Cyclopolycondensations. VII. Preparation of aromatic poly(ureido acids) by the low-temperature solution polymerization and cyclodehydration to fully aromatic polyquinazolinediones

Fully aromatic polyquinazolinediones (IV) of high molecular weight were obtained by thermal cyclodehydration of aromatic poly(uredio acids) (III) prepared by the polyaddition reaction of 4,4′-diaminobiphenyl-3,3′-dicarboxylic acid (I) with aromatic diisocyanates (II). From the kinetic study of reactions of model systems (anthranilic acid with phenyl isocyanate) in the presence of a variety of basic catalysts, it was established that tertiary amines had the highest catalytic activity for the formation of ureido linkage. The optimum polymerization conditions were determined by the study of reaction variables such as monomer concentration, polymerization temperature, monomer ratio, and catalyst concentration. The effect of polarity and purity of organic solvents and reactants was also studied.     

Lyotropic para-linked aromatic poly(amic ethyl ester)s

The synthesis, characterization and application of lyotropic precursor polymers for polyimides, poly(amic ethyl ester)s (PAE) are presented. By the use of non-coplanar and para-linked monomers, rigid-rod PAEs are synthesized in a typical polycondensation reaction yielding liquid crystalline solutions at concentrations of 30-40 wt% in NMP at 100°C. These lyotropic solutions permit for the first time the fabrication of orientation PAE layers by shear which are thermally converted to the corresponding polyimide. The bulk orientation in the thin films is characterized by spectroscopic methods. In addition the lyotropic solution is spun into fibers in a dry-jet wet spinning process. The obtained fiber orientation is characterized by tensile tests and wide angle X-ray scattering.     

Aromatic poly(amic acids): Fundamental structural studies

Aromatic poly(amic acids) derived from pyromellitic dianhydride and 4,4′,-diaminodiphenyl ether were characterized by dilute solution techniques. Number-average molecular weights M?_n of 13 samples ranged from 13,000 to 55,000 (DP 31–131). Weight-average molecular weights M?_w of 21 samples ranged from 9,900 to 266,000. The ratio M?_w/M?_n was between 2.2 and 4.8. Heterogeneous polymerization yielded higher molecular weight polymer than homogeneous polymerization. The molecular weight could be varied systematically by control of stoichiometric imbalance. Use of very pure monomers and solvent gave polymers of relatively high number-average molecular weight (～50, 000) and the most probable molecular weight distribution M?_w/M?_n = 2. Impure monomers and/or solvent resulted in lower number-average molecular weight (M?_n ? 20,000–30,000) and wider distributions (M?_w/M?_n = 3–5). The Mark-Houwink relation obtained was [η] = 1.85 × 10^?4M?_w^0.80 The exponent is characteristic of moderately extended solvated coils. The unperturbed chain dimensions (r₀² /M)^1/2 were 0.848 A., and the steric factor σ was 1.24 which is close to the limiting value of unity for an equivalent chain with free internal rotations. The sedimentation constant–molecular weight relation was S₀ = 2.70 × 10^?2M?_w^0.39. This exponent is consistent with the Mark-Houwink exponent.     

Complexes of amic acids with polar aprotic solvents. VI. System of hydrogen-bonds in complexes of amic acids and polyamic acids with amide solvents

It has been established through X-ray analysis of complexes of pyromellitedianylic acid with amide solvents that the type of the system of hydrogen-bonds and the solvate structure depend on the nature of these solvents. It is shown for solvates of poly(4,4-oxydiphenylene)pyromellite amic acid that mass spectrometric thermal analysis (MTA) may be used for the investigation of hydrogen-bonds formed in solid polyamic acid films. The MTA data may be employed to establish the mechanism of the effects of additives catalysing the solid-phase cyclodehydration of polyamic acids.

---

Zusammenfassung Durch röntgenanalyse von Komplexen von Pyromellit-dianilicsäure mit Amidlösungsmitteln wurde festgestellt, daß der Typs des Systems der Wasserstoffbindungen und die Solvatstruktur von der Natur dieser Lösungsmittel abhängt. Für Solvate der Poly-(4,4-oxydiphenilen) pyromellit-amicsäure wird gezeigt, daß die massenspektrometrische thermische Analyse (MTA) zur Untersuchung von in festen Polyamicsäurefilmen ausgebildeten Wasserstoffbindungen herangezogen werden kann. Die MTA-Daten können zur Ermittlung des Wirkungsmechanismus von die Festphasencyclodehydratisierung von Polyamicsäuren katalisierenden Additionen herangezogen werden.

---

, . , (4,4-) , , o , , .

