Improvement of thermoplasticity for s‐BPDA/PDA by copolymerization and blend with novel asymmetric BPDA‐based polyimides

Asymmetric biphenyl type polyimides (PI) derived from 2,3,3′,4′‐biphenyltetracarboxylic dianhydride (a‐BPDA) and p‐phenylenediamine (PDA) or 4,4′‐oxydianiline (ODA) show higher T_gs, and much better thermoplasticity than the corresponding isomeric PIs from symmetric 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA). In addition, a‐BPDA‐derived PIs are completely amorphous owing to their bent chain structures and highly distorted conformations, whereas the PIs from s‐BPDA are semicrystalline. a‐BPDA‐derived PIs possessing these properties or the a‐BPDA monomer were used as a flexible blend component or a comonomer to improve the insufficient thermoplasticity of semirigid s‐BPDA/PDA homo polymer. The blends composed of s‐BPDA/PDA (80%) with a‐BPDA‐derived PIs (20%), as well as the s‐BPDA/PDA‐based copolymer containing 20% a‐BPDA, showed a certain extent of thermoplasticity above the T_gs without causing a decrease in T_g. In addition, these blends and copolymer provided comparatively low thermal expansion coefficient (ca. 18 ppm). The improved film properties for the blends are related to good blend miscibility. On the other hand, when s‐BPDA/ODA was used as a flexible matrix polymer instead of a‐BPDA‐derived PIs, the 80/20 blend film annealed at 400°C exhibited no prominent softening at the T_g. This result arises from annealing‐induced crystallization of the flexible s‐BPDA/ODA component. Thus, these results revealed that a‐BPDA‐derived PIs are promising candidates as matrix polymers for semirigid s‐BPDA/PDA for the present purpose. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2499–2511, 1999     

Syntheses and properties of organosoluble polyimides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4, 7‐methanohexahydroindan

A series of organosoluble aromatic polyimides (PIs) was synthesized from 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4,7‐methanohexahydroindan (3) and commercial available aromatic dianhydrides such as 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA), 4,4′‐sulfonyl diphthalic anhydride (SDPA), or 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropanic dianhydride (6FDA). PIs (III_c–f), which were synthesized by direct polymerization in m‐cresol, had inherent viscosities of 0.83–1.05 dL/g. These polymers could easily be dissolved in N,N′‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF), pyridine, m‐cresol, and dichloromethane. Whereas copolymerization was proceeded with equivalent molar ratios of pyromellitic dianhydride (PMDA)/6FDA, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA)/6FDA, or BTDA/SDPA, or ½ for PMDA/SDPA, copolyimides (co‐PIs), derived from 3 and mixed dianhydrides, were soluble in NMP. All the soluble PIs could form transparent, flexible, and tough films, and they showed amorphous characteristics. These films had tensile strengths of 88–111 MPa, elongations at break of 5–10% and initial moduli of 2.01–2.67 GPa. The glass transition temperatures of these polymers were in the range of 252–311°C. Except for III_e, the 10% weight loss temperatures (T_d) of PIs were above 500°C, and the amount of carbonized residues of the PIs at 800°C in nitrogen atmosphere were above 50%. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1681–1691, 1999     

Synthesis of polyimides with lower H2O-absorption and higher thermal properties by incorporation of intramolecular H-bonding

To introduce intramolecular hydrogen bonds in the polyimides (PIs), 5(6)-amino-2-(5-aminopyridin-2-yl)-benzimidazole (PyPABZ) were designed and synthesized. The intramolecular interaction was indicated by Fourier transform infrared when different copolyimides were prepared with 4,4′-oxydianiline and PyPABZ. These modified poly(benzimidazole imide)s eliminate the problem of high water absorption for benzimidazole (BI)-containing PIs in the materials applications. Moreover, the high packing coefficient and rigidity of these copolyimides caused by the strong intramolecular interaction from the H-bonding and the resulting PIs exhibited outstanding thermal properties such as high glass-transition temperature (T_g) and low coefficient of thermal expansion.     

