Development of a new analytical method for Pb preconcentration and its further determination in water and foodstuffs using relatively low-sensitivity flame atomic absorption spectrometry

The present study describes chelation of Pb(II) with ascorbic acid and formation of a charge-transfer sensitive ion-pair in the presence of Rhodamine 6G at pH 5.5, and then its extraction to the micellar phase of non-ionic surfactant, PONPE 7.5 by an ultrasound-assisted cloud point extraction method before analysis by FAAS. The various variables affecting ion-pair formation and extraction efficiency were studied and optimised. Under the optimised conditions, the good linear relationships in the ranges of 0.4–150 μg L^?1 and 0.8–120 μg L^?1 for solvent-based calibration and matrix-matched calibration curves, respectively, were achieved with a pre-concentration factor of 71.4 from pre-concentration of 50-mL sample. Moreover, the limits of detection with good sensitivity enhancements of 124 and 114.5 were 0.13 and 0.24 μg L^?1, respectively, while the intra-day and inter-day precision (as RSD%, for five replicate measurements of 5 and 100 μg L^?1 in the same day and three succeed days) were in range of 2.8–5.4% and 3.7–6.3%, respectively. The matrix effect on triplicate determination of 50 µg L^?1 Pb(II) was also investigated. The accuracy of the method was statistically verified by the analysis of two certified reference materials (CRMs) after digestion with acid mixtures (HNO₃-H₂O₂-HF and HNO₃-H₂O₂) and dilution at suitable ratios. It has been observed that there is statistically not a significant difference between the certified- and found-values. The accuracy was also controlled using the pre-treated sample solutions spiked at different concentration levels, and the good spiked recoveries were obtained in range of 90–102.8%. The method was successfully applied to the determination of trace amounts of lead in water and food matrices with satisfactory results.     

A rapid microwave-assisted acid extraction method based on the use of diluted HNO3-H2O2 followed by ICP-MS analysis for simultaneous determination of trace elements in coal samples

Before coal processing such as pyrolysis, liquefaction, gasification and combustion, it is very crucial to monitor the trace element concentration levels as that determines the coal quality. Therefore, the current study describes the development of microwave-assisted acid extraction (MW-AAE) method for extraction of 15 trace elements in coal samples prior to their determination using inductively coupled plasma-mass spectrometry. Diluted HNO₃-H₂O₂ was used in order to reduce reagents amount used, eliminate matrix interferences caused by concentrated acids and to decrease waste produced in analytical laboratories. The optimisation of the proposed extraction method was carried out by using a full factorial design (2⁴) involving four factors; that is, temperature, extraction time, HNO₃ and H₂O₂ concentrations. The optimum conditions for the MW-AAE procedure were found to be 200°C, 5 min, 5 mol L^?1 and 2 mol L^?1 for temperature, extraction time, HNO₃ and H₂O₂ concentrations, respectively. Under optimum conditions, the accuracy of the MW-AAE method was examined by analysing three coal certified reference materials (SARM 18, 19 and 20) and recoveries of 80–115% were achieved for V, Mn, Co, Ni, Cu, Zn, Ga, Ge, As, Sr, Zr, Cs, Ba, Pb and U, except for Ti (10–25%) and Hf (27–70%). In addition, the precision of the proposed method, expressed in terms of relative standard deviation (SD) (n = 15), was within the accepted range (≤3.5%). The method detection limits of 0.001–0.57 µg g^?1 for all trace elements under the investigation were similar to the literature reported work, except for Ti (4.00 µg g^?1).     

Synergetic effect of Prussian blue film with gold nanoparticle graphite–wax composite electrode for the enzyme-free ultrasensitive hydrogen peroxide sensor

Enzyme-free amperometric ultrasensitive determination of hydrogen peroxide (H₂O₂) was investigated using a Prussian blue (PB) film-modified gold nanoparticles (AuNPs) graphite–wax composite electrode. A stable PB film was obtained on graphite surface through 2-aminoethanethiol (AET)-capped AuNPs by a simple approach. Field emission scanning electron microscope studies results in formation of PB nanoparticle in the size range of 60–80 nm. Surface modification of PB film on AET–AuNPs–GW composite electrode was confirmed by Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy studies. Highly sensitive determination of H₂O₂ at a peak potential of ?0.10 V (vs. SCE) in 0.1 M KCl PBS, pH?=?7.0) at a scan rate of 20 mVs^?1 with a sensitivity of 23.58 μA/mM was observed with the modified electrode using cyclic voltammetry. The synergetic effect of PB film with AuNPs has resulted in a linear range of 0.05 to 7,800 μM with a detection limit of 0.015 μM for H₂O₂ detection with the present electrode. Chronoamperometric studies recorded for the successive additions of H₂O₂ with the modified electrode showed an excellent linearity (R ²?=?0.9932) in the range of 4.8?×?10^?8 to 7.4?×?10^?8 M with a limit of detection of 1.4?×?10^?8 M. Selective determination of H₂O₂ in presence of various interferents was successfully demonstrated. Human urine samples and stain remover solutions were also investigated for H₂O₂ content.     

