Determination of polycyclic aromatic hydrocarbons in water samples using high-performance liquid chromatography with amperometric detection

The determination of polycyclic aromatic hydrocarbons (PAHs) using high-performance liquid chromatography (HPLC) with UV and fluorescence detection has been well established. Although most of the PAHs can be detected by these methods, some environmentally important polyaromatic compounds, such as acenaphthylene, do not show fluorescence and can only be determined by UV detection at higher concentrations. A sensitive and selective determination of acenaphthylene, acenaphthene and the six PAHs listed in the TVO, the German drinking water standard, is also possible by amperometric detection following HPLC separation. The method was applied to the determination of PAHs in different water samples after solid-phase extraction (SPE). The efficiency of the amperometric determination was found to be superior to UV detection (λ = 300 nm).     

Gas chromatographic-mass spectrometric study of the oil fractions produced by microwave-assisted pyrolysis of different sewage sludges

The pyrolysis of sewage sludge was studied in a microwave oven using graphite as microwave absorber. The pyrolysis temperature ranged from 800 to 1000 degrees C depending on the type of sewage sludge. A conventional electrical furnace was also employed in order to compare the results obtained with both methods. The pyrolysis oils were trapped in a series of condensers and their characteristics such as elemental analysis and calorific value were determined and compared with those of the initial sludge. The oil composition was analyzed by GC-MS. The oils from the microwave oven had n-alkanes and 1-alkenes, aromatic compounds, ranging from benzene derivatives to polycyclic aromatic hydrocarbons (PAHs), nitrogenated compounds, long chain aliphatic carboxylic acids, ketones and esters and also monoterpenes and steroids. The oil from the electric oven was composed basically of PAHs such as naphthalene, acenapthylene, phenanthrene, fluoranthene, benzo[a]anthracene, benzofluoranthenes, benzopyrenes, indenepyrene, benzo[ghi]perylene, and anthanthrene. In contrast, these compounds were not produced in the case of microwave-assisted pyrolysis.     

Automated high-capacity sorption probe for extraction of organic compounds in aqueous samples followed by gas chromatographic analysis

An automated high-capacity sorption device for GC analysis of ultra trace components has been developed. The scope of the presented technique was to combine the simplicity of solid-phase microextraction (SPME) with the high extraction efficiency of the stir bar sorptive extraction technology. Sorptive extractions of water samples were performed using polydimethylsiloxane (PDMS) rubber tubing (120 microl) mounted onto a glass rod. The sampling procedure was carried out by a robotic autoinjector. Since the setup is fully automated, unattended and precise time-controlled extraction of samples is possible and makes quantitation with non-equilibrium extractions feasible. The sorption probes are easy to exchange, which facilitates off-line/in-field sampling. The system was evaluated with a test mixture of 44 environmentally hazardous compounds. Detection limits were found to be in the sub-ppt region. The performance of the system was demonstrated with the analysis of polycyclic aromatic hydrocarbons in urban snow.     

Calibration bias in the determination of polynuclear aromatic hydrocarbons in water

 We present the results of an investigative interlaboratory test to determine the reasons for poor agreement between data from different laboratories for the determination of polynuclear aromatic hydrocarbons in water. Received: 2 July 1998 · Accepted: 1 August 1998     

Screening methodology for coal-derived organic contaminants in water

A screening methodology designed to detect the presence of organic materials that leach into water from coal deposits was developed and evaluated. Analytical objectives included the ability to detect 16 polynuclear aromatic hydrocarbons (PAHs) at the lowest practical levels, capability for fingerprint analysis of other compounds, and ease of use under remote field conditions. The approach developed involved drawing 1?L water samples through a styrene divinylbenzene-based solid-phase extraction cartridge by suction, elution of the cartridge with tetrahydrofuran/hexane, evaporative concentration of the eluent, and reconstitution in acetonitrile, followed by analysis using high-pressure liquid chromatography with ultraviolet absorption and fluorescence detectors. The method was found to be easy to use under field conditions, providing generally acceptable recoveries and, in most cases, lower detection limits than current regulatory methods. The ability to detect PAHs and other organic compounds in simulated coal leachate solutions was demonstrated.     

