Phenylated imide–quinoxaline copolymers

Phenylated, ordered imide–quinoxaline copolymers of high oxidative-thermal stability were prepared by one-step solution condensation of aromatic tetraamines with N,N′-bis(4-benzilyl)pyromellitimide. Polymerization in m-cresol leads to high molecular weight polymers that remain soluble. Thermal gravimetric analysis and isothermal decomposition at 400°C shows that these polymers are as stable as polyimides or polyquinoxalines. The polymer decomposition temperatures range between 495 and 550°C, depending upon structure. Also, the rate of isothermal decomposition at 400°C in air showed a strong dependency of weight loss on structure. Tough films were cast from solution.     

Self-regulating polycondensations. IV. Ordered oxadiazole-imide copolymers

Ordered oxadiazole-imide copolymers are prepared from simple aminobenzhydrazide monomers by a step-wise reaction which begins with the condensation of a diacid chloride to produce in situ a diamine containing hydrazide linkages. The in situ diamine is then reacted with a dianhydride to yield an ordered hydrazide-amic-acid copolymer; this precursor is converted by heating to the ordered heterocycle copolymer. Polymers prepared via this manner are identical in properties to those obtained by the reaction of a dianhydride with a diamine containing hydrazide linkages preformed by a straight forward synthesis from a dinitro precursor. Fibers spun from the soluble precursor polymers were converted via cyclodehydration to thermally stable fibers. Another polyoxadiazole-imide was produced in similar fashion; e.g., an aminobenzhydrazide was reacted with the acid chloride of trimellitic anhydride to yield an in situ AB monomer which was polymerized to yield a precursor polyhydrazide-amic-acid, which in turn was converted by cyclodehydration to an AB type polyoxadiazole-imide. Additional examples are cited of the formation of polymers from the in situ intermediates produced by the “self-regulating” reaction of aminobenzhydrazides with acid chlorides followed by polycondensation with difunctional monomers.     

New high temperature polymers. I. Wholly aromatic ordered copolyamides

Wholly aromatic ordered copolyamides of unusually high thermal stability were prepared by the condensation of aromatic diacid chlorides with symmetrical diamines containing preformed aromatic amide units in an ordered arrangement. The preservation of order in the condensation step was assured by using interfacial or solution polymerization techniques at temperatures below 50°C. Each polymer contains units derived from aminobenzoic acids, arylene diamines, and arylene diacids. By use of para- and meta- phenylene units, eight different polymers are possible; all were prepared. Differential thermal analyses and thermogravimetric analyses showed these polymers to have melting points or decomposition temperatures in a range from 410°C. for the all-meta polymer to 555°C. for the all-para one. Substitution of the internal N-hydrogens of the diamines with methyl groups or phenyl groups leads to additional ordered copolymers. Several were prepared, but their melting points were much lower than those of the parent polymers limiting their usefulness in high temperature applications. Tough pliable films were prepared from all eight unsubstituted polymers, and crystalline fibers with tenacities of ca. 6 g./den. were prepared from three of the polymers. The properties of the fibers were retained to a high degree even when determined at temperatures up to 400°C. Fibers aged at 300°C. for extended periods of time showed remarkable retention of fiber properties.     

Cyclopolycondensation. XIII. New synthetic route to fully aromatic poly(heterocyclic imides) with alternating repeating units

Fully aromatic poly(heterocyclic imides) of high molecular weight were prepared by the cyclopolycondensation reactions of aromatic diamines with new monomer adducts prepared by condensing orthodisubstituted aromatic diamines with chloroformyl phthalic anhydrides. The low-temperature solution polymerization techniques yielded tractable poly(amic acid), which was converted to poly(heterocyclic imides) by heat treatment to effect cyclodehydration at 250–400°C under reduced pressure. In this way, the polyaromatic imideheterocycles such as poly(benzoxazinone imides), poly(benzoxazole imides), poly(benzimidazole imides) and poly(benzothiazole imides) were prepared, which have excellent processability and thermal stability both in nitrogen and in air. The poly(amic acids) are soluble in such organic polar solvents as N,N-dimethyl-acetamide, N-methylpyrrolidone, and dimethyl sulfoxide, and the films can be cast from the polymer solution of poly(amic acids) (η_inh = 0.8–1.8). The film is made tough by being heated in nitrogen or under reduced pressure to effect cyclodehydration at 300–400°C. The polymerization was carried out by first isolating the monomer adducts, followed by polymerization with aromatic diamines. On subsequently being heated, the open-chain precursor, poly(amic acid), undergoes cyclodehydration along the polymer chain, giving the thermally stable ordered copolymers of the corresponding heterocyclic imide structure.     

