3D nanomaterial silica aerogel via diffusion of chiral compound driven broadband reflection in chiral nematic liquid crystals

In the study, a novel method of broadening the bandwidth by fabricating the silica aerogel film composited with the chiral nematic liquid crystal (N*-LC) is proposed. Diffusion of chiral compound filled in the silica aerogel resulted in the non-uniform pitch distribution, which can be anchored by UV-radical polymerisation. The results strongly suggested that the reflection bandwidth could be broadened preferably by adjusting the silica aerogel condensation time, the content of UV polymerisable free radical monomer and the polymerisation temperature. The reflection bandwidth was broadened from 270 nm to 878 nm, and the centre wavelength was blue-shifted by 642 nm. A general correlation among the silica aerogel condensation time, the polymerisation condition, and the reflective region will be outlined.     

Broadband reflective liquid crystal films induced by facile temperature-dependent coexistence of chiral nematic and TGB phase

A wide pitch gradient covering the near infrared region (750.0–2500.0 nm) were facilely obtained by simple controlling temperature difference to LC mixtures with a twist grain boundary (TGB)–N* phase transition. After the pitch gradient formed, the structure of broad reflective bandwidth was fixed through polymerisation of monomers in mixtures by UV irradiation. It was found that the temperature difference between the up and down side of the samples was critical to form wide-pitch gradient distribution. Additionally, the reflection wavelength and bandwidth of films could be adjusted by the applied temperature difference with the widest bandwidth up to 1750 nm. This simple method for the preparation of broad reflective films was expected to be used in the fields like architectural energy conservation or infrared shield.     

Near-infrared DC approach by Bi<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript> co-doped YAG phosphor

Bi³⁺–Yb³⁺ ion pair co-doped YAG phosphors were successfully synthesized using conventional solid state reaction method varying the concentration of Yb³⁺ ions from 0.5 to 10 mol%. The optimum phosphors were characterized by powder X-ray diffraction (XRD), and surface morphology was studied with a scanning electronic microscope (SEM). The photoluminescence (PL) properties were studied with a spectrophotometers in near infrared (NIR) and ultraviolet visible (UV-Vis) regions. The synthesized phosphors can convert a photon of UV region (330 nm) into photons of NIR region (979 and 992 nm). The co-operative energy transfer (CET) was studied using a time decay curve and PL spectra. The theoretical value of quantum efficiency (QE) was calculated from steady time decay measurement, and the maximum efficiency approached up to 166.91 %. Hence, this phosphor could be used as a downconversion (DC) luminescent convertor in front of crystalline silicon solar cell (c-Si) panels to reduce heat loss due to spectral mismatch of the solar cells.     

Resonance Light Scattering Method for Study on the Interaction Between Fluorinated Surfactant Potassium Perfluorooctanesulfonate and DNA

Resonance light-scattering (RLS) characteristics of the interactions between fluorinated surfactant potassium perfluorooctanesulfonate (PFOS) with calf thymus nucleic acid (ct DNA) were studied. After DNA was added, aggregation of PFOS on the molecular surface of DNA occurred in the pH 3.5 ～6.0, which resulted in an enhanced RLS peak at 370 nm. The RLS intensity was found to be proportional to the concentration of DNA. The determination limit was 20.0 μg · L^?1. UV-visible (UV-vis) spectra and infrared (IR) spectra both proved the binding changed the confromation of DNA.     

Preparation of nanoparticles and hollow spheres of ��-Fe2O3 and their properties

Uniform nanoparticles and hollow microspheres of hematite (??-Fe₂O₃) were obtained via a hydrothermal method by using iron (III) chloride as a precursor. The effects of reactant concentration, reaction time and temperature on the morphology of the samples were studied. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and superconducting quantum interference device magnetometer (SQUID) measurement. ??-Fe₂O₃ nanoparticles show a superparamagnetic behavior and the average size of the spherical particles was around 60 nm. However, hollow microspheres show a normal ferromagnetic behavior at room temperature with remanent magnetization and coercivity of 0.2482 emu/g and 2,516 Oe, respectively, and their average diameter was around 2 ??m. The effects of reactant concentration and reaction temperature on the formation of the products were investigated. The experimental results reveal that the magnetic properties of hematite can be tuned by controlling the morphology.     

