气相色谱-质谱法测定玩具中邻苯二甲酸酯类增塑剂

采用二氯甲烷作为萃取溶剂,超声提取塑料玩具和毛绒玩具中的6种增塑剂,提出了邻苯二甲酸二正丁酯(DBP)、邻苯二甲酸(2-乙基己基)酯(DEHP)、邻苯二甲酸二异壬酯(DINP)、邻苯二甲酸丁苄酯(BBP)、邻苯二甲酸二正辛酯(DNOP)和邻苯二甲酸二异癸酯(DIDP)等6种增塑剂的气相色谱-质谱分析方法。在选定的试验条件下,BBP、DBP、DEHP和DNOP可以完全分离,通过比较保留时间、色谱图和峰面积(m/z 149),可实现以上4种物质的定性和定量分析。而DIDP和DINP的峰重叠,需通过选择m/z293,307质谱峰进行定量分析。结果表明方法能够有效地检测出玩具中邻苯二甲酸酯类增塑剂的含量。     

HPLC测定一次性塑料用品中邻苯二甲酸酯类增塑剂

本文用高压、液体色谱柱Liehmspher C-18(250mm×4.6mmID,5μm),以乙腈-水为流动相,流速为1.0mL/min,线性梯度乙腈从70%到100%,采用质谱检测器对邻苯二甲酸酯进行定性鉴定.邻苯二甲酸二甲脂(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二甲酸辛酯(DOP)浓度分别为1.1～89mg/L,0.9～74mg/L,0.9～71mg/L和0.9～68mg/L时线性关系良好,平均回收率分别为83%,89%,86%,87%(n=5).建立了准确度和灵敏度高,方便快捷有效的一次性塑料用品中邻苯二甲酸酯类增塑剂的高效液相色谱定量分析方法.     

常见食品中邻苯二甲酸酯类增塑剂含量及食品包装材料中邻苯二甲酸酯类增塑剂迁移量的测定

采用气相色谱-质谱联用(GC-MS)方法并结合液液萃取及基质分散固相萃取的样品处理方式,建立了测定饮料、牛奶、白酒3类食品中16种邻苯二甲酸酯类增塑剂的分析方法。研究结果表明16种邻苯二甲酸酯类增塑剂的检出限(LOD, S/N=3)范围为0.005~0.025 mg/L;峰面积的相对标准偏差(RSD)均小于2%。饮料、牛奶、白酒3种样品的加标回收率范围普遍在60%~110%。所建方法简便、灵敏、准确,可满足饮料、牛奶和白酒中痕量邻苯二甲酸酯类增塑剂的测定需要。此外,将该方法应用于食品包装材料中邻苯二甲酸酯类增塑剂的迁移研究,以异辛烷为油脂食品模拟物,测定了保鲜膜与保鲜袋中16种邻苯二甲酸酯类增塑剂的迁移量。结果显示保鲜膜存在显著的邻苯二甲酸酯类增塑剂迁移现象。     

傅立叶变换红外光谱法对聚氯乙烯及邻苯二甲酸酯类增塑剂的快速鉴定

应用傅立叶变换红外光谱法实现了聚氯乙烯及邻苯二甲酸酯类增塑剂的快速鉴别。对聚氯乙烯的定性采用了衰减全反射技术,用锗作为晶体材料,对邻苯二甲酸酯类的定性则采用透射法。用溶解-沉淀法对试样进行分离和纯化,所用溶剂为四氢呋喃,沉淀剂为无水乙醇。经过此方法,聚合物与增塑剂达到很好的分离和纯化。     