Polyimides with low coefficient of thermal expansion derived from diamines containing benzimidazole and amide: Synthesis,properties, and the N-substitution effect

Three novel diamines, incorporating benzimidazole and amide moieties, namely 4-amino-N-(5-amino-benzimidazol-2-yl)-benzamide (6a), 4-amino-N-(5-amino-1- methyl-benzimidazol-2-yl)-benzamide (6b), and 4-amino-N-(5-amino-1-phenyl -benzimidazol-2-yl)-benzamide (6c), were designed and synthesized. A series of poly(benzimidazole-amide-imide) (PBIAI) films were prepared from the resulting diamines and 4,4-biphthalic dianhydride (BPDA). These flexible polyimides (PIs) showed high glass transition temperatures (T_g = 353–379°C), low coefficients of thermal expansion (CTE = 3.7–12.3 ppm K⁻¹) and good mechanical properties (σ = 152–207 MPa and E = 4.5–7.7 GPa), promising candidates for applications in flexible-display substrates. Furthermore, the data guided a feasible method to enhance T_g and reduce CTE by introducing benzimidazole and amide units into PI main chains, and the effect of different N-substituents on performance was revealed.     

Novel Non‐Coplanar and Tertbutyl‐Substituted Polyimides: Solubility,Optical, Thermal and Dielectric Properties

A novel aromatic diamine monomer bearing tertbutyl and 4‐tertbutylphenyl groups, 3,3′‐ditertbutyl‐4,4′‐diaminodiphenyl‐4′′‐tertbutylphenylmethane (TADBP), was prepared and characterized. A series of non‐coplanar polyimides (PIs) were synthesized via a conventional one‐step polycondensation from TADBP and various aromatic dianhydrides including pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (OPDA), 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) and 4,4′‐(hexafluoroisopropylidene)dipthalic anhydride (6FDA). All PIs exhibit excellent solubility in common organic solvents such as N,N‐dimethylformamide (DMF), N,N‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), dimethyl sulfoxide (DMSO), chloroform (CHCl₃), tetrahydrofuran (THF), and so on. Furthermore, the obtained transparent, strong and flexible polyimide films present good thermal stability and outstanding optical properties. Their glass transition temperatures (T_gs) are in the range of 298 to 347°C, and 10% weight loss temperatures are in excess of 490°C with more than 53% char yield at 800°C in nitrogen. All the polyimides can be cast into transparent and flexible films with tensile strength of 80.5–101 MPa, elongation at break of 8.4%–10.5%, and Young's modulus of 2.3–2.8 GPa. Meanwhile, the PIs show the cutoff wavelengths of 302–356 nm, as well as low moisture absorption (0.30% –0.55%) and low dielectric constant (2.78–3.12 at 1 MHz).     

Synthesis and properties of poly(amic acid)s and polyimides based on 2,2′,6,6′‐biphenyltetracarboxylic dianhydride

Poly(amic acid)s (PAAs) having the high solution stability and transmittance at 365 nm for photosensitive polyimides have been developed. PAAs with a twisted conformation in the main chains were prepared from 2,2′,6,6′‐biphenyltetracarboxylic dianhydride (2,2′,6,6′‐BPDA) and aromatic diamines. Imidization of PAAs was achieved by chemical treatment using trifluoroacetic anhydride. Among them, the PAA derived from 2,2′,6,6′‐BPDA and 4,4′‐(1,3‐phenylenedioxy)dianiline was converted to the polyimide by thermal treatment. The heating at 300 °C under nitrogen did not complete thermal imidization of PAAs having glass‐transition temperatures (T_g)s higher than 300 °C to the corresponding PIs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6385–6393, 2006     

Phosphinated phenols from acid‐fragmentation of bisphenols and their unsymmetrical diamine derivatives for copolyimides

Four novel diamines (9–12) were prepared by a two‐step procedure from phosphinated phenols (1–4) that were prepared from acid‐fragmentation of four bisphenols, including bisphenol A, 4,4′‐isopropylidenebis(2,6‐dimethylphenol), cis(4‐hydroxyphenyl)cyclohexane, and 9,9′‐bis(4‐hydroxyphenyl)fluorene, followed by nucleophilic addition of 9,10‐dihydro‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO). Copolyimides based on (9–12) /4,4′‐diaminodiphenyl ether (ODA)/dianhydride were prepared. The structure‐property relationship on the copolyimides was discussed. Due to the structural similarity, (9) /ODA‐based copolyimides were compared with (10) /ODA‐based copolyimides, while (11) /ODA‐based copolyimides were compared with (12) /ODA‐based copolyimides. The dimethyl substitutents cause (10) /ODA‐based copolyimides to display higher T_g, modulus, dimensional stability, contact angle, and better solubility than (9) /ODA‐based copolyimides. (12) /ODA‐based copolyimides that exhibit fluorene moieties display higher T_g and thermal stability, but a lower contact angle and poorer solubility than (11) /ODA‐based copolyimides that exhibit cyclohexane moieties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 390–400     