纳米结构钴薄膜电极的制备及其异常红外性能研究

用循环伏安电沉积法在玻碳基底上制备纳米结构钴薄膜, 扫描电子显微镜研究结果表明, 纳米结构钴薄膜主要由平均粒径为150 nm的钴粒子组成, 同时还有为数不多的粒径在400~500 nm的钴粒子. 以CO为探针分子, 结合原位傅里叶变换红外反射光谱研究结果, 发现所制备的纳米结构钴薄膜具有异常红外效应. 吸附态CO发生异常红外吸收, 谱峰增强了26.2倍, 测得线型吸附态COL的Stark系数为77.5 cm-1·V-1.     

Radioanalytical prediction of radiative capture in 99Mo production via transmutation adiabatic resonance crossing by cyclotron

In this study, the transmutation adiabatic resonance crossing (TARC) concept was estimated in ⁹⁹Mo radioisotope production via radiative capture reaction in two designs. The TARC method was composed of moderating neutrons in lead or a composition of lead and water. Additionally, the target was surrounded by a moderator assembly and a graphite reflector district. Produced neutrons were investigated by (p,xn) interactions with 30 MeV and 300 μA proton beam on tungsten, beryllium, and tantalum targets. The ⁹⁹Mo production yield was related to the moderator property, cross section, and sample positioning inside the distinct region of neutron storage as must be proper to achieve gains. Gathered thermal flux of neutrons can contribute to molybdenum isotope production. Moreover, the sample positioning to gain higher production yield was dependent on a greater flux in the length of thermal neutrons and region materials inside the moderator or reflector. When the sample radial distance from Be was 38 cm inside the graphite region using a lead moderator design, the production yield had the greatest value of activity, compared with the other regions, equal to 608.72 MBq/g. Comparison of the two designs using a Be target revealed that the maximum yield occurred inside the graphite region for the first design at 38 cm and inside the lead region for the second design at 10 cm. The results and modeling of the new neutron activator were very encouraging and seem to confirm that the TARC concept can be used for ⁹⁹Mo production in nuclear medicine.     

Synthesis of highly pure nanocrystalline and mesoporous CaTiO3 by a particulate sol–gel route at the low temperature

The low temperature perovskite-type calcium titanate (CaTiO₃) thin films and powders with nanocrystalline and mesoporous structure were prepared by a straightforward particulate sol–gel route. The prepared sol had a narrow particle size distribution about 17 nm. X-ray diffraction and Fourier transform infrared spectroscopy revealed that, the synthesized powders had highly pure and crystallized CaTiO₃ structure with preferable orientation growth along (1 2 1) direction at 400–800 °C. The activation energy of crystal growth was calculated 5.73 kJ/mol. Furthermore, transmission electron microscope images showed that the average crystallite size of the powders annealed at 400 °C was around 3.5 nm. Field emission scanning electron microscope analysis and atomic force microscope images revealed that, the deposited thin films had uniform, mesoporous and nanocrystalline structure with the average grain size in the range 33–39 nm depending on annealing temperature. Based on Brunauer–Emmett–Teller (BET) analysis, the synthesized powders showed mesoporous structure with BET surface area in the range 51–21 m²/g at 400–800 °C. One of the smallest crystallite size and one of the highest surface areas reported in the literature is obtained which can be used in many applications, such as photocatalysts.     

The properties of silica nanoparticles with high monodispersity synthesized in the microreactor system

A new combined micromixer/microreactor/batch reactor system for the synthesis of monodisperse silica particles was demonstrated, which showed superiorities over the batch reactor. The silica nanoparticles with different sizes (ranging from 20 nm to 2 μm) and size distributions could be controllably synthesized by varying the reaction temperature and reaction time. The narrowest size distribution of the silica particles was synthesized at 60 °C. The transmission electron microscopy characterization showed that the sphericities of silica particles got better as the particle size increased. Thermal gravimetry–differential thermal analysis and Fourier transform infrared characterization indicated that the amount of ethoxy groups of silica particles decreased and the hydroxyl groups increased with the reaction time increasing. And the hydroxyl groups in silica particles increased with the reaction temperature rising.     

