Determination of polycyclic aromatic hydrocarbons in Diesel soot by high-performance liquid chromatography

Summary The described identification and determination of polycyclic aromatic hydrocarbons (PAH) in Diesel soot is based on a class-fractionation using an open Al₂O₃-column and a following separation on a reversed-phase HPLC-column with post-chromatographic derivatization. The optimized analysis has been applied to the determination of PAH in soots from different engines such as locomotives and motor vehicles by variation of the fuel additives and different Diesel/water emulsions. The results obtained by locomotives show that a special Diesel/water emulsion emits a minor amount of mutagenic and cancerogenic polycyclic aromatic hydrocarbons, whereas the emission of the comparatively harmless compounds like phenanthrene and benzo(h)quinoline increases.     

Comprehensive two-dimensional high-performance liquid chromatography for the separation of polycyclic aromatic hydrocarbons

A comprehensive two-dimensional HPLC system for the separation of polycyclic aromatic hydrocarbons was developed using a pentabromobenzyl column as the first dimension and two short monolithic C18 columns as the second dimension. The primary column and two secondary columns were coupled by a 10-port 2-position valve. The effluent from the first dimension was repetitively injected into the second dimension every 12 s. Due to its resolution, this technique is a powerful tool for the separation of polycyclic aromatic hydrocarbons in a complex matrix such as environmental samples.     

Determination of polycyclic aromatic hydrocarbons in water samples using high-performance liquid chromatography with amperometric detection

The determination of polycyclic aromatic hydrocarbons (PAHs) using high-performance liquid chromatography (HPLC) with UV and fluorescence detection has been well established. Although most of the PAHs can be detected by these methods, some environmentally important polyaromatic compounds, such as acenaphthylene, do not show fluorescence and can only be determined by UV detection at higher concentrations. A sensitive and selective determination of acenaphthylene, acenaphthene and the six PAHs listed in the TVO, the German drinking water standard, is also possible by amperometric detection following HPLC separation. The method was applied to the determination of PAHs in different water samples after solid-phase extraction (SPE). The efficiency of the amperometric determination was found to be superior to UV detection (λ = 300 nm).     

Determination of polycyclic aromatic hydrocarbons by high-performance liquid chromatography-particle beam-mass spectrometry

In this article, we report a high-performance liquid chromatography-particle beam-mass spectrometric (HPLC-PB-MS) method for the determination of polycyclic aromatic hydrocarbons (PAHs). The PB interface consists of a concentric ultrasonic nebulizer with temperature-controlled desolvation chamber and a three-stage momentum separator. The HPLCPB-MS method showed greater sensitivity for PAHs with molecular weights above 178 than for those PAHs with molecular weights below 178. The percent relative standard deviations for the determination of 0.5 ng chrysene, 1.0 ng dibenzo[a,h]anthracene, 1.0 ng benzo[g,h,i]perylene, and 2.5 ng coronene were 20%, 2.5%, 13.7%, and 6%, respectively. The detection limits at signal/noise = 3 were 0.2 ng for chrysene, 1.0 ng for dibenzo[a,h]anthracene, 0.5 ng for benzo[g,h,i]perylene, and 1.5 ng for coronene.     

Separation and identification of perchlorinated polycyclic aromatic hydrocarbons by high-performance liquid chromatography and ultraviolet absorption spectroscopy

High-performance liquid chromatography (HPLC) was coupled with ultraviolet absorption spectroscopy (UV) for the simultaneous separation and identification of a series of perchlorinated polycyclic aromatic hydrocarbons, such as perchlorobenzene (C6Cl6), perchloronaphthalene (C10Cl8), perchlorobiphenyl (C12Cl10), perchloroanthracene (C14Cl10), perchlorophenanthrene (C14C10), perchloroacenaphthylene (C12Cl8), perchloropyrene (C16Cl10) and perchlorofluoranthene (C16Cl10). HPLC was performed on an ODS column using methanol-hexane (80:20) as mobile phase at a flow-rate of 1.0 ml/min. UV absorption spectra of the elutes were detected in the region of 210-350 nm.     