Synthesis and properties of novel aromatic polyhydrazides and poly(amide–hydrazide)s based on the bis(ether benzoic acid)s from hydroquinone and substituted hydroquinones

4,4′‐(1,4‐Phenylenedioxy)dibenzoic acid as well as the 2‐methyl‐, 2‐tert‐butyl‐, or 2‐phenyl‐substituted derivatives of this dicarboxylic acid were synthesized in two main steps from p‐fluorobenzonitrile and hydroquinone or its methyl‐, tert‐butyl‐, or phenyl‐substituted derivatives. Polyhydrazides and poly(amide–hydrazide)s were prepared from these bis(ether benzoic acid)s or their diacyl chlorides with terephthalic dihydrazide, isophthalic dihydrazide, or p‐aminobenzoyl hydrazide by means of the phosphorylation reaction or low‐temperature solution polycondensation. Most of the hydrazide polymers and copolymers are amorphous and readily soluble in various polar solvents such as N‐methyl‐2‐pyrrolidone (NMP) and dimethyl sulfoxide. They could be solution‐cast into transparent, flexible, and tough films. These polyhydrazides and poly(amide–hydrazide)s had T_gs in the range of 167–237°C and could be thermally cyclodehydrated into the corresponding poly(1,3,4‐oxadiazole)s and poly(amide–1,3,4‐oxadiazole)s approximately in the region of 250–350°C, as evidenced by the DSC thermograms. All the tert‐butyl‐substituted oxadiazole polymers and those derived from isophthalic dihydrazide were organic soluble. The thermally converted oxadiazole polymers exhibited T_gs in the range of 208–243°C and did not show significant weight loss before 450°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1169–1181, 1999     

Self-regulating polycondensations: Ordered aromatic polyamide-esters

The polycondensation of aminophenols with diacid chlorides was examined to determine if the amide-ester polymers obtained are random or ordered. All of the evidence obtained points to the conclusion that ordered copolymers indeed are prepared and that a “self-regulating” polymerization process is operating by virtue of the considerably greater reactivity of aromatic amino groups relative to phenol groups. The first step of the reaction involves the in situ preparation of a diphenol-amide which undergoes further condensation. The diphenol-amide intermediate may be isolated or reacted in situ. In addition to the ordered polymer from a given aminophenol and a single diacid chloride, ordered copolymers from two different diacid chlorides were prepared in which the diacid moieties appear in an alternating fashion; the structure of such polymers depends on the order of addition of the diacid chlorides. Corresponding polymers also may be prepared from the preformed diphenol-amide monomers. The molecular weights of certain of the polymers were sufficient for the preparation of films which could be hot-stretched severalfold. Interfacial polycondensations gave polymers of higher inherent viscosities than did solution polymerizations when aminophenols or diphenol-amide monomers were condensed with diacid chlorides.     

Amide–quinoxaline copolymers

A series of new amide–quinoxaline ordered copolymers derived from phthaloyl, isophthaloyl, and terephthaloyl chlorides have been synthesized and characterized. The isophthaloyl and terephthaloyl polymers had decomposition temperatures between 445–495°C and were soluble in a variety of solvents. These high molecular weight polymers were prepared by reacting aromatic bis-o-diamines with bis(benzilyl)amides. Phthaloyl chloride yielded low molecular weight polymers due to competing side reactions.     