     

Isomeric compositions in amide acids and poly(amic acid)s derived from 1-(trifluoromethyl)-2,3,5,6-benzenetetracarboxylic dianhydride

Two different poly(amic acid)s were synthesized by the polycondensations of 1-(trifluoromethyl)-2,3,5,6-benzenetetracarboxylic dianhydride (CF3DAN) with p-phenylene diamine and benzidine. In addition, an amide acid model compound was prepared from CF3DAN and aniline. Isomeric units in the poly(amic acid)s as well as the amide acid were investigated by ¹H and ¹³C-nuclear magnetic resonance (NMR) spectroscopies. Spectroscopic results indicate that the major isomeric component was a CF3-meta-isomeric unit centered on the aromatic carbon substituted with the trifluoromethyl group. In particular, the amide acid compound was determined to be composed of 80 mol % CF3-meta-isomer and 20 mol % H-meta-isomer. Therefore, for the poly(amic acid)s, the minor isomeric component is speculated to be a H-meta-isomeric unit rather than a para-isomeric unit. The result might result mainly from the strong electron-withdrawable and bulky trifluoromethyl substituent in the CF3DAN monomer. The strong electron withdrawability might significantly enhance the reactivities of the adjacent carbons in the monomer to the nucleophilic attack of the amino nitrogen in the aniline and diamines, and consequently overcome the role of the bulkyness, ultimately leading to the amide acid and poly(amic acid)s rich with the CF3-meta-isomeric unit. In addition, a portion of the imide form was detected in the dried AN-CF3DAM-AN amide acid. Thus, the formation of imide linkage might be involved in a small portion for the dried poly(amic acid)s. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1755–1765, 1998     

Synthesis and imidization of poly(amic methyl ester)s

The synthesis and characterization of a series of poly(amic methyl ester)s from five aromatic dianhydrides and a diamine, 4,4′-oxydianiline (ODA), are described. These poly(amic ester)s are obtained by the low-temperature polycondensation from dianhydrides derived diesterdiacyl chlorides and ODA in DMAc solution with the inherent viscosities in the 0.5–0.9 dL/g range. These precursors are readily soluble in aprotic solvents. A detailed thermal study of the imidization process is presented, based on dynamic and isothermal TGA measurements, FTIR spectroscopy, and dynamic mechanical analysis. © 1997 John Wiley & Sons, Inc.     

Fully aromatic poly(ether ketone)s bearing macrocycle pendants: Synthesis and crosslinking

This study reports a method to prepare fully aromatic poly(ether ketone) thermosets. The cyclization of 2′,5′‐dimethoxy[1,1′‐biphenyl]‐2,5‐diol and a difluoro monomer was carried out under pseudo high dilution condition. Two types of fully aromatic poly(ether ketone)s with macrocycle were successfully prepared by copolymerization of macrocycle of aryl ether ketone containing hydroxyphenyl groups, 4,4′‐(hexafluoroisopropylidene)diphenol (HFBPA), and 4,4‐difluorobenzophenone. The obtained copolymers have high molecular mass, good solubility, and high glass transition temperatures in the presence of CsF, the crosslinking reaction of copolymers occurred and afforded fully aromatic thermoset poly(aryl ether ketone)s by ring‐opening reaction driven by entropy. After crosslinking, these copolymers show much higher glass transition temperatures, excellent thermal stability, and better mechanical strength. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7002–7010, 2008     

Synthesis and properties of novel aromatic poly(ester amide)s derived from 1,5-bis(4-aminobenzoyloxy)naphthalene and aromatic dicarboxylic acids

A new naphthalene ring-containing bis(ester amine), 1,5-bis(4-aminobenzoyloxy)naphthalene (2), was synthesized from the condensation of 1,5-dihydroxynaphthalene with 4-nitrobenzoyl chloride followed by catalytic hydrogenation. A series of naphthalene-containing poly(ester amide)s having inherent viscosities of 0.34-0.82 dl/g were prepared by the direct phosphorylation polyamidation from bis(ester amine) 2 with various aromatic dicarboxylic acids. The poly(ester amide)s derived from terephthalic acid, 4,4′-biphenyldicarboxylic acid, 2,6-naphthalenedicarboxylic acid, and 4,4′-oxydibenzoic acid were semicrystalline and showed less solubility. The other polymers were amorphous and readily soluble in polar organic solvents and gave flexible and tough films via solution casting. Except for four examples, the poly(ester amide)s displayed discernible glass transitions between 190 and 227 °C by differential scanning calorimetry. These poly(ester amide)s did not show significant decomposition below 400 °C in nitrogen or air.     