Synthesis and properties of new block copolymers based on polydimethylsiloxane and tetraphenylethylene-containing polyimide

New polydimethylsiloxane (PDMS)-polyimide block copolymers were synthesized by the solution polycondensation of aminopropyl-terminated polydimethylsiloxane, 1,1-bis(4-aminophenyl)-2,2-diphenylethylene, and 3,3′,4,4′-benzophenonetetracarboxylic dithioanhydride in pyridine. New 1,3-bis(3-aminopropyl)tetramethyldisiloxane (BADS)-based random copolyimides were also prepared. The inherent viscosities of all the random and block copolyimides were in the range of 0.13–0.90 dL/g in N-methyl-2-pyrrolidone. These copolymers were soluble in N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol. All the BADS-based random copolymers and PDMS-containing copolymers with PDMS content above 42 wt % were soluble in tetrahydrofuran and chloroform. Transparent or somewhat cpaque films were prepared by casting from the reaction solutions. The BADS-based random copolyimides had one glass transition temperature (T_g) in the whole composition ranges, which showed single phase nature of the copolymers. On the other hand, the PDMS-polyimide block copolymers had double T_gS, indicating phase-separated morphology. The block copolymers containing PDMS content above 73 wt % behaved like a high temperature elastomer. © 1993 John Wiley & Sons, Inc.     

Organosoluble polyimides and copolyimides based on 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane and aromatic dianhydrides

1,1‐Bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane (BAPPE) was prepared through nucleophilic substitution reaction of 1,1‐bis(4‐hydroxyphenyl)‐1‐phenylethane and p‐chloronitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Novel organosoluble polyimides and copolyimides were synthesized from BAPPE and six kinds of commercial dianhydrides, including pyromellitic dianhydride (PMDA, I_a ), 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA, I_b ), 3,3′,4,4′‐ biphenyltetracarboxylic dianhydride (BPDA, I_c ), 4,4′‐oxydiphthalic anhydride (ODPA, I_d ), 3,3′,4,4′‐diphenylsulfonetetracarboxylic dianhydride (DSDA, I_e ) and 4,4′‐hexafluoroisopropylidenediphthalic anhydride (6FDA, I_f ). Differing with the conventional polyimide process by thermal cyclodehydration of poly(amic acid), when polyimides were prepared by chemical cyclodehydration with N‐methyl‐2‐pyrrolidone as used solvent, resulted polymers showed good solubility. Additional, I_a,b were mixed respectively with the rest of dianhydrides (I_c–f) and BAPPE at certain molar ratios to prepare copolyimides with arbitrary solubilities. These polyimides and copolyimides were characterized by good mechanical properties together with good thermal stability. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2082–2090, 2000     

Synthesis and characterization of hyperbranched polyimides with good organosolubility and thermal properties based on a new triamine and conventional dianhydrides

A triamine monomer, 1,3,5‐tris(4‐aminophenoxy)benzene (TAPOB), was synthesized from phloroglucinol and 4‐chloronitrobenzene, and it was successfully polymerized into soluble hyperbranched polyimides (HB PIs) with commercially available dianhydrides: 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA). Different monomer addition methods and different monomer molar ratios resulted in HB PIs with amino or anhydride end groups. From ¹H NMR spectra, the degrees of branching of the amino‐terminated polymers were estimated to be 0.65, 0.62, and 0.67 for 6FDA–TAPOB, ODPA–TAPOB, and BTDA–TAPOB, respectively. All polymers showed good thermal properties with 10% weight‐loss temperatures (T₁₀'s) above 505 °C and glass‐transition temperatures (T_g's) of 208–282 °C for various dianhydrides. The anhydride‐terminated HB PIs showed lower T₁₀ and T_g values than their amino‐terminated counterparts. The chemical conversion of the terminal amino or anhydride groups of the 6FDA‐based polyimides into an aromatic imido structure improved their thermal stability, decreased their T_g, and improved their solubility. The HB PIs had moderate molecular weights with broad distributions. The 6FDA‐based HB PIs exhibited good solubility even in common low‐boiling‐point solvents such as chloroform, tetrahydrofuran, and acetone. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3804–3814, 2002     

Synthesis and characterization of high refractive index polyimides derived from 2,5‐Bis(4‐Aminophenylenesulfanyl)‐3,4‐Ethylenedithiothiophene and aromatic dianhydrides

