Syntheses and degradations of fluorinated heterocyclics. IV. Imidoylamidoximes, 1,2,4-oxadiazole precursors

Perfluoroalkylether amidoximes free from amide-contamination were prepared from imidate esters. The amidoximes were stable at 110°C; at ～170°C partial decomposition to 1,2,4-oxadiazoles, admixed with other compounds, took place. Interactions between nitriles and amidoximes at 50°C resulted in the formation of imidoylamidoximes; these dissociated readily into their constituents when subjected to higher temperatures. At 70°C and above, in the presence of excess nitrile or other ammonia acceptors, the imidoylamidoximes afforded high yields of the corresponding 1,2,4- oxadiazoles.     

Oligomeric polyaromatic ether-ketone-sulfones with acetylenic end groups. IX.

Two oligomeric polyaryl ether-ketone-sulfones with acetylenic end groups have been prepared. These materials which are low melting and readily soluble in organic solvents on heating undergo reactions which are presumably trimerizations of the terminal acetylenic groups to give cured polymers which do not soften until about 200°C and which are stable in circulating air at 300°C with less than 10% weight loss in 10 days.     

High Acceleration and Improved Diastereoselectivity of Intramolecular Ene-Type Reactions by Diethylaluminum Chloride. Preliminary Communication

The pyrrolidines 2 and 10 were obtained by thermal ene-reactions at +70° and +180° from the (Z)-4-aza-1, 6-diene 1 and from the (E)-4-aza-1, 6-diene 9 in the ratios of 75:25 and 50:50, respectively. On the other hand, these cyclizations proceeded readily in the presence of diethylaluminum chloride at ? 78° and ? 35° giving in high yield the trans-pyrrolidine 2 from 1 with 100% and from 9 with 89% diastereoselectivity.     

Polymerization of propiolaldehyde. IV. Synthesis of a functional polymer having an ethynyl group

The cationic homopolymerization and copolymerization of propiolaldehyde were carried out with use of boron trifluoride etherate as an initiator at the temperatures of 0 to ?78°C. Poly(ethynyl)oxymethylene was prepared by the homopolymerization at ?78°C, but it was readily depolymerized to the monomer. The cationic copolymerization with styrene at ?78°C proceeded almost exclusively through the aldehyde addition and a new functional copolymer was obtained. With a rise in polymerization temperature, the ethynyl addition was mixed slightly.     

Lithiation of 1-benzenesulfonylimidazole. Characterization of authentic 2-lodoimidazole

Lilhiulion of 1-betizenesulfonylimidazole takes place readily at ?20° or 0° in THE. The lithium reagent gives products of addition to typical carhonyl compounds but only in low yield, lodination occurs at the 2-position, in low yield, and authentic 2-iodoimidazole is obtained by cleavage ol the henzenesulfonyl group.     

Polyimidines,a new class of polymers. II. Polyhexamethylenetetraphenyldithiopyromellitimidine

Polyimidines have been shown to be soluble, thermally stable polymers. In searching for an alternate synthetic method the thio analog of this system has been discovered. The brightly colored (red-orange) perthio derivatives of 3,3-diphenylphthalide and 3,3,5,5-tetraphenyipyromellitide were synthesized from their oxo analogs with P₂S₅. The model compound thioimidines were synthesized by reacting 3,3-diphenyldithiophthalide with aniline and with 1,6-hexane diamine and by reacting 3,3,5,5-tetraphenyltetrathiopyromellitide with aniline and n-hexylamine. The polymerization of tetraphenyltetrathiopyromellitide occurred readily with 1,6-hexanediamine in boiling carbon tetrachloride with complete cyclization. This reaction gave an 80% yield with inherent viscosities up to 0.89 and molecular weights up to approximately 11,000. Thermogravimetric analysis showed a 2% weight loss at 200°C and 10% weight loss at 300°C with rapid decomposition above 300°C. Although the polythioimidine was less thermally stable than its oxo analog, it was much more soluble in common solvents (aromatic and chlorinated aliphatic hydrocarbons) and more readily synthesized in higher yield.     