Miscibility behavior and reequilibration of binary poly(amic acid) mixtures

Five poly (amic acid) solutions based on PMDA-PDA, PMDA-ODA, PMDA-6F, ODPA-ODA, and 6FDA-ODA were prepared in N-methylpyrrolidone at a polymer concentration of ca. 10 wt %. From these five poly (amic acid) solutions, six different binary blends were prepared: PMDA-PDA/PMDA-ODA, PMDA-PDA/PMDA-6F, PMDA-ODA/6FDA-ODA, PMDA-ODA/ODPA-ODA, PMDA-PDA/ODPA-ODA, and PMDA-PDA/6FDA-ODA. These blends were then characterized with respect to miscibility in the ternary state (polyamic acid-1/polyamic acid-2/N-methylpyrrolidone), the condensed state (ca. 70 wt % polymer), and the fully imidized state. All blends except for PMDA-PDA/PMDA-6F yielded homogeneous mixtures in the ternary solution of 10 wt % polymer concentration. The PMDA-PDA/PMDA-6F mixture eventually became homogeneous after 10 days of mixing at room temperature. Upon solvent evaporation (condensed state) and full cure (imidized state) two blends incorporating ODPA-ODA as one of the components exhibited apparent miscibility as evidenced by optical microscopy. The remaining blends exhibited large-scale phase separation upon solvent evaporation with no significant differences in the overall morphology between the condensed and imidized state. However, as in the case of the PMDA-PDA/PMDA-6F ternary system, the morphology in the condensed and imidized state was strongly dependent on the mixing time of the precursor poly(amic acid) components; the phase-separated domain size decreased with increasing mixing time, eventually leading to complete miscibility. These results are discussed with respect to the proposed “polymer-monomer” reequilibration reaction as well as its implications with respect to the preparation of polyimide molecular composites.     

聚酰胺酸酯的合成及性能研究

围绕刚性主链、高尺寸稳定性聚酰亚胺的制备,对聚酰胺酸酯的合成及酰亚胺化特性进行了研究。将制得的均苯二乙酯二酰氯与醚二胺进行聚合得到聚酰胺酸酯并与传统的预聚体——聚酰胺酸进行比较,得出聚酰胺酸酯性能较好,而酰亚胺化的温度要求较高。共聚中分别与间苯二胺或对苯二胺和醚二胺进行共聚,讨论了不同的二胺在共聚中的影响。     

Preparation of hemispherical polyimide particles by inverse emulsion technique from poly(amic acid) ammonium salts

Nonspherical polymer particles have attracted increasing attention recently. In this paper, micron-scale hemispherical polyimide (PI) particles were fabricated using water-soluble poly(amic acid) ammonium salts (PAAS) by a novel inverse emulsion technique. In the process, liquid paraffin was used as a continuous phase, the mixed solution of PAAS and water as a dispersed phase and sorbitan monooleate (Span80) as a surfactant. The research suggested that water as a stabilizing agent played an important role in forming stable emulsion. As the amount of water increased, stability of the emulsion increased gradually and morphology of PI particles transformed from sphere to ellipsoid, and finally to hemisphere. The concentration of PAAS solution and Span80 both affected the shape of particles, which changed from spherical to hemispherical by increasing the PAAS/Span80 concentration. The mechanism of forming hemispherical PI particles was discussed based on interfacial tension and interfacial free energy changes. Via adjusting the composition of the system to change the corresponding interfacial tension, we could get the particles with different morphologies. Furthermore, the change in structure characterized by FT-IR spectroscopy demonstrated that PAAS had been converted to PI after adding the dehydrating agent to the emulsion. And TGA results showed that the obtained PI particles had excellent thermal stability.     

Structure evolution and properties in a rigid polyimide prepared from its flexible poly(amic acid) precursor

Soluble poly(p-phenylene biphenyltetracarboxamic acid) precursor was converted to the polyimide by thermal imidization at various conditions. The structure evolution being occurred during its thermal imidization over 25–400°C was investigated as a function of imidization temperature and time by X-ray scattering with synchrotron radiation sources of Pohang Accelerator Laboratory in Korea and with conventional radiation sources. In addition, properties in the polyimide films were investigated by dynamic mechanical thermal analysis, stress-strain analysis, prism coupling, and residual stress analysis.     

Controlling surface roughness in vapor-deposited poly(amic acid) films by solvent-vapor exposure

A series of vapor-deposited poly(amic acid) (PAA) films were exposed to dimethyl sulfoxide (DMSO) vapors to investigate sorption kinetics and surface smoothing phenomena. Gravimetric sorption and secondary-ion mass spectrometry (SIMS) results are both consistent with frontal (case II) diffusion. These experiments suggest that the solvent front is defined by a sharp interface that delineates the swollen material from the unswollen material. Solvent-vapor smoothing was studied by first depositing PAA onto rough aluminum surfaces, and then, during solvent-vapor exposure, the surface topology was continuously monitored using a light interference microscope. The resulting time-dependent power spectra indicate that high-frequency defects smooth faster than low-frequency defects. This frequency dependence was further investigated by depositing PAA onto a series of sinusoidal surfaces and exposing them to solvent vapor inside a flow channel. The sinusoidal amplitudes decay exponentially with time, with decay constants that are proportional to the surface frequency. To explain the physics of surface smoothing, a two-parameter model is presented and agrees qualitatively with experimental data.     