Determination of some selected polycyclic aromatic hydrocarbons in environmental samples by high-performance liquid chromatography with fluorescence detection

Summary Analytical methods for the determination in environmental samples, of some selected Polycyclic Aromatic Hydrocarbons (PAH's), which are included on the EPA Priority Pollutant list, have been developed and evaluated. The methodology involves the extraction of PAH's from water samples by solvent extraction with dichloromethane. Solid samples were ultrasonically extracted with acetone/hexane and the extract was cleaned up on a silica gel/alumina column. The concentrated and cleaned up extracts were analysed by HPLC on a polymeric C₁₈ column using a gradient of acetonitrile/water as the mobile phase and fluorescence detection. Typical detection limits lie in the range of 1–30 ng ml^–1 of the analytes, but after sample pretreatment detection limits of 10–300 ng l^–1 were obtained. The extraction, clean-up and HPLC methodology was applied to the determination of selected PAH's in coal washings samples and the method was validated by the quantification of PAH's in a natural contaminated and a spiked sediment.     

Determination of hydroxylated polycyclic aromatic hydrocarbons in airborne particulates by high-performance liquid chromatography with fluorescence detection.

This paper describes a highly sensitive and selective method for the determination of hydroxylated polycyclic aromatic hydrocarbons (PAHs-OH) in airborne particulates. PAHs-OH were extracted from airborne particulates with ethanol by ultrasonication. The extractant was further cleaned up by solid phase extraction (SPE) with an aminopropylsilica cartridge, and subsequently analyzed by reversed-phase high-performance liquid chromatography with fluorescence detection. 2-Hydroxy-1-acetonaphthone was used as an internal standard. By the proposed method, 2-hydroxyfluorene and 1-hydroxypyrene were identified in airborne particulates and their concentrations were determined for the first time.     

Determination of polycyclic aromatic hydrocarbons in seawater by high-performance liquid chromatography with fluorescence detection following micelle-mediated preconcentration

In this work, the nonionic surfactant polyoxyethylene-10-lauryl ether has been used for the extraction and preconcentration of 14 polycyclic aromatic hydrocarbons, classified as priority pollutants by the US Environmental Protection Agency, from seawater samples. The cloud-point preconcentration previous separation by HPLC and quantification using fluorimetric detection and wavelength programming allow to determine these pollutants with detection limits ranging from 1.0 to 1.5 x 10(2) ng/l with RSDs better than 10.4%. The methodology is evaluated using well-established extraction and preconcentration methods and GC-MS.     

Molecular-shape recognition of polycyclic aromatic hydrocarbons in reversed phase liquid chromatography

Summary The molecular-shape recognition of polycyclic aromatic hydrocarbons has been studied on various stationary phases in reversed-phase high-performance liquid chromatography. The examined stationary phases were phenyl-, diphenyl-, triphenyl- and benzyl-bonded silicas. The results of regression analysis inidcated that triphenylsilica is the best packing material to recognize the difference in the molecular-shape of structural isomers. This fact was confirmed by the separation of 4-ring isomers.     

Quantification of several monohydroxylated metabolites of polycyclic aromatic hydrocarbons in urine by high-performance liquid chromatography with fluorescence detection

A high-performance liquid chromatographic method with fluorescence detection has been developed to determine the urinary polycyclic aromatic hydrocarbon metabolites 2-hydroxynaphthalene, 2-hydroxyfluorene, 9-hydroxyphenanthrene, 1-hydroxypyrene and 3-hydroxybenz[a]pyrene. Solid phase extraction (SPE) was used to clean up the samples, and washing with 30% methanol was found to be the best way to remove interferences in the matrix. The method detection limits ranged from 0.044 μg/L for 1-hydroxypyrene to 1.615 μg/L for 3-hydroxybenz[a]pyrene, and the recoveries ranged between 40% for 3-hydroxybenz[a]pyrene and 99% for 2-hydroxynaphthalene. The within-day relative standard deviation was lowest for 2-hydroxynaphthalene at 0.67% and went up to 2.42% for 3-hydroxybenz[a]pyrene, and the between-day relative standard deviation ranged from 3.84% for 9-hydroxyphenanthrene to 10.42% for 2-hydroxyfluorene. The correlation coefficients were between 0.9962 and 0.9998. The developed method was successfully used to analyze samples from student volunteers in a high school.     

Determination of polycyclic aromatic hydrocarbons in marine sediments by high-performance liquid chromatography after microwave-assisted extraction with micellar media

A simple and rapid method is developed for extraction and determination of polycyclic aromatic hydrocarbons (PAHs) in marine sediments. The procedure was based on the microwave-assisted extraction of PAHs in marine sediment samples using a micellar medium of Polyoxyethylene 10 lauryl ether as extractant. Two-level factorial designs have been used to optimize the microwave extraction process. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 85.70 and 100.73%, with a relative standard deviation of 1.77-7.0% for PAHs with a ring number higher than three.     

