The evolution of morphology of ordered porous TiO2 films fabricated from sol-gel method assisted ZnO nanorod template

Ordered porous TiO₂ films, including TiO₂ nanotube arrays, are fabricated by a sol-gel dip-coating approach via ZnO nanorod templates obtained from aqueous solution approach. The results indicate that the morphologies of ordered porous TiO₂ films have been great affected by the sol-gel dip-coating cycle number. Open-ended TiO₂ nanotube arrays can be obtained in optimum dip-coating cycle numbers. The TiO₂ nanotubes with the inner diameter matching well with the diameters of ZnO nanorods, are well assembled and separate each other. When the cycle number is less than this optimum value, no intact porous TiO₂ film can be obtained. As the cycle number is larger than this optimum value, an ordered porous TiO₂ film with many throughout holes is formed. The evolutive mechanism of ordered porous TiO₂ films is proposed.     

Analysis of electro-optical and dielectric parameters of TiO2 nanoparticles dispersed nematic liquid crystal

The present investigation is focused on to find out the role of TiO₂ nanoparticles (NPs) on altering the dielectric and electro-optical parameters of nematic liquid crystal (NLC). In addition to this, we also optimized the concentration of dopant (0.25 wt%) for a saturation value of permittivity and dielectric anisotropy in the doped system. Dielectric spectroscopy has been performed with the variation of frequency and temperature to investigate the various dielectric parameters, which demonstrate that the investigated NLC is of positive dielectric anisotropy; the observed result shows a decrement in the value of relative permittivity and dielectric anisotropy; however, the permittivity value increases for higher concentration of dopant but remains less than that of pure NLC. Electro-optical measurements have also been performed to compute the optical response of pure and dispersed NLC. It is found that optical response decreases for the NP-doped systems. This optimized concentration of NPs in NLC matrix can have various credential applications in the field of active matrix display and holography.     

Structure of TiO2 in TiO2-SiO2 prepared by a complexing agent-assisted sol-gel procedure

Many types of TiO₂-SiO₂ (Ti:Si=50:50 mol%) were prepared by the sol-gel procedure with and without 2-methyl-2, 4-pentanediol (MPD) as an organic ligand. The effect of MPD on the gel structure and the properties of the TiO₂ crystals were studied by XRD and raman spectroscopy, and the effect of the sol standing time on the properties of the TiO₂ crystals were also studied by XRD spectroscopy. In the gels with MPD, anatase of TiO₂ appeared at approximately 580°C, and the crystal structures were similar despite the difference in the gel preparation procedure. The titania gels with MPD were presumed to be dispersed in the silica gel matrix without any Ti-O-Si bond. In the presence of MPD, the formation of titania gels is controlled and the specified TiO₂ crystal is produced.     

3D nanomaterial silica aerogel via diffusion of chiral compound driven broadband reflection in chiral nematic liquid crystals

In the study, a novel method of broadening the bandwidth by fabricating the silica aerogel film composited with the chiral nematic liquid crystal (N*-LC) is proposed. Diffusion of chiral compound filled in the silica aerogel resulted in the non-uniform pitch distribution, which can be anchored by UV-radical polymerisation. The results strongly suggested that the reflection bandwidth could be broadened preferably by adjusting the silica aerogel condensation time, the content of UV polymerisable free radical monomer and the polymerisation temperature. The reflection bandwidth was broadened from 270 nm to 878 nm, and the centre wavelength was blue-shifted by 642 nm. A general correlation among the silica aerogel condensation time, the polymerisation condition, and the reflective region will be outlined.     