Synthesis, characterization and hydrolytic stability of poly (amic acid) ammonium salt

A series of new poly (amic acid) ammonium salt (PAAS) precursors were prepared by incorporating different amounts of triethylamine (TEA) into terpolymer polyamic acid (PAA), which was synthesized by pyromellitic dianhydride (PMDA), 4,4’-oxydianiline (ODA) and p-phenylenediamine (PDA) in dimethylacetamide (DMAc). Then, the PAAS films were made by casting their solutions onto glass plates followed by the evaporation of the solvent. The chemical structure of PAAS films was confirmed by ¹H NMR and FTIR spectroscopy. Mechanical properties, intrinsic viscosities and solubility of PAAS precursors were examined, respectively. It was found that the intrinsic viscosity of PAA solution obviously decreased with storage time during 30 days, while no distinct changes were observed in the intrinsic viscosity of the PAAS (the mole ratio of TEA/repeating unit of PAA = 2/1) solution after 90 days. The results suggested that hydrolytic stability of the PAAS films was significantly improved as compared with that of PAA film due to the polyelectrolyte structure of PAAS. Moreover, the thermal and mechanical properties of polyimide (PI) films prepared from PAAS precursors were also investigated, respectively.     

Stereoregular poly(methacrylic acids)

A convenient method is described for the preparation of isotactic and syndiotactic poly(trimethylsilyl methacrylates) by using the monomer trimethyl silyl methacrylate and butyllithium initiation in toluene and tetrahydrofuran, respectively. The structure of these polymers enables complete hydrolysis to the corresponding poly(methacrylic acids), which were characterized with respect to tacticity and molecular weight. The asymmetric induction in toluene produced 89% isotactic polymer, while that in tetrahydrofuran gave polymer <90% syndiotactic and heterotactic in terms of triads. A method of fractionation of the polyelectrolytes by gel-permeation chromatography on a preparative scale was shown to be applicable.     

Prevalent intrinsic emission from nonaromatic amino acids and poly(amino acids)

Nonaromatic amino acids are generally believed to be nonemissive, owing to their lack of apparently remarkable conjugation within individual molecules. Here we report the intrinsic visible emission of nonaromatic amino acids and poly(amino acids) in concentrated solutions and solid powders. This unique and widespread luminescent characteristic can be well rationalized by the clustering-triggered emission(CTE) mechanism, namely the clustering of nonconventional chromophores(i.e. amino, carbonyl,and hydroxyl) and subsequent electron cloud overlap with simultaneous conformation rigidification. Such CTE mechanism is further supported by the single crystal structure analysis, from which 3 D through space electronic communications are uncovered.Besides prompt fluorescence, room temperature phosphorescence(RTP) is also detected from the solids. Moreover, persistent RTP is observed in the powders of exampled poly(amino acids) of ε-poly-L-lysine(.-PLL) after ceasing UV irradiation. These results not only illustrate the feasibility of employing the building blocks of nonaromatic amino acids in the exploration of new luminescent biomolecules, but also provide significant implications for the emissions of peptides and proteins at aggregated or crystalline states. Meanwhile, they may also shed lights on further understanding of autofluorescence from biological systems.     

Simple and easy recycling of poly(amic acid) gels through microwave irradiation

Poly(amic acid)s (PAAs), which are precursors of polyimides, often undergo gel formation during their synthesis or storage, and these insoluble gels have been discarded. In this work, we discovered that the gels could be converted to homogeneous PAA solutions by fast and simple microwave (MW) irradiation. The PAA gels were placed inside a domestic MW oven, and MW irradiation was carried out with 240 W for 2 min. The recycled PAA solutions afforded polyimide films, coatings, and powders. The polyimides prepared from the recycled PAA solutions exhibited higher glass transition temperatures (T_gs), decomposition temperatures, and char yields than comparison polyimides obtained from ordinary PAA solutions. Flexible free‐standing polyimide films were obtained by drop‐casting of the MW‐treated solutions and subsequent thermal imidization. Mechanical properties and dielectric constants were measured for the polyimide films and coatings, respectively. This new method has significant advantages for the environment, economy, and industry. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 981–987