Modification of B-site doping of perovskite LaxSr1 − xFe1 − y−zCoyCrzO3 − δ oxide by Mg2+ ion

Co-doping B-site of perovskite oxide La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCFO) with Cr⁶⁺ and Mg²⁺ ions has been attempted in this research for revamping chemical stability and oxygen ionic conductivity of this mixed conducting oxide. It is known that partial substitution for B-site cations of LSCFO by Cr gives rise to a significant improvement on chemical and thermal stability of the perovskite oxide. On the basis of this doped structure, introduction of an immaterial dose of Mg²⁺ ion into its B-site results in a microstructure consisting of smaller grains with higher density than its precursor. Furthermore, the resulting perovskite oxide La_0.19Sr_0.8Fe_0.69Co_0.1Cr_0.2 Mg_0.01O_3 ? δ (LSFCCMO) displays higher O^2? conductivity than the solely Cr-doped LSCFO besides the improved chemical stability against reduction in 5% CH₄/He stream at 850 °C. A detailed examination of the oxidation states of B-site transition metal ions by XPS has also been conducted as a part of structural characterizations of LSFCCMO. The assessment of relative O^2? conductivity shows that the grain boundary area plays a more important role than the bulk phase in facilitating ion transport, but with comparable boundary areas the higher densification level is favorable.     

Propagation characteristics of Gaussian beams through 2 × 2 square matrix circular apertures

Based on the expansion of the hard aperture function into a finite sum of complex Gaussian functions, using Collins formula, the approximate analytical expression of Gaussian beams through 2 × 2 square matrix circular apertures is derived. Finally, some numerical examples are given to illustrate the analytical results by Matlab. It is shown that the propagation characteristics is related with the propagation distance z, the radius of circular aperture a and the distance d. The results can be directly used in other beams and square matrix apertures, and be applied to control beams and optical system designing.     

Atomic and nanostructures of monolayer c(2 × 2)NiN on Cu(0 0 1)

Structures of monolayer nickel nitride (NiN) on Cu(0 0 1) surface are studied by X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). Formations of Ni–N chemical bonds and NiN monolayer at the surface are confirmed by XPS on the N-adsorbed Cu(0 0 1) surfaces after Ni deposition and subsequent annealing to 670 K. A c(2 × 2) structure is always observed in the LEED patterns, which is a quite contrast to the (2 × 2)p4g structure observed usually at the N-adsorbed Ni(0 0 1) surface. Atomic images by STM indicate the mixture of Ni–N and Cu–N structures at the surface. Density of the trenches on the N-saturated surface decreases and the grid pattern on partially N-covered surfaces becomes disordered with increasing the Ni coverage. These results are attributed to the decrease of the surface compressive stress at the N-adsorbed Cu surface by mixing Ni atoms.     

On the superconductivity and structural properties of YBa2Cu3 − xCdxO7 − y

A series of superconducting cuprates with the nominal composition YBa₂Cu_3 − xCd_xO_7 − yand the effect of Cd substitution on Cu sites in this compound is presented. X-ray powder diffraction patterns for these cadmium cuprates with reduced diamagnetism indicate an orthorhombic unit cell like-perovskite structure for (0 ≤ x ≤ 0.15), while for higher Cd concentration, i.e.x = 1.0 the material is polyphasic. The observed superconducting transition temperature of the samples is nearly the same ([formula] K), except for (x = 1.0) whereT_cdrops to 72 K and a transition from metallic to semiconducting behavior of the normal state of the resistivity is observed. Such a decrease inT_cfor higher Cd concentration could be attributed to the presence of the green phase in this composition.     

Passivation effect of allylamine molecule on the electronic structure of a Si(001) − (2 × 1) surface

The chemisorption of the allylamine molecule, which contains two functional groups (ethenyl and hydroxyl), on a Si(001) ? (2 × 1) surface was studied using density functional theory (ab-initio DFT) based on the pseudopotential approach. In particular, we focused on the determination of the most stable position of the CC double bond in the ethenyl group and observation of the passivation effect of allylamine on the electronic structure of the clean Si(001) ? (2 × 1) phase. For this purpose, all of the possible interaction mechanisms occurring at the interface were considered: (i) dissociative bonding where the CC bond is parallel to the silicon surface, (ii) dissociative bonding where the CC bond is perpendicular to the silicon surface, and (iii) the [2 + 2] CC cycloaddition reaction. From our total energy calculations, it was found that the bifunctional allylamine molecule attached to the Si(001) ? (2 × 1) surface through the amino functional group, by breaking the N–H bond and forming a Si–H bond and Si–NHCH2CHCH2 surface fragments. During this process, the ethenyl functional group remains intact, and so can be potentially used as an extra reactive site for additional chemical interactions. In addition to these findings, the nudged elastic band method (NEB) calculations related with the reaction paths showed that the parallel position of the CC bond with respect to the surface of the substrate is more favorable. In order to see the influence of the chemisorbed allylamine molecule on the surface states of the clean Si(001) – (2 × 1), we also plotted the density of states (DOS), in which it is seen that the clean Si(001) – (2 × 1) surface was passivated by the adsorption of allylamine.     