Regular copolyamides. II. Preparation and characterization of regular aliphatic copolyoxamides

Regular copolyoxamides were prepared from diamine-oxamides and aliphatic diacid chlorides by interfacial and solution polymerization. Interfacial polymerization is preferred with diamineoxamides where the diamine portion has two to six methylene groups and the diamine-oxamides are readily soluble in water. Regular aliphatic polyoxamides from diamine-oxamides are readily soluble in water. Regular aliphatic polyoxamides from diamine-oxamides with more than six methylene groups in the diamine portion of the molecule are better prepared by solution polymerization in dimethyl acetamide. Regular aliphatic oxamides are soluble in trifluoroacetic acid and hexafluoroisopropanol and show a considerable alternation of the melting point behavior in the diamine portion of the polyamides with up to five methylene groups. Copolyoxamides with two and four methylene groups melt higher than the copolyoxamides with three and five methylene groups. Aliphatic copolyoxamides/adipamides melt at approximately 260°C and show a steady decrease in melting points to about 220°C for polyoxamides with twelve methylene groups.     

Synthesis and characterization of aromatic polymers containing pendant silyl groups. I. Polyarylates

Polyarylates containing pendant silyl group were prepared by the phase-transfer catalyzed, two-phase polycondensations of 2,2-bis (4-hydroxyphenyl) propane with corresponding dicarbonyl chlorides such as 2-trimethylsilylterephthaloyl chloride, 5-trimethylsilylisophthaloyl chloride, 5-dimethylphenylsilylisophthaloyl chloride, and 5-triphenylsilylisophthaloyl chloride. The resulting amorphous polyarylates with glass transition temperatures of 163–214°C had inherent viscosities in the range of 0.41–0.95 dL/g. These polyarylates were readily soluble in common chlorinated hydrocarbons and it was possible to obtain transparent, flexible, and tough films from the polymer solutions. The prepared polyarylates showed fairly good thermal stabilities as well as tensile strengths, i.e., the tensile strengths of the cast films from chloroform solution were 6.0–6.7 kg/mm². And TGA data revealed 10% weight losses and residual weights at 800°C were 437–495°C and 27–40% under nitrogen atmosphere, respectively. © 1992 John Wiley & Sons, Inc.     

Aromatic polyethers,polysulfones, and polyketones as laminating resins. VI. Polymers from 2,5-dicyanoterephthalic acid

Aromatic poly(keto ether sulfones) containing various amounts of pendant cyano groups were synthesized from 1,4-bis(p-phenoxybenzoyl)-2,5-dicyanobenzene, 1,3-bis(p-phenoxybenzenesulfonyl)benzene, and isophthaloyl chloride by a Friedel-Crafts type polymerization. These polymers softened at 160–190°C and had inherent viscosities of 0.44–0.61 in hexamethylphosphoric triamide. Crosslinkings were made by heating the polymers alone or in the presence of zinc chloride at 360–370°C to give black resinous materials that were insoluble in hexamethylphosphoric triamide in which the original polymers dissolved quite readily.     

New poly(amide-imide)s syntheses. VIII. Preparation and properties of poly (amide-imide)s derived from 2,3-bis(4-aminophenoxy)naphthalene,trimellitic anhydride,and various aromatic diamines

The new polymer-forming diimide-diacid, 2,3-bis(4-trimellitimidophenoxy) naphthalene (I), was readily obtained by the condensation reaction of 2,3-bis (4-aminophenoxy) naphthalene with trimellitic anhydride. A series of novel aromatic poly (amide-imide)s were prepared by the direct polycondensation of diimide-diacid I with various aromatic diamines using triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. The resultant polymers have inherent viscosities in the range of 0.65–1.02 dL/g at 30°C in N, N-dimethylacetamide. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed tensile strength at break up to 86 MPa, elongation to break of 5–9%, and initial moduli up to 2.35 GPa. The wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or p-oxyphenylene group are partially crystalline, and the other polymers are evidenced as amorphous patterns. These polymers show a glass transition in the range of 213–290°C in their differential scanning calorimetry (DSC) traces. The thermal stability of the polymers was evaluated by thermogravimetry analysis, which showed the 10% weight-loss temperatures in the range of 508–565°C in nitrogen and 480–529°C in air atmosphere. © 1994 John Wiley & Sons, Inc.     

