Thermodynamic analysis of preparation processes for boron-containing films with the use of N-trimethylborazine and hydrogen

The possibilities for using a minimization program for Gibbs energy functions (G _min) in multiphase multicomponent systems are illustrated. The process of chemical vapor deposition in a B-C-N-H-O system at reduced pressure (13.3 Pa) over a wide range of synthesis temperatures (300–1300 K) with the use of an initial gas mixture of N-trimethylborazine and hydrogen is modeled thermodynamically. The possibility of obtaining films of different compositions is shown, and the boundary conditions for the deposition of coatings of the general composition BC _x N _y are determined.     

Electrochemical studies on Zn deposition and dissolution in sulphate electrolyte

The electrochemical deposition and dissolution of Zn on Pt electrode in sulphate electrolyte was investigated by electrochemical methods in an attempt to contribute to the better understanding of the more complex Zn–Cr alloy electrodeposition process. A decrease of the Zn electrolyte pH (from 5.4 to 1.0) so as to minimise/avoid the formation of hydroxo-products of Cr in the electrolyte for deposition of alloy coatings decreases the current efficiency for the Zn reaction, but the rate of the cathode reaction increases significantly due to intense hydrogen evolution. The results of the investigations in Zn electrolytes with pH 1.0–1.6 indicate that Zn bulk deposition is preceded by hydrogen evolution, stepwise Zn underpotential deposition (UPD) and formation of a Zn–Pt alloy. Hydrogen evolution from H₂O starts in the potential range of Zn bulk deposition. Data obtained from the electrochemical quartz crystal microbalance (EQCM) measurements support the assumption that electrochemical deposition of Zn proceeds at potentials more positive than the reversible potential of Zn. Anodic potentiodynamic curves for galvanostatically and potentiostatically deposited Zn layers provide indirect evidence about the dissolution of Zn from an alloy with the Pt substrate. The presumed potential of co-deposition of Cr (−1.9 V vs. Hg/Hg₂SO₄) is reached at a current density of about 300 mA cm⁻².     

Structure of rhenium coatings obtained by CVD

By chemical vapor deposition in the hydrogen atmosphere from Re₂(CO)₁₀ and Re(CO)₃(Cp) on steel and ceramic (C/SiC) substrates, rhenium coatings are obtained with an average thickness of 3–13 μm, when Re₂(CO)₁₀ is used, and of 2–8 μm when depositing from Re(CO)₃(Cp). The coatings are studied by X-ray diffraction and scanning electron microscopy. It is shown that when Re₂(CO)₁₀ is used, an increase in the deposition temperature results in the growth of textured coatings with preferred orientation of crystallites in the [0 0 2] direction. At the same time, a tendency for decreasing the size of rhenium crystallites is observed. With the change of evaporator temperature, the structure of Re coatings obtained from Re(CO)₃(Cp) on steel substrates changes considerably: from compact non-layered without the obvious growth direction (T _evaporator = 120°C) to a three-layer structure, where the initial layer has a compact structure followed by columnar and powdered layers (T _evaporator = 110°C). A fine compact coating is formed on ceramic substrates at an evaporator temperature of 110°C.     

The effect of the water vapor pressure on the kinetics of thermal dehydration of manganese(II) formate dihydrate

The effect of the water vapor pressure on the thermal dehydration of manganese(II) formate dihydrate was studied by means of isothermal gravimetry under various water vapor pressure, ranging from 4.6 to 24.4 torr. The kinetics of dehydration was described by a two-dimensional phase-boundary model,R ₂. The rate of dehydration decreased with increasing atmospheric water vapor pressure, but the Smith-Topley phenomenon was not observed for the present dehydration. The activation energy and the frequency factor for the dehydration were 110–170 kJ·mol⁻¹ and 10¹⁰–10¹⁶ cm·s⁻¹, respectively. These values increased with increasing water vapor pressure, and were much larger than those reported for the dehydration in vacuum.     