Tolane liquid crystals bearing fluorinated terminal group and their mid-wave infrared properties

This paper describes the synthesis and characterisation of several liquid crystal (LC) compounds having a tolane core structure and a trifluoromethoxy terminal group. The mesomorphic properties, mid-wave infrared (IR) absorption and birefringence were investigated. These materials exhibit low absorption in mid-wave IR regions (MWIR) and high birefringence (Δn ~ 0.26–0.29). The impact of fluorine substitution was investigated. Compounds with monofluorine exhibit wide mesophase temperature (88.5°C), and the mesomorphic behaviour weakened with increasing fluorine atom. The results show that they are promising LC materials for applications in the MWIR.     

Ficus carica Latex-Mediated Synthesis of Silver Nanoparticles and Its Application as a Chemophotoprotective Agent

The present work provides scientific support on the use of latex of Ficus carica to synthesize stable silver nanoparticles (AgNPs). AgNPs synthesized immediately after the addition of latex to silver nitrate solution at room temperature. Synthesized nanoparticles were of spherical shape with average size of 163.7 nm. Fourier transform infrared spectroscopy analysis revealed capping of proteins and phenolic compound on AgNPs, while X-ray diffraction analysis confirmed the fcc nature of AgNPs. Particles formed were stable for a long time (6 months). It was found that incorporation of AgNPs with 2 and 4 % concentration exhibits synergistic increase in sun protection factor of commercial sunscreen and natural extracts ranging from 01 to 12,175 % than control. Further characterization of latex and AgNPs revealed total phenolic content of 98.75 and 94.88 μg/ml. The ferric ion reduction potentials of latex and AgNPs were 79.69 and 18.79 %. Reduction potential of ascorbic acid was synergistically increased after cumulative preparation of ascorbic acid with latex and AgNPs and found to be 106.76 and 101.50 % for ascorbic acid + latex and ascorbic acid + AgNPs, respectively.     

Doping-induced emission of infrared light from Co2+-doped ZnSe quantum dots

ZnSe quantum dots doped with Co²⁺ have been prepared in aqueous solution by a one-pot method using thioglycolic acid as stabilizer. The quantum dots were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), UV?Cvisible spectrophotometry, and spectrofluorimetry. The results confirmed the quantum dots formed a single cubic phase with zinc blende structure. The average particle size of the quantum dots was approximately 5 nm. Co²⁺ ions were doped into ZnSe lattice sites by substitution. As a result, infrared (IR) emission of Co^{2+ 4}T₂(F) ?? ⁴A₂(F) at approximately 3.5 ??m was detected on excitation with 755 nm radiation.     

Terbinafine hydrochloride intercalated in montmorillonite: synthesis and characterization

The novel antifungal hybrid of terbinafine hydrochloride (TER-HCl)/montmorillonite was synthesized by the intercalation method under mechanical stirring. Intercalation of TER-HCl in the MMT galleries was characterized by X-ray diffraction (XRD), Fourier transform infrared spectra, elemental analysis (EA). and thermogravimetric analysis (TGA). The results from IR, TGA, and EA showed a difference in chemical composition of the MMT and the TER-HCl/MMT. XRD analysis showed that the basal spacing of montmorillonite significantly expanded from 1.53 to 2.79 nm. TER-HCl was successfully intercalated into the interlayer of MMT, and 28 % of TER-HCl was released after 48 h in 0.9 % (w/v) NaCl aqueous solution (pH 7) at 37 ± 0.5 °C. The antifungal activity of the hybrid against Candida albicans was evaluated using the inhibitory zone method and the minimum inhibitory concentration. The TER-HCl/MMT strongly inhibited C. albicans. These results show that TER-HCl/MMT can be useful in biomedical applications.     

