Anion receptor-coated separator for lithium-ion polymer battery

Anion receptor-coated separators were prepared by coating poly(ethylene glycol) borate ester (PEGB) as an anion receptor and poly(vinyl acetate) (PVAc) as a good adhesive material towards electrodes onto microporous polyethylene (PE) separators. Gel polymer electrolytes were fabricated by soaking them in an liquid electrolyte, 1 M LiPF₆ in EC/DEC/PC (30/65/5, wt.%). As the weight ratio of PEGB to PVAc in a coating layer increased, gel polymer electrolytes showed higher cationic conductivity and electrochemical stability. The cationic conductivity and electrochemical stability of the gel polymer electrolyte based on coated separator with PVAc/PEGB (2/5, weight ratio) could reach 2.8 × 10^–4 S cm^–1 and 4.8 V, respectively. Lithium-ion polymer cells (LiCoO₂/graphite) based on gel polymer electrolytes with and without PEGB were assembled, and their electrochemical performances were evaluated.     

Hollow mesoporous silica sphere-embedded composite separator for high-performance lithium-ion battery

Journal of Solid State Electrochemistry - A high-performance composite separator based on hollow mesoporous silica spheres, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP), and...     

Magnetron sputtering deposition of silicon nitride on polyimide separator for high-temperature lithium-ion batteries

To date,lithium-ion batteries are becoming increasingly significant in the application of portable devices and electrical vehicles,and revolutionary progress in theoretical research and industrial application has been achieved.However,the commercial polyolefin separators with unsatisfying electrolytes affinity and poor thermal stability have extremely restricted the further application of lithium-ion batteries,especially in the high-temperature fields.In this work,magnetron sputtering deposition technique is employed to modify the commercial polyimide separator by coating silicon nitride on both sides.Magnetron sputtering deposition modified polyimide(MSD-PI)composite separator shows high thermal stability and ionic conductivity.More importantly,compared with the cells using Celgard separator,the cells with MSD-PI separator exhibit superior electrochemical performance,especially long-term cycle performance under high temperature environment,owing to the high thermal conductivity of surface Si3 N4 particles.Hence,lithium-ion batteries with MSD-PI separator are capable of improving thermal safety and capacity retention,which demonstrates that magnetron sputtering deposition technique could be regarded as a promising strategy to develop advanced organic/inorganic composite separators for high-temperature lithium-ion batteries.     

Toxicity analysis of second use lithium-ion battery separator and electrolyte

Pyrolysis gas chromatography-mass spectrometry (Py-GC-MS) test, smoke toxicity analysis and mouse biological toxicity test were carried out on the second use lithium-ion battery separator and electrolyte. It was found that the types of cracked products of separator and electrolyte under different state of health (SOH) were basically the same, mainly phosphoryl fluoride (POF₃) and long-chain F-containing alkanes, alcohols and esters. The content of POF₃ in the cracked product increases as the SOH increases. The toxic gas components released after the separator and the electrolyte are completely burned mainly include CO, CO₂, and HF. The HF content decreased as the battery SOH decreased, from 101.6 mg/g of the 100% SOH battery to 44.1 mg/g of the 65% SOH battery. In the biological toxicity test, all the mice were found to stop running, close eyes, shed tears, and have shortness of breath. After the test, only 65% SOH and 100% SOH mice recovered their body weight to the pre-experimental average state and gained weight.     

Experimental and molecular simulating study on promoting electrolyte-immersed mechanical properties of cellulose/lignin separator for lithium-ion battery

Lithium-ion batteries have been developing intensively and earn an unprecedented reputation, yet advanced performance and safety issue still require considerable investigation. Separator is vital to comprehensive properties of batteries, where the mechanical properties are key to breaking through of new-type separator. Unfortunately, electrolyte submersion has caused damage to strength of cellulose separator. Whereupon, in this work, cellulose separator is optimized by introducing lignin particles to promote electrolyte-immersed mechanical strength. Experiments are conducted concerning surface morphology, contact angle, porosity, electrolyte uptake, mechanical properties and electrochemical performance. Molecular simulation is implemented to explore the mechanism of tensile behavior of cellulose and lignin subjected to electrolyte solvents. Experimental results confirm positive effect of lignin addition in improving mechanical properties and simultaneously maintaining impressive electrochemical performance of the cellulose/lignin composites separators. Besides, lignin addition amount of 2.5% and 5% is recommended to achieve promising overall properties. Molecular simulation has successfully unveiled that weakening of cellulose separator submerged in electrolyte is resulted by the deformed cellulose amorphous region and the promoting effect of adding lignin is contributed from the new hydrogen bonds generated between cellulose and lignin molecules. Hopefully, this work provides novel insight on preparing remarkable separator and mechanism of materials behavior.     