Automated Determination of Hydrogen Peroxide at the Micro-Molar Level in Rainwater and Snow Using a Stopped-Flow Approach in a Hybrid Sequential Injection/Flow Injection Manifold

A new automated method is reported for the determination of H₂O₂ in real samples. The method is based on the quenching effect of the analyte on the reaction between tris(2-carboxyethyl)phosphine (TCEP) and Ellman's reagent (DTNB). All necessary steps were accomplished under flow conditions using a hybrid sequential injection (SI)/flow injection (FI) setup. The sensitivity was enhanced by applying a stopped-flow step (120 s) in order to promote the reaction between H₂O₂ and TCEP. The proposed analytical protocol was validated for linearity (10–75 µmol L^?1), limits of detection (c _L = 1.0 µmol L^?1), quantitation (c _Q = 3.3 µmol L^?1), precision (s _r = 1.3–1.7%), accuracy, and selectivity. It was then applied successfully to the analysis of H₂O₂ in spiked rainwater and snow samples.     

Optical molecular fluorescence determination of ultra-trace beryllium in occupational and environmental samples using highly alkaline conditions

Exposures to beryllium (Be), even at extremely low levels, can cause severe health effects in a percentage of those exposed; consequently, occupational exposure limits (OELs) promulgated for this element are the lowest established for any element. This work describes the advantages of using highly alkaline dye solutions for determination of Be in occupational hygiene and environmental samples by means of an optical molecular fluorescence technique after sample extraction in 1–3% (w?w^?1) aqueous ammonium bifluoride (NH₄HF₂). Improved attributes include the ability to further enhance the detection limits of Be in extraction solutions of high acidity with minimal dilution, which is particularly beneficial when NH₄HF₂ solutions of higher concentration are used for extraction of Be from soil samples. Significant improvements in Be method detection limits (MDLs) are obtained at levels manyfold below those reported previously for this methodology. Notably, MDLs for Be of <0.01 ng L^?1 /0.1 ng per sample have been attained, which are superior to MDLs routinely reported for this element by means of the most widely used ultra-trace elemental measurement technique, inductively coupled plasma mass spectrometry (ICP-MS). Very low MDLs for Be are essential in consideration of reductions in OELs for this element in workplace air by health organisations and regulatory agencies in the USA and internationally. Applications of enhanced Be measurements to air filter samples, surface wipe samples, soils and newly designed occupational air sampler inserts are illustrated.     

Detection of trace nitrite in waters using a QDs-based chemiluminescence analysis system

In the present work, a novel flow-injection chemiluminescence method based on CdTe quantum dots (QDs) was developed for the determination of nitrite. Weak chemiluminescence (CL) signals were observed from a CdTe QDs–H₂O₂ system under basic conditions. The addition of a trace amount of hemoglobin (Hb) caused the CL from the CdTe QDs–H₂O₂ system to increase substantially. In the presence of nitrite, the ferrous Hb reacted with the nitrate to form ferric Hb and NO. The NO then bound to ferrous Hb to generate iron nitrosyl Hb. As a result, the CL signal from the CdTe QDs–H₂O₂–Hb system was quenched. Thus, a flow-injection CL analytical system for the determination of trace nitrite was established. Under optimum conditions, there was a good linear relationship between CL intensity and the concentration of nitrite in the range 1.0?×?10^?9 to 8.0?×?10^?7 mol L^?1 (R ²?=?0.9957). The limit of detection for nitrite using this system was 3.0?×?10^?10 mol L^?1 (S/N?=?3). This method was successfully applied to detect nitrite in water samples.