Low temperature nanostructured lithium titanates: controlling the phase composition, crystal structure and surface area

Low temperature lithium titanate compounds (i.e., Li₄Ti₅O₁₂ and Li₂TiO₃) with nanocrystalline and mesoporous structure were prepared by a straightforward aqueous particulate sol–gel route. The effect of Li:Ti molar ratio was studied on crystallisation behaviour of lithium titanates. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) revealed that the powders were crystallised at the low temperature of 500 °C and the short annealing time of 1 h. Moreover, it was found that Li:Ti molar ratio and annealing temperature influence the preferable orientation growth of the lithium titanate compounds. Transmission electron microscope (TEM) images showed that the average crystallite size of the powders annealed at 400 °C was in the range 2–4 nm and a gradual increase occurred up to 10 nm by heat treatment at 800 °C. Field emission scanning electron microscope (FE-SEM) analysis revealed that the deposited thin films had mesoporous and nanocrystalline structure with the average grain size of 21–28 nm at 600 °C and 49–62 nm at 800 °C depending upon the Li:Ti molar ratio. Moreover, atomic force microscope (AFM) images confirmed that the lithium titanate films had columnar like morphology at 600 °C, whereas they showed hill-valley like morphology at 800 °C. Based on Brunauer–Emmett–Taylor (BET) analysis, the synthesized powders showed mesoporous structure containing pores with needle and plate shapes. The surface area of the powders was enhanced by increasing Li:Ti molar ratio and reached as high as 77 m²/g for the ratio of Li:Ti = 75:25 at 500 °C. This is one of the smallest crystallite size and the highest surface areas reported in the literature, and the materials could be used in many applications such as rechargeable lithium batteries and tritium breeding materials.     

Synthesis and characterization of palladium–tin bicolloids prepared by chemical liquid deposition

Palladium–tin bicolloids have been prepared by chemical liquid deposition. The metals were cocondensed at 77 K with ethanol, 2-propanol, 2-methoxyethanol, 2-butanone and acetone. The distribution of particle sizes was determined by transmission electron microscopy of the stables dispersions. The sizes ranged from 3.8 nm for 2-methoxyethanol to 8.3 nm for acetone colloids. Electrophoretic measurements such as colloid charge and zeta potential were achieved. lt was found that the colloids possess electrical charge; therefore, it is postulated that their stability is by simple solvatation. The colloids showed stability over 1 week at room temperature. The zeta-potential values are in agreement with the stability and electrophoretic mobility. The highest zeta potential was obtained for PdSn–2-methoxyethanol colloids with 379 mV and the lowest for 2-butanone with 114 mV. The colloids exhibit absorption bands in the UV region. In the visible region no plasma absorption was found. Active solids obtained by evaporation of the solvent contain a certain amount of the solvent incorporated, and owing to their reactivity they produce a mixture of tin oxide with palladium and tin. The presence of solvents can be observed by Fourier transform IR incorporation in the finely divided solids. Characteristic bands for each solvent were measured. By means of thermogravimetric analysis and differential scanning calorimetry the thermal stability of the solids and the transition heat give us the carbonaceous residues in the films. The elemental analysis of the powders was carried out.     

Differentiation Between Anti-Epidermal Growth Factor Receptors Antibody Conjugated and Unconjugated Gold Nanoparticles Using Attenuated Total Reflectance–Fourier Transform Infrared Spectroscopy

Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) along with UV-Vis was used to distinguish between structural differences between a normal human breast cell line (MCF-12 F) and a cancerous breast cell line (MCF-7) after both being treated with conjugated gold nanoparticles and unconjugated gold nanoparticles. The MCF-7 cell line possessed a small amount of epidermal growth factor receptors (EGFR) on its cell surface whereas the MCF-12 F cell line did not. The anti-EGFR antibodies blocked the binding of epidermal growth factors to this receptor which plays an important role in the regulation of cell growth, proliferation, and differentiation. The infrared (IR) spectra for both cell lines yield several differences between normal biological samples and cancerous samples. As the malignancy of the sample increases, the peak intensity and wavenumber positions decrease. The same conclusion was drawn from thin-layers of conjugated nanoparticles and nonconjugated nanoparticles. The presence of conjugated nanoparticles increased the peak intensity of the MCF-7 cell line whereas it decreased the peak intensity for the MCF-12 F cell line. UV-Vis was used to show the presence of the anti-EGFR antibodies on the surface of the gold nanoparticles which was 5 nm red shifted compared to the gold nanoparticles solution.     