Effect of moisture on supercritical fluid extraction of polynuclear aromatic hydrocarbons and phenols from soil using an automated extractor

An automated supercritical fluid extraction system was evaluated with polynuclear aromatic hydrocarbons and phenols to demonstrate extraction efficiency, collection efficiency, and sample cross contamination. Results showed that 75/25 glass beads/octadecyl silica provided the highest collection efficiency for these classes of compounds. Also, the automated SFE system was used to study the effect of different percentages of water (w/w) in soil on extraction efficiency of fortified PAH and phenols at different temperatures and pressures. Results showed that the presence of (available) water in soil (>10%) does, increase extraction efficiency of higher molecular weight PAH at higher temperature. Also it was demonstrated that temperature rather than pressure had a marked effect on extraction efficiency. The extraction efficiency of phenols from soil which contained 5% of water, using pure supercritical CO₂, was higher than those obtained from dry soil or soil containing 1 % water. Extraction of phenols from soil did not show a dependence on pressure or temperature.     

Gas chromatographic determination of aromatic amines in water samples after solid-phase extraction and derivatization with iodine: I. Derivatization

A new method for the selective determination of aromatic amines is presented, which is based on the solid-phase extraction at pH 9 and subsequent derivatization of the analytes to the corresponding iodobenzenes. These can selectively and sensitively be determined with gas chromatography and electron-capture detection. Separation of at least 30 compounds in a single chromatographic run in 30 min is possible. With this method, 56 aromatic amines were investigated, and only in six cases no derivatives were obtained. Limits of quantitation were between 0.5 and 8 μg l⁻¹, but may still be lowered with higher sample volumes or different injection techniques. The application to water samples revealed the suitability for the investigation of ground, leachate and wastewater.     

Preparation and characteristics of sol-gel-coated calix[4]arene fiber for solid-phase microextraction

5,11,17,23-Tetra-tert-butyl-25,27-diethoxy-26,28-dihydroxycalix[4]arene/hydroxy-terminated silicone oil coated fiber was first prepared and applied for solid-phase microextraction (SPME) with sol-gel technology. The possible sol-gel mechanism was discussed and confirmed by IR spectra. It showed wonderful selectivity and sensitivity to polar (aromatic amines), nonpolar (benzene derivatives, polycyclic aromatic hydrocarbons) and high boiling point compounds (phthalates) and the extraction equilibria were reached quite fast. The coating has high thermal stability (380 degrees C) and solvent stability (organic and inorganic), thus its lifetime is longer than conventional fibers. In addition, it has surprising fiber-to-fiber and batch-to-batch reproducibility. The detection limits were quite low and the linear ranges were pretty broad for all analytes.     

Comparison of different commercial solid-phase extraction cartridges used to extract heterocyclic amines from a lyophilised meat extract

Heterocyclic amines are a group of potent mutagenic compounds which are generated when muscle meat is cooked. Since they are possible human carcinogens, these mutagens have received considerable attention in recent years, and several analytical techniques have been developed for their quantification. Although the purification step is one of the most important, there are a great number of variables influencing the recovery of the amines, especially when real samples are analysed. In this work we studied the influence of sample spiking mode on the recoveries. Furthermore, on the basis of a previously developed clean-up method, the effect of changing commercial source and structure of the sorbents used in two solid-phase extraction steps was examined. This purification method was applied to the quantification of the heterocyclic aromatic amines present in a lyophilised meat extract by means of liquid chromatography–mass spectrometry.     

Ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to gas chromatography-mass detection

Continuous ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to their individual separation and determination by gas chromatography (GC) with MS-MS detection is presented here. A multivariate optimisation of the variables affecting the continuous extraction step (namely, probe position, ultrasound radiation amplitude, percentage of duty cycle of ultrasonic exposure, sonication time, total extractant volume, extractant flow rate and temperature of the water-bath in which the extraction cell was placed) was performed. The method was compared with the reference EPA method 3540 using natural contaminated soils. Similar efficiencies were obtained but with a drastic reduction of both the extraction time (10 min versus 24 h) and the extractant volume (less than 10 ml versus 100 ml) by the proposed method. Detection limits of low picogram were obtained, with repeatability and reproducibility between 4.21-5.70 and 5.20-7.23%, respectively.     