超临界流体色谱同时测定运动饮料中的8种邻苯二甲酸酯类增塑剂

建立了同时快速测定运动饮料中邻苯二甲酸二甲酯、邻苯二甲酸二乙酯、邻苯二甲酸二丙酯、邻苯二甲酸二丁酯、邻苯二甲酸二戊酯、邻苯二甲酸丁基苄基酯、邻苯二甲酸二（2-乙基己基）酯、邻苯二甲酸二辛酯8种邻苯二甲酸酯（PAEs）类增塑剂的超临界流体色谱-紫外检测分析方法。实际样品经液相萃取后,用超临界流体色谱分析,以超临界态二氧化碳-3%（体积分数）甲醇作为色谱流动相进行等度洗脱,检测波长为225 nm,6 min即可实现分离。8种PAE类增塑剂在0.05~25 mg/L范围内均具有良好的线性关系,相关系数为0.9991~0.9997,方法检出限为7.5~15 μg/L。8种PAE类增塑剂在运动饮料样品中的加标回收率为91.7%~100.2%,相对标准偏差均不大于6.5%（n=3）。应用该方法对多种市售运动饮料中的8种PAE类增塑剂进行检测,结果表明,该方法环保、快速、灵敏、选择性高、结果准确,能满足运动饮料中增塑剂含量检测的要求。     

凝胶渗透色谱净化-高效液相色谱法测定油脂食品中的邻苯二甲酸酯类增塑剂

建立了油脂食品(方便面、油炸糕点、沙琪玛、食用油等)中5种主要邻苯二甲酸酯类增塑剂的凝胶渗透色谱（GPC）净化-高效液相色谱(HPLC)分析方法。食品样品用石油醚超声提取,经GPC净化后,采用反相HPLC进行分析。所用的分离柱为Labtech C18(250 mm×4.6 mm, 5 μm),以乙腈和水为流动相,梯度洗脱。方法的相关系数皆在0.997以上,目标物的检出限(信噪比为3计)为3.25～13.4 μg/L。在50 mg/L添加水平时,目标物的加标回收率为70.4%～113.6%,相对标准偏差为0.3%～5.8%(n=3)。该方法简便、快捷、实用,可用于油脂食品中邻苯二甲酸酯类增塑剂的分析测定。     

气相色谱-质谱法测定橡皮擦中五种邻苯二甲酸酯增塑剂含量

本文建立了一种橡皮擦中5种邻苯二甲酸酯增塑剂的气相色谱-质谱检测方法。采用乙酸乙酯加热搅拌的方法提取目标物,选择离子模式检测,外标法定量。优化的前处理和测定条件下,5种目标物的平均回收率为81.18%~117.92%,相对标准偏差在1.14%~5.57%之间。通过该方法对国内市场上8种橡皮擦样品进行检测,结果5种样品检出邻苯二甲酸二(2-乙基)己酯,含量超过0.1%。     

超声提取-气相色谱-质谱法测定塑料包装食品中16种邻苯二甲酸酯类增塑剂

建立超声提取–气相色谱–质谱法同时测定塑料包装食品中16种邻苯二甲酸酯类增塑剂的残留量。以甲醇为萃取溶剂,采用超声萃取法进行样品处理,超声提取时间为30 min,超声提取温度为50℃。16种邻苯二甲酸酯类物质的质量浓度在0.1～50 mg/L范围内与峰面积具有良好的线性关系,线性相关系数均大于0.99,方法检出限为0.05 mg/L。样品的加标回收率为83.4%～97.0%,测定结果的相对标准偏差为1.91%～4.64%(n=6)。该方法简单、灵敏且准确,适用于塑料包装食品中16种邻苯二甲酸酯类增塑剂残留量的测定。     

三重串联四级杆气质联用法测定化妆品中的三种邻苯二甲酸酯类增塑剂

建立了一种快速、灵敏、准确的三重串联四级杆气质联用(GC-MS/MS)法,将其用于同时检测化妆品中的三种邻苯二甲酸酯(邻苯二甲酸二丁酯、邻苯二甲酸丁基苄基酯、邻苯二甲酸二乙基己酯)增塑剂.化妆品经甲醇提取,HP-5MS柱分离,采用GC-MS/MS的多反应监测模式,以保留时间和离子对(母离子和子离子)信息比较定性,以母离子和响应值高的子离子进行定量.结果表明,该方法的检出限为12～28ng/g,相对标准偏差为1.6%～7.54%,目标物的加标回收率为86.4%～121.1%;该方法可用于检测日常化妆品中邻苯二甲酸酯的含量.     

