硬弹性聚丙烯的表观密度特征

研究了硬弹性聚丙烯形成过程中表观密度的变化特征。结果表明,熔体温度下降、所受拉伸比增加或冷却风速度升高均可使表观密度增加。硬弹性聚丙烯经热处理后,表观密度有所增加。硬弹性聚丙烯在拉伸过程中,表观密度先下降而后增加,呈现出最低值,这一变化规律与硬弹性聚丙烯中片晶分离形成微孔的特性有关。     

原位小角X射线散射研究热拉工艺对熔融拉伸法制备的聚丙烯微孔膜结构的影响

采用原位小角X射线散射和扫描电子显微镜研究了热拉过程中,拉伸比和拉伸温度对熔融拉伸法制备的聚丙烯微孔膜晶体和孔洞结构的影响.研究结果表明,冷拉、热定型过程中片晶簇被分离开,其内部结构在热拉过程中不发生分离等变形;随着热拉拉伸比的增加,片晶簇间架桥长度不断增大;与冷拉、热定型样品相比,热拉后的微孔膜架桥沿垂直于拉伸方向具有较好的周期性.不同的拉伸温度结果表明,架桥长度随拉伸温度升高而增加;温度过高时架桥会发生熔融.     

原位X射线研究拉伸过程中间规聚丙烯晶体熔融与晶体取向关系

间规聚丙烯熔体(sPP)淬冷至液氮温度并保持5 min, 于20, 40, 80, 120 ℃下等温退火10 h, 制备出具有不同片晶厚度的样品. 在室温条件下, 利用原位X射线在线研究sPP样品拉伸过程中应力诱导的晶体熔融和晶体取向关系. 结果表明, 在单轴拉伸过程中, 应力导致的晶体熔融和晶体取向同时发生, 即两者在同一应变、 同一应力下同时发生, 这一特性不受片晶厚度的影响. 随着片晶厚度的增加, 晶体熔融和取向需要的临界应力不断增大, 在所研究范围内, 该临界应力的增加和片晶厚度基本呈线性关系. 另外, 随着片晶厚度增大, 样品的弹性模量、 屈服强度和应变硬化模量均有一定程度的增大.     

硬弹性聚丙烯纤维分子链的取向特征

硬弹性聚丙烯是在应变结晶和热结晶两个复合过程中形成的。利用双折射并结合广角X射线衍射（WAXD）等方法，研究了硬弹性聚丙烯在制备过程中晶相及非晶相分子链取向的变化，讨论了分了链的取向与硬弹性的关系。结果发现：降低熔体温度或提高熔体拉伸比可以提高晶相及非晶相分子链的取向，热处理时，晶相分子链的取向程度有所提高，而非晶相分子链的取向程度有所下降。在所研究的热处理温度的范围内，硬弹性聚丙烯的弹性回复率越高，晶相分子链的取向程度越高。     

熔融拉伸法制备聚丙烯微孔膜成孔机理的原位小角X射线散射研究

采用熔融拉伸法制备聚丙烯微孔膜,在避免冷拉会自然回缩和热处理后样品需降温检测等因素对冷拉伸样品影响的情况下,在线研究了冷拉、热定型、热拉过程中样品结构变化.原位小角X射线散射检测与扫描电子显微镜、示差扫描量热仪结合深入研究了不同的冷拉拉伸比对微孔膜片晶和孔洞结构的影响.结果表明不同的冷拉伸比其成孔机理不同,冷拉15%,仅拉伸方向长周期发生微弱的变化,其成孔机理是冷拉产生缺陷,热拉成孔;冷拉30%拉伸主要是将薄弱片晶拉伸转变为不稳定的架桥,热定型阶段部分架桥断裂,竖直方向上产生明显的Streak信号;冷拉40%拉伸方向信号显示实际片晶长周期的增长率小于宏观应变,部分骨架片晶在冷拉阶段已被拉伸破坏成孔.随着冷拉拉伸比增大架桥长度变短,孔径减小,30%是制备微孔膜较合适的冷拉拉伸比.     

