. Contrary to the literature, in which the preparation of [CuNTf₂]_∞ is supposed to be carried out by reacting mesityl copper, [Cu(Mes)]₅, and HNTf₂, we found that in fact this reaction leads reproducibly to the interesting copper diarene sandwich complex [Cu(η³‐MesH)₂][Cu(NTf₂)₂] ( 1 ) (MesH=1,3,5‐trimethylbenzene). The unexpectedly stable molecular etherate [Cu(Et₂O)(NTf₂)] ( 2 ) turned out to be the best precursor for CuNTf₂ having only an inert and easily exchangeable solvent ligand. The coordination mode of NTf₂^? in 1 and 2 as well as in the hitherto unknown crystalline phase of [AgNTf₂]_∞ ( 3 ) is described. The complex formation, which takes place when dissolving 2 or 3 in the room temperature ionic liquid (RTIL) [emim]NTf₂ ([emim]⁺=1‐ethyl‐3‐methylimidazolium), has been studied. Furthermore, the reaction of 1 – 3 towards the diolefins 1,5‐cyclooctadiene (COD), 2,5‐norbornadiene (NBD) and isoprene (2‐methylbuta‐1,3‐diene) and towards ethylene has been investigated. The products 4 – 13 of these conversions have been isolated and fully characterized by NMR‐ and IR spectroscopies, mass spectrometry, and elemental‐ and XRD analyses. The potential of [Cu(η³‐MesH)₂][Cu(NTf₂)₂] ( 1 ), [Cu(Et₂O)(NTf₂)] ( 2 ) and [AgNTf₂]_∞ ( 3 ) as well as of [emim][M(NTf₂)₂] (M=Cu 4 , Ag 5 ) as chemisorbers for ethylene was studied by NMR spectroscopy.     

Microwave-accelerated Claisen rearrangement in bicyclic imidazolium [b-3C-im][NTf2] ionic liquid

With microwaves, a chemically stable ionic liquid [b-3C-im][NTf₂] recently developed in our laboratory was used as solvent and successfully applied to accelerate Claisen rearrangement reactions at high temperatures. In the presence of Lewis acid MgCl₂, these thermal rearrangements could be achieved in similar reaction times but at lower temperature. For the microwaved reactions studied in this work, without scarifying isolated yields, the reaction times were significantly reduced from hours (by conventional heating) to ≤3 min. Our result also demonstrated that [b-3C-im][NTf₂] ionic liquid was a useful solvent substitute and could be recycled multiple times for the studied rearrangement reaction at elevated temperatures.     

A comprehensive study of {γ-butyrolactone + 1-methyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide} binary mixtures

Density, electrical conductivity and viscosity of binary liquid mixtures of γ-butyrolactone, (GBL) with 1-methyl-3-propylimidazolium bis(trifluoromethylsulfonyl)imide, [pmim][NTf₂], were measured at different temperatures from (293.15 to 323.15) K and at atmospheric pressure (p = 0.1 MPa) over the whole composition range. Excess molar volumes have been calculated from the experimental densities and were fitted with Redlich–Kister’s polynomial equation. Other volumetric properties have been also calculated in order to obtain information about interactions between GBL and selected ionic liquid. All the results are compared with those obtained for binary mixtures of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [bmim][NTf₂], with GBL. From the viscosity measurements, the Angell strength parameter was calculated for pure ionic liquid indicating that [pmim][NTf₂] is a “fragile” liquid. Electrical conductivity results were discussed in the scope of Bahe–Varela theoretical model.