The authors describe the synthesis and characterization of the polyimide (PI) series containing a 2,5‐bis(4‐aminophenylenesulfanyl)‐3,4‐ethylenedithiothiophene (APSEDTT) moiety in their main chain. The APSEDTT monomer with high sulfur content was prepared and polymerized with several aromatic dianhydrides such as 4,4′‐[p‐thio bis(phenylenesulfanyl)]diphthalic anhydride (3SDEA), 4,4′‐biphthalic anhydride (BPDA), and 4,4′‐oxydiphthalic anhydride (ODPA) by the traditional two‐step polycondensation procedure. All PIs exhibited high transparency, higher than 75% at 550 nm for a thickness of about 20 μm and good thermal properties such as thermal decomposition temperatures (T_10%) in the range of 409–521 °C. In addition, the PIs have extraordinarily excellent optical properties in refractive index and birefringence as originally designed. In particular, the PI derived from APSEDTT and 3SDEA showed a high refractive index (1.7586), and a low birefringence (0.0087) because of their very high sulfur content (27.7%). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 944–950     

Nanoindentation studies of polyimide thin films with various internal linkages in the diamine component

Polyimide thin films were synthesized from 3,3′,4,4′‐biphenyltetracarboxylic acid dianhydride (BPDA) and four different diamines (p‐phenylene diamine, 4,4′‐oxydiphenylene diamine, 4,4′‐biphenylene diamine, and 4,4′‐sulfonyldiphenylene diamine). The nanoindentation behavior of the resulting polyimides, namely, poly(p‐phenylene biphenyltetracarboximide) (BPDA‐PDA), poly(4,4′‐biphenylene biphenyltetracarboximide) (BPDA‐BZ), poly(4,4′‐oxydiphenylene biphenyltetracarboximide) (BPDA‐ODA), and poly(4,4′‐sulfonyldiphenylene biphenyltetracarboximide) (BPDA‐DDS), were investigated. Also, the morphological properties were characterized with a prism coupler and wide‐angle X‐ray diffraction and were correlated to the nanoindentation studies. The nanoindentation behavior and hardness varied quite significantly, depending on the changes in the chemical and morphological structures. The hardness of the polyimide thin films increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐BZ < BPDA‐PDA. For all the polyimide thin films, except that of BPDA‐BZ, the hardness decreased with an increase in the load. The birefringence, a measure of the molecular in‐plane orientation, increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐PDA < BPDA‐BZ. The X‐ray diffraction studies revealed that the crystallinity of the polyimide thin films varied with the changes in the chemical structure. The studies showed that the indentation response with an applied load and the hardness by nanoindentation for the BPDA‐based polyimides were closely related to the morphological structure. The nanoindentation and birefringence results revealed that the mechanical properties of the polyimide thin films were dependent on the crystallinity, which arose because of the chain order along the chain axis and the molecular packing order. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 861–870, 2004     

Preparation of silicon containing polymers. II.. Effect of structure on the thermal stability of organosilicon aramids

Two silicon-containing acid dichlorides, bis(4-chlorocarbonylphenyl)dimethylsilane and bis(4-chlorocarbonylphenyl)diphenylsilane, were synthesized and reacted with 1,3-phenylene diamine, 1,4-phenylene diamine, 4,4′-diaminodiphenyl, 4,4′-diaminodiphenyl methane 4,4′-diaminodiphenyl ether, and 4,4′-diaminodiphenyl sulfone in the preparation of 12 structurally different high molecular weight aromatic polyamides. A low-temperature interfacial polycondensation technique was used. Most of the polyamides formed tough, transparent, flexible films and were characterized by solubility, solution viscosity, infrared spectroscopy (IR), and glass transition temperature (T_g). The thermal behavior of these aramids was studied by dynamic thermogravimetry. The effect of diamine and acid dichloride structure on the aramids properties is also discussed.     