Recent advances on battery separators based on poly(vinylidene fluoride) and its copolymers for lithium-ion battery applications

Lithium-ion batteries represent one of the most suitable systems for effective energy storage for a wide range of applications, such as smartphones, laptops, electric vehicles, or even home storage systems. Among the different battery components, the separator plays an essential role in the performance of the batteries; its most relevant characteristics are (micro)structure, wettability, thermal and mechanical properties, and ionic conductivity value. This work provides a comprehensive review of the current state of the art in lithium-ion battery separator membranes based on poly(vinylidene fluoride) (PVDF) and its copolymers. The most recent developments in the last two years are presented, focusing on the different separator types that have been developed with the aim of improving wettability, thermal characteristics, and cycling behavior. The most used types of PVDF separators are composites, polymer blends, and the combination of both. Among the most common fillers, metal–organic frameworks, ionic liquids, and ceramic particles have been used for the development of PVDF-based composites and polymers such as poly(m-phenylene isophthalamide), poly(acrylonitrile), poly(tetrafluoroethylene), or poly(methyl methacrylate), for the development of polymer blends. Electrospinning is one of the most used processing techniques to improve wettability, thermal stability, and mechanical properties. The wettability of separators has been also improved by using PVDF as a coating on commercial separators.It is shown that PVDF-based battery separators can play an important role in the next generation of high-performance batteries.     

Novel sulfonated polyimide/ZrO2 composite membrane as a separator of vanadium redox flow battery

Sulfonated polyimide (SPI) and ZrO₂ are blended to prepare a series of novel SPI/ZrO₂ composite membranes for vanadium redox flow battery (VRFB) application. Results of atomic force microscopy and X‐ray diffraction reveal that ZrO₂ is successfully composited with SPI. All SPI/ZrO₂ membranes possess high proton conductivity (2.96–3.72 × 10^?2 S cm^?1) and low VO²⁺ permeability (2.18–4.04 × 10^?7 cm² min^?1). SPI/ZrO₂‐15% membrane is determined as the optimum one on account of its higher proton selectivity and improved chemical stability. The VRFB with SPI/ZrO₂‐15% membrane presents higher coulombic efficiency and energy efficiency than that with Nafion 117 membrane at the current density, which ranged from 20 to 80 mA cm^?2. Cycling tests indicate that the SPI/ZrO₂‐15% membrane has good operation stability in the VRFB system. Copyright © 2014 John Wiley & Sons, Ltd.     

Si anode for next-generation lithium-ion battery

Si-based materials with high theoretical storage capacity and low working potential are one of the ideal anode materials for next-generation lithium-ion batteries, but their large volume change and low conductivity obstruct the commercial application. This article presents a brief overview of insights into charge–discharge mechanism and the main challenges of Si-based anodes in the past few years and outlines typical solving strategies, new mechanism, advanced characterization technology, and future directions.     

Fabrication of well‐aligned electrospun nanofibrous membrane based on fluorinated polyimide

We have fabricated novel nanofibrous fluorinated polyimide membranes on a specially designed collector, which is composed of conductive aluminum plates and glass insulator materials and can be removed from the apparatus, using an electrospinning method. We describe the structure and water flux properties of the nanofibrous fluorinated polyimide membranes. The electrospun nanofibers were deposited across the plates and uniaxially aligned to the collector. In addition, the multi‐layer stacked nanofibrous membranes, consisting of three‐dimensionally ordered nanopores, were produced. The pure water fluxes for the stacked membranes were measured, using a stirred dead‐end filtration cell, and were linearly decreased with an increasing deposition time, indicating that the nanopores formed in the nanofibrous membrane were further narrowed due to the regularly accumulated nanofibers. Copyright © 2009 John Wiley & Sons, Ltd.     