Retention characteristics of alkylated polycyclic aromatic hydrocarbons in normal phase liquid chromatography

Summary Retention characteristics of series of polymethyl and mono-n-alkyl derivatives of benzene and pyrene, and also of parent polycyclic aromatic hydrocarbons (PAH), were studied using silica and aminopropyl- and cyanopropyl-modified silica. Differences in the selectivities for the studied compound groups were found between the three phases. Deviations from linear behaviour in plots of log (k′)vs. carbon number were observed for the methyl series. These are explained in terms of differences in π-electron delocalisation within the aromatic ring systems. Further, the effect of methyl substitution on selectivity decreased with an increasing number of aromatic rings. Results were obtained which indicated that the primary adsorption site in a cyano column used in normal phase mode, at least for PAH molecules, is the cyano group.     

超高效液相色谱法检测土壤中的多环芳烃

采用二极管阵列(PDA)检测器,建立了超高效液相色谱(UPLC)定性定量分析土壤中16种多环芳烃(PAHs)的方法。并将该方法与传统高效液相色谱(HPLC)的分析性能进行了详细的比较。研究结果表明,采用UPLC法分析16种PAHs具有分析速度快(13.5 min)、检出限低(2～20 pg)、灵敏度高等优点。     

Heat capacities of liquid polycyclic aromatic hydrocarbons

Liquid heat capacities of 14 aromatic hydrocarbons were measured using a DSC calorimeter. Measurements were performed in the temperature range 100 K above the melting temperature of each hydrocarbon. The lowest and highest temperatures considered were respectively 303 and 692 K. Experimental results were correlated using Benson's group contribution approach. The group parameters determined allow the experimental results to be represented to within 2%.     

Screening and determination of polycyclic aromatic hydrocarbons in seafoods using QuEChERS-based extraction and high-performance liquid chromatography with fluorescence detection

A rapid, sensitive, and accurate method for the screening and determination of polycyclic aromatic hydrocarbons (PAHs) in edible seafood is described. The method uses quick, easy, cheap, effective, rugged, and safe (QuEChERS)-based extraction and HPLC with fluorescence detection (FLD). The method was developed and validated in response to the massive Deepwater Horizon oil spill in the Gulf of Mexico. Rapid and highly sensitive PAH screening methods are critical tools needed for oil spill response; they help to assess when seafood is safe for harvesting and consumption. Sample preparation involves SPE of edible seafood portions with acetonitrile, followed by the addition of salts to induce water partitioning. After centrifugation, a portion of the acetonitrile layer is filtered prior to analysis via HPLC-FLD. The chromatographic method uses a polymeric C18 stationary phase designed for PAH analysis with gradient elution, and it resolves 15 U.S. Environmental Protection Agency priority parent PAHs in fewer than 20 min. The procedure was validated in three laboratories for the parent PAHs using spike recovery experiments at PAH fortification levels ranging from 25 to 10 000 microg/kg in oysters, shrimp, crab, and finfish, with recoveries ranging from 78 to 99%. Additional validation was conducted for a series of alkylated homologs of naphthalene, dibenzothiophene, and phenanthrene, with recoveries ranging from 87 to 128%. Method accuracy was further assessed based on analysis of National Institute of Standards and Technology Standard Reference Material 1974b. The method provides method detection limits in the sub to low ppb (microg/kg) range, and practical LOQs in the low ppb (microg/kg) range for most of the PAH compounds studied.     

Determination of polycyclic aromatic hydrocarbons in edible oils and fats by on-line donor-acceptor complex chromatography and high-performance liquid chromatography with fluorescence detection

Various off-line methods for clean-up and sample enrichment are available for the analysis of polycyclic aromatic hydrocarbons (PAHs) in edible oils and fats. These methods consist of laborious and time consuming procedures. This study reports an on-line method using LC-LC coupling. After clean-up of the sample on a donor-acceptor complex chromatography (DACC) column the PAHs are transferred to and separated on an analytical HPLC column. Quantification is carried out with fluorescence detection. The DACC column clean-up is fast and is carried out during the HPLC run of the previous sample. Compared to the traditional methods this automated on-line method saves considerable time and significantly reduces the amount of solvent waste. The method uses common HPLC equipment and its performance has been evaluated.     