Synthesis and Characterization of Fluorinated Polyimide Derived from 3,3′‐Diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane

A novel aromatic diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminodiphenyl‐3′′,4′′‐difluorophenylmethane (PAFM), was successfully synthesized by coupling of 2‐isopropylaniline and 3,4‐difluorobenzaldehyde. The aromatic diamine was adopted to synthesize a series of fluorinated polyimides by polycondensation with various dianhydrides: pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA) and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA) via the conventional one‐step method. These polyimides presented excellent solubility in common organic solvents, such as N,N‐dimethylformamide (DMF), N,N‐dimethyl acetamide (DMAc), dimethyl sulfoxide (DMSO), N‐methyl‐2‐pyrrolidone (NMP), chloroform (CHCl₃), tetrahydrofuran (THF) and so on. The glass transition temperatures (T_g) of fluorinated polyimides were in the range of 260–306°C and the temperature at 10% weight loss in the range of 474–502°C. Their films showed the cut‐off wavelengths of 330–361 nm and higher than 80% transparency in a wavelength range of 385–463 nm. Moreover, polymer films exhibited low dielectric properties in the range of 2.76–2.96 at 1 MHz, as well as prominent mechanical properties with tensile strengths of 66.7–97.4 MPa, a tensile modulus of 1.7–2.1 GPa and elongation at break of 7.2%–12.9%. The polymer films also showed outstanding hydrophobicity with the contact angle in the range of 91.2°–97.9°.     

Synthesis and characterization of new polyimides containing calix[4]arenes in the polymer backbone

Two diaminocalix[4]arene monomers were synthesized from p-tert-butylcalix[4]arene through a 4-step reaction sequence. New copoly(amic acid)s containing calix[4]arene moieties on the polymer backbone were successfully synthesized in N-methyl-2-pyrrolidone by polycondensations of 4,4′-oxydiphthalic anhydride (ODPA) with the diaminocalix[4]arene monomers using 4,4′-oxydiphenylene diamine (ODA) as a comonomer. These copoly(amic acid)s were soluble in aprotic polar solvents, so that they can be processed in various ways. The copoly(amic acid) precursors were thermally converted to the corresponding copolyimides in films. The copolyimide films are amorphous, but insoluble in common solvents. They are thermally stable up to 366°C. The copolyimides exhibit relatively high TEC's, low T_g's, low refractive index, low dielectric constant, low optical anisotropy, low dielectric anisotropy, and low water uptake, compared to those of conventional ODPA-ODA polyimide. These property characteristics were interpreted in regard to bulky, cone-like calix[4]arene moieties and their effects on the chain conformation and morphological structure. The processability and property characteristics support that both of the copolyimides containing calix[4]arene moieties are potential candidate materials suitable for membranes, antioxidant additives, chemical sensor devices, and microelectronic devices. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2013–2026, 1999     

Synthesis and thermal properties of aryl-substituted rod-like polyimides

This article describes the synthesis and thermal characterization of novel aryl-substituted rod-like homopolyimides. Synthetic aspects of monomer syntheses and one-step polymer synthesis in m-cresol are presented. Polyimides with rod-like chain structure are based on monophenylated pyromellitic dianhydride (MPPMDA), diphenylated pyromellitic dianhydride (DPPMDA), and as rod-like diamine units on phenylated para-phenylene diamine and 1,1′-binaphthyl-4,4′-diamine. As partial flexible units, which have the possibility to be converted into an extended chain conformation, commercially available 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and 3,4′-oxydianiline (3,4′-ODA) were used. The polyimides were investigated with respect to solution properties and thermal behavior. © 1993 John Wiley & Sons, Inc.     

Study on side‐chain second‐order nonlinear optical polyimides based on novel chromophore‐containing diamines. II. Copolyimides possessing direct photolithographic features

Second‐order nonlinear optical copolyimides were prepared from a novel chromophore‐containing diamine, 4‐nitro‐4′‐[N‐(4,6‐di‐4‐aminophenylamino)‐1,3,5‐triazin‐2‐yl]aminoazobenzene, a codiamine, 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane, and benzophenone‐3,3′,4,4′‐tetracarboxylic dianhydride by a traditional two‐step process, which includes a solution polycondensation followed by a chemical imidization. Some of the polyimides (PIs) obtained possessed direct photolithographic features, and good photolithographic patterns were easily obtained. All PIs exhibited high‐glass transition temperatures (235–246 °C) and high thermal‐decomposition temperatures. They were also soluble in strong polar aprotic solvents such as N‐methyl‐2‐pyrrolidone, dimethylacetamide, dimethylformamide, dimethyl sulfoxide, and γ‐butyrolactone. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1419–1425, 2001     

Synthesis and comparative study on polyetherimides from isomeric 4,4′-isopropylidenediphenoxy bis(phthalic anhydride)s