Highly Sensitive Flow-Injection Chemiluminescence Detection of Carbonyl Compounds in Wine Samples

A modified Trautz–Schorigin reaction, by using tannic acid-H₂O₂ system for the oxidation and determination of two kinds of carbonyl compounds was developed in this paper. It was found that formaldehyde and acetaldehyde could effectively enhance the chemiluminescence signals of tannic acid–H₂O₂ system in alkaline medium. Under optimized conditions, the proposed method has a linear range of 7 × 10^?9–1 × 10^?4 mol L^?1 for formaldehyde and 1 × 10^?8–1 × 10^?4 mol L^?1 for acetaldehyde with detection limits of 9 × 10^?11 and 3 × 10^?10 mol L^?1, respectively. The relative standard deviations for 15 repeated measurements of 1 × 10^?6 mol L^?1 HCHO and CH₃CHO are 1.13% and 1.65%, respectively. Analysis time per sample is 35 seconds. A comparison of results found by the proposed method with those obtained by a standard reference method provided good agreement. The proposed method is simple, rapid, convenient, and sensitive.     

A Chemiluminescence Microarray Based on Catalysis by CeO2 Nanoparticles and Its Application to Determine the Rate of Removal of Hydrogen Peroxide by Human Erythrocytes

In this work, cerium oxide nanoparticles are capable of strongly enhancing the chemiluminescence (CL) of the luminol–hydrogen peroxide (H₂O₂) system. Based on this, a microarray CL method for the determination of the removal rate constant of H₂O₂ by human erythrocytes has been developed. It is providing direct evidence for a H₂O₂-removing enzyme in human erythrocytes that acts as the predominant catalyst. A reaction mechanism is discussed. The proposed microarray CL method is sensitive, selective, simple and time-saving, and has good reproducibility and high throughput. Relative CL intensity is linearly related to the concentration of H₂O₂ in the range from 0.01 to 50 μM. The limit of detection is as low as 6.5?×?10^?11 M (3σ), and the relative standard deviation is 2. 1 % at 1 μM levels of H₂O₂ (for n?=?11).     

Electrochemical and physical characterization of Pt–Ru alloy catalyst deposited onto microporous–mesoporous carbon support derived from Mo2C at 600 °C

The electrochemical reduction of oxygen on binary Pt–Ru alloy deposited onto microporous–mesoporous carbon support was studied in 0.5 M H₂SO₄ solution using cyclic voltammetry, rotating disk electrode (RDE), and impedance method. The microporous–mesoporous carbon support C(Mo₂C) with specific surface area of 1,990 m²?g^?1 was prepared from Mo₂C at 600 °C using the chlorination method. Analysis of X-ray diffraction, photoelectron spectroscopy, and high-resolution transmission electron microscopy data confirms that the Pt–Ru alloy has been formed and the atomic fraction of Ru in the alloy was ～0.5. High cathodic oxygen reduction current densities (?160 A?m^?2 at 3,000 rev?min^?1) have been measured by the RDE method. The O₂ diffusion constant (1.9?±?0.3?×?10^?5?cm²?s^?1) and the number of electrons transferred per electroreduction of one O₂ molecule (～4), calculated from the Levich and Koutecky–Levich plots, are in agreement with literature data. Similarly to the Ru/RuO₂ system in H₂SO₄ aqueous solution, nearly capacitive behavior was observed from impedance data at very low ac frequencies, explained by slow electrical double-layer formation limited by the adsorption of reaction intermediates and products into microporous–mesoporous Pt–Ru–C(Mo₂C) catalyst. All results obtained for C(Mo₂C) and Pt–Ru–C(Mo₂C) electrodes have been compared with corresponding data for commercial carbon VULCAN® XC72 (C(Vulcan)) and Pt–Ru–C(Vulcan) electrodes processed and measured in the same experimental conditions. Higher activity for C(Mo₂C) and Pt–Ru–C(Mo₂C) has been demonstrated.     

Determination of Veterinary Pharmaceuticals in Production Wastewater by HPTLC-Videodensitometry

An SPE-HPTLC method for simultaneous identification and quantification of seven pharmaceuticals in production wastewater was optimized and validated. The studied compounds were enrofloxacine, oxytetracycline, trimethoprim, sulfamethazine, sulfadiazine, sulfaguanidine and penicillin G/procaine. The method involves solid-phase extraction on hydrophilic-lipophilic balance cartridges with methanol and HPTLC analysis of extracts on CN modified chromatographic plates followed by videodensitometry at 254 and 366 nm. Optimization of chromatographic separation was performed by systematic variation of the mobile phase composition using genetic algorithm approach and the optimum mobile phase composition for TLC separation was 0.05 M H₂C₂O₄:methanol = 0.81:0.19 (v/v). Linearity of the method was demonstrated in the ranges from 1.5 to 15.0 μg L⁻¹ for enrofloxacine, 100–500 μg L⁻¹ for oxytetracycline, 150–600 μg L⁻¹ for trimethoprim, 300–1100 μg L⁻¹ for sulfaguanidine and 100–400 μg L⁻¹ for sulfamethazine, sulfadiazine and penicillin G/procaine with coefficients of determination higher than 0.991. Mean recoveries ranged from 74.6 to 117.1% and 55.1 to 108.0% for wellspring water and production wastewater, respectively. Only sulfaguanidine showed lower results. The described method has been applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Aqueous Reactive Oxygen Species Induced by He + O<Subscript>2</Subscript> Plasmas: Chemistry Pathways and Dosage Control Approaches