Synthesis and Gas-Sensing Properties of MnO2 – x and MnO2 – x/CuO-Coated Multiwalled Carbon Nanotube Nanocomposites

Physics of the Solid State - Nanocomposites based on multiwall carbon nanotubes (MWCNTs) impregnated with manganese oxide MnO2 – x and copper oxide CuO are synthesized and...     

Coverage dependence of glycine adsorption on the Ge(100) − 2 × 1 surface

A combination of infrared spectroscopy, X-ray photoelectron spectroscopy and density functional theory has been used to investigate the adsorption behavior of glycine at the Ge(100) ? 2 × 1 surface under ultrahigh vacuum conditions. Comparison of experimental and simulated IR spectra indicates that at 310 K, glycine adsorbs on Ge(100) ? 2 × 1 via O–H dissociation, with some fraction of the products also forming an N dative bond to a neighboring germanium atom. O–Ge dative bonding is not observed. As coverage increases, the surface concentration of the monodentate O–H dissociated adduct increases, while that of the N dative-bonded species appears constant. XPS data support and clarify the IR findings and reveal new insights, including the presence at higher coverage of a minor product that has undergone dual O–H and N–H dissociation. These findings are supported by the calculated energy diagrams, which indicate that the reaction of a glycine molecule on the Ge(100) ? 2 × 1 surface via O–H dissociation and interdimer N dative bonding is both kinetically and thermodynamically favorable and that N–H dissociation of this adduct is feasible at room temperature given incomplete thermal accommodation along the reaction pathway.     

The high-resolution FTIR spectrum of the ν4 + ν8 band of trans-d2-ethylene (trans-C2H2D2)

The FTIR absorption spectrum of the hybrid A–B type ν₄ + ν₈ combination band of trans-C₂H₂D₂ centered at 1845.98737 cm^?1 in the 1730–1940 cm^?1 region was recorded at an unapodized resolution of 0.0063 cm^?1. A total of 2725 a- and b-type transitions was assigned and fitted to upper state (ν₄ + ν₈ = 1) rovibrational constants up to sextic terms using Watson’s A-reduced Hamiltonian in I^r representation. The b-type feature of the band was analyzed for the first time. The root-mean-square deviation of the IR fit was 0.00059 cm^?1. The most accurate set of ground state rovibrational constants up to sextic terms was also derived from the simultaneous fit of 3340 ground state combination differences from the present analysis and the ν₄ band of trans-C₂H₂D₂. The transition dipole moment ratio $\left|\frac{{\mu }_a}{{\mu }_b}\right|$ was found to be 1.95 ± 0.06.     

Radiation stability of M1 − xPrxF2 + x (M = Ca,Sr, Ba) crystals

The radiation stability of the mixed crystals M_1 ? xR_xF_2 + x (M = Ca, Sr, Ba) depends on types of the alkaline-earth and rare-earth ions. Different to Eu- and Ce-containing systems, M_1 ? xPr_xF_2 + x solid solutions have a low radiation resistance, which may be associated with hole trapping on praseodymium ion according to the reaction Pr³⁺ → Pr⁴⁺ which is typical for praseodymium. The coloration efficiency of M_1 ? xPr_xF_2 + x crystals grows in the row Ca → Sr → Ba, which is explained satisfactorily within the model of rare-earth clusters, the structure of which is determined by the ratio of the base alkaline-earth cation to the praseodymium ion radii.     

Ga-induced restructuring of Si(5 5 12) − 2 × 1 reconstructed surface at room temperature

Motivated by the need to form 1D-nanostructured dopants on silicon surfaces, we have attempted to grow Ga on the high index Si(5 5 12) surface which has a highly trenched (1D) morphology. The evolution of the interface with Ga adsorption in the monolayer regime has been probed by in situ AES, LEED and EELS. Controlling the kinetics by changing the Ga flux rates shows an interesting difference in the 1.0 to 1.5 ML region. The low flux rate (0.03 ML/minute) results in a Frank van der Merwe (layer by layer) growth mode up to 2 ML, while the higher flux rate (0.1 ML/minute) shows a transient island formation after the completion of 1 ML. The low rate shows the formation of 2 × (3 3 7) and (2 2 5) superstructures, while only the 2 × (3 3 7) is observed in a wide coverage range for the higher rate. The results demonstrate the ability to kinetically control the surface phases with different electronic properties of this technologically important interface.     