Photo-induced liquid crystal alignment on polyimide containing fluorinated groups

Polyimides were prepared from pyromellitic dianhydride, 4,4'-bis[2-(4-aminophenyl)hexafluoroprop-2-yl]diphenyl ether and 4,4'-diamodiphenyl ether (PMDA-BDAF-ODA) and used for liquid crystal alignment using linearly polarized UV exposure. The alignment properties of a LC on the polyimide films were found to depend on the fluorine content in the PMDA-BDAF-ODA alignment layer and on the UV exposure time. Pretilt angles were obtained in the range 0° to 90° dependent upon the fluorine content in the polyimide film and the UV exposure time. These effects seem to be closely related to the surface energy of the photo-alignment layer.     

Fluorinated solvents for high-voltage electrolyte in lithium-ion battery

Journal of Solid State Electrochemistry - The major obstacle for the application of high-voltage cathode materials is the anodic instability of the electrolyte. On the guidance of density...     

Photoreactive fluorinated polyimide protected by a tetrahydropyranyl group (THP) based on photo-induced acidolysis

A polyimide (6F-THP) with a tetrahydropyranyl group (THP) in its side chain has been synthesized. The THP group exhibits a high acidolysis rate in this polymer's film. This rate was faster than that of a tertbutoxycarbonyl group (t-BOC), which has been previously reported [1]. Furthermore, the deprotected fluorinated polyimide (6FDA-AHHFP) became soluble in an aqueous base due to the presence of a hydroxyl group attached to the phenyl group of the diamine segment. The polyimide thus provides high performance as a photopolymer when used in conjunction with a photoacid generator after the post-exposure baking process (PEB). The photoacid generators used in this study were p-nitrobenzyl-9,10-dimethoxyanthoracene-2-sulfonate (NBAS) and diphenyliodonium-9,10-dimethoxyanthoracene-2-sulfonate (DIAS). The quantum yields of photodissociation and photoacid generation were also measured. The photoacid-generating quantum yields closely corresponded to the photosensitivities of the photoreactive polyimide system. It was confirmed that the THP group was easily deprotected even in the 6F-THP film with p-toluenesulfonic acid as a model acid catalyst. The activation energy of the THP deprotection reaction was determined to be 12.8 kcal/mol (19.5 kcal/mol in the case of t-BOC). The relationships between the THP deprotecting rate constant (k_d) and acid molecular size and between k_d and polyimide structure were further investigated.     

Photoreactive fluorinated polyimide protected by tetrahydropyranyl (THP) group based on chemical amplification: Acid generation in polyimide film and lithographic properties

The photochemistry of photoacid generator (PAG), diphenyliodonium 9,10-dimethoxyanthracene-2-sulfonate (DIAS) and diphenyliodonium 8-anilinonaphthalene-1-sulfonate (DIANS) was investigated in both alkalinesoluble polyimide (6FDA-AHHFP) and novolak films. The quantum yields of photodissociation of DIAS and DIANS in both 6FDA-AHHFP and novolak films. The quantum yields of photodissociation of DIAS and DIANS in both 6FDA-AHHFP and novolak films were determined as 0.11, 0.21, 0.12 and 0.26, respectively. On the other hand, the quantum yields for acid generation from DIAS and DIANS in both of these films were 0.07, 0.18, 0.09 and 0.22, respectively, in the presence of an acid indicator. These results indicate that the values of the quantum yields of photodissociation and photoacid formation for DIAS and DIANS in 6FDA-AHHFP film are lower than those in novolak film. In order to elucidate the lowering of the quantum yields in 6FDA-AHHFP film, fluorescence quenchings of sodium 9,10-dimethoxy-anthracene-2-sulfonate and ammonium 8-anilinonaphthalene-1-sulfonate by a model compound of polyimide was carried out in acetonitrile. The fluorescences of these two salts were efficiently quenched by the model compound with the diffusion-controlled rate constant in acetonitrile, suggesting that a strong electron-accepting capability of the imide carbonyl group may hinder the electron transfer process within PAG molecules in 6FDA-AHHFP film. Although a polyimide (6F-THP) protected by tetrahydropyranyl group is insoluble in aqueous base, 6F-THP film containing PAG became soluble in a 2:1 mixture of 2.0 wt% tetramethylammonium hydroxide (TMAH) and methanol by exposure to 365 nm light and successive post-exposure baking (PEB) at 120°C for 10 min. The sensitivity and contrast of 6F-THP with DIANS after the PEB conditions mentioned above were 110 mJ/cm² and 3.7, respectively. A high-resolution pattern with a good profile was transferred into the 3 μm thickness of the 6F-THP film.     