Influence and correction of peak shift and band broadening observed by rank analysis on vibrational bands from variable-temperature measurements

Variable-temperature infrared (IR) spectra of cyclohexane and IR and Raman spectra of chlorocyclohexane have been investigated by graphic eigenvalue analysis. Thermal effects known as peak shift and band broadening combined with heteroscedastic noise in vibrational bands are found to have severe influence on the interpretation of the outcome of rank analysis. Methods for correction of frequency shifts and band broadening in the spectral profiles due to temperature variation are developed and tested.     

Study on Light Aging of Silk Fabric by Fourier Transform Infrared Spectroscopy and Principal Component Analysis

To investigate environmental effect on cultural materials, Fourier transform infrared technique (FTIR/ATR) was applied to analyze the silk aging process. Changes in chemical and conformational structures of silk fabric undergoing ultraviolet induced degradation were investigated. The IR spectra provided strong bands of photosensitive amide I, II, and III. For overlapping amide III region, both of the original and second-derivative IR spectra revealed that UV irradiation induced the structural transformation from β-sheet domain to β-turn conformation, which was supported by the increase of β-turn marker band at 1015 cm^?1 associated with polyglycine. Additionally the reduced bands associated with (GlyAla)_n segment at 1000 and 976 cm^?1, and the decreased band at 1070 cm^?1 related to β-sheet structure also illustrated the conformational transition. Furthermore, we applied a chemometric method of principal component analysis for the evaluation of silk degradation based on variations in amide I spectral region. The score plot using the first two principal components effectively summarized the general trend of silk-aging and revealed the quick degradation appeared in the initial stages (12 h and 24 h) and the 108-hr stage. This work provides a potential novel application of the infrared spectroscopy in noninvasive qualitative and quantitative investigation of silk degradation.     

Laser Based Optical Emission Studies of Zinc Oxide (ZnO) Plasma

We present the optical emission characteristics of the zinc oxide (ZnO) plasma produced by the first (1,064 nm) and second (532 nm) harmonics of a Q switched Nd: YAG laser. The target material was placed in front of laser beam in air (at atmospheric pressure).The experimentally observed line profiles of neutral zinc (Zn I) have been used to extract the electron temperature using the Boltzmann plot method, whereas, the electron number density has been determined from the Stark broadening. The electron temperature is calculated by varying distance from the target surface along the line of propagation of plasma plume and also by varying the laser irradiance. Beside we have studied the variation of number density as a function of laser irradiance as well as its variation with distance from the target surface. It is observed that electron temperature and electron number density increases as laser energy is increased.     

Gradual Growth of Gold Nanoseeds on Silica for Silica@Gold Core–Shell Nano Applications by Two Different Methods: A Comparison on Structural Properties

This paper describes the homogeneous growth of gold shells on the surfaces of spherical dielectric silica nanoparticle cores by two different approaches: common two-step method (the name) and deposition–precipitation process. The methods basically are different in forming the precursor gold seed particles on silica. The structural and optical properties and morphology of the nanoparticles were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), UV–Vis spectrophotometery, and photo luminescence spectroscopy (PL). The results showed that, although in both the methods the core–shell nanoparticles can be reliably prepared in a controlled fashion with a favorable uniformity, but deposition–precipitation method indicated a better mechanical stability while it was more cost and time effective too. A regular red shift, from 488 to 662 nm, and peak broadening was also risen for the striking plasmon absorption peak as gold nanoseeds created by each of the two methods grew in size on silica cores.