Investigation of the interaction between Co sulfide coatings and Cu(I) ions by cyclic voltammetry and XPS

The interaction between the Co sulfide coating formed on a glassy carbon electrode and Cu(I)-ammonia complexes solution was investigated by cyclic voltammetry in 0.1 M KClO₄, 0.1 M NaOH and 0.05 M H₂SO₄ solutions. It was determined that, after treating the cobalt sulfide coating formed by two deposition cycles with Cu(I)-ammonia complexes (0.4 M, pH 8.8–9.0, τ=180 s, T=25±1°C), an exchange occurs between the coating components and Cu(I). Copper(I) substitutes 75% of the Co(III) compounds present in the coating (~1.81×10^–7 mol cm^–2) because of Cu₂O (1.36×10^–7 mol cm^–2) formation. The rest of the Co(II) and Co(III) sulfide compounds are also replaced by copper with formation of Cu_{2– x} S with a stoichiometric coefficient close to 2 (~1.9). After modifying the cobalt sulfide coatings with Cu(I) ions, the total amount of metal (Co+Cu) increases, owing to the sorption of Cu(I) compounds. In addition, the number of deposition cycles decreases from 3 to 1.5 [1 cycle involves cobalt sulfide layer formation and 0.5 cycle is attributed to modifying by Cu(I) ions]. The coatings modified in the above-mentioned manner may be successfully used for plastic electrochemical metallization as Cu_{2– x} S coatings formed by three deposition cycles. Electronic Publication     

Synthesis of a fluorescein–porphyrin hybrid and its supramolecular self-assembly with amino-porphyrinatocopper(II) by hydrogen bonding

A fluorescein–porphyrin hybrid (Fl-PTPP) has been synthesized and characterized by UV/Vis, IR, ¹H NMR, ES-MS and elemental analysis. The supramolecular self-assembly of Fl-PTPP with the copper(II) complex of 5-(p-amino-phenyl)-10,15,20-triphenylporphyrin, (CuAPTPP), by hydoxyl-amino type hydrogen bonding was studied using vapor pressure osmometry (VPO) measurements, ES-MS, UV/Vis, ¹H NMR and fluorescence spectroscopic titration. The data indicate formation of a (Fl-PTPP)–CuAPTPP supramolecular complex. Fluorescence strengthening character was observed in a spectroscopic titration experiment for the Fl-PTPP/CuAPTPP system. The association constant of the supramolecular complex was calculated from the fluorescence titration data, and found to be less than that of a carboxyl–carboxyl type hydrogen-bonding system.     

Sampling and determination of hydrogen cyanide in cigarette smoke

A method for sampling and determination of hydrogen cyanide in cigarette smoke is described. Cigarette smoke is filtered through a glass fiber filter paper, and only gaseous compounds, such as hydrogen cyanide, are collected in a dilute sodium hydroxide solution. The cyanide is determined spectrophotometrically at 550 nm by the isonicotinic acid–pyrazolone method. Maximum absorbance is achieved within 10 min at room temperature, and remains constant for about 20 min. Beer’s law is obeyed in the range 0.04∼0.80 μg mL^–1 cyanide, with a molar absorptivity of 3.48 × 10⁴ L mol^–1 cm^–1. Received: 30 November 1998 / Revised: 21 April 1999 / Accepted: 30 April 1999     

Sampling and determination of hydrogen cyanide in cigarette smoke

A method for sampling and determination of hydrogen cyanide in cigarette smoke is described. Cigarette smoke is filtered through a glass fiber filter paper, and only gaseous compounds, such as hydrogen cyanide, are collected in a dilute sodium hydroxide solution. The cyanide is determined spectrophotometrically at 550 nm by the isonicotinic acid–pyrazolone method. Maximum absorbance is achieved within 10 min at room temperature, and remains constant for about 20 min. Beer’s law is obeyed in the range 0.04∼0.80 μg mL^–1 cyanide, with a molar absorptivity of 3.48 × 10⁴ L mol^–1 cm^–1. Received: 30 November 1998 / Revised: 21 April 1999 / Accepted: 30 April 1999     

Hydrogen peroxide induced formation of peroxystannate nanoparticles

Stable, amorphous potassium peroxystannate nanoparticles of controlled average size—in the range 10–100 nm—and of controlled hydrogen peroxide content—in the range of 19–30 wt%—were synthesized by hydrogen peroxide induced polymerization in water–potassium hexahydroxostannate solutions. The sol phase and the precipitate were characterized by vibrational spectroscopies, ¹¹⁹Sn NMR, XPS and XRD using crystalline K₂Sn(OH)₆ and K₂Sn(OOH)₆ reference materials. This is the first study to show that peroxocoordination induces polymerization of a main group element. ¹¹⁹Sn NMR studies show that peroxotin coordination and polymerization took place already in the hydrogen peroxide–water phase. The high abundance of peroxotin bonds revealed by ¹¹⁹Sn MAS NMR, vibrational spectroscopy, and XPS suggests that the particles are predominantly made of peroxo bridged tin networks. Although the particles are highly stable in the dry phase as well as in alcohol solutions and do not lose hydrogen peroxide upon storage, they release their stored hydrogen peroxide content by exposure to water.     