Plasma–liquid interaction has already been a hotspot in the research field of plasma medicine. Aqueous reactive oxygen species (ROS) generated in this process are widely accepted playing a crucial role in plasma biomedical effects. In this paper, chemistry pathways among various aqueous ROS induced by He + O₂ plasmas are investigated by a numerical model. Simulation results show that these aqueous ROS can be classified into two groups according to their production ways: the group of species including O, ¹O₂ and e directly produced in plasma, and the other group of species including O₂ ^?, H₂O₂, O₃, etc. produced by liquid reactions. A key reaction chain of e → O₂ ^? → HO₂(→ HO₂ ^?) → H₂O₂ is found to be important in the plasma-induced liquid chemistry. Furthermore, impacts of changes in plasma and solution conditions on aqueous ROS concentrations are studied as well. It is found that changes in plasma conditions (O₂ ratio in the discharge gas/power density) can globally influence the concentrations of almost every aqueous ROS, while conditions changes of the treated liquid (pH/dissolved oxygen) only partially influence the concentrations of some specific species including O₂ ^?/HO₂, O₃ ^?/HO₃ and H₂O₂. The revelations of the liquid chemistry pathways and the dependence of ROS dosage on the treatment conditions offer a better understanding on the plasma–liquid interactions, as well as provide optimized dosage control approaches for biomedical applications.     

Separation of hafnium from tungsten by extraction chromatography with TOA in HCl–H<Subscript>2</Subscript>O<Subscript>2</Subscript> mixture

In order to measure ¹⁸²Hf by accelerator mass spectrometry (AMS), a chemical procedure for separation of hafnium from tungsten has been developed by extraction chromatography. The extraction chromatographic behavior of hafnium and tungsten has been studied using tri-n-octylamine (TOA) as the stationary phase, HCl–H₂O₂ mixture and NH₃·H₂O as the mobile phase. The effects of H₂O₂ concentration, column loading and column dimensions are investigated. Hf and W with microgram amounts are successfully separated on a chromatographic column (Ø5 × 196 mm), on which Hf is hardly retained after completely eluted with 6 M HCl–1% H₂O₂ and W strongly adsorbed is then eluted with 3 M NH₃·H₂O. The decontamination factor for tungsten is 3.0 × 10⁵ and the recovery of hafnium is better than 99% using a single column separation.     

Direct Electrochemistry of Hemoglobin in Cerium Dioxide/Carbon Nanotubes/Chitosan for Amperometric Detection of Hydrogen Peroxide

Abstract

A novel hemoglobin (Hb) biosensor based on the remarkable synergistic effects of cerium dioxide (CeO₂) and multiwalled carbon nanotubes (MWNTs) for detection of hydrogen peroxide (H₂O₂) is presented. The Hb/CeO₂/MWNTs/CHIT nanocomposite was nanoengineered by selected matched material components and optimized composition ratio to produce a superior H₂O₂ sensor. The preparation method is quite simple and practical. This composite matrix combined the advantages of MWNTs, CeO₂ nanoparticles, and chitosan (CHIT), with good electron-transfer ability, attractive biocompatibility, and fine film-forming ability, which could increase Hb attachment quantity and H₂O₂ detection sensitivity. In the optimum pH 7.0 phosphate buffer, the electrocatalytic response exhibited a linear dependence on H₂O₂ concentration in a wide range from 5.0 × 10^?6 to 4.6 × 10^?4 mol L^?1 with a detection limit of 6.5 × 10^?7 mol/L (3σ).     