Soluble imide–quinoxaline copolymers

Eight new phenylated imide–quinoxaline ordered copolymers were prepared. The synthesis consisted of one-step solution condensations of aromatic bis(o-diamines) with N,N′-bis(benzilyl)benzophenoneimide and N,N′-bis(benzilyl)tetrahydrofuranimide respectively. The polymers were all of high molecular weight and were soluble in a number of different solvents. Thermal gravimetric analysis showed that the aromatic benzophenoneimide-quinoxalines (decomposing between 490 and 530°C) were considerably more stable than the aliphatic tetrahydrofuranimide–quinoxalines (decomposing between 290 and 320°C). All polymers gave tough films which could be cast from solution.     

Aromatic poly(1,3,4‐oxadiazole)s and poly(amide‐1,3,4‐oxadiazole)s containing ether sulfone linkages

Polyhydrazides and poly(amide‐hydrazide)s were prepared from two ether‐sulfone‐dicarboxylic acids, 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoic acid and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoic acid, or their diacyl chlorides with terephthalic dihydrazide, isophthalic dihydrazide, and p‐aminobenzhydrazide via a phosphorylation reaction or a low‐temperature solution polycondensation. All the hydrazide polymers were found to be amorphous according to X‐ray diffraction analysis. They were readily soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide and could afford colorless, flexible, and tough films with good mechanical strengths via solvent casting. These hydrazide polymers exhibited glass‐transition temperatures of 149–207 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the solid state at elevated temperatures. Although the oxadiazole polymers showed a significantly decreased solubility with respect to their hydrazide prepolymers, some oxadiazole polymers were still organosoluble. The thermally converted oxadiazole polymers had glass‐transition temperatures of 217–255 °C and softening temperatures of 215–268 °C and did not show significant weight loss before 400 °C in nitrogen or air. For a comparative study, related sulfonyl polymers without the ether groups were also synthesized from 4,4′‐sulfonyldibenzoic acid and the hydrazide monomers by the same synthetic routes. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2271–2286, 2001     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Aromatic polymers with side oxadiazole rings as luminescent materials in LEDs

Aromatic polyamides and polyazomethines with side oxadiazole rings have been synthesized by using aromatic diamines containing pendent substituted oxadiazole groups and a diacid chloride having diphenylsilane or hexafluoroisopropylidene, or an aromatic dialdehyde with fluorene unit, respectively. These polymers were easily soluble in amidic solvents. Very thin films which were deposited from polymer solutions onto silicon wafers exhibited smooth, pinhole-free surface in atomic force microscopy investigations. The polymers showed high thermal stability with decomposition temperature being above 400°C. Some of them exhibited blue photoluminescence, in the range of 450-480 nm, making them promising candidates for future use as high performance materials in the construction of light emitting devices.     

Synthesis and properties of wholly aromatic polymers bearing cardo fluorene moieties

Three series of aromatic polyamides, polyesters, and poly(1,3,4‐oxadiazole)s containing bulky fluorene structures were prepared from 9,9‐bis(4‐carboxyphenyl) fluorene. All of the polymers were readily soluble in many organic solvents and showed useful thermal stability associated with high glass‐transition temperatures in the range of 220–366 °C. These wholly aromatic polymer films were colorless, with high optical transparency, and exhibited UV‐vis absorption bands at 266–348 nm and photoluminescence maximum bands at 368–457 nm within the purple to green region in N,N‐dimethylacetamide (DMAc) solutions. The poly(amine‐amide) Ic exhibited excellent electrochromic contrast and coloration efficiency, changing color from the colorless neutral form to green and then to the dark blue oxidized forms with good stability of electrochromic characteristics. Almost all of these wholly aromatic polymer films were colorless and showed high optical transparency. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4352–4363, 2007     

Synthesis and optical properties of novel blue‐light‐emitting poly(p‐phenylene vinylene) derivatives with pendant oxadiazole or cyano groups