Structural,optical and secondary electron emission properties of diamond like carbon thin films deposited by pulsed-DC plasma CVD technique

Plasma enhanced chemical vapor deposition (PECVD) technique using pulsed-DC power supply was used to fabricate diamond like carbon (DLC) films at deposition rates as high as 110 nm/min. The DLC films deposited by pulsed-DC and DC based power supplies under different gas flow ratios were studied for their suitability as dielectric layer coatings in plasma display panels (PDPs). The effect of deposition parameters on the properties of the DLC films were studied using Fourier transform infra-red spectroscopy (FTIR) and spectroscopic ellipsometry (SE). FTIR reveals that higher hydrogen dilution in gas mixture leads to higher sp³ content. SE studies in wide spectral range were analyzed using Tauc-Lorentz model dielectric function. A rise in the extracted refractive index was seen on increasing the H₂ content in the feed gas, thus resulting in optically denser films. Secondary electron emission coefficient (γ) was measured in the films deposited by the DC and pulsed-DC based PECVD. Firing voltage in the DLC samples was found to have very low variation in the operating pressure range used in commercial PDPs, suggesting possibility of enhanced long term reliability of DLC coatings in future PDP applications.     

Changes of the Cu electrode real surface area during the process of electroless copper plating

The surface area (nanoscale roughness) of copper coatings deposited from electroless plating solutions containing Quadrol, L(+)- and DL(∓)-tartrate as Cu(II) ion ligands was measured using underpotential deposition thallium monolayer formation. Surface roughness of Cu coatings depends on the plating solution pH and the Cu(II) ligand, and varies over a wide range. In L(+)-tartrate and Quadrol solutions (pH 12.5–13.3) the roughness factor R _f is low and is equal to 2–3 and 4–6, respectively (substrate: electrodeposited Cu; R _f=2.2). Cu coatings of higher surface area are obtained in DL(∓)-tartrate (pH 12.3–12.7) and Quadrol (pH 12.0) solutions: R _f reaches 20–30. The correlation between R _f and Cu deposition rate was found in L(+)-tartrate solution. The Cu surface area changes are discussed in terms of partial electrochemical reactions of the autocatalytic Cu deposition process, and the decisive role of cathodic Cu(II) reduction from adsorbed Cu(II) complex species. Received: 2 November 1999 / Accepted: 22 February 2000     

Resonance light-scattering method for the determination of BSA and HSA with sodium dodecyl benzene sulfonate or sodium lauryl sulfate

A new resonance light-scattering (RLS) assay of proteins such as bovine serum albumin (BSA) and human serum albumin (HSA) is presented. In the medium of phosphoric acid (pH=2.6), the weak RLS of sodium dodecyl benzene sulfonate (SDBS) or sodium lauryl sulfate (SLS) can be greatly enhanced by proteins, owing to interaction between the protein and the anionic surfactant and formation of an associate. The RLS intensity of the SDBS–protein system is stronger than that of the SLS–protein system under same experimental conditions. It is considered that the synergistic resonance caused by the absorption of both protein and SDBS could produce strong RLS, while absorption of protein only in the SLS system could cause relatively weak RLS. The enhanced intensity of RLS is proportional to the concentration of the protein. If SDBS is used as the probe the linear range is 7.5×10^–9–1.5×10^–5 g mL^–1 for BSA and 1.0×10^–8–1.0×10^–5 g mL^–1 for HSA. The detection limits are 1.8 and 2.8 ng mL^–1, respectively. When SLS is used as the probe the linear range is 2.0×10^–8–1.0×10^–5 g mL^–1 and 2.5×10^–8–1.0×10^–5 g mL^–1 for BSA and HSA, respectively, and the detection limits are 12.8 and 21.6 ng mL^–1, respectively. The biological mimics samples are synthetic concoctions of BSA and HSA with some interferents. In these samples, the concentration of interferents is higher than the concentration normally existing in organisms. The samples were determined satisfactorily.     