Determination of organic micropollutants in rainwater using hollow fiber membrane/liquid-phase microextraction combined with gas chromatography-mass spectrometry

A simple and rapid liquid-phase microextraction (LPME) method using a hollow fiber membrane (HFM) in conjunction with gas chromatography-mass spectrometry (GC-MS) is presented for the quantitative determination of 16 polycyclic aromatic hydrocarbons (PAHs) and 12 organochlorine pesticides (OCPs) in rainwater samples. The LPME conditions were optimized for achieving high enrichment of the analytes from aqueous samples, in terms of hollow fiber exposure time, stirring rate, sample pH, and composition. Enrichment factors of more than 100 could be achieved within 35 min of extraction with relative standard deviations (R.S.D.s) 1.3-13.6% for PAHs and 1.7-13.8% for OCPs, respectively, over a wide range of analyte concentrations. Detection limits ranged from 0.002 to 0.047 microg l(-1) for PAHs, and from 0.013 to 0.059 microg l(-1) for OCPs, respectively. The newly developed LPME-GC-MS method has been validated for the analysis of PAHs and OCPs in rainwater samples. Extraction recoveries from spiked synthetic rainwater samples varied from 73 to 115% for PAHs and from 75 to 113% for OCPs, respectively. Real rainwater samples were analyzed using the optimized method. The concentrations of PAHs and OCPs in real rainwater samples were between 0.005-0.162, and 0.063 microg l(-1), respectively.     

Electron capture detector response to low electron affinity aromatic hydrocarbons using positive ion stabilization and alkyl chloride sensitization

The electron capture detector (ECD) response to numerous aromatic hydrocarbons of low electron affinity (EA) is shown to be detrimentally affected by two processes which compete with and typically overwhelm the electron capture reactions of these molecules. It is shown that the effects of these two undesired reactions can be eliminated by the permanent addition of trimethylamine and one of several alkyl monochlorides to the detector make-up gas. These modifications of the detector gas result in greatly increased sensitivity, increased linearity, and increased reproducibility of response. A kinetic model for the ECD responses of low EA resonance capture molecules is developed which appears to explain these improvements.     

Comparison of different trapping methods for pressurised hot water extraction

Four trapping methods for pressurised hot water extraction were compared in terms of recovery and selectivity. Also, robustness, repeatability and solvent consumption of the trapping systems were investigated. The trapping methods were collection into solvent following liquid-liquid extraction, solid-phase trapping into Tenax TA (SPE), flat sheet microporous membrane liquid-liquid extraction and hollow fibre microporous membrane liquid-liquid extraction. Polycyclic aromatic hydrocarbons were extracted with these systems from four soil and sediment matrices and the extracts were analysed by GC-MS and size-exclusion chromatography. Clear differences were observed in the selectivity and extraction efficiencies of the trapping systems.     

SFE of PAHs from soils with a high carbon content and analyte collection via combined liquid/solid trapping

Polynuclear aromatic hydrocarbons (PAHs) are recovered from a soil with a high carbon content (ca. 50%) with supercritical fluid extraction (SFE) as well as with conventional Soxhlet extraction. The influence of temperature and modifier volume on SFE efficiency and the effect of a combined liquid/solid trap for analyte collection are investigated in this study. Such traps, which make analyte collection and clean-up possible in one step, are compared with conventional analyte collection in pure organic solvents. A comparison between reproducibility and efficiency of SFE and Soxhlet extraction is presented.     

Fluorescence optosensors based on different transducers for the determination of polycyclic aromatic hydrocarbons in water

This paper presents the development of two optosensors for the determination of four polycyclic aromatic hydrocarbons (anthracene, benzo[a]pyrene, fluoranthene and benzo[b]fluoranthene) using a photomultiplier device and an intensified coupled charge device (ICCD) as optical transducers, respectively. These optosensors are based on the on-line immobilization of the analytes onto a non-ionic resin solid support (Amberlite XAD-4) in a continuous flow system, followed by the measurement of their native fluorescence. The determinations were performed using 15 mM H₂PO₄^-/HPO₄^2- buffer solution at pH 7 and 25% 1,4-dioxane. Detection limits were 6.4 and 9.3 for ANT, 3.3 and 2.5 for BbF, 1.4 and 13.2 for FLT, and 1.7 and 7.8 for BaP using optosensor 1 or 2, respectively. Relative standard deviations were 7.9 and 6.7 for ANT at 50 ng mL^-1, 3.5 and 7.4 for BbF at 60 ng mL^-1, 3.6 and 8.9 for FLT at 50 ng mL^-1, and 6.7 and 11.6 for BaP at 50 ng mL^-1 using optosensor 1 or 2, respectively. Finally, a critical comparison between the two configurations based on different transducers (photomultiplier and ICCD) for resolving and simultaneously determining mixtures of the polycyclic aromatic hydrocarbons under study in water samples (tap and mineral waters) were carried out.     