Radiation-induced solid-state polymerization of derivatives of methacrylic acid. II. Postirradiation polymerization of octadecyl methacrylate

Octadecyl methacrylate (mpc ≈ 12°C.) polymerized readily in the solid state in the temperature range ?30 to +12°C. after gamma irradiation at ?196°C. The initial rate of polymerization and the “limiting” conversion increased with radiation dose and temperature. The temperature dependence of the rate corresponded to an “apparent” activation energy of 20 kcal./mole. Difficulties were experienced with polymerization during separation of the polymer from residual monomer, but these were minimized by using low radiation doses and a hot, selective solvent. The maximum conversion achieved was 70%. The polymer was crosslinked, even at low conversions.     

Boron–nitrogen polymers. I. Mechanistic studies of borazine pyrolyses

Pyrolyses of B-triamino-N-triphenyl-, B-triamino-N-trimethyl-, and B-trianilino-borazines were performed between 150 and 300°C. Initial stages of degradation were accompanied by liberation of ammonia in addition to the expected aniline or methylamine; this was most pronounced for the methyl borazine. Aniline elimination proceeded more readily with the B-anilino than the B-amino isomer. Data obtained support a ring opening mechanism resulting in telomerizaton accompanied by aniline liberation and formation first of singly then doubly bridged dimers and finally doubly bridged tetramers. Thermal exposure up to 1000°C failed to give pure boron nitride; carbon was invariably retained.     

Haloaldehyde polymers. IX. Polybromodichloroacetaldehyde

Bromodichloroacetaldehyde was synthesized by two methods. The first synthesis started from chloral, which was allowed to react with Ph₃P and the resultant compound brominated and hydrolyzed to give bromodichloroacetaldehyde in an overall yield of 60%. Purification by repeated distillation from P₂O₅ gave polymerization grade bromodichloroacetabldehyde. Bromodichloroacetaldehyde could also be synthesized by bromination of dichloroacetaldehyde diethyl acetal. The yields of this synthesis were only 20–30%, and the aldehyde could not be purified readily to give polymerization grade monomer. Bromodichloroacetaldehyde could be homopolymerized at ?30°C with anionic and also some cationic initiators to a polymer which was insoluble and did not melt but degraded to monomer above 200°C. The ceiling temperature of the polymerization was ?15°C in 1M solution. Bromodichloroacetaldehyde could also be copolymerized with isocyanates, primarily aryl isocyanates, and also with chloral.     

Aminopyridine-containing supramolecular polydiacetylene: film formation,thermochromism and micropatterning

Polydiacetylenes (PDAs) are intrinsically supramolecular conjugated polymers that are prepared by polymerisation of self-assembled diacetylene (DA) supramolecules. Owing to their highly aggregating nature and insolubility, fabrication of transparent and homogeneous films has been challenging. By taking advantage of multiple hydrogen bonding, a transparent and thin PDA film was readily prepared with an aminopyridine-containing DA monomer. The PDA film displayed an irreversible blue-to-red colour change between 30 and 90 °C and a reversible red-to-yellow thermochromism between 30 and 190 °C. Micropatterned colour and fluorescence PDA images were readily fabricated by employing a simple photolithographic approach.     

Radiation-induced,solid-state polymerization of derivatives of methacrylic acid. I. Postirradiation polymerization of zinc methacrylate

The postirradiation polymerization of the crystalline, anhydrous, monohydrate, and dihydrate forms of zinc methacrylate was studied. The anhydrous salt polymerized readily in the temperature range 50–150°C., the monohydrate did not polymerize at all, and the dihydrate polymerized at about 100°C. Aging of the anhydrous salts greatly affected the rate of polymerization; this was shown to be due mainly to the formation of peroxides by reaction with air. Polymerization could be initiated thermally, without irradiation, in monomer which had been aged in contact with air, apparently by decomposition of the peroxides. The rate of the postirradiation polymerization was increased when air was present during irradiation and decreased when air was present during polymerization. The rate of polymerization increased with temperature, corresponding to an apparent activation energy of 10 kcal./mole. The dihydrate lost one molecule of water rapidly under vacuum at 20°C. and slowly on heating at 50°C. in a sealed vessel, forming a crystalline monohydrate. Slow thermal polymerization and rapid postirradiation polymerization occurred at 100°C. without the formation of any monohydrate, indicating that the polymerization was concurrent with the phase change.     