Moderate-temperature reduction of copper chromite by hydrogen and hydrogen desorption from the surface of reduced chromite

The reduction of copper chromite CuCr₂O₄ by hydrogen at 300–573 K and a hydrogen pressure of 4×10⁴-8 × 10⁴ 10⁴ Pa and hydrogen desorption from the surface of a reduced sample are studied. The rate of copper chromite reduction becomes high at temperatures above 473 K. Hydrogen desorbs from the surface of metallic copper covering the surface of chromite during its reduction. The heat of hydrogen adsorption on the metallic copper is almost independent of the surface coverage, 70–80 kJ/mol.     

Diamond-like carbon films for polyethylene femoral parts: Raman and FT-IR spectroscopy before and after incubation in simulated body liquid

In artificial prosthetics for knee, hip, finger or shoulder joints, ultrahigh molecular weight polyethylene (UHMW-PE) is a significant material. Several attempts to reduce the wear rate of UHMW-PE, i.e. the application of suitable coatings, are in progress. A surface modification of polyethylene with wear-resistant hydrogenated diamond-like carbon is favourable, owing to the chemical similarity of polyethylene (–C–H₂–) _n and C:H or amorphous C:H (a–C:H) coatings with diamond-like properties. In the present study, the microstructure of a–C:H coatings on UHMW-PE substrates was investigated by Raman and Fourier transform infrared (FT-IR) spectroscopy. FT-IR spectroscopy shows very broad absorption lines, which point to the disorder and diversity of different symmetric, asymmetric aromatic, olefin sp ²-hybridized or sp ³-hybridized C–H groups in the amorphous diamond-like carbon coating. Following a long incubation of 12 months in a simulated body liquid, the structural investigations were repeated. Furthermore, fractured cross-sections and the wetting behaviour with polar liquids were examined. After incubation in simulated body liquid, Raman spectroscopy pointed to a reduction of the C–H bonds in the diamond-like carbon coatings. On the basis of these findings, one can conclude that hydrogenated diamond-like carbon is able to interact with salt solutions by substituting the hydrogen with appropriate ions.     

Synthesis of tungsten oxides with cellular structure

Being exposed to hydrochloric acid vapor, solutions of a surfactant and sodium tungstate form tungstic-acid-based materials with a structure representing a system of interpenetrating hollow spheres 2–8 μm in diameter constructed from lamellar H₂WO₄ crystals with a thickness of 80–200 nm. The reduction of the tungstic-acid-based material with hydrogen gives rise to the formation of a material based on tungsten(IV) oxide (WO₂), which retains the initial structure. The adsorption capacity of the tungstic-acid-based materials is determined with respect to benzene. The specific surface area of the obtained materials is 60–110 m²/g.     

Development of Passive and Active Barrier Coatings on the Basis of Inorganic–Organic Polymers

Summary. With a new kind of barrier coating material, namely inorganic–organic polymers, it is possible to obtain excellent barrier properties against oxygen, water vapor, and flavor permeation. These hybrid polymers can be synthesized by the sol–gel technique. If extremely low permeation values are needed, the combination of hybrid polymer coatings with thin inorganic oxidic layers (SiO_x, AlO_x) is very effective and leads to permeation values for oxygen and water vapor below 10⁻³ cm³/m² · d · bar or g/m² · d. These passive barrier layers can be further improved by the combination with active oxygen barrier layers which have been developed for the food packaging industry. This approach makes these multilayer laminates promising candidates for special applications in the food packaging industry as well as for sophisticated applications in technical areas: the encapsulation of sensitive organic devices like solar cells, organic light emitting diodes, or polymer electronic systems.     

