铝基类水滑石和复合氧化物负载Pt催化剂的制备及对甲基苯酚加氢脱氧反应的催化性能

采用共沉淀法制备了多种铝基类水滑石,焙烧后得到对应的复合氧化物;以水滑石或复合氧化物为载体,制备了系列Pt基催化剂,研究了该催化剂对甲基苯酚加氢脱氧反应的催化性能。结果表明,Pt基催化剂的性能与载体的组分组成和结构相关;当以不经焙烧的类水滑石做载体时,所制备的Pt基催化剂具有较高的活性。其中,Pt-Ni-Al-H催化剂的加氢脱氧活性最高,对甲基苯酚转化率达到99.8%,甲苯选择性为1.4%,而Pt-Zn-Al-H催化剂的直接脱氧活性最高,在275℃和氢压2MPa下反应1h后,甲苯选择性达到84.1%。研究发现,反应过程中所生成的甲基环己烷可进一步发生脱氢反应转化为甲苯,说明所制备的Pt基催化剂具有较好的脱氢活性,可节省脱氧过程中的氢气消耗量。     

Adsorption of toluene, methylcyclohexane and neopentane on silica MCM-41

Adsorption-desorption isotherms of toluene, methylcyclohexane and neopentane were determined on a silica MCM-41 material of pore diameter ∼3.4 nm over the temperature range 258 K to 308 K (278 K for neopentane). The isosteric enthalpies of adsorption were determined from the isotherms at the various temperatures. It was found that the isotherms of toluene and methylcyclohexane have a similar variation with the temperature, exhibiting hysteresis at 268 K and at lower temperature, while the adsorption of neopentane is reversible at all temperatures. The three organic adsorptives interact differently with the silica surface and the isosteric enthalpies of adsorption indicated that methylcyclohexane has the weakest interaction and toluene the strongest. A slight increase in the adsorption enthalpy at the beginning of the capillary condensation step is observed with methylcyclohexane and neopentane but not with toluene.     

Volumetric Properties of Ternary-Pseudobinary Mixtures Containing Benzene and Cyclohexane

Densities have been measured as a function of composition for ternary-pseudobinary mixtures of [(benzene + toluene or methylcyclohexane) + (cyclohexane + toluene or methylcyclohexane)] by means of a vibrating-tube densimeter at atmospheric pressure and the temperature 298.15 K. The excess molar volumes, V_m^E, were calculated from the densities and correlated using the Redlich–Kister equation to estimate the coefficients and standard errors. The experimental and calculated quantities are used to discuss the mixing behavior of the components. The results show the third component, toluene and methylcyclohexane, influences the interaction between benzene and cyclohexane.     

Densities,refractive indices,and derived excess properties of the binary systems tert-butyl alcohol+toluene, +methylcyclohexane,and +isooctane and toluene+methylcyclohexane,and the ternary system tert-butyl alcohol+toluene+methylcyclohexane at 298.15 K

This paper reports experimental densities and refractive indices of the binary systems tert-butyl alcohol (TBA)+toluene, +isooctane, and +methylcyclohexane, and toluene+methylcyclohexane, and the ternary system TBA+toluene+methylcyclohexane, over the entire range of composition at 298.15 K. Excess molar volumes and changes of refractive indices were evaluated from the experimental data obtained. These derived properties were fitted to variable-degree polynomials. The experimental values of physical properties were compared with the values estimated by different methods of prediction.     

Liquid-liquid equilibria of (cyclohexane + acetonitrile + methylcyclohexane + toluene) and of {(acetonitrile + methylcyclohexane) + benzene or + toluene or + cyclohexane or + chlorobenzene} at 298.15 K

Tie-line results at 298.15 K and atmospheric pressure are reported for (cyclohexane + acetonitrile + methylcyclohexane + toluene) and for {(acetonitrile + methylcyclohexane) + benzene or + toluene or + cyclohexane or + chlorobenzene). The extended UNIQUAC and UNIQUAC equations are used to correlate binary vapour-liquid equilibria and mutual solubilities for 10 mixtures constituting the ternary mixtures and to predict the ternary and quaternary liquid-liquid equilibria by use of only binary parameters.     

