Electrochemical investigation of corrosion and corrosion inhibition of iron in hydrochloric acid solutions

The inhibition effect of 1-methyl pyrazole (MPA) on the acidic corrosion of iron in 1.0 M HCl was studied at different concentrations (10^?3–10^?2 M) by potentiodynamic polarization and electrochemical impedance spectroscopy, and EIS measurements. It is found from the polarization studies that methyl pyrazole (MPA) behaves mainly as anodic inhibitor in HCl. Values of polarization resistance (R_p) and double layer capacitance (C_dl) in the absence and presence of MPA in 1.0 M HCl are determined. The adsorption of MPA on iron surface from HCl is found to obey Temkin adsorption isotherm.     

Inhibitors for magnesium corrosion: Metal organic frameworks

Electrochemical measurements demonstrate that magnesium surfaces can be protected by alkyl carboxylate. In a nearly neutral pH solution of sodium decanoate, the reduced corrosion rate and a passivation behaviour are attributed to the formation of Mg(C₁₀H₁₉O₂)₂(H₂O)₃ (Mg(C10)₂) at the magnesium surface whereas heptanoate Mg(C₇H₁₃O₂)₂(H₂O)₃ (Mg(C7)₂) is not efficient in such media. The crystal structures of the two metal carboxylates Mg(C7)₂ and Mg(C10)₂ are determined by X-ray diffraction. Single crystal data: Mg(C7)₂, P2₁/a, a = 9.130(5) Å, b = 8.152(5) Å, c = 24.195(5) Å, β = 91.476(5)°, V = 1800.3(15) Å³, D_x = 1.242 g cm⁻³, Z = 4. Synchrotron powder data: Mg(C10)₂, P2₁/a, a = 9.070(3) Å, b = 8.165(1) Å, c = 32.124(1) Å, β = 98.39(1)°, V = 2353.85(8) Å³, D_x = 1.188 g cm⁻³, Z = 4. Their layered structures are quite similar and differ mainly by the length of the hydrophobic chains. They consist of two planes of O-octahedra centred by Mg atoms, parallel to (001). The distorted octahedra are constituted by three oxygen atoms from carboxylate groups and by three oxygen atoms coming from water molecules. The layers are connected by hydrogen bonds. The carboxylate chains are located perpendicularly and on both sides of these planes. One carboxylate chain is bridging the Mg atom along [010] while the other is monodendate. The presence of structural water is confirmed by thermal analyses.     

Poisoning the corrosion of magnesium

Despite possessing excellent specific properties, rapid corrosion of magnesium is a significant barrier in its widespread use. Alloying Mg to enhance mechanical properties nominally increases susceptibility to corrosion from microstructural heterogeneity. Furthermore, alloying Mg nominally accelerates cathodic kinetics and hence also accelerates corrosion. To date, no alloying additions to Mg suggest that a reduction in corrosion rate can be imparted, however we reveal for the first time that alloying additions of arsenic can impart significant corrosion resistance to Mg via retarding the cathodic reaction.     

Corrosion and corrosion inhibition characteristics of bulk nanocrystalline ingot iron in sulphuric acid

The corrosion and corrosion inhibition of bulk nanocrystalline ingot iron (BNII) fabricated from conventional polycrystalline ingot iron (CPII) by severe rolling was studied in 0.5 M H₂SO₄ solution using electrochemical impedance spectroscopy and potentiodynamic polarization techniques. The results indicate that BNII was more susceptible to corrosion in the acidic environment essentially because of an increase in the kinetics of the anodic reaction. An amino acid cysteine (cys) was employed as a corrosion inhibitor at concentrations of 0.001 and 0.005 M. Tests in inhibited solutions revealed that cys reduced the corrosion rates of both metal specimens by different mechanisms. For CPII cys inhibited the cathodic reaction but had a stimulating effect on the anodic process at low concentration and a trivial effect at higher concentration. For BNII, cys inhibited both the cathodic and the anodic reactions, although the former effect was more pronounced. Iodide ions improved the inhibitive effect of cys without altering the inhibition mechanism.     

A new bipyrazolic compound as corrosion inhibitor of armco iron in 1M HCl medium

The inhibitory effect of the new synthesized bipyrazolic compound 1,3-Bis(3,5-dichloromethylpyrazolyl) propane (BDCMPP) on the corrosion of Armco Iron in 1M HCl medium has been studied by weight loss, electrochemical polarisation and impedance studies. The maximum inhibition efficiency reached was about 90% at 10⁻³M. The inhibition effect is caused by geometrically blocking the surface of iron by adsorbed inhibitive molecules which follow an S-shaped adsorption isotherm.     