Effects of polymer network on electrically induced reflection band broadening of cholesteric liquid crystals

The reflection band of polymer stabilized cholesteric liquid crystals with negative dielectric anisotropy can be broadened by DC electric fields, which was ascribed to the pitch gradient caused by the motion of the structural chirality, that is, the polymer network. They systematically varied the mixture components, such as the photo‐initiator concentration, the monomer functionality, and the chiral dopant, to explore their influences on the reflection band broadening behavior. They learned how to control the polymer network morphology and ion density, which in turn determined the reflection bandwidth. By optimizing the mixture, they have greatly enhanced the broadening effect and achieved large bandwidth at low voltages. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 835–846     

NMR spectra of chiral smectic liquid crystals differing in helical parameters

Chiral liquid crystals with three-ring rigid core were examined. The method based on the selectively reflected light was used to determine the helical pitch. The helical twist sense was worked out using the polarimetry method. ¹H and ¹³C NMR measurements were performed. The influence of three molecular structure parameters: the type of chiral centre, the length of non-chiral chain and substitution of benzene ring by fluorine atoms, on helical pitch, handedness of helical structure and values of chemical shift in proton and carbon spectra was determined. The change of the length of non-chiral terminal chain has the most significant influence on the temperature dependence of helical pitch. All tested parameters have the biggest influence on the values of chemical shift of atoms in the chiral centre.     

In situ fabrication of highly organised TiO2 nanoparticles with photo-catalytic activity in cholesterol-based organogel network

In this paper, we developed low molecular weight gel system based on cholesterol derivative containing pyridine unit attached through β-alanine linkage, which can act as efficient gelator to form novel gel systems in organic or organic–water solvents. Spherical nanoscale anatase–TiO₂ with porous structure was obtained through the in situ hydrolysis in the gel tissue upon the instant addition of water followed by calcination, which had photo catalytic activity toward naphthol blue black. To the best of our knowledge, this is the first example that cholesterol-based gel tissue was employed as the template to construct TiO₂ with photo-catalytic activity.     

Comparison of CO2 Reduction Performance with NH3 and H2O between Cu/TiO2 and Pd/TiO2

The aim of this study is to clarify the effect of doped metal type on CO₂ reduction characteristics of TiO₂ with NH₃ and H₂O. Cu and Pd have been selected as dopants for TiO₂. In addition, the impact of molar ratio of CO₂ to reductants NH₃ and H₂O has been investigated. A TiO₂ photocatalyst was prepared by a sol-gel and dip-coating process, and then doped with Cu or Pd fine particles by using the pulse arc plasma gun method. The prepared Cu/TiO₂ film and Pd/TiO₂ film were characterized by SEM, EPMA, TEM, STEM, EDX, EDS and EELS. This study also has investigated the performance of CO₂ reduction under the illumination condition of Xe lamp with or without ultraviolet (UV) light. As a result, it is revealed that the CO₂ reduction performance with Cu/TiO₂ under the illumination condition of Xe lamp with UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:1:1 while that without UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:0.5:0.5. It is revealed that the CO₂ reduction performance of Pd/TiO₂ is the highest for the molar ratio of CO₂/NH₃/H₂O = 1:1:1 no matter the used Xe lamp was with or without UV light. The molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp with UV light was 10.2 μmol/g, while that for Pd/TiO₂ was 5.5 μmol/g. Meanwhile, the molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp without UV light was 2.5 μmol/g, while that for Pd/TiO₂ was 3.5 μmol/g. This study has concluded that Cu/TiO₂ is superior to Pd/TiO₂ from the viewpoint of the molar quantity of CO per unit weight of photocatalyst as well as the quantum efficiency.     

Thermally effected structural and surface transformations of sulfated TiO2, ZrO2 and TiO2-ZrO2 catalysts

Preparations were characterized by specific surface area, thermogravimetry, and X-ray diffractometry. Thermal effects observed were (a) sulfur loss, (b) sintering, (c) crystallization and transformation of the crystalline phase(s). Thermoanalytical curves indicate that decomposition of the sulfate occurs in two distinct steps. Decrease of surface area due to (b) and (c) is concomitant to decomposition of sulfate. Sulfate was found to hinder sintering, crystallization and phase transformations of ZrO₂ and TiO₂. In low-titania and -zirconia sulfated TiO₂-ZrO₂ the minor component enhances the effect of sulfate. In equimolar TiO₂-ZrO₂ sulfate decomposition is accompanied by rapid formation of crystalline TiZrO₄.This work was supported by the MOL Rt., Hungary, which is gratefully acknowledged.     