Two isomers of commercial 4,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (4,4′-BPADA), that is, 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,4′-BPADA) and 3,3′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,3′-BPADA), were synthesized through aromatic nucleophilic substitution from nitrophthalonitrile and bisphenol A. 3,4′-BPADA was first synthesized from two intermediates, that is, 3-(4-[4-hydroxyphenylisopropylidene] phenoxy) phthalonitrile (3-BPADN) and 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalonitrile) (3,4′-BPATN). The corresponding three series of polyetherimides (PEIs) were prepared with two representative aromatic diamines (4,4′-oxydianiline and m-phenylenediamine (m-PDA)) via two-step procedure and chemical imidization. Isomeric polyimides showed T_gs from 206 to 256°C in nitrogen and T_d5%s from 488 to 511°C in argon, good mechanical properties (tensile moduli of 2.3–3.3 GPa, tensile strengths of 70–96 MPa, and elongations at break of 3.2%–5.1%), and good solubility. With the introduction of 3-substituted phthalimide unit, PEIs displayed higher T_g values, lower strengths and elongations, better solubility and larger d-spacings. The rheological properties of thermoplastic polyimide resins based on the BPADA isomers were investigated, which showed that polyetherimide PEI-3b derived from 3,3′-BPADA and m-PDA had the lowest melt viscosity among the isomers, indicating that the melt processibility had been greatly improved.     

Aromatic polyamides. III. Copoly(4,4′-oxanilideterephthalamide—4,4′-phenyleneterephthalamide): Synthesis,wet-spinning,fiber thermal characterization,and stability in sulfuric acid

Copoly(4,4′-oxanilideterephthalamide—4,4′-phenyleneterephthalamide) (A-202/PPD) was synthesized by reaction of 4,4′-diaminooxanilide, p-phenylenediamine, and terephthaloyl chloride in organic solvents. Copolymer inherent viscosities in H₂SO₄ as high as 10.3 were obtained. Isotropic copolymer solutions (4%—5% concentration) of A-202/40%–80% PPD were spun to fibers with tenacity/elongation/modulus at 1% extension in the 13–14 gpd/1.5%–2%/700–1000 gpd range. Oxamide and amide stabilities in 98–100% H₂SO₄ and 20% oleum were compared. Poly(4,4′-oxanilideterephthalamide) (A-202), A-202/PPD copolymers, and poly(4,4′-phenyleneterephthalamide) (PPT) were unstable in 20% oleum, but all proved relatively stable in 100% H₂SO₄. However, the oxamide linkage proved less stable than the amide linkage in 98% H₂SO₄. A-202 and A-202/PPD copolymers formed stable anisotropic spinning solutions in 1% oleum at 10–20% concentrations. Dynamic mechanical analyses (Vibron) showed no glass transition temperature (T_g) below 200°C. Dilatometric measurement of A-202/50% PPD revealed a T_g at 257°C. Differential thermal analyses of A-202/40–80% PPD exhibited endotherms at 470–480°C. Thermogravimetric analyses showed no significant weight loss below 400°C.     

Synthesis and characterization of highly refractive polyimides from 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] and various aromatic tetracarboxylic dianhydrides

An aromatic sulfur‐containing diamine 4,4′‐thiobis[(p‐phenylenesulfanyl) aniline] (3SDA) was synthesized and polymerized with a sulfur‐containing dianhydride 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA) and three nonsulfur aromatic tetracarboxylic dianhydrides, respectively to afford four poly(amic acid)s (PAAs) with the inherent viscosities of 0.54–1.04 dL/g. Flexible and tough polyimide (PI) films obtained from the PAA precursors showed good thermal, mechanical, and optical properties. The glass transition temperatures (T_gs) of the PIs ranged from 179.1–227.2 °C determined by differential scanning calorimetry (DSC), and 173.8–227.3 °C by dynamic mechanical analysis (DMA), depending on the dianhydride used. The 10% weight loss temperatures were in the range of 500–536 °C, showing high intrinsic thermal‐resistant characteristics of the PI films. The PI films also showed good optical transparency above 500 nm, which agreed well with the calculated absorption spectra using the time‐dependent density functional theory. The average refractive indices (n_av) measured at 632.8 nm were 1.7191–1.7482, and the in‐plane/out‐of‐plane birefringences (Δn) were 0.0068–0.0123. The high refractive indices originate from the high sulfur contents, good molecular packing, and the absence of bulky structures. The relatively small birefringence mainly results from the flexible thioether linkages structures of the diamine. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5606–5617, 2007