1.55 μm silicon-based reflection-type waveguide-integrated thermo-optic 2 × 2 switch

In this work a waveguide-integrated 2 × 2 switch operating at the infrared communication wavelength of 1550 nm is proposed and theoretically discussed. The device is based on the total internal reflection (TIR) phenomenon and the thermo-optic effect (TOE) in hydrogenated amorphous silicon (a-Si:H) and crystalline silicon (c-Si). It takes advantage of a bandgap-engineered a-Si:H layer to explore the properties of an optical interface between materials showing similar refractive indexes but different thermo-optic coefficients. In particular, thanks to modern plasma-enhanced chemical vapour deposition (PECVD) techniques, the refractive index of the amorphous film can be properly tailored to match that of c-Si at a given temperature. TIR may be therefore achieved at the interface by acting on the temperature. The device is integrated in a 4 μm-wide and 3 μm-thick single-mode rib waveguide. The substrate is a silicon-on-insulator (SOI) wafer with an oxide thickness of 500 nm. We calculated an output crosstalk always better than 24 dB and insertion losses as low as 3.5 dB.     

NMR and electric impedance study of lithium mobility in fast ion conductors LiTi2 − xZrx(PO4)3 (0 ≤ x ≤ 2)

Materials of the LiTi_2 − xZr_x(PO₄)₃ series (0 ≤ x ≤ 2) were prepared and characterized by powder X-ray (XRD) and neutron diffraction (ND), ⁷Li and ³¹P Nuclear Magnetic Resonance (NMR) and Electric Impedance techniques. In samples with x < 1.8, XRD patterns were indexed with the rhombohedral R3̅c space group, but in samples with x ≥ 1.8, XRD patterns display the presence of rhombohedral and triclinic phases. The Rietveld analysis of the LiTi_1.4Zr_0.6(PO₄)₃ neutron diffraction (ND) pattern provided structural information about intermediate compositions. For low Zr contents, compositions deduced from ³¹P MAS-NMR spectra are similar to nominal ones, indicating that Zr⁴⁺ and Ti⁴⁺ cations are randomly distributed in the NASICON structure. At increasing Zr contents, differences between nominal and deduced compositions become significant, indicating some Zr segregation in the triclinic phase. The substitution of Ti⁴⁺ by Zr⁴⁺ stabilizes the rhombohedral phase; however, electrical performances are not improved in expanded networks of Zr-rich samples. Below 300 K, activation energy of all samples is near 0.36 eV; however, above 300 K, activation energy is near 0.23 eV in Ti-rich samples and close to 0.36 eV in Zr-rich samples. The analysis of electrical data suggests that the amount of charge carriers and entropic terms are higher in Zr-rich samples; however, the increment of both parameters does not compensate lower activation energy terms of these samples. As a consequence of different contributions, the bulk conductivity of Zr-rich samples, measured at room temperature, is one order of magnitude lower than that measured in Ti-rich samples.     

First principle study of structural,phase stabilization and oxygen-ion diffusion properties of β-La2 − xLxMo2O9 (L = Gd,Sm, Nd and Bi) and β-La2Mo2 − yMyO9 (M = Cr,W)

We have performed a first principle study of structural and phase stabilization of β-La_2 ? xL_xMo₂O₉ (L = Gd, Sm, Nd and Bi) and β-La₂Mo_2 ? yM_yO₉ (M = Cr, W). The substitutional-site properties were discussed in terms of the empirical parameter, bond valence sums (BVS), which characterizes the interactions between atoms and its nearest-neighbor atoms and correlates well with the stability of the structure. We found that Gd, Sm and Nd atoms prefer the crystallographic sites with largest BVS values. The nonlinear dependence of cell parameter on W content in W-doped systems results from the nonlinear change in Mo/W–O bond length with W content. The decrease of cohesive energy and the deviation of BVS values from the expected values upon the Gd, Sm, Nd and W-doped concentration help us understand the experimentally observed stabilization of the β phase to lower temperatures in these doped system. The O ion diffusion properties in W-doped systems have been studied using the nudged elastic band method and the dimer method. We found that, W-doping leads to the obvious increase in the energy barriers of O ion concerted diffusion. In addition, there is a remarkable decrease in the difference of energy barriers between two diffusion channels involving O(1) ion, which sheds light on only one relaxation peak in the mechanical relaxation measurement in W-doped system, compared to undoped system.     