Two novel poly(p‐phenylene vinylene) polymers, which carried side substituents with cyano groups or 1,3,4‐oxadiazole, were synthesized by Heck coupling. They consisted of alternating conjugated segments and nonconjugated aliphatic spacers. The polymers had moderate molecular weights, were amorphous, and dissolved readily in tetrahydrofuran and halogenated organic solvents. They were stable up to approximately 340 °C in N₂ and 290 °C in air, and the anaerobic char yield was around 60% at 800 °C. The polymer with cyano side groups emitted blue light in solutions and thin films with identical photoluminescence (PL) maximum at 450 nm; this supported the idea that chain interactions were hindered even in the solid state. The PL maximum of this polymer in thin films was blueshifted upon annealing at 120 °C, indicating a thermochromic effect as a result of conformational changes in the polymer backbone. The polymer containing side substituents with oxadiazole rings emitted blue light in solutions with a PL maximum at 474 nm and blue‐greenish light in thin films with a PL maximum at 511 nm. The PL quantum yields of the polymers in tetrahydrofuran were 0.13–0.24. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1768–1778, 2004     

Benzheterocycle–imide and amide–imide fibers derived from diacid chlorides containing preformed imide groups

Fibers of benzoxazole–imide ordered copolymers were prepared by cyclodehydrating the amide–phenol units of precursor polyamide–o-hydroxyimide fibers at 375°C in nitrogen. The precursor polyamide–o-hydroxyimides were obtained by the reaction of 3,3′-dihydroxybenzidine with diacid chlorides containing preformed imide rings. The benzoxazole–imide fibers are very thermally stable, especially with respect to retention of tensile properties after heat aging in air. For example, the benzoxazole–imide fibers after heating aging in air for 35 days retained 75% or more of their original tenacities and 50% or more of their original elongations to break. The original fibers did not have high tenacities, probably because of the rather extreme thermal treatment required to cyclodehydrate the amide–phenol units of the precursor fiber. The ultraviolet light stability of one benzoxazole–imide fiber was outstanding for a fiber of the polyheterocycle type: there was no loss in strength or elongation after 140 hr of exposure in a Fade-Ometer. Fibers of ordered amide–imide polymers based on the same imide-containing diacid chlorides used for the benzoxazole–imide polymers were also prepared. They were substantially less thermally stable than their benzoxazole–imide fiber counterparts, as expected.     

Synthesis and optical properties of a poly(p‐phenylenevinylene) derivative and polyfluorenes with bipolar groups along the main chain

A poly(p‐phenylenevinylene) derivative (PPV–TPA)] and a series of statistical copolyfluorenes (PF–TPA)] containing oxadiazole and triphenylamine segments along the main chain were synthesized by the Heck reaction and nickel‐mediated coupling, respectively. The PF–TPA copolyfluorenes with relatively low contents of oxadiazole and triphenylamine units were readily soluble in common organic solvents, whereas the other copolyfluorenes displayed lower solubility. PPV–TPA showed excellent solubility in solvents such as tetrahydrofuran (THF), dichloromethane, chloroform, and toluene. Thin films of the polymers absorbed light in the range of 375–396 nm and had optical band gaps of 2.76–2.98 eV. They emitted blue‐green light with a maximum at 414–522 nm. The fluorescence quantum yields in THF solutions were 0.08–0.53. The copolyfluorene PF–TPA thin films with high contents of oxadiazole and triphenylamine moieties emitted pure blue light that remained stable even after annealing at 150 °C for 4 h in air. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3556–3566, 2006     

Synthesis,photophysics, structure‐tunable photoluminescence,and electrochemical properties of soluble poly(p‐phenylenevinylene)‐based polymers with adjacent 1,3,4‐oxadiazoles in the backbone

Three new poly(p‐phenylenevinylene)‐based polymers containing two 1,3,4‐oxadiazole moieties in the main chain per repeat unit were synthesized by Heck coupling. A single, double, or triple bond was introduced between the oxadiazoles to provide a means for modifying the polymer properties. The polymers were readily soluble in common organic solvents and showed T_g values lower than 50 °C. The color of the emissive light in both the solid state and the solution could be tuned by a change in the nature of the bond between the oxadiazole rings. The polymers emitted ultraviolet‐green light in solution with a photoluminescence (PL) emission maximum at 345–483 nm and blue‐green light at 458–542 nm in thin films. The PL quantum yields in solution were 0.36–0.43. The electrochemical properties are affected by the nature of the bond between the oxadiazoles as well. In polymers with a single bond between the oxadiazoles, a lower ionization potential was observed than in polymers with a double or triple bond. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3079–3090, 2005     