Development and validation of a subcritical 1,1,1,2‐tetrafluoroethane extraction technique: Gas chromatography–mass spectrometry method for the simultaneous determination of polycyclic aromatic hydrocarbons,polychlorinated biphenyls,and polybrominated biphenyl ethers in aquatic products

A simple, rapid, and green method was developed for the simultaneous analysis of polycyclic aromatic hydrocarbons, polychlorinated biphenyls, and polybrominated biphenyl ethers in aquatic products using subcritical 1,1,1,2‐tetrafluoroethane extraction coupled with gas chromatography and mass spectrometry. Effects of the extraction temperature, pressure, and cosolvent volume on the extraction efficiency were investigated by extracting spiked oyster samples. The results show that the maximum extraction efficiency was obtained at 40°C, 12 MPa, and a cosolvent (dichloromethane) volume of 5.0 mL. Under these conditions, the calibration curves had good linearity with square of the correlation larger than 0.998 in the concentration range of 5–800 ng/mL; limit of detection and limit of quantitation were 0.16–2.83 and 0.55–9.43 ng/g, respectively. At spiked levels of 10, 30, and 50 ng/g, the average recoveries were 70.4–80.4% for polycyclic aromatic hydrocarbons, 74.0–83.6% for polychlorinated biphenyls, and 66.9–78.0% for polybrominated biphenyl ethers, with average relative standard deviations of less than 16.3%. The established method has no significant differences in recovery compared to traditional methods and is suitable for the analysis of real samples.     

Parts per quadrillion level ultra-trace determination of polar and nonpolar compounds via solvent-free capillary microextraction on surface-bonded sol-gel polytetrahydrofuran coating and gas chromatography-flame ionization detection

Sol-gel polytetrahydrofuran (poly-THF) coating was developed for high-sensitivity sample preconcentration by capillary microextraction (CME). Parts per quadrillion (ppq) level detection limits were achieved for both polar and nonpolar analytes through sample preconcentration on sol-gel poly-THF coated microextraction capillaries followed by gas chromatography (GC) analysis of the extracted compounds using a flame ionization detector (FID). The sol-gel coating was in situ created on the inner walls of a fused silica capillary using a sol solution containing poly-THF as an organic component, methyltrimethoxysilane (MTMOS) as a sol-gel precursor, trifluoroacetic acid (TFA, 5% water) as a sol-gel catalyst, and hexamethyldisilazane (HMDS) as a deactivating reagent. The sol solution was introduced into a hydrothermally-treated fused silica capillary and the sol-gel reactions were allowed to take place inside the capillary for 60 min. A wall-bonded coating was formed due to the condensation of silanol groups residing on the capillary inner surface with those on the sol-gel network fragments evolving in close vicinity of the capillary walls. Poly-THF is a medium polarity polymer, and was found to be effective in carrying out simultaneous extraction of both polar and nonpolar analytes. Efficient extraction of a wide range of trace analytes from aqueous samples was accomplished using sol-gel poly-THF coated fused silica capillaries for further analysis by GC. The test analytes included polycyclic aromatic hydrocarbons (PAHs), aldehydes, ketones, chlorophenols, and alcohols. To our knowledge, this is the first report on the use of a poly-THF based sol-gel material in analytical microextraction. Sol-gel poly-THF coated CME capillaries showed excellent solvent and thermal stability (>320 degrees C).     

The effects of modifiers in supercritical fluid chromatography

Investigations have been initiated to examine the basic elements of resolution and how they vary individually and collectively in terms of modifiers used in supercritical fluid chromatography (SFC). Capacity factors (k′) have been determined for a mixture of polynuclear aromatic hydrocarbons from SFC experiments as function of modifier identity and concentration using different stationary phases. Using carbon dioxide as the primary mobile phase, the modifiers investigated included methanol, 2-methoxy ethanol, 1-propanol, tetrahydrofuran, dimethyl sulfoxide, acetonitrile, sulfur hexafluoride, and freon 11.