An Efficient Method for Production and Storage of Unstable S-Nitrosothiols Under Mild and Heterogeneous Condition with Sodium Nitrite and Oxalic Acid Dihydrate

Thiols can be readily converted to their corresponding nitrosothiols with a combination of oxalic acid and sodium nitrite in t-butanol at room temperature (26-30°C). The reaction mixture could be solidified with decreasing its temperature to, 15°C and was stored for several days without any destruction of the nitrosothiols.     

New poly(amide-imide)s syntheses. II. Soluble poly(amide-imide)s derived from 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene and various N-(ω-carboxyalkyl)-trimellitimides,N-(carboxyphenyl)trimellitimides,or N,N″-bis(ω-carboxyalkyl)pyromellitimides

Various dicarboxylic acids with preformed imide rings were readily obtained by the condensation of ω-amino acids and aminobenzoic acids with trimellitic anhydride, and omega;-amino acids with pyromellitic dianhydride. New tetraphenylthiophene-containing poly(amide-imide)s having inherent viscosities of 0.58-1.54 dL/g were prepared by the direct polycondensation reaction of 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene with the imide-containing dicarboxylic acids using triphenyl phosphite and pyridine as condensing agents. These polymers were amorphous and readily soluble in a variety of solvents such as dimethylacetamide (DMAc), dimethylformamide (DMF), and N-methyl–2-pyrrolidone (NMP), and could be easily solution cast into transparent, flexible, and tough films. Most of the poly(amide-imide)s showed clear glass transition on the heating traces of differential scanning calorimetry (DSC) in the range of 146–244°C. Almost all the poly(amide-imide)s exhibited no appreciable decomposition below 400°C, with 10% weight loss being recorded above 420°C in nitrogen. © 1992 John Wiley & Sons, Inc.     

Transmetallation of n-(trialkylstannyl)methylimines. A new method for the generation and cycloaddition of 2-azaallyl anions.

Transmetallation of imines 1 at −78° with RLi provided 2-azaallyl anions 2, which readily undergo cycloaddition with olefinic anionophiles, providing pyrrolidines. Of particular note is the generation of unstabilized 2-azaallyl anions for the first time (Table 1, entries 1–3).     

Preparation and properties of aromatic polypyrazoles from branched bis-β-diketones and aromatic dihydrazines

Aromatic polypyrazoles were prepared by the cyclopolycondensation of branched bis-β-diketones with aromatic dihydrazines. The polymerizations were carried out at 100–150°C in m-cresol or a polar aprotic solvent like dimethyl sulfoxide to produce polymers with inherent viscosities up to 0.98 dl/g. These polypyrazoles were readily soluble in a wide range of solvents that included chloroform and exhibited 10% weight losses between 380 and 425°C in air and 370 and 500°C in nitrogen.     

New poly(amide-imide)s syntheses. I. Soluble high-temperature poly(amide-imide)s derived from 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene and various aromatic diamines

Novel aromatic poly(amide-imide)s with high inherent viscosities were prepared by direct polycondensation reaction of 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene ( IV ) and aromatic diamines using triphenyl phosphite in the N-methyl–2-pyrrolidone (NMP)/pyridine solution containing dissolved CaCl₂. The diimide-diacid IV was readily obtained by the condensation reaction of 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene ( III ₁) with trimellitic anhydride. The obtained poly(amide-imide)s showed high thermostability. Their decomposition temperatures at 10% weight loss in nitrogen atmospheres were above 550°C and the anaerobic char yield at 800°C ranged from 48 to 68%. Almost all the poly(amide-imide)s showed high glass transition temperatures above 300°C by differential scanning calorimetry (DSC) measurements. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed obvious yield points in the stress-strain curves and had strength at break up to 74.2 MPa, elongation to break up to 70.1%, and initial modulus up to 4.56 GPa. The factors affecting the reaction of diimide-diacid IV and 4,4′-oxydianiline in view of monomer concentration, reaction temperature, and amount of CaCl₂ were also investigated. © 1992 John Wiley & Sons, Inc.