超声萃取/气相色谱-串联质谱法同时测定皮革制品中20种邻苯二甲酸酯类增塑剂

建立了同时测定皮革制品中20种邻苯二甲酸酯类增塑剂的气相色谱-串联质谱方法。该方法以正己烷为提取溶剂,室温下超声提取皮革制品中的邻苯二甲酸酯类增塑剂,提取液经中性氧化铝固相萃取柱净化后进行气相色谱-串联质谱分析。该方法简便快速,定性定量准确,灵敏度高,DIDP、DINP和DMPP的定量下限(S/N=10)分别为0.2、0.2、0.1 mg/kg,其余17种邻苯二甲酸酯类增塑剂的定量下限均小于50μg/kg,RSD小于12%,平均加标回收率为86%～95%。采用该方法对47个市售皮革制品进行测定,结果在2个样品中检出多种邻苯二甲酸酯类增塑剂。     

Analysis of Phthalate Plasticizers for PVC by Liquid Chromatography

Abstract

A technique has been developed for the identification of phthalate plasticizer components using high speed liquid chromatography. The plasticizers recovered from post consumer scrap PVC have been analyzed.     

Use of the Eurachem guide on method validation for determination of uranium in environmental samples

Three analytical methods for determination of uranium in environmental samples by a fluorescence technique have been validated and compared in accordance with the Eurachem Guide on method validation. The first method depends on uranium separation from iron using the mercury anode technique; in the other two methods uranium is separated from iron on an anion exchange column by use of either a solution of hydrochloric acid containing ascorbic acid and hydrazine hydrate or a dilute sulfuric acid solution. Detection limits, repeatability, reproducibility, and recovery coefficient were the main validation characteristics. The results showed that better statistical values can be achieved by using the third method. Control charts for in-house control samples and international intercomparison samples have also shown that the third method is more statistically stable with time. In addition, uncertainties of measurement were estimated and compared for the three methods. It was found that the Eurachem Guide and comparison of quality statistical validation data can be good tools for selection of the appropriate method for an application.     

环境样品中五氯苯酚分析方法的研究进展

本文概述了国内外环境样品中五氯苯酚(PCP)测定方法的研究状况,包括分光光度法、HPLC法、GC法和免疫分析法等。重点介绍了PCP的提取、衍生化过程,同时总结了各种方法的优缺点。引用文献19篇。     

聚氯乙烯膜修饰碳微电极的研制及应用

采用浸涂流延法制得ＰＶＣ膜修饰碳微电极,用Ｋ３Ｆｅ（ＣＮ）６的循环伏安图考察了电极的电化学性能,并用此电极建立了环境水样中痕量汞的阳极溶出伏安法测定。在０．０６ｍｏｌ／Ｌ ＫＳＣＮ＋０．０１ｍｏｌ／ＬＫＣｌ介质中,富集电位－０．８０Ｖ,搅拌富集时间３００ｓ,扫描电压范围－０．２０～０．４０Ｖ,扫描速率３１４ｍＶ／ｓ,咄峰电流与Ｈｇ＾２＋浓度在０．０１～２．０ｍｇ／Ｌ的范围内有良好的线性关系,本电极     

Analysis of 16 phthalic acid esters in food simulants from plastic food contact materials by LC‐ESI‐MS/MS

An RP LC‐ESI‐MS/MS method for the determination of the migration of 16 primary phthalic acid esters from plastic samples has been developed using distilled water, 3% acetic acid, 10% alcohol, and olive oil as food simulants. Detection limits were 1.6–18.5 μg/kg in distilled water, 1.4–17.3 μg/kg in 3% acetic acid, 1.4–19.2 μg/kg in 10% alcohol, and 31.9–390.8 μg/kg in olive oil. The RSDs were in the range of 0.07–11.28%. The real plastic products inspection showed that only few analyzed samples were phthalates contaminated. Bis‐2‐ethylhexyl ester and dibutyl phthalate were the common items migrated from the plastic products into food and feeds, but the migration concentrations were far below the limits set by European Union (1.5 mg/kg for bis‐2‐ethylhexyl ester and 0.3 mg/kg for dibutyl phthalate).     