Electrochemical sensor for acetaminophen based on an imprinted TiO2 thin film prepared by liquid phase deposition

An electrochemical sensor based on a molecularly imprinted TiO₂ thin film is proposed for the determination of acetaminophen. The imprinted TiO₂ films were obtained by liquid phase deposition (LPD) in the presence of acetaminophen, the functional monomer and the aqueous solution of (NH₄)₂TiF₆ and H₃BO₃. The results show that acetaminophen is embedded into the imprinted film in the presence of p-tert-butylcalix[6]arene as a functional monomer, and can be removed completely by washing with ethanol. The surface morphology, spectral properties and electrochemical characterizations of the imprinted sensor were investigated in detail. The combination of molecularly imprinted and LPD technique was shown to be a general strategy for constructing a molecular recognition system.     

CuO Catalysts Supported on Porous TiO2 Microspheres for Low-Temperature CO Oxidation

The porous TiO₂ microspheres were prepared by the reversed-phase suspension polymerization and sol-gel method using reversed-phase suspension droplets as the templates. The CO oxidation catalytic properties of the CuO/TiO₂ catalysts prepared by hydrothermal method and impregnation method were extensively investigated. The structure of CuO/TiO₂ catalysts was determined by TG-DTA, XRD, TEM, and XPS. The results indicated that the redox capacity of CuO/TiO₂ was greatly depended on the aqueous solution concentration of Cu(NO₃)₂ used in the preparation of CuO/TiO₂ and the calcination temperature of the CuO/TiO₂ catalysts.     

Sol-Gel Derived TiO2-SiO2 Fibres

TiO₂−SiO₂ fibres with 0, 5, 10 and 20 volume % SiO₂ have been prepared by drawing from a gel followed by sintering at different temperatures. Nearly one meter long fibres can be drawn easily in conditions of about 50% relative humidity. Addition of SiO₂ inhibits the crystallisation of TiO₂ and also the anatase → rutile transformation and improves the strength of the fibres. While the pure TiO₂ fibres are brittle, those with 5, 10 and 20 volume % SiO₂ are flexible and strong. Tensile strength values as high as 3 GPa have been achieved in the 10 volume % SiO₂−TiO₂ fibres. Fibres heated above 900°C are brittle. The shape of the cross section of the fibres is found to depend on their diameters.     

Fabrication of TiO2 Grating with Composites of Azobenzene Polymer and TiO2 Nanoparticles

We have used the formation of surface relief gratings (SRG) on azobenzene polymers to manipulate TiO₂ nanoparticles and to fabricate TiO₂ nanoparticle gratings. Suspensions of an azobenzene polymer (PDO3) and TiO₂ were used to spin coat thin films on glass slide substrates. By interfering coherent light from an Argon laser on the surface of the PDO3‐TiO₂ composite films, SRGs were fabricated. Atomic force microscopic images of the SRGs show TiO₂ nanoparticles dispersed throughout the sample, and in particular, at the peaks of the SRG after oxygen plasma treatment. The lateral forces acting on the azobenzene polymer during the SRG fabrication drag the TiO₂ nanoparticles. These results indicated that it is feasible to create TiO₂ nanoparticle gratings with the composites.     

Blue TiO2 nanotube arrays as semimetallic materials with enhanced photoelectrochemical activity towards water splitting

In the past years there has been a great interest in self-doped TiO₂ nanotubes (blue TiO₂ nanotubes) compared to undoped ones owing to their high carrier density and conductivity. In this study, blue TiO₂ nanotubes are investigated as photoanode materials for photoelectrochemical water splitting. Blue TiO₂ nanotubes were fabricated with enhanced photoresponse behavior through electrochemical cathodic polarization on undoped and annealed TiO₂ nanotubes. The annealing temperature of undoped TiO₂ nanotubes was tuned before cathodic polarization, revealing that annealing at 500 °C improved the photoresponse of the nanotubes significantly. Further optimization of the blue TiO₂ nanotubes was achieved by adjusting the cathodic polarization parameters. Blue TiO₂ nanotubes obtained at the potential of –1.4 V (vs. SCE) with a duration of 10 min exhibited twice more photocurrent response (0.39 mA cm^-2) compared to the undoped TiO₂ nanotube arrays (0.19 mA cm^-2). Oxygen vacancies formed through the cathodic polarization decreased charge recombination and enhanced charge transfer rate; therefore, a high photoelectrochemical activity under visible light irradiation could be achieved.     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