Separation of Aromatics/Cyclic Aliphatics by Nonporous Adaptive Pillararene Crystals

The separation of cyclic aliphatics of high purity, which are produced from hydrogenation of the corresponding aromatics, is highly desired in the chemical industry. An energy‐efficient and environmentally friendly adsorptive separation method using nonporous adaptive crystals of perethylated pillar[5]arene (EtP5) and pillar[6]arene (EtP6) is described. Adaptive EtP5 crystals separate toluene from methylcyclohexane with 98.8 % purity, while adaptive EtP6 crystals separate methylcyclohexane from toluene with 99.2 % purity. The selectivities come from the stability of new EtP5 and EtP6 crystal structures upon capture of toluene and methylcyclohexane, respectively. The reversible transformations between nonporous guest‐free EtP5 or EtP6 structures and guest‐loaded structures make them highly recyclable.     

Partial hydrogenation of toluene over a ruthenium catalyst — A model treatment of a deactivation process

Hydrogenation of toluene to methylcyclohexene and methylcyclohexane was performed over a commercial 5% Ru/act. charcoal catalyst. The reaction was strongly affected by deactivation of the catalyst. The complete reaction model was examined together with a number of its simplified versions regarding their ability to fit experimental data. On the basis of the regression analysis results it was shown that methylcyclohexene could be thought as the main source of the strongly and irreversibly adsorbed surface deposits responsible for activity decrease of the catalyst. Direct transformation of toluene to methylcyclohexane was found to be insignificant. On the other hand substantial role of disproportionation of methylcyclohexene was proved.     

Synthesis of n-type perylene bisimide derivatives and their orthogonal self-assembly with p-type oligo(p-phenylene vinylene)s

Four different (chiral) electron-deficient (n-type) perylene bisimides containing aliphatic, aromatic, or ethyleneoxide side chaines have been synthesized and fully characterized. All of them form supramolecular stacks in apolar methylcyclohexane (MCH) solution as demonstrated by concentration- and temperature-dependent absorption, circular dichroism, and fluorescence studies. One derivative was investigated in more detail in the solid state and proven to be liquid crystalline and capable of forming nanometer-sized fiberlike networks when drop-cast from MCH. Optical spectroscopy techniques show that perylene bisimide and an oligo(p-phenylene vinylene) (p-type) derivative orthogonally self-assemble into separate nanosized p-and n-type stacks in MCH. In contrast in toluene only molecularly dissolved species are present. In films deposited from MCH as well as from toluene photoinduced electron transfer takes place from the p-type material to the n-type material. As a result of the orthogonal self-assembly process, in films from MCH an ordered network of fibers was formed, whereas in films from toluene no ordering was observed. However, probably due to the lateral orientation on the surface and the presence of long aliphatic chains pointing toward the electrodes, efficient bulk heterojunction solar cells could not be constructed.     

负载型Pt/CeO_2-Al_2O_3催化剂的制备及其脱氢性能

通过超声辅助共沉淀法制备了具有高比表面积、大孔容和大孔径的CeO_2-Al_2O_3复合载体,并以此制备了一系列负载型Pt/CeO_2-Al_2O_3催化剂,采用XRD、氮吸附、NH3-TPD、SEM和TEM等方法对复合载体和催化剂进行了表征;以甲基环己烷为模型化合物,考察了Pt/CeO_2-Al_2O_3催化剂的脱氢性能,研究了载体中Ce/Al物质的量比及反应温度对其催化脱氢性能的影响。结果表明,当Ce/Al物质的量比为0.5时,Pt/CeO_2-Al_2O_3催化剂在450℃下具有较高的脱氢性能;甲基环己烷转化率达到88.53%,甲苯的选择性达94.63%。     