环己烷1,2-二甲酸二异壬酯增塑剂的气相色谱-质谱分析

建立了气相色谱-质谱联用法定性和定量分析塑料中环己烷1,2-二甲酸二异壬酯(DINCH)的方法。考察了DINCH分子离子的质谱断裂过程,并建立了快速鉴定塑料中DINCH的理论方法。通过对不同溶剂提取效率的对比,采用二氯甲烷作为最佳提取溶剂。在优化条件下,该方法的线性范围为0.24～1.60 mg/L,相关系数为0.998,定量下限(S/N=10)为1.2 mg/kg。在加标水平为80～400 mg/kg时,4种不同塑料(PE、PP、PU、PVC)的回收率和相对标准偏差分别为82%～113%和1.1%～9.0%。将该方法用于实际塑料样品的检测,结果满意。     

超高交联树脂NXD-4对水中邻苯二甲酸单丁酯的去除性能

以新合成的超高交联吸附树脂NXD-4为吸附剂,以邻苯二甲酸单丁酯(MBP)为目标污染物,通过吸附等温线和动力学实验,考察了NXD-4对MBP的去除性能并与活性炭AC-1进行了对比。结果表明,NXD-4和AC-1对MBP的去除均以物理吸附为主,在288~313 K温度范围内,最大吸附量随温度的升高而降低;相同条件下,NXD-4对MBP的吸附量明显大于AC-1的;而且,它们对MBP均具有较快的去除速率,在1750min左右即可达到吸附平衡,但AC-1对MBP的吸附速率大于NXD-4的;脱附再生实验表明,相比于AC-1,NXD-4的脱附再生效果更好,脱附率可以达到96%以上。因此,NXD-4作为吸附剂,对水体中邻苯二甲酸单酯的去除方面具有良好的应用前景。     

SPE/LC/ESI/MS with phthalic anhydride derivatisation for the determination of alcohol ethoxylate surfactants in sewage influent and effluent samples

A new method for the analysis of alcohol ethoxylates (AEs) using electrospray ionisation liquid chromatography/mass spectrometry (ESI LC/MS) is described. The procedure incorporates a novel derivatisation step with phthalic anhydride for the analysis of EO0-20 ethoxylates in a single analysis. The derivatives obtained have proved to be very stable and the negative ion spectra show reduced background ions and competing adduct formation as compared to positive ion spectra. An automated solid phase extraction (SPE) step is used to allow both pre-concentration and clean-up of the environmental samples. The method provides more efficient recovery of AEs across the C12-C18 range than previously reported in the literature. Recoveries from final effluent spiked at 100 microg/L total AE, for the 126 species analysed, were found to be in the range 55-117%, with approximately 100 of the individual analytes having recoveries of 90-105%. An LOD of 0.02 microg/L for individual ethoxylate components is reported with the instrument operated in scan mode over the range m/z 300-1300. The method was applied to sewage effluent and influent samples, with AEs determined at approximately 7 and 5000 microg/L, respectively.     

Critical Evaluation of Protonation Constants. Literature Analysis and Experimental Potentiometric and Calorimetric Data for the Thermodynamics of Phthalate Protonation in Different Ionic Media

The protonation constants of phthalate were determined in aqueous NaCl (0.1 ≤ I ≤ 5,mol⋅L⁻¹) and in aqueous Me₄NCl (0.1 mol⋅L⁻¹ ≤ I ≤ 3,mol⋅L⁻¹) at t = 25,^∘C. Experimental data were employed in conjunction with literature data from studies in different ionic media (Et₄NI: 0 ≤ I ≤ 1,mol⋅L⁻¹; NaClO₄: 0.05 mol⋅L⁻¹ ≤ I ≤ 2,mol⋅L⁻¹)to study the dependence on ionic strength using different models, such as the SIT and Pitzer equations, and an Extended Debye-Hückel type equation. Experimental calorimetric data in NaCl and protonation constants at different temperatures in Et₄NI (5 ≤ t ≤ 45^∘C) and in NaClO₄ (15 ≤ t ≤ 35 ^∘C) were also used to study their dependence on temperature. Recommended equilibrium data are reported together with a short discussion of a prospective protocol for drawing these data.