MoS_2/TiO_2复合催化剂的制备及其在紫外光下的光催化制氢活性

为了研究复合光催化剂在光催化中的制氢效率,采用水热法制备了Mo S2纳米片,然后通过水热法在Mo S2纳米片上负载了TiO_2纳米颗粒,形成了Mo S2/TiO_2异质结复合催化剂。采用冷场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)、拉曼光谱(Raman),X射线光电子能谱(XPS)对材料的结构和光学性能表征并进行分析。通过光催化制氢测试对光催化剂进行评价,实验结果表明,在波长为365 nm的紫外光照射下,最高光催化制氢速率为1004μmol·h-1·g-1,对应的催化剂的Mo S2含量为30%,其催化速率远大于单一的Mo S2和TiO_2,表明Mo S2/TiO_2复合催化剂在紫外光照下能显著提高光催化产氢性能。基于Mo S2/TiO_2复合光催化剂优越的光催化产氢性能,本文对复合光催化剂的产氢机理做了研究和分析。     

简单浸渍法制备纳米CuO/TiO2及其光催化剂活性

以Cu(NO₃)₂·3H₂O和P25为前躯体,通过简单浸渍法制备了CuO/TiO₂光催化剂,利用N₂物理吸附、XRD、TEM、UV-vis漫反射光谱分析了催化剂的结构特性。研究了Cu组分的负载量、催化剂在反应液中的分散量、催化剂焙烧温度、反应液中甲醇浓度对CuO/TiO₂光催化反应产氢活性的影响,并考察了催化剂的稳定性,提出了该体系光催化反应的机理。结果表明,Cu的适宜负载量为2.0%~7.5%(质量分数),在Cu质量分数2.0%、催化剂焙烧温度350℃、甲醇的体积浓度为10%、催化剂分散量为1.0 g/L时,产氢活性可达到1 022 μmol/(h·g),并且该催化剂具有较好的稳定性。     

A rapid and simple microwave-assisted digestion procedure for spectrophotometric determination of titanium dioxide photocatalyst on activated carbon

Deposition of titanium dioxide (TiO₂) on activated carbon (AC) surface has been widely utilized for the production of TiO₂/AC photocatalyst, which can be used in photo-degradation of pollutants. In this work, a fast and simple digestion procedure has been developed for the spectrophotometric quantitative analysis of TiO₂ in TiO₂/AC photocatalyst. Microwave-assisted digestion was used in the procedure. The microwave-digestion procedure was optimized using the single-variable method. Variables optimized included time of ashing, effective digestion time, volume and concentration of sulfuric acid, effect of adding a digestion catalyst, effect of sample pulverizing and on–off time cycle of the microwave. The analysis was completed spectrophotometrically after addition of hydrogen peroxide to the digested solution. Procedure precision and accuracy was tested by application to photocatalyst samples containing known amounts of TiO₂, and compared with previously published spectrophotometric procedures. The proposed microwave procedure was capable of recovering 98.4–101.1% of TiO₂ in the catalyst in less than 10 min, without the need for sample ashing. Analytical precision is 1.42–2.39% relative standard deviation (R.S.D.). In terms of accuracy and precision, the proposed microwave procedure was comparable with other procedures, but the proposed microwave procedure was superior in terms of shorter procedure duration.     

A New Strategy for Improving the Efficiency of Low-temperature Selective Catalytic Reduction of NOx with CH4 via the Combination of Non-thermal Plasma and Ag2O/TiO2 Photocatalyst

In the present work, a remarkable combination of non-thermal plasma and photocatalyst was developed to widen the operating temperature window of selective catalytic reduction(SCR) of NO_x with CH₄, especially to improve the low-temperature removal efficiency of NO_x. It was shown that the operating temperature window was significantly widened. Among all the catalysts prepared, 1%Ag₂O/TiO₂ showed the highest catalytic activity for NO_x removal due to the utilization of near ultraviolet light. The conversion of NO_x to N₂ over the in-plasma 1%Ag₂O/TiO₂ photocatalyst at 60 and 300℃ could achieve 31.8% and 53.0%, respectively. The combination mode of plasma and catalyst affected NO_x removal efficiency greatly, the in-plasma catalysis outperformed the post-plasma catalytic mode remarkably, signifying the contribution of photocatalytic processes on the catalysts. Meanwhile, the characterizations of the catalyst demonstrated that the morphology and structure of the Ag₂O/TiO₂ catalyst were unchanged throughout the non-thermal plasma and photocatalytic processes, implying the superior stability of the catalyst.     