Thermodynamic and kinetic characterization of nitrogen-containing polycyclic aromatic hydrocarbons in reversed-phase liquid chromatography

A series of five nitrogen-containing polycyclic aromatic hydrocarbons (NPAHs) was studied on polymeric octadecylsilica using methanol and acetonitrile as the mobile phase. The thermodynamic and kinetic behavior was examined as a function of ring number, annelation structure, and position of the nitrogen atom. The retention factors for the NPAHs are smaller than those for the parent PAHs in methanol, while the converse is true in acetonitrile. The changes in molar enthalpy are relatively comparable in both mobile phases with 1-aminopyrene having values of -5.0 +/- 0.2 kcal/mol in methanol and -6.3 +/- 0.7 kcal/mol in acetonitrile (1 cal = 4.184 J). However, the rate constants from mobile to stationary phase (k(sm)) and from stationary to mobile phase (k(ms)) demonstrate large differences as a function of mobile phase. For example, the rate constants k(ms) for 1-aminopyrene and 4-azapyrene are 675 and 62 s(-1), respectively, in methanol at 303 K. In contrast, the same solutes demonstrate rate constants of 3.47 and 3.9 x 10(-3) s(-1), respectively, in acetonitrile. The activation energies for transfer from mobile phase to transition state (deltaE(double dagger(m)) and from stationary phase to transition state (deltaE(double dagger(s)) also differ as a function of mobile phase. For example, the activation energies deltaE(double dagger(s)), for 1-aminopyrene are 21 and approximately 0 kcal/mol, whereas those for 4-azapyrene are 19 and 23 kcal/mol, in methanol and acetonitrile, respectively. Based on these thermodynamic and kinetic results, the relative contributions from the partition and adsorption mechanisms are discussed.     

High-performance liquid chromatography determination of nitrated polycyclic aromatic hydrocarbons by indirect fluorescence detection

A high-performance liquid chromatography (HPLC) method for the analysis of nitrated polcyclic aromatic hydrocarbons (NPAHs) is reported. NPAH mixtures were pre-concentrated using solid-phase extraction and well resolved on a C(18) column. They were detected using an indirect method involving the quenching of the emission from the fluorophores 5,6,7,8-tetrahydronaphthol (5,6,7,8-THN-1-OH), 7-amino-4-methyl coumarin (Coumarin 120, COU-120) and 3-hydroxy-4-(2-hydroxy-4-sulfo-1-naphthylazo)2-naphthalene carboxylic acid (Calcon carboxylic acid, CCA). Linear calibration curves were obtained in the range 1.1 x 10(-9) to 1.1 x 10(-8) mol/L. Using COU 120 as the fluorophore, the detection limit was 2.9 x 10(-10) mol/L for 1-nitronaphthalene and 2.1 x 10(-11) mol/L for 2-nitrofluorene. Recoveries of NPAHs from spiked tap water samples were between 88 and 100%.     

Ultrasonication extraction coupled with magnetic solid-phase clean-up for the determination of polycyclic aromatic hydrocarbons in soils by high-performance liquid chromatography

C18-functionalized magnetic microspheres synthesized in a three-stage system and characterized by Fourier transform infrared (FTIR) spectroscopy and SEM were applied for clean-up and enrichment of polycyclic aromatic hydrocarbons (PAHs) in soil samples combined with ultrasonication extraction. Magnetic solid-phase extraction (MSPE) parameters, such as elution solvents, amounts of sorbents, enrichment time and organic modifier, were optimized together with ultrasonication time and extraction solvents. Under the optimal conditions, the developed method provided spiked recoveries of 63.2-92.8% with RSDs of less than 6.4% and limits of detection were 0.5-1.0 ng/g. This new method provides several advantages, such as high extraction efficiency, convenient extraction procedure and short analysis times. Finally, the method was successfully applied to the determination of polycyclic aromatic hydrocarbons in soil samples.     

Optimization of high-performance liquid chromatography and solvent parameters for the separation of polycyclic aromatic hydrocarbons compared with supercritical fluid chromatography with UV detection

Ten packed standard columns were evaluated for the separation of the sixteen US Environmental Protection Agency polycyclic aromatic hydrocarbons (PAHs) by gradient HPLC. This was done in a systematic way by the use of chemometric parameters such as window diagrams and chromatographic response factors and a computer program to calculate k′, , N and R_s. New approaches to a more economical and ecological use of HPLC solvents were evaluated. Good results were achieved by recycling acetonitrile-water waste by distillation as the azeotrope and using it again with methanol in an HPLC system. Supercritical fluid chromatography with carbon dioxide as supercritical fluid and acetonitrile as modifier was compared with HPLC, using the same column in both methods, for the determination of PAHs.