An electroanalytical study of the drug proflavine

A square wave adsorptive stripping voltammetric (SWAdSV) method was developed for the determination of proflavine. The electrochemical behaviour of proflavine was investigated by cyclic (CV) and square wave voltammetry (SWV) at the hanging mercury drop electrode (HMDE) and carbon paste electrode (CPE). Different parameters were tested to optimize the conditions of the determination. Better results were obtained by square wave voltammetry using CPE where two oxidation and a reduction peak, appeared, at 0.19, 0.94 and 0.20 V, respectively. The peak at 0.19 V is quasi-reversible and deposition dependent. Linearity was observed in the range of (0.2–23.4) × 10⁻⁸ M (r = 0.998) during the anodic scan and in the range of (1.17–117) × 10⁻⁸ M (r = 0.999) during the cathodic scan. The second peak at 0.94 V is irreversible and deposition independent. The linearity of this peak was observed in the range of (1.29–11.7) × 10⁻⁸ M (r = 0.998). The method was applied to the analysis of bovine serum and gave satisfactory results. Correspondence: S. Th. Girousi, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University, Thessaloniki 54124, Greece     

Simple spectrophotometric method for the determination of sulfur dioxide by its decolorizing effect on the peroxovanadate complex

A simple, rapid, and economical spectrophotometric method is developed for the determination of sulfur dioxide in sugar and air samples. The developed method is based on a red-brown peroxovanadate complex (λ_max = 470 nm) produced in 2 M sulfuric acid when ammonium metavanadate is treated with hydrogen peroxide. Under fixed concentrations of hydrogen peroxide and ammonium metavanadate, when sodium metabisulfite (Na₂S₂O₅ = 2SO₂) is added, it preferentially reacts with hydrogen peroxide producing sulfuric acid, and the unreacted hydrogen peroxide then reacts with ammonium metavanadate; therefore, the concentration of sulfur dioxide is directly proportional to a decrease in the concentration of the peroxovanadate complex. The stoichiometric ratio between hydrogen peroxide and ammonium metavanadate as well as the stability constant of the complex are determined by the modified Job’s method and the respective values are found to be 1: 1 and 2.5 × 10⁴ mol⁻¹ L, respectively. The system obeys Lambert-Beer’s law in the concentration range 3.57–64.26 ppm of sulfur dioxide. The molar absorptivity, correlation coefficient, and Sandell’s sensitivity values are found to be 0.649 × 10³ L mol⁻¹ cm⁻¹, 0.9908, and 0.1972 μg cm⁻², respectively. The method is applied to the determination of sulfur dioxide present in commercial sugars and air samples. The results obtained are reproducible with a standard deviation of 0.02–0.05. For method validation, sulfur dioxide is also determined separately following the AOAC method for an air sample and the ICUMSA method for commercial sugars. The results obtained by the developed and official methods are in good agreement. The text was submitted by the authors in English.     

A hydrogen peroxide biosensor based on direct electrochemistry of hemoglobin in palladium nanoparticles/graphene-chitosan nanocomposite film

Thermally two-dimensional lattice graphene (GR) and biocompatibility chitosan (CS) act as a suitable support for the deposition of palladium nanoparticles (PdNPs). A novel hydrogen peroxide (H₂O₂) biosensor based on immobilization of hemoglobin (Hb) in thin film of CS containing GR and PdNPs was developed. The surface morphologies of a set of representative membranes were characterized by means of scanning electron microscopy and showed that the PdNPs are of a sphere shape and an average diameter of 50 nm. Under the optimal conditions, the immobilized Hb showed fast and excellent electrocatalytic activity to H₂O₂ with a small Michaelis–Menten constant of 16 μmol L⁻¹, a linear range from 2.0 × 10⁻⁶ to 1.1 × 10⁻³ mol L⁻¹, and a detection limit of 6.6 × 10⁻⁷ mol L⁻¹. The biosensor also exhibited other advantages, good reproducibility, and long-term stability, and PdNPs/GR–CS nanocomposites film would be a promising material in the preparation of third generation biosensor.     

Influence of pulse parameters on nanocrystalline zinc coatings electrodeposited from acidic sulfate electrolyte

The influence of pulse electrodeposition parameters (i.e., current-on time, current-off time and peak current density) on the grain size and orientation of zinc deposits was investigated in acidic sulfate electrolyte. The scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses indicate that the pulse parameters play an important role in the grain refinement of nanocrystalline zinc coatings. As varying peak current density (1–2 A/cm²), current-on time (1–6 ms) and current-off time (4–18 ms), nanocrystalline zinc coatings are produced in the grain range 60 to 35 nm. The pulse parameters have a slight influence on the orientation of nanocrystalline zinc coatings. Published in Russian in Elektrokhimiya, 2009, vol. 45, No. 3, pp. 310–315. The article is published in the original.