Electronic structure of CuClxBr1 − x,CuClxI1 − xand CuBrxI1 − xalloys

In this work, the electronic structure and disorder effects in copper halides alloys are studied by means of the full potential linearized augmented plane wave (FLAPW) method. The calculated bowing parameter shows that the main contribution is due to the relaxation effects, though the charge transfer remains relatively significant, while the volume deformation contribution is negligible. The total bowing is found to be small in the three studied alloys. Results agree well with experimental and available theoretical works.     

Topmost-surface-sensitive Si-2p photoelectron spectra of clean Si(1 0 0)-2 × 1 measured with photoelectron Auger coincidence spectroscopy

Topmost-surface-sensitive Si-2p photoelectron spectra of a clean Si(1 0 0)-2 × 1 surface have been measured using Si-2p photoelectron Si-L₂₃VV Auger coincidence spectroscopy (Si-2p–Si-L₂₃VV PEACS). The escape depth of the PEACS electrons is estimated to be ～1.2 Å. The results support the assignments of the Si up-atoms, the Si down-atoms, the Si 2nd-layer, and the Si bulk proposed in previous researches. The Si-2p component with a binding energy of ?0.23 eV relative to the bulk Si-2p_3/2 peak, is shown to originate mainly from the topmost surface. Site selectivity of PEACS is indicated to be achieved to some degree by carefully selecting the kinetic energy of the Auger electrons. Since PEACS can be applied to any surface, the present study opens a new approach to identify PES components.     

First principles total energy calculations of the adsorption of germane and digermane on Si(0 0 1)-c(2 × 4)

First principles total energy studies are performed to investigate the energetics, and the atomic structure of the adsorption of germane (GeH₄), and digermane (Ge₂H₆) on the Si(0 0 1)-c(2 × 4) surface. It has been observed experimentally that adsorption of Ge₂H₆ is a dissociative process, which first yields GeH₃ and then GeH₂ fragments as products. We first study the adsorption of GeH₂ considering two different models; the intra-row and the on-dimer geometries. Our results show that the on-dimer site is more stable than the intra-row geometry by 0.44 eV. This is not a surprise since in the absence of H atoms, adsorption in the on-dimer site leaves no dangling bonds. In contrast, when the GeH₂ fragment is considered together with two H atoms, the intra-row geometry is favored energetically as compared with the on-dimer site, in good agreement with experiment. Similar results have been previously obtained for the adsorption of SiH₂ on Si(0 0 1). Digermane adsorption is explored according to two different geometries. In the first one, we have considered the adsorption as two GeH₃ fragments, while in the second, we have considered the adsorption as two GeH₂ fragments plus 2 H fragments. In good agreement with experiments, it is found that the latter geometry is energetically more favorable.     

Oxygen nonstoichiometry and defect equilibrium in La2 − xSrxNiO4 + δ

Nonstoichiometric variation of oxygen content in La_2 ? xSr_xNiO_4 + δ (x = 0, 0.1, 0.2, 0.3, 0.4) and decomposition P(O₂) were determined by means of high temperature gravimetry and coulometric titration. The measurements were carried out in the temperature range between 873 and 1173 K and the P(O₂) range between 10^? 20 and 1 bar. La_2 ? xSr_xNiO_4 + δ showed the oxygen excess and the oxygen deficient compositions depending on P(O₂), temperature, and the Sr content. The value of partial molar enthalpy of oxygen approaches zero as δ increases in the oxygen excess region, which indicate that the interstitial oxygen formation reaction is suppressed as δ increase. The relationship between δ and logP(O₂) were analyzed by two types of defect equilibrium models. One is a localized electron model, and the other is a delocalized electron model. Both models can well explain the oxygen nonstoichiometry of La_2 ? xSr_xNiO_4 + δ with a regular solution approximation.     

Structural Transformations of Ni1 – xCuxFe2O4 Nanoparticles Depending on the Number of Cu Ions

Physics of the Solid State - Changes in the structure and properties of the Ni1&nbsp;–&nbsp;xCuxFe2O4 ferrites-spinel magnetic nanoparticles depending on the Cu ion concentration (0...     

Adsorption of O2 and CO2 on the Si(111)-7 × 7 surfaces

The interaction of O₂ and CO₂ with the Si(111)-7 × 7 surface has been studied with X-ray photoelectron spectroscopy (XPS). It was found that both O₂ and CO₂ molecules can readily oxidize the Si(111)-7 × 7 surface to form thin oxide films. Two oxygen species were identified in the oxide film: oxygen atoms binding to on-top sites of adatom/rest atoms with an O 1s binding energy of ~ 533 eV as well as to bridge sites of adatom/rest atom backbonds at ~ 532 eV. These two oxygen species can be interconverted thermally during the annealing process. Due to the low oxidation capability, the silicon oxide film formed by CO₂ has a lower O/Si ratio than that of O₂.