Memory effects in chiral nematic liquid crystals doped with functionalised single-walled carbon nanotubes

Octadecylamine-functionalised single-walled carbon nanotubes (SWCNTs) were dispersed into nematic liquid crystals (LCs) doped with chiral molecules. The collective orientation of nematic LC molecules in helical layers was manipulated by varying dopant concentration. Highly anisotropic nature of SWCNTs enhanced the anisotropy of the LC as confirmed by polarised fluorescence spectroscopy. The π–π interaction of SWCNTs present in the planar alignment layers and twisted nematic LC molecules affects the molecular relaxation process. An irreversible electro-optic memory in the material has been observed.     

纳米TiO2-ZnO复合材料的合成、结构与光催化性能

Using ZnSO₄ and TiCl₄ as raw materials， nanometric TiO₂-ZnO (ZnTiO₃) is prepared at 180℃，0.8MPa by hydrothermal method. The effects of the reaction temperature and time on the nanometric TiO₂-ZnO are also dis-cussed. XRD shows that the product is TiO₂-ZnO (ZnTiO₃) with noncrystal phase， and it changes to rhombic form above 870℃. TEM measurement indicates that the TiO₂-ZnO is spherical particles， and the average diameter of the particles is 20nm. The UV light absorption properties are detected by UV spectrophotometer. The results show that the nanometric TiO₂-ZnO has strong absorption at 200～370nm and at visible region. Photodegradation of dyes in an aqueous solution is investigated using nanometric TiO₂-ZnO as a photocatalyst. The results show that after 60min illumination， the decolorization rate of the acidic red B and acidic black 234 dye can be arrived at 100%.     

Enhancement of ethanol electrooxidation on plasmonic Au/TiO2 nanotube arrays

Novel electrocatalysts Au/TiO₂ nanotube arrays (Au/TiO₂NTs) were prepared by loading low-content(1.9 at.%) of Au nanoparticles (AuNPs) onto highly ordered TiO₂ nanotube arrays (TiO₂NTs). Ethanol electrooxidation indicates that visible-light (λ > 400 nm) irradiation can significantly enhance the activity as well as resistpoisoning of Au/TiO₂NTs electrocatalysts that are activated by plasmon resonance. Au/TiO₂NTs catalysts calcinated at 300 °C display the highest performance due to the strong synergistic interactions between TiO₂ and Au NPs. The combination of visible-light irradiation with a controllable potential offers a new strategyfor enhancing the performance of anodes in direct ethanol fuel cell (DEFC).     

水热处理锐钛矿TiO2纳米管阵列及其增强的光电催化活性

在含氟溶液中,通过电化学阳极氧化钛片成功制备了高度有序的TiO2纳米管阵列,先在450℃下煅烧使其晶化为锐钛矿相,再在不同温度下水热处理了这些锐钛矿阵列。用XRD、SEM和XPS表征了所制备的样品。通过在氙灯光照下光电催化降解对氯苯酚水溶液来检测样品的活性。以对苯二甲酸作为探测分子,用荧光光谱检测了在氙灯光光照下样品表面产生的羟基自由基(.OH)。通过线性伏安扫描的间隙光照实验,测定了样品的光电流响应。结果表明后水热处理对锐钛矿TiO2纳米管阵列的结晶度和形貌没有影响,但光电催化活性明显增强,而不同温度处理的样品的活性差别不大。水热处理后的TiO2纳米管阵列的光电催化活性增强的原因是,水热后TiO2纳米管阵列表面羟基含量明显增加,使得其在光电催化过程中生成的.OH增加。     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.