HyperLab: A new concept in gamma-ray spectrum analysis

HyperLab is a new Ge gamma-ray analysis code for MS Windows, developed using object-oriented design. The novel feature of the program is the extensive use of relational database technology, which allows the efficient storage and handling of any digital data encountered in gamma-ray spectroscopy. While preserving the main concept of the predecessors (HYPERMET and its derivatives) for semi-automatic analysis of multichannel pulse-height spectra, the substantially reshaped basic routines vastly improved the stability and reliability of peak fitting. New features include the fitting of peaks with high energy tail, as well as library-directed Graphical Isotope Identification. Procedures for efficiency, nonlinearity, etc. calibrations are now highly automated. By exploiting all the benefits of MS Windows technology (point-and-click simplicity in task executions, intelligent mouse pointer, etc.) HyperLab is a versatile and user-friendly tool which the discriminating spectroscopist will find of great value.     

O-alkenyl hydroxylamines: a new concept for cyclofunctionalization

[reaction: see text] Treatment of O-homoallylhydroxylamines with palladium(II) and copper(II) in the presence of a base, methanol, and carbon monoxide results in the formation of isooxazolidines. An electron-withdrawing group on the hydroxylamine nitrogen is essential. When carbamate groups are used the products are formed exclusively as their cis isomers.     

A new two-chip concept for continuous measurements on PMMA-microchips

A new concept for continuous measurements on microchips is presented. A PMMA (polymethylmethacrylate) based capillary electrophoresis chip with integrated conductivity detection is combined with a second chip, which undertakes the task of fluid handling and electrical connections. The combination of electrokinetic and hydrodynamic flows allows long-term continuous stable analyses with good reproducibilities of migration time and peak heights of analytes. The two-chip system is characterized in terms of stability and reproducibility of separation and detection of small ions. Relative standard deviations of <1% and 3% respectively for retention times and peak heights during long-term measurements can be achieved. The new system combines simple handling and automated analysis without the need for refilling, cleaning or removal of the separation chip after one or several measurements.     

Secondary doping: A new concept in conducting polymers

Phenomenologically, a primary dopant for a conducting polymer is a substance which drastically changes the electronic, optical, magnetic, and/or structural properties of the polymer and is accompanied by a large increase in conductivity. Phenomenologically, a secondary dopant is an apparently “inert” substance which, when applied to a primary-doped polymer, induces still further changes in the above properties including a further increase in conductivity. The concept of secondary doping will be illustrated using polyaniline and its derivatives.     

A new data management concept for AES and SAM

The problem of interchangeability of surface analytical data is gaining increasing importance in multi-method surface analysis. There are various surface analytical instruments in different laboratories on several automation levels. For these instruments, which are controlled by computer systems working with company-specific software under various operating systems, a standardised data format is necessary to allow an exchange of data. Therefore, we are developing a software package for the transfer, archiving and editing of surface analytical data called MAXMIND (management and exchange of method independent data), which is based on public domain software products. It allows the storage of all available and necessary information on experimental conditions and all parameters specific for a number of analytical techniques such as AES, SAM, XPS, SIMS, STM and AFM. Additionally, all data concerning the sample-preparation and the state of the instrument are included in order to allow a well-founded evaluation of the data and improved reproducibility of the experiment. This concept is demonstrated in detail for the two Auger techniques AES (Auger Electron Spectroscopy) and SAM (Scanning Auger Microscopy).Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

On the corrosion inhibition of iron in hydrochloric acid solutions,Part I: Electrochemical DC and AC studies

The inhibitive action of 4-methyl pyrazole (4MP) against the corrosion of iron (99.9999%) in solutions of hydrochloric acid has been studied using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). At inhibitor concentration range (10^?3–10^?2 M) in 1.0 M acid, the results showed that 4MP suppressed mainly the anodic processes of iron corrosion in 1.0 M HCl by adsorption on the iron surface according to Temkin adsorption isotherm. Both potentiodynamic and EIS measurements reveal that 4MP inhibits the iron corrosion in 1.0 M HCl and that the efficiency increases with increasing inhibitor concentration. Data obtained from EIS were analyzed to model the corrosion inhibition process through an equivalent circuit.     

Phosphatation of iron powder metallurgical samples for corrosion protection

Recently, powder metallurgy methods have been used widely for industrial purposes. In this work, powder-metallurgically produced samples were selected for zinc phosphate coating. Zinc phosphate coating was performed at 50 and 70 °C for 20 min in a bath containing 10 g l^?1 ZnO, 25.5 g l^?1 H₃PO₄, 5.88 g l^?1 HNO₃, and 2 g l^?1 NaNO₃. The effect of temperature on the phosphating process has been studied. The structure and corrosion resistance of coats have been investigated using scanning electron microscopy (SEM) and electrochemical methods (polarization and EIS). Results show that an increase in temperature affects the crystalline structure of the coats. The formation of the zinc phosphate coat on the powder metallurgical samples significantly decreases the corrosion rate of the samples.     