Photoelectrochemical conversion of toluene to methylcyclohexane as an organic hydride by Cu2ZnSnS4-based photoelectrode assemblies

Direct photoelectrochemical conversion of toluene (TL) to methylcyclohexane (MC) with water has been examined as an organic hydride conversion using light irradiation. The production of MC from TL was observed on Pt/CdS/Cu(2)ZnSnS(4)/Mo photoelectrodes with anion-type ionomer membrane assemblies. A cathodic photocurrent was observed below 0.7 V vs RHE (V(RHE)) in 0.1 M Na(2)SO(4)/NaOH (pH 9.5) aqueous solution, and an apparent photocurrent density of 0.5 mA cm(-2) was obtained at 0 V(RHE) under the irradiation of a 300 W Xe lamp with a 420 nm cutoff filter. The yield of MC was measured by gas chromatography, and an 88% faradaic efficiency was estimated. This study suggests the possibility of direct energy conversion from solar energy to MC as an energy carrier of organic hydrides.     

The transformations of toluene on alumina and bifunctional catalysts

The activity of Pt, Rh, and Ni catalysts deposited on Al₂O₃ and tungsten-containing catalysts 20% H₄SiW₁₂O₄₀/ZrO₂ and 15% WO_x/ZrO₂ in the hydrogenation of toluene and toluene ring opening and isomerization in the presence of hydrogen was studied. Under experimental conditions (160–360°C, 2.2 MPa), the main reactions on Rh/Al₂O₃ were the hydrogenation of toluene into methylcyclohexane, hydrogenolysis into isoheptanes, and hydrocracking into alkanes C₁–C₆. On Pt, Rh, and Ni catalysts on carriers with strong acid properties, the isomerization of the six-membered into five-membered ring followed by hydrogenolysis (hydrocracking) of alkylcyclopentanes occurred. The yield of heptane isomers, however, did not exceed 13%. The activity of Pt and Rh catalysts on a high-acidity carrier (WO_x/ZrO₂) in hydrocracking was much higher than that of catalysts based on deposited heteropoly acid. The yields of hydrogenolysis (hydrocracking) products on Ni/WO_x/ZrO₂ were much lower than on Pt(Rh)/WO_x/ZrO₂. The highest yield of ring opening products (isoheptanes and n-heptane) was obtained with layered loading of two catalysts; it reached 58 wt % at 300°C and a 2.2 MPa pressure, which was 4.5 and 2 times higher than the yield obtained on Ni-Pt/WO_x/ZrO₂ and 2% Rh/Al₂O₃ catalysts. Hydrodemethylation was not the main direction of toluene transformations on any of the catalysts studied.     

Directed-sorting method for synthesis of bead-based combinatorial libraries of heterogeneous catalysts

The synthesis and analysis of inorganic material combinatorial libraries by a directed-sorting, split-pool bead method was demonstrated. Directed-sorting, split-pool, metal-loaded libraries were synthesized by adsorbing metal salts (H2PtCl6, SnCl2, CuCl2, and NiCl2) and metal standards (Pt, Cu, Ni in HCl) onto 2-mg porous gamma-alumina beads in 96- or 384-well plates. A matrix algorithm for the synthesis of bead libraries treated each bead as a member of a row or column of a given matrix. Computer simulations and manual tracking of the sorting process were used to assess library diversity. The bead compositions were analyzed by energy-dispersive X-ray spectroscopy, X-ray fluorescence spectroscopy, electron probe microanalysis, inductively coupled plasma atomic emission spectroscopy, and inductively coupled plasma mass spectroscopy. The metal-loaded beads were analyzed by laser-activated membrane introduction mass spectroscopy (LAMIMS) for catalytic activity using methylcyclohexane dehydrogenation to toluene as a probe reaction. The catalytic activity of individual beads that showed minimal (approximately 20% of that of Pt on alumina) to high conversion could be determined semiquantitatively by LAMIMS. This method, therefore, provides an alternative to screening using microreactors for reactors that employ catalysts in the form of beads. The directed-sorting method offers the potential for synthesis of focused libraries of inorganic materials through relatively simple benchtop split-pool chemistry.     