Pt/TiO2纳米纤维的制备及其对甲醇的电催化氧化活性

采用静电纺丝技术结合还原浸渍法制备了Pt/TiO₂纳米纤维电催化剂, 通过X射线衍射(XRD)分析、扫描电镜(SEM)、透射电镜(TEM)和X射线能谱(EDS)等测试手段对样品的晶相、形貌、微结构和化学组成进行了表征. 测试结果表明, TiO₂纳米纤维为锐钛矿和金红石组成的混晶, Pt 纳米颗粒均匀地分布于TiO₂纳米纤维的表面, 且Pt 颗粒大小较均一, 平均粒径为4.0 nm, Pt/TiO₂纳米纤维中Pt 的质量分数约为20%. 采用三电极体系的循环伏安和计时电流电化学分析方法研究了样品在酸性溶液中对甲醇的电催化氧化活性, 结果表明, 与负载相同质量分数Pt 的Pt/P25 和商业Pt/C 催化剂相比较, Pt/TiO₂纳米纤维催化剂对甲醇呈现出较高的电催化氧化活性和更好的稳定性.     

新型核壳Ag@AgSeX纳米粒子析氢助剂:原位表面硒化以提升TiO2的光催化产氢活性

纯相光催化材料的产氢性能主要受限于较低的电荷分离效率和缓慢的界面催化反应速率.表面负载助催化剂因其能够实现快速转移光生电子和提供界面催化活性中心被认为是促进电荷分离和提升界面催化反应的有效手段.贵金属类材料,尤其是金属铂(Pt),被认为是光催化产氢领域的理想助剂,但储量低和价格昂贵严重制约了其大规模实际应用.因此,发展...     

Z型g-C3N4/Pt/TiO2纳米管阵列复合电极的制备及光电氧化甲醇性能

以NH₄Cl为气体模板吹制双氰胺制备g-C₃N₄纳米片, 并将其负载于Pt/TiO₂纳米管阵列(Pt/TiO₂ NTs)上, 制备了一种新型的Z型g-C₃N₄/Pt/TiO₂NTs复合电极材料. 通过扫描电子显微镜、 X射线衍射和X射线光电子能谱对该材料的结构进行了表征, 采用电化学和光电化学方法研究了材料的性能. 研究结果显示, 在可见光照射下, g-C₃N₄/Pt/TiO₂ NTs复合材料具有高效的光电氧化甲醇的性能. 该复合材料的高性能主要归因于以下两点： (1) g-C₃N₄与Pt/TiO₂NTs的结合有效扩展了其在可见光范围的吸收; (2) Z型电荷转移保留了具有强氧化能力的空穴和强还原能力的电子, 从而使光生中间体作用于电催化过程增强了甲醇氧化效率.     

太阳光照射浮石负载二氧化钛降解氨氮废水

采用溶胶-凝胶法制备了Ti O_2,并使Ti O_2负载在浮石上制备Ti O_2/浮石光催化剂。用X射线荧光光谱(XRF)、电镜扫子显微描(SEM)和傅里叶红外光谱(FT-IR)表征浮石、Ti O_2及Ti O_2/浮石。在太阳光照射下,用Ti O_2/浮石处理模拟氨氮废水,以废水中氨氮降解率为标准,考察影响氨氮降解因素。结果表明,Ti O_2成功固定在浮石表面,负载率为3.71%;废水中氨氮降解率随太阳光照射时间、废水p H值、催化剂Ti O_2/浮石含量增加而增大。当初始氨氮浓度为500 mg/L、太阳照射180 min、废水p H=11、催化剂Ti O_2/浮石剂量为20 g/L时,氨氮降解率达82.0%,氨氮除去率86.8%,降解产物中未发现污染成分NO_2~-和NO_3~-产生。催化剂再生/催化3次,每次再生后氨氮降解率约下降10.0%。该方法快速、简单、低消耗和产生二次污染少,能有效地降解废水中的氨氮。     

Hydrothermal Synthesis of H3PW12O40/TiO2 Nanometer Photocatalyst and Its Catalytic Performance for Methyl Orange

H3PW12O40/TiO2 nanometer photocatalyst was prepared by one step hydrothermal synthesis from H3PW12O40′nH2O and Ti(OBu)4,simultaneously realizing the load and modification of H3PW12O40.The catalyst was ...     

TiO_2-Al_2O_3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO2-Al2O3复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备.通过N2吸附(BET)、X射线衍射(XRD)、透射电镜(TEM)、程序升温还原(TPR),X射线光电子能谱(XPS)和等离子体发射光谱(ICP-AES)表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能.结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al2O3的孔特征,具有较大的比表面积和较宽的孔分布,TiO2主要以表面富集的形式分散在管状的γ-Al2O3表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni2P和Ni12P5;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO2趋于在块状的Al2O3表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni2P.不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n(Ti)/n(Al)=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340℃,3 MPa,氢油体积比500,液时空速3 h-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

The Structure and Properties of Mesoporous TiO2 Film Photocatalyst

As a good photocatalyst, TiO₂ has a promising prospect in environmental purification^[1]. Due to the technical problem for the separation of dispersed TiO₂ nanosized catalyst, TiO₂ film photocatalyst has become a better choice for TiO₂ photocatalyst used in fluid^[2]. Because TiO₂ thin film photocatalyst has small surface area, the catalytical activity was very low. It was an effective way to use mesoporous TiO₂ film with high surface area as photocatalyst. The structure and properties of mesoporous TiO₂ film was studied here.     