A study of corrosion on a rotating iron disk electrode

Corrosion of iron in slightly acidified sodium sulphate solutions (mainly pH 4.5) in the open air was studied with a rotating disk electrode method at room temperature.Microscopic observations of corroded iron disk surfaces in the pH 4.5 solution revealed that iron initially corrodes locally with the formation of round pits of 10–30 μm in diameter and of(0.6–1.3) × 10³ in number per apparent square centimetre followed by the U-shaped brown protective wall formation of precipitates (rust) outside the pits. Each protective wall is formed along the lines of flow of the solution adjacent to the iron surface and each pit is located near the upstream end of the wall. Steady state of corrosion sets in when the parts of surface area surrounded by the wall are completely covered with a microscopically non-porous rust film.The amount of iron in the rust film and the total amount of corrosion of iron including that in the film increase parabolically with the increase in the time of immersion. The amount of iron in the film increases in proportion to the total amount of corrosion independently of the speed of rotation of the disk electrode even in the steady state.The fraction of area of iron surface not covered with the film decreases with time and reaches a certain fixed value in the steady state: the value is smaller at higher rotational speed. The corrosion rate is proportional to the uncovered area, as the corrosion is near the steady state. The pH of the bulk solution increases as corrosion progresses.The corrosion rate of iron can be well interpreted by assuming that the rate is controlled by the diffusion of oxygen from the bulk solution to the surface of iron and that the rust film on iron impedes the diffusion of oxygen.     

A new concept in friction testing

Methods of measuring friction are reviewed and their shortcomings discussed. The advantages of using the wide range of test speeds, environmental conditions and recording facilities available on a tensile test machine are indicated and a new apparatus designed to fit a tensile tester is described. The design concepts are outlined in some detail and the factors limiting stick-slip motion are indicated. The apparatus can be used either for studies of materials or as an aid to product selection. Test results on a polyurethane rubber, covering a range of velocities and temperatures, illustrate the former, and tests on windscreen wiper blades under both wet and dry conditions illustrate the latter. Although primarily designed for testing the friction of polymers the apparatus is of universal application and can be used for measuring, against a chosen substrate, the coefficients of friction of metals, fabrics, paper, glass, leather, or any other material capable of being mounted in a vertical plane. It is not suitable for particulate matter such as sand, but could be used, for example, for studying the effect of floor finishes on a range of flooring materials.     

Enantioselective Alternating Olefin-Carbon Monoxide Copolymerization: A new concept for activity and stereoselectivity

Cationic Pd-complexes modified by dicyclohexyl{(R)-1-[(S)-2-(diphenylphosphino)ferrocenyl]ethyl}phosphine ( 1a ) give very active catalytic systems for the regioregular isotactic specific copolymerization of propene with CO. Other alk-1-enes also give stereoregular and regioregular copolymers, even if with lower productivity. The copolymers are isolated as poly(4-alkyl-tetrahydrofuran-2,2,5,5-tetrayl-2-oxy-2-methylenes) B in the solid state and give the isomeric poly(2-alkyl-1-oxopropane-1,3-diyls) A by dissolution in (CF₃)₂CHOH. Solid polymer A (R = Et) is formed back at least partially when the dissolved material is reprecipitated from MeOH. The use of the related (ferrocenyl)diphosphine ligands 1b ? e and 2 as the catalyst modifier shows that the presence of both elements of chirality and of large substituents on the P-atoms of the ligand is necessary to achieve good stereocontrol, and that the large difference in basicity between the two P-atoms is probably the reason for the good catalytic activity.     

A new reagent for the spectrophotometric determination of magnesium (II): Khimduchlorophosphonazo-I

Summary The colour reaction of magnesium(II) with Khimduchlorophosphonazo-I (KCPA-I) has been studied spectrophotometrically with a view to develop a procedure for the determination of exchangeable magnesium in acidic soils.The optimum acidities are pH 8.78–9.90. The absorption maximum and molar absorptivity of the coloured complex are 580 nm and 1.85 · 10⁴ l · mol^–1 · cm^–1, respectively. The colour intensity is stable for 4 h and is found to obey Beer's law within the concentration range of 0–20 g per 25 ml. The method is simple and reliable (standard deviation 0.8–1.2%). It has been applied to the determination of exchangeable magnesium.