聚丙烯中空纤维膜的微孔结构的控制

通过熔纺／冷拉伸法制备了微孔聚丙烯中空纤维膜。研究了工艺条件对微孔聚丙烯中空纤维膜的微孔结构与性能的影响。结果表明：随着纺丝温度的下降或熔体拉伸比的提高，最大可几孔径及孔隙率增大；熔纺中冷却风速提高，最大可几孔径及孔隙率较大；温度低于110℃时，热处理对最大可几孔径及孔隙率的影响较小，在120－130℃时，随着热处理温度的增加，最大孔径及孔隙率有明显增加的趋势；随着初纺中空纤维拉伸倍数的增加，孔隙率先增加而后下降。     

高分子量级分含量对熔体挤出拉伸法制备聚丙烯微孔膜的影响

通过熔体挤出拉伸法以两种聚丙烯为原料制备微孔膜.通过考察原料分子量数据发现高分子量聚丙烯(PPH)在高分子量级分(重均分子量>106)含量上大于低分子量聚丙烯(F401).PPH的弛豫时间在相同条件下也远大于F401.红外二向光法结果表明,PPH在相同熔体牵伸比下片晶取向度较F401高.相同加工条件下PPH微孔膜片较F401成孔分布更均匀,孔径尺寸也更均匀.2种微孔膜孔隙率都随熔体牵伸比的增加而提高,微孔分布随着熔体牵伸比的提高和片晶取向度的增加而趋于均匀,孔尺寸也随之区域均匀.研究表明,聚合物树脂中高分子量级分含量是影响预制膜中片晶取向度、冷热拉伸成孔分布和尺寸均匀度的重要影响因素.     

应力场下固—液相分离制备微孔聚丙烯中空纤维膜

将聚丙烯和石蜡油的混合物熔融挤出,使之在较高的应力场下冷却和相分离,得到了弹性聚丙烯中空纤维。这种部分结晶的弹性纤维可能具有平行排列的片晶结构,石蜡油存在于片晶之间。将石蜡油提取掉后稍加拉伸即可得到透气性很好的微孔中空纤维渗透膜。     

在高压CO_2中聚乙二醇-聚己内酯嵌段共聚物的结晶行为

通过广角X射线衍射(WAXD)和小角X射线散射(SAXS)方法研究了PEO-b-PCL在CO2中的结晶形貌和片晶厚度的变化,利用高压示差扫描量热仪(HP DSC)考察了压力对熔融和等温结晶过程的影响.结果表明,PEO-b-PCL的结晶度、片晶厚度、熔融温度均随压力的升高而减小,结晶结构变得不完善.在等温结晶过程中,结晶速率随压力的升高而下降,结晶过程处于成核控制区,Avrami指数n在3.7~4.7,表明晶体的生长方式为三维生长.     

水热处理对聚酰胺6纤维结构和性能的影响

在150℃下对聚酰胺6(PA6)纤维进行了水热处理,通过二维广角X射线衍射(2D-WAXD)、二维小角X射线散射(2D-SAXS)、示差扫描量热法(DSC)、场发射扫描电子显微镜(FE-SEM)和单丝强力测试等表征方法,研究了水热处理对纤维结构、热学和力学性能的影响.水热条件下,随温度的增加,水分子渗透作用增强,分子链的运动加剧,纤维的内部结构发生变化.纤维晶区结构由原来的γ晶型转变成为α晶型,结晶度和晶区完善程度提高,微晶尺寸增加,从而使纤维的热稳定性提高,熔融温度和熔融焓增加.水热处理使得纤维形成了折叠链片晶结构.在拉伸过程中,纤维的长周期不断增加,片晶有序性排列程度提高.水热处理后PA6纤维非晶区体积分数降低,并伴随有微孔和大的孔洞的形成,纤维的断裂强度和断裂伸长率都有所降低.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.