Decomposition of toluene using an atmospheric pressure plasma/TiO2 catalytic system

Application of atmospheric pressure plasma as an alternative technology for the destruction of toluene is demonstrated in this study. Used TiO₂ colloidal solution was obtained by an improved sol–gel method, and coated on glass beads to prepare decomposition of toluene. The physical property of synthesized TiO₂ catalyst film was analyzed by XRD and SEM spectroscopy. From these results, it was identified that the catalyst film exhibited anatase structure with particle size of about 50–100 nm after calcination at 500 °C for 1 h. The decomposition of toluene in TiO₂/O₂ plasma system was investigated. Amounts of the catalyst and toluene concentration were fixed as 3 wt.% and 1000 ppm, respectively. The analyses for performance of toluene decomposition and intermediates in reaction were done by the in situ method using the mass spectroscopy and gas chromatography. The toluene of 40% was decomposed at pulse voltage of 13 kV in the only O₂ plasma condition without TiO₂ catalyst. Furthermore, the conversion enhanced remarkably in the TiO₂/O₂ plasma system, and it reached 70% at pulse voltage of 13 kV after 120 min. This result was very notable compared with that in photocatalytic system, with below 40% after 120 min reaction.     

一步法制备二氧化钛-金复合材料及其光解水制氢性能

以钛粉为还原剂,氯金酸为氧化剂,将二者在180 ℃水热反应釜中发生氧化还原反应,最终生成直径800 nm左右的TiO₂,比表面积为3.5 m²/g左右,其表面均匀担载了直径20 nm左右的金纳米颗粒。 采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、X射线光电子能谱分析(XPS)、紫外可见漫反射光谱、光电流密度、光催化制氢性能等测试表征了该复合催化剂的结构及性能。 结果表明,一步法制备的复合催化剂形貌规整,TiO₂为锐钛矿晶型,金纳米颗粒的局域表面等离子体共振(LSPR)作用促进了催化剂对可见光有较强的吸收,催化剂催化产氢性能伴随金含量增大存在先增后减规律,可见光下最大产氢速率为0.1 μmol/(g·h),光催化活性表现稳定。     

低温等离子体协同Cu-Mn-Ce-Zr/TiO2催化降解甲苯

以TiO₂为载体,采用等体积浸渍法制备了负载型Cu_xMn_1-xCe_0.75Zr_0.25/TiO₂(x=1.0、0.75、0.5、0.25、0)负载型催化剂,采用XRD、H₂-TPR、O₂-TPD和XPS等方法对催化剂进行了表征,并通过低温等离子体协同催化剂对大流量的甲苯模拟废气进行了催化降解反应研究。结果表明,Cu和Mn单主金属催化剂的活性优于Cu-Mn双主金属催化剂,其原因是双金属催化剂中Mn的添加减弱了Cu与助剂Ce之间的相互作用,使得催化剂的晶格氧减少,低温还原性能降低。在反应初期,甲苯降解主要依赖于催化剂的活性,具有较好的低温还原性以及丰富的氧空穴和晶格氧含量的CuCe_0.75Zr_0.25/TiO₂的活性最好;Mn具有较强的O₃分解能力,当等离子体比能密度(SED)增加到一定值后,等离子体与催化剂的协同作用增强,从而使得MnCe_0.75Zr_0.25/TiO₂催化剂活性高于CuCe_0.75Zr_0.25/TiO₂,强化了甲苯的脱除。     

C/Cr2O3/TiO2复合材料的制备及其光催化性能研究

本文以制革含铬革屑为原材料,基于矿物鞣剂复鞣的原理,将Ti(IV)均匀、稳定地负载到含铬革屑上,在氮气氛围下,经高温热解制备得到C/Cr₂O₃/TiO₂光催化剂,并研究了其对四环素(TC)的光催化降解效果及机理。结果表明,C/Cr₂O₃/TiO₂光催化剂具有明显的介孔结构,比表面积较大,为277.47 m²·g^-1,Cr₂O₃和TiO₂已实现复合并负载在生物炭(C)上。通过光催化降解发现,在模拟自然光照下,当催化剂用量为0.04 g,TC初始浓度为50 mg·L^-1,溶液pH为2时,TC的去除率可高达99.99%。结合自由基捕获实验发现,C/Cr₂O₃/TiO₂光催化剂对TC的降解作用主要依靠反应体系中产生的大量·O₂^-,·OH和h⁺。     