Steam pre-reforming of natural gas over nanostructured Ni/12CaO–7Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst for hydrogen production: effect of support preparation method

Calcium aluminate (12CaO–7Al₂O₃) powder was synthesized using three methods, viz. Pechini, coprecipitation, and a new novel facile decomposition route starting from activated alumina and calcium nitrate precursors, then used as a support to prepare a series of 31 wt%Ni/12CaO–7Al₂O₃ catalysts by deposition–precipitation method. The resultant catalysts were tested in steam pre-reforming of natural gas at 400–550 °C, low steam-to-carbon (S/C) molar ratio of 1.5, and atmospheric pressure. The obtained samples were characterized by Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, temperature-programmed reduction (TPR), temperature-programmed oxidation (TPO), hydrogen chemisorption, and CO₂–temperature-programmed desorption (TPD). Experimental results showed that the basicity and morphology of the supports depended significantly on the synthesis method. Calcium aluminate synthesized using the new decomposition procedure showed surface area of 6.23 m² g^?1, while the surface area of those prepared by the Pechini and coprecipitation method were 1.38 and 3.76 m² g^?1, respectively. The catalytic properties of the 31 wt%Ni/12CaO–7Al₂O₃ catalysts were strongly influenced by the support preparation approach. The highest specific surface area (about 230 m² g^?1), smallest Ni particle size (8.86 nm), and highest nickel dispersion (7.48%) were observed for the catalyst whose support was synthesized by the decomposition method. Even at high gas hourly space velocity (GHSV) of 2 × 10⁵ mL \({\text{g}}^{ - 1}_{\text{catalyst}}\) h^?1, this catalyst exhibited around 100% C₂H₆ and C₃H₈ conversion at temperature above 500 °C. High catalytic stability during 60 h time on-stream was also shown. The TPO profiles of the spent catalyst demonstrated high resistance to carbon formation.     

A Novel Dielectric-Barrier-Discharge Loop Reactor for Cyanide Water Treatment

A novel dielectric-barrier-discharge (DBD) loop reactor was designed for the efficient degradation of cyanide anion (CN^?) in water. The circulation of cyanide water as a falling film through plasma gas discharge zone enhanced gas–liquid mass and energy transfer and induced formation of H₂O₂ which was associated with the efficient destruction of CN^?. It was observed that among different discharge gases, the CN^? degradation rate decreased in the order of Ar > air > H₂/air mixture. Depending on discharge voltage, the treatment time for complete removal of 100 ppm CN^? in this DBD loop reactor is in the range 120–300 min. The dose of Cu²⁺ catalyst in combination with in situ production of H₂O₂ enhanced the destruction of CN^? apparently in this DBD loop reactor. The treatment time for complete degradation of 100 ppm CN^? decreased from 180 min with Ar DBD discharge alone to 40 min with 40 mg/L dose of Cu²⁺ ion in water, making it an efficient means to degrade cyanide water.     

The study of thermal decomposition kinetics of zinc oxide formation from zinc oxalate dihydrate

This study is devoted to the thermal decomposition of ZnC₂O₄·2H₂O, which was synthesized by solid-state reaction using C₂H₂O₄·2H₂O and Zn(CH₃COO)₂·2H₂O as raw materials. The initial samples and the final solid thermal decomposition products were characterized by Fourier transform infrared and X-ray diffraction. The particle size of the products was observed by transmission electron microscopy. The thermal decomposition behavior was investigated by thermogravimetry, derivative thermogravimetric and differential thermal analysis. Experimental results show that the thermal decomposition reaction includes two stages: dehydration and decomposition, with nanostructured ZnO as the final solid product. The Ozawa integral method along with Coats–Redfern integral method was used to determine the kinetic model and kinetic parameters of the second thermal decomposition stage of ZnC₂O₄·2H₂O. After calculation and comparison, the decomposition conforms to the nucleation and growth model and the physical interpretation is summarized. The activation energy and the kinetic mechanism function are determined to be 119.7 kJ mol^?1 and G(α) = ?ln(1 – α)^1/2, respectively.     

Synthesis and thermal decomposition of neodymium(III) peroxotitanate to Nd<Subscript>2</Subscript>TiO<Subscript>5</Subscript>