PVDF-HFP/PMMA-coated PE separator for lithium ion battery

Microporous poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP)/poly(methyl methacryate) (PMMA)-coated polyethylene (PE) separators were prepared by a simple dip-coating process with various compositions of PVDF-HFP/PMMA mixture under 40% relative humidity condition. The results indicate that the porosity, liquid electrolyte uptake, and ionic conductivity of the coated separators are largely affected by a ratio of PVDF-HFP/PMMA mixture and the highest porosity, electrolyte uptake, and ionic conductivity can be achieved at a composition of PVDF-HFP/PMMA (5/5). The results of the cell performance tests also reveal that the PE separator coated with PVDF-HFP/PMMA in a ratio of 5:5 provides better rate capability and cycle stability than other PE separators coated with different ratios.     

A study on dielectric characteristics of fluorinated polyimide thin film

In this work, the effects of fluorination of polyimide thin films on surface and dielectric characteristics were studied using X-ray photoelectron spectroscopy (XPS) and dielectric spectrometry, respectively. The thermal and mechanical properties of the film were characterized by thermogravimetric analysis (TGA) and tensile strengths, respectively. The fluorine content of the polyimide thin film was increased with increasing treatment concentration, resulting in decreasing dielectric constant of the film. It was found that the replacement of fluorine led to the decrease of the local electronic polarizability of polyimide, or to the increase of the free volume, which can be attributed to the relatively large size of fluorine. Nevertheless, the fluorination did not significantly affect thermal or mechanical properties of the polyimide film under mild conditions in this system.     

Electrolyte additives for improved lithium-ion battery performance and overcharge protection

Much effort is being expended on the development of smart, safe, high-power lithium-ion batteries that are also environmentally friendly. Scaled-up lithium-ion batteries still raise safety concerns, especially when they are overcharged. Therefore, efforts continue to improve the thermal and chemical stability of positive electrodes, negative electrodes, separators, and electrolytes within the battery to counter thermal runaway. This opinion discusses highlights of research on additives for nonaqueous electrolytes published during 2018 and 2019.     

Flexible free-standing graphene-silicon composite film for lithium-ion batteries

Flexible, free-standing, paper-like, graphene-silicon composite materials have been synthesized by a simple, one-step, in-situ filtration method. The Si nanoparticles are highly encapsulated in a graphene nanosheet matrix. The electrochemical results show that graphene-Si composite film has much higher discharge capacity beyond 100 cycles (708 mAh g^? 1) than that of the cell with pure graphene (304 mAh g^? 1). The graphene functions as a flexible mechanical support for strain release, offering an efficient electrically conducting channel, while the nanosized silicon provides the high capacity.     

Flexible,fatigue resistant,and heat-insulated nanofiber-assembled polyimide aerogels with multifunctionality

Ultralight flexible polymers enable promising application in many fields but are often hindered by low reusability with fatigue failure, weak mechanical stability and low temperature resistance. Here, superelastic polyimide nanofiber aerogels (PNFAs) with high hydrophobicity have been prepared by utilizing the polyamic acid (PAA) nanofibers to construct a continuous and isotropic fibrous architecture. “Fiber-bonding” effect is designed to endow the PNFAs with the structure-derived superelasticity. The results demonstrate that the PNFAs possess ultralight densities (9.7–19.1 mg cm⁻³), excellent absorption capacity (58 times for n-hexane), broad working-temperature range, high resilience after 1000 fatigue cycles at 60% strain, and outstanding thermal insulation performance. Analysis of 50 absorption-harvesting cycle tests reveals that these highly hydrophobic PNFAs possess an ultrahigh reusability. The compressed PNFAs return to their original shape after they are distilled to recover the absorbed pollutants. These PNFAs with high absorption capacity and robust mechanical stability are promising to be applied in a variety of industrial and environmental applications.