Keggin型铬取代的磷钨杂多阴离子/二氧化钛纳米膜光催化剂的制备及可见光催化性能

以钛酸四丁酯Ti(OC₄H₉)₄为TiO₂前驱体,Keggin型铬取代的杂多阴离子PW₁₁Cr为可见光活性组分,采用溶胶-凝胶提拉法在玻片表面制备了PW₁₁Cr/TiO₂纳米膜光催化剂,并用UV-Vis DRS、IR、XRD、SEM和TEM等技术手段对催化剂的光吸收性质、化学组成、晶相和表面结构形貌等进行了表征;讨论了膜中PW₁₁Cr和TiO₂相互作用的方式;以染料模型污染物RhB的可见光催化降解为探针,评估了PW₁₁Cr/TiO₂光催化剂的可见光催化活性,讨论了光催化反应机理,并与TiO₂的光催化反应机理进行了比较;考察了焙烧温度、PW₁₁Cr剂量和溶液pH值对光催化活性的影响;最后用RhB的循环降解实验评估了催化剂的光催化稳定性。 实验结果表明,PW₁₁Cr/TiO₂光催化剂对可见光有明显吸收,较低焙烧温度(100 ℃)下得到的膜为无定形结构,而较高焙烧温度(500 ℃)为纳晶结构;前者的光催化活性较高,在200 W金卤灯照射下降解10 μmol/L RhB,120 min的降解率为95%,4 h的COD去除率为72%;羟基自由基是导致RhB降解的主要氧活性物质;低的膜处理温度,高的PW₁₁Cr负载量和溶液酸性有利于提高PW₁₁Cr/TiO₂膜的光催化活性;经循环重复使用10次,PW₁₁Cr/TiO₂膜的光催化活性仅有较少损失。     

Photocatalytic degradation of toluene in the gas phase: comparative study of some TiO2 supports

The Langmuir–Hinshelwood (L–H) kinetic model has been used to describe the degradation of the toluene on three TiO₂-based photocatalysts supports. The determination of the L–H rate constant (k) showed that the UV illumination parameter seems to be more important than the quantity of TiO₂ per unit area. The constant k is the greatest for the less density TiO₂ photocatalyst. The comparison between the Langmuir adsorption constant (K) in the dark and under UV irradiation shows that the adsorption constant for the high kinetic catalyst increases while it decreases for the other two.     

Photocatalytic degradation and kinetics of Orange G using nano-sized Sn(IV)/TiO2/AC photocatalyst

Sn(IV) doped and nano-sized TiO₂ immobilized on active carbon (AC) (Sn(IV)/TiO₂/AC) were prepared by the sol–gel and dip-calcination method. An azo dye, Orange G (OG), was used as a model compound to study its photocatalytic activity in a fluidized bed photoreactor. The addition of Sn(IV) on TiO₂ could greatly improve the activity of TiO₂, and the optimal amount of tin was 2.5 at.%. The effects of calcination temperature, pH value, the initial hydrogen peroxide concentration ([H₂O₂]₀), the catalyst amount ([TiO₂]), the initial OG concentration ([dye]₀) and co-existing negative ions on the photocatalytic activity of Sn(IV)/TiO₂/AC were studied. The optimal conditions were as follows: pH 2.00, [H₂O₂]₀ = 1.5mL/L, [dye]₀ = 50 mg/L, [TiO₂] = 12.5 g/L, when the 300 W high pressure mercury light was used as the light source. Under these conditions, the degradation efficiency of OG reached 99.1% after 60 min reaction. The kinetics of the OG degradation was also analyzed. The results showed that the kinetics of this reaction fit the Langmiur–Hinshelwood kinetics model well and the absorption of OG on the Sn(IV)/TiO₂/AC surface was the controlling step in the whole degradation process. In addition, the catalyst, liquid and gas were separated effectively, and the integrative process of reaction and separation was achieved during the experiment.     

Thermal behavior of nitrided TiO2/In2O3 by TG–DSC–MS combined with PulseTA

TiO₂/InN (In/(Ti + In) = 6.5:100 mol) was prepared by nitridation of TiO₂/In₂O₃ by NH₃ at 580 °C for 8 h. Only the anatase TiO₂ phase was detected in the XRD measurements. The highly dispersed InN clusters on the surface of anatase TiO₂ nanocrystals were beyond the detection limit of XRD. In order to confirm the existence of InN in the products of nitridation, thermogravimetry–differential scanning calorimetry–mass spectrometry (TG–DSC–MS) coupling techniques were used for a simultaneous characterizing study of the changes of mass, enthalpy and determination of the evolved gases during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃ samples. Moreover, pulse thermal analysis (PulseTA) was combined with TG–DSC–MS for the quantitative calibration of the evolved nitrogen formed during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃. The applied technique enabled identification and quantification of the InN in the products of the nitridation of TiO₂/In₂O_3.     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.