New poly(amide-imide)s syntheses. VII. Preparation and properties of poly(amide-imide)s derived from 1,5-bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

New bis(phenoxy)naphthalene-containing poly(amide-imide)s having an inherent viscosity in the range of 0.62–1.09 dL/g were prepared by the direct polycondensation of 1,5-bis(4-trimellitimidophenoxy) naphthalene ( I ) and various aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The diimide-diacid (I) was prepared by the condensation of 1,5-bis(4-aminophenoxy) naphthalene and trimellitic anhydride. Most of the polymers were soluble in aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc), and afforded transparent, flexible and tough films upon casting from DMAc solutions. Measurements of wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or oxyphenylene groups were characterized as crystalline polymers. Tensile strength and initial moduli of the polymer films ranged from 61–86 MPa and 1.83–2.21 GPa, respectively. Glass transition temperatures of the polymers were in the range of 231–340°C. The melting points of the crystalline polymers ranged from 375–430°C. The 10% weight loss temperatures were above 512°C in nitrogen and 481°C in air. © 1993 John Wiley & Sons, Inc.     

Synthesis and optical and electroluminescent properties of novel conjugated polyelectrolytes and their neutral precursors derived from fluorene and benzoselenadiazole

Novel copolymers derived from amino‐functionalized fluorene‐ and selenium‐containing heterocycles [2,1,3‐benzoselenadiazole (BSeD)] were synthesized by the palladium‐catalyzed Suzuki coupling method. Their quaternized salt polyelectrolytes of corresponding compositions were obtained by a postpolymerization treatment. The resulting copolymers were soluble in polar solvents. An efficient energy transfer due to exciton trapping on the BSeD sites was observed. Devices from such copolymers emitted orange‐red light peaked at 560–610 nm. All the polymers showed good device performance with high‐work‐function metal Al as a cathode without the use of an additional electron‐injection layer and are promising candidates for polymer light‐emitting diode applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2521–2532, 2006     

Polyimides having pendant hydroxy and acetoxy groups. I. Synthesis of polyimides from pyromellitimide and bisepoxides

Polyimides having pendant hydroxy groups were prepared by addition of pyromellitimide with bisepoxides. Tertiary amines and quaternary ammonium halides were effective as a catalyst. The polyimides were soluble in dichloroacetic acid and had inherent viscosities in the range 0.16–0.19 dl/g. Thermogravimetric analysis showed that a rapid weight loss of the polymers occurred at about 400°C. The pendant hydroxy groups were easily acetylated by treating the polymers with a mixture of acetic anhydride and pyridine. The acetylated polyimides were soluble in dimethylformamide, dimethylacetamide, and dioxane and melted at 120–150°C.     

Polyamides containing thiadiazole units: Synthesis and optical properties

Highly refractive and transparent polyamides containing thiadiazole units have been developed.These polymers were prepared by a polycondensation reaction of 4,4'-(1,3,4-thiadiazole-2,5-thio) bis(methylene) dibenzoyl chloride(TDTBM-DC) and diamine which contained thioether(―S―) and sulfone units.They showed good thermal stabilities such as a relatively high glass transition temperature of 206-233 °C and a 5% weight-loss temperature(T5%) of 376-395 °C.The optical transmittance of the polymer at 450 nm is higher than 83%.The heterocycle units and plural ―S― linkages provide the polymer with a high refractive index of 1.716-1.725 at 633 nm and a low birefringence of 0.003-0.004.Also they showed improved solubility in polar aprotic solvents and could form moderate strength films with tensile strength of 72.8-83.1 MPa and storage modulus of 1.0-1.8 GPa(at 200 °C).