---

Neues Reagens für die spektralphotometrische Bestimmung von Magnesium (II): Khimduchlorophosphonazo-I

Zusammenfassung Die Farbreaktion von Magnesium mit Khimduchlorophosphonazo-I wurde im Hinblick auf die Entwicklung eines entsprechenden Analysenverfahrens untersucht. Der optimale pH-Wert liegt im Bereich von 8,78–9,90. Das Absorptionsmaximum liegt bei 580 nm, der molare Extinktionskoeffizient beträgt 1,85 · 10⁴l · mol^–1 · cm^–1. Die Färbung bleibt 4 h lang stabil und befolgt das Beersche Gesetz von 0 bis 20 g/25 ml. Das Verfahren ist einfach und zuverlässig (Standardabweichung 0,8–1,2%) und wurde zur Bestimmung von austauschbarem Magnesium in sauren Böden angewendet.

     

A new model for magnesium chemistry in the upper atmosphere

This paper describes the kinetic study of a number of gas-phase reactions involving neutral Mg-containing species, which are important for the chemistry of meteor-ablated magnesium in the upper mesosphere/lower thermosphere region. The study is motivated by the very recent observation of the global atomic Mg layer around 90 km, using satellite-born UV-visible spectroscopy. In the laboratory, Mg atoms were produced thermally in the upstream section of a fast flow tube and then converted to the molecular species MgO, MgO(2), OMgO(2), and MgCO(3) by the addition of appropriate reagents. Atomic O was added further downstream, and Mg was detected at the downstream end of the flow tube by laser-induced fluorescence. The following rate coefficients were determined at 300 K: k(MgO + O → Mg + O(2)) = (6.2 ± 1.1) × 10(-10); k(MgO(2) + O → MgO + O(2)) = (8.4 ± 2.8) × 10(-11); k(MgCO(3) + O → MgO(2) + CO(2)) ≥ 4.9 × 10(-12); and k(MgO + CO → Mg + CO(2)) = (1.1 ± 0.3) × 10(-11) cm(3) molecule(-1) s(-1). Electronic structure calculations of the relevant potential energy surfaces combined with RRKM theory were performed to interpret the experimental results and also to explore the likely reaction pathways that convert MgCO(3) and OMgO(2) into long-lived reservoir species such as Mg(OH)(2). Although no reaction was observed in the laboratory between OMgO(2) and O, this is most likely due to the rapid recombination of O(2) with the product MgO(2) to form the relatively stable O(2)MgO(2). Indeed, one significant finding is the role of O(2) in the mesosphere, where it initiates holding cycles by recombining with radical species such as MgO(2) and MgOH. A new atmospheric model was then constructed which combines these results together with recent work on magnesium ion-molecule chemistry. The model is able to reproduce satisfactorily some of the key features of the Mg and Mg(+) layers, including the heights of the layers, the seasonal variations of their column abundances, and the unusually large Mg(+)/Mg ratio.     

A new layered iron fluorophosphate

A new iron fluorophosphate of the composition, [C₆N₄H₂₁] [Fe₂F₂(HPO₄)₃][H₂PO₄]·2H₂O,I has been prepared by the hydrothermal route. This compound contains iron fluorophosphate layers and the H₂PO₄ ^- anions are present in the interlayer space along with the protonated amine and water molecules. The compound crystallizes in the monoclinic space group P2₁/c.(a = 13.4422(10) ?,b = 9.7320(10) ?, c = 18.3123(3) ?, β= 92.1480°,V= 2393.92(5) ?³, Z = 4,M = 719.92,d _calc. = 1.997 g cm^-3, R₁ = 0.03 andwR ₂= 0.09).     

Amine–quinone polyimide: A new high‐temperature polymer and its use to protect iron against corrosion

A new diamine monomer was synthesized by the Michael addition of 4,4′‐methylene dianiline with 1,4‐benzoquinone. The monomer was condensed with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride to give a polyamic acid that was soluble in NMP. The polyamic acid was cast onto iron and thermally imidized to yield the amine–quinone polyimide (AQPI‐2). AQPI‐2 had a thermal decomposition temperature of 540 °C (10% TGA weight loss in N₂) and a glass transition at 292 °C, values typical of polyimides. The degradation of the coating on iron after exposure to 0.1 M NaCl electrolyte was followed by electrochemical impedance spectroscopy. Under these conditions a conventional polyimide failed after 3 days exposure, while AQPI‐2 survived more than 24 days exposure. The adhesive bond between the amine–quinone polyimide and the iron surface was so strong that it could not be broken by the electrolyte. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2893–2899, 2000