Neodymium(III) peroxotitanate is used as a precursor for obtaining Nd₂TiO₅. The last one possesses numerous valuable electrophysical properties. TiCl₄, Nd(NO₃)₃·6H₂O and H₂O₂ in mol ratio 1:2:10 were used as starting materials. The reaction ambience was alkalized to pH = 9 with a solution of NH₃. The obtained neodymium(III) peroxotitanate and intermediate compounds of the isothermal heating were proved by the help of quantitative analysis and infrared spectroscopy (IRS). It has Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O composition. The absorption band observed in IRS at 831 cm^?1 relates to a triangular bonding of the peroxo group of Ti, at 1062 cm^?1—terminal groups Ti–OH and at 1491 and 1384 cm^?1—the bridging OH^?-groups Ti–O(H)–Ti. Nd₂TiO₅ was obtained by thermal decomposition of neodymium(III) peroxotitanate. The isothermal conditions for decomposition were determined on the base of differential thermal analysis, thermogravimetric and differential scanning calorimetry results in the temperature range of 20–1000 °C. The mechanism of thermal decomposition of Nd₄[Ti₂(O₂)₄(OH)₁₂]·7H₂O to Nd₂TiO₅ was studied. In the temperature range of 20–208 °C, a simultaneous decomposition of the peroxo groups by the separation of oxygen and hydrate water is conducted and Nd₄[Ti₂O₄(OH)₁₂] is obtained. From 208 to 390 °C, the terminal OH^?-groups are separated and Nd₄[Ti₂O₇(OH)₆] is formed. In the range of 390–824 °C, the bridging OH^?-groups are completely decomposed to Nd₂TiO₅. The optimal conditions for obtaining nanocrystalline Nd₂TiO₅ are 900 °C for 6 h and 20–80 nm.     

Artificial Enzyme Mimics for Catalysis and Double Natural Enzyme Co-immobilization

This work presents a new chemiluminescent (CL) probe array assay. The new type CL probe array is based on enzyme mimics of Co₃O₄–SiO₂ mesoporous nanocomposite material, which not only have an excellent catalytic effect on the luminol–H₂O₂ CL reaction in an alkaline medium but also can be used for the immobilization of enzymes. The linear range of the lactose concentration is 3.0?×?10^?7 to 1.0?×?10^?5 g mL^?1 and the detection limit is 6.9?×?10^?8 g mL^?1. β-Galactosidase and glucose oxidase were selected as a model for enzyme assays to demonstrate the applicability of Co₃O₄–SiO₂ mesoporous nanocomposite material in multienzyme immobilization. The novel bifunctional CL probe array has been successfully applied to the determination of lactose in milk.     

A novel photoelectrochemical hydrogen peroxide sensor based on nickel(II)-potassium hexacyanoferrate-graphene hybrid materials modified n-silicon electrode

A platinum (Pt) film coated n-silicon (Pt/n-n⁺-Si) was modified with nickel(II)-potassium hexacyanoferrate (NiHCF)-graphene sheets (GS) hybrid and used as a photo-electrochemical (PEC) sensor for non-enzyme hydrogen peroxide (H₂O₂) detection. A NiHCF film was deposited on the surface of GS/Pt/n-n⁺-Si electrode by chemical method. The structure and composition of the NiHCF film was characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). PEC behavior of the NiHCF-GS/Pt/n-n⁺-Si electrode was investigated using cyclic voltammetry (CV) under illumination. The modified electrode has been used as PEC sensor for H₂O₂ detection with a linear range of 2.0 × 10^?6–2.9 × 10^?3 M and a detection limit of 1.0 × 10^?6 M at a signal-to-noise ratio of 3 in a two-electrode cell with a Pt plate as counter electrode. The characteristics of GS layer have been discussed in both the improvement of sensibility and selectivity.     

Effects of humidity and temperature on the electrochemical activities of H2/O2 PEMFCs using hybrid membrane electrolytes

Electrochemical characteristics of single cell performances at various humidity conditions and constant temperatures of 40?100 °C using membrane electrode assemblies (MEAs) were studied. The MEAs consist of alternative proton-conducting hybrid membrane electrolyte and noble Pt/C catalyst for the H₂/O₂ proton exchange membrane fuel cells (PEMFCs). The function of humidity on the cell performances was investigated at larger current density values of 501 mA cm^?2 and constant cell temperatures of 80 and 90 °C and the relative humidity of 100 %. The power density value of 400 mW cm^?2 was obtained when the same MEA at similar operating conditions was used. The effects of temperature on the single cell performances were investigated at various temperature ranges of 40–100 °C and constant relative humidity of 50, 70, and 100 %. The maximum current density and power density values of about 600 mA cm^?2 and 160 mW cm^?2, respectively, were obtained at 90 °C with 100 % RH. The results were compared with the reported results of Nafion membrane and similar hybrid membranes operating at low temperatures for H₂/O₂ fuel cells. Finally, the results provided an alternative proton-conducting electrolyte as promising candidate for low/intermediate temperature operating H₂/O₂ fuel cells.