Determination of excess volumes in 1,2-dichloroethane + benzene, + toluene, + p-xylene, + cyclohexane,and + methylcyclohexane with a vibrating-tube densimeter

Densities of mixtures of 1,2-dichloroethane + benzene, + toluene, + p-xylene, + cyclohexane, and + methylcyclohexane were measured at 298.15 K over the whole concentration range by means of a vibrating-tube densimeter. Molar excess volumes were calculated from the results and compared to values obtained by interpolation or extrapolation of literature data.     

不同活性炭上Pt催化剂的分散性及其在甲基环己烷脱氢反应中的催化性能

在不同方法处理的活性炭上采用传统浸渍方法制备了负载Pt催化剂,并考察了其在甲基环己烷脱氢反应中的催化性能.对炭载体的氮吸附和程序升温脱附的表征结果表明,活性炭经过硝酸氧化处理和氢气高温处理后,活性炭的孔结构基本不变,但表面含氧官能团的数量和种类发生了变化.这些不同的表面基团直接影响了Pt粒子在载体上的分散度,进而使催化剂在反应中表现出不同的活性.     

Frequency response study of the dynamics of the platinum catalyzed interconversion of methylcyclohexane, toluene, and hydrogen near equilibrium

The dynamics of the platinum catalyzed interconversion of methylcyclohexane, toluene, and hydrogen near equilibrium were investigated in a closed reactor system by a frequency response method at temperatures in the range of 433 to 473 K and at total pressures in the vicinity of 80 to 110 Torr. The gas phase in contact with the platinum catalyst was always hydrogen-rich, with hydrogen to hydrocarbon mole ratios maintained in the range of 3.2 to 4.6. The frequency response method utilized small perturbations (lower than 1%) of the volume of the system, with measurements of the total pressure being used to determine the response of the system. The range of perturbation frequencies investigated was approximately 0.002 to 3 Hz (0.013 to 19 rad s(-1)). The experiments revealed two characteristic relaxation frequencies that are associated with the dynamics of the interconversion. The dynamics of the system are interpreted in terms of a simple two-step interconversion sequence with the aid of a phenomenological frequency response theory formulated in terms of relaxation frequencies of the steps and equilibrium properties of the system. It is concluded that one of the steps, a toluene adsorption-desorption step, is much slower than the other, a step involving the interconversion of the gas-phase methylcyclohexane and chemisorbed toluene that releases or consumes hydrogen in the process.     

Electrode independent chemoresistive response for cobalt phthalocyanine in the space charge limited conductivity regime

The electrical properties of 50 nm thick metallophthalocyanine films, prepared by organic molecular beam epitaxy (OMBE) on interdigitated electrodes, were studied with DC current-voltage measurements and impedance spectroscopy. The transition from Ohmic behavior at low voltages to space-charge-limited conductivity (SCLC) at higher voltages depends on the metal electrode (Pt, Pd, and Au), but does not correlate with the work function of the electrode. Impedance spectroscopy studies show the coexistence of low- and high-frequency traps in the thin film devices, and the contribution of low-frequency traps associated with Ohmic behavior diminishes at higher bias. Although device resistances are strongly influenced by the electrode material, and vary by a factor of over 300, the relative chemical sensor responses on exposure to dimethyl methylphosphonate (DMMP), methanol, water, or toluene vapors are similar for CoPc on Pt, Pd, and Au electrodes when these devices are operated in the SCLC regime at room temperature. When the devices are operated at voltages where the low-frequency interfacial traps are filled, the sensor response to analyte becomes uniform and reliable regardless of the specific interfacial electrode contact.     

Characterization of Pt nanoparticles deposited onto carbon nanotubes grown on carbon paper and evaluation of this electrode for the reduction of oxygen

Multiwalled carbon nanotubes (MWCNTs) were grown on the fibers of a commercial porous carbon paper used as carbon-collecting electrodes in fuel cells. The tubes were then covered with Pt nanoparticles in order to test these gas diffusion electrodes (GDEs) for oxygen reduction in H2SO4 solution and in H2/O2 fuel cells. The Pt nanoparticles were characterized by cyclic voltammetry, transmission electron microscopy, and X-ray photoelectron spectroscopy. The majority of the Pt particles are 3 nm in size with a mean size of 4.1 nm. They have an electrochemically active surface area of 60 m2/g Pt for Pt loadings of 0.1-0.45 mg Pt/cm2. Although the electroactive Pt surface area is larger for commercial electrodes of similar loadings, Pt/MWCNT electrodes largely outperform the commercial electrode for the oxygen reduction reaction in GDE experiments using H2SO4 at pH 1. On the other hand, when the same electrodes are used as the cathode in a H2/O2 fuel cell, they perform only slightly better than the commercial electrodes in the potential range going from approximately 0.9 to approximately 0.7 V and have a lower performance at lower voltages.     

Excess molar enthalpies of binary mixtures of 1-hexene with some cyclic and aromatic hydrocarbons at 298.15 K

Microcalorimetric measurements of excess molar enthalpies, at 298.15 K, are reported for the four binary systems formed by mixing 1-hexene with the cycloalkanes: cyclohexane and methylcyclohexane, and with the aromatic hydrocarcons: benzene and toluene. Smooth Redlich-Kister representations of the results are presented. It was found that the Liebermann-Fried model also provided good representations of the results.     

Solubility and Flory Huggins parameters of SBES, poly(styrene-b-butene/ethylene-b-styrene) triblock copolymer, determined by intrinsic viscosity

Solubility parameter and Flory Huggins interaction parameter of a triblock SBES have been obtained from intrinsic viscosity measurements. The solubility of the block copolymer in all solvents (methyl-cyclohexane, cyclohexane, cyclopentane, toluene and benzene) was found good except in the case of n-hexane. The results obtained are similar to other found in literature for SBR and SBS rubbers, and indicate that cyclohexane and cyclopentane and methylcyclohexane are the most compatible solvents for this kind of polymer.     

Electrodeposited Pt and Pt-Sn nanoparticles on Ti as anodes for direct methanol fuel cells

Electro-oxidation of methanol was studied on titanium supported nanocrystallite Pt and Pt_x-Sn_y catalysts prepared by electrodeposition techniques. Their electro-catalytic activities were studied in 0.5mol/L H₂SO₄ and compared to those of a smooth Pt, Pt/Pt and Pt-Sn/Pt electrodes. Platinum was deposited on Ti by galvanostatic and potentiostatic techniques. X-ray diffractometer (XRD) and energy dispersive X-ray (EDX) techniques were applied in order to investigate the chemical composition and the phase structure of the modified electrodes. Scanning electron microscopy (SEM) was used to characterize the surface morphology and to correlate the results obtained from the two electrochemical deposition methods. Results show that modified Pt/Ti electrodes prepared by the two methods have comparable performance and enhanced catalytic activity towards methanol electro-oxidation compared to Pt/Pt and smooth Pt electrodes. Steady state Tafel plots experiments show a higher rate of methanol oxidation on a Pt/Ti catalyst than that on a smooth Pt.  Introduction of a small amount of Sn deposited with Pt improves the catalytic activity and the stability of prepared electrode with time as indicated from the cyclic votlammetry and the chronoamperometric experiments. The effect of variations in the composition for binary catalysts of the type Pt_x-Sn_y/Ti towards the methanol oxidation reaction is reported. Consequently, the Pt_x-Sn_y/Ti (x∶y (8∶1), molar ratio) catalyst is a very promising one for methanol oxidation.