Magnetic Behaviour and Heating Effect of Fe3O4 Ferrofluids Composed of Monodisperse Nanoparticles

Fe3O4 ferrofluids containing monodisperse Fe3O4 nanoparticles with different diameters of 8, 12, 16 and 18nm are prepared by using high-temperature solution phase reaction. The particles have single crystal structures with narrow size distributions. At room temperature, the 8-nm ferrofluid shows superparamagnetic behaviour, whereas the others display hysteresis properties and the coercivity increases with the increasing particle size. The spin glass-like behaviour and cusps near 190K are observed on all ferrofluids according to the temperature variation of field-cooled （FC） and zero-field-cooled （ZFC） magnetization measurements. The cusps are found to be associated with the freezing point of the solvent. As a comparison, the ferrofluids are dried and the FC and ZFC magnetization curves of powdery samples are also investigated. It is found that the blocking temperatures for the powdery samples are higher than those for their corresponding ferrofluids. Moreover, the size dependent heating effect of the ferrofluids is also investigated in ac magnetic field with a frequency of 55 kHz and amplitude of 200 Oe.     

Synthesis and magnetic properties of spinel CoFe2O4 nanowire arrays

Spinel CoFe₂O₄ nanowire arrays were synthesized in nanopores of anodic aluminum oxide (AAO) template using aqueous solution of cobalt and iron nitrates as precursor. The precursor was filled into the nanopores by vacuum impregnation. After heat treatment, it transformed to spinel CoFe₂O₄ nanowires. The structure, morphology and magnetic properties of the sample were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The results indicate that the nanowire arrays are compact. And the individual nanowires have a high aspect ratio, which are about 80 nm in diameter and 10 μm in length. The nanowires are polycrystalline spinel phase. Magnetic measurements indicate that the nanowire arrays are nearly magnetic isotropic. The reason is briefly discussed. Moreover, the temperature dependence of the coercive force of the nanowire arrays was studied.     

Synthesis and magnetic properties of antiferromagnetic Co3O4 nanoparticles

Antiferromagnetic Co₃O₄ nanoparticles with diameter around 30 nm have been synthesized by a solution-based method. The phase identification by the wide-angle X-ray powder diffraction indicates that the Co₃O₄ nanoparticle has a cubic spinel structure with a lattice constant of 0.80843(2) nm. The image of field emission scanning electron microscope shows that the nanoparticles are assembled together to form nanorods. The magnetic properties of Co₃O₄ fine particles have been measured by a superconducting quantum interference device magnetometer. A deviation of the Néel temperature from the bulk is observed, which can be well described by the theory of finite-size scaling. An enhanced coercivity as well as a loop shift are observed in the field-cooled hysteresis loop. The exchange bias field decreases with increasing temperature and diminishes at the Néel temperature. The training effect and the opening of the loop reveal the existence of the spin-glass-like surface spins.     

Influences of Bi2O3/V2O5 Additives on the Microstructure and Magnetic Properties of Lithium Ferrite

Lithium ferrite materials with different concentrations of Bi2O3 and V2O5 additives are prepared by the conventional ceramic technique. The x-ray diffraction analysis proves that the additives do not affect the final crystal phase of the lithium ferrite in our testing range. Both Bi2O3 and V2O5 additives could promote densification and lower sintering temperature of the lithium ferrite. The average grain size first increases, and then gradually decreases with the Bi2O3 content. The maximal grain size appears with 0.25 wt% Bi2O3. The average grain size first increases, and then is kept almost unchanged with the V2O5 content. The maximal average grain size of the samples with V2O5 additive is much smaller than that of the samples with Bi2O3 additive. Furthermore, the V2O5 additive more easily enters the crystal lattice of the lithium ferrite than the Bi2O3 additive. These characteristics evidently affect the magnetic properties, such as saturation flux density, ratio of remanence Br to saturation flux density Bs, and coercive force of the lithium ferrite. The mechanisms involved are discussed.     

Permeability-frequency spectra of (Fe1−xcox)73.5Cu1Nb3Si13.5B9 nanocrystalline alloys under different magnetic fields

Under various amplitude of AC magnetic fields domain wall motion is the main mechanism in the magnetization process. This includes domain wall bulging and domain wall displacing. In this paper complex permeability-frequency spectra of (Fe_1−xCo_x)_73.5Cu₁Nb₃Si_13.5B₉ (x=0,0.5$x=0,0.5$) nanocrystalline alloys were measured as a function of the AC magnetic field, ranging from 0.001 to 0.04 Oe. Obvious changes have been found in complex permeability spectra for alloy x=0$x=0$ with the change of the amplitude of AC magnetic field, but variation of AC magnetic field has little effect on complex permeability spectra for alloy x=0.5$x=0.5$. This is attributed to the increased pinning field after substitution of Fe with Co in Fe_73.5Cu₁Nb₃Si_13.5B₉ nanaocrystalline alloy.     

Fabrication and magnetic properties of Fe3O4 nanowire arrays in different diameters

Fe₃O₄ nanowire arrays with different diameters of D=50, 100, 150 and 200 nm were prepared in anodic aluminum oxide (AAO) templates by an electrodeposition method followed by heat-treating processes. A vibrating sample magnetometer (VSM) and a Quantum Design SQUID MPMS magnetometer were used to investigate the magnetic properties. At room temperature the nanowire arrays change from superparamagnetism to ferromagnetism as the diameter increases from 50 to 200 nm. The zero-field-cooled (ZFC) and field-cooled (FC) magnetization measurements show that the blocking temperature T_B increases with the diameter of nanowire. The ZFC curves of D=50 nm nanowire arrays under different applied fields (H) were measured and a power relationship between T_B and H were found. The temperature dependence of coercivity below T_B was also investigated. Mössbauer spectra and micromagnetic simulation were used to study the micro-magnetic structure of nanowire arrays and the static distribution of magnetic moments of D=200 nm nanowire arrays was investigated. The unique magnetic behaviors were interpreted by the competition of the demagnetization energy of quasi-one-dimensional nanostructures and the magnetocrystalline anisotropy energy of particles in nanowires.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Magnetic and Distribution of Magnetic Moments in Amorphous Fe89.7P10.3 Alloy Nanowire Arrays

Binary amorphous Fe89.7P10.3 alloy nanowire arrays in been fabricated in an anodic aluminium oxide template diameter of about 40nm and length of about 3μm have by electrodeposition. Magnetic properties of the samples are investigated by mean of vibrating sample magnetometer, transmission Mossbauer spectroscopy and conversion electron Mossbauer spectroscopy at room temperature. It is found that the nanowire arrays have obvious perpendicular magnetic anisotropy, and are ferromagnetic at room temperature, with its Mossbauer spectra consisting of six broad lines. The average angles between the Fe and 28° at the end of the amorphous Fe89.7P10.3 alloy magnetic moment and the wire axis are about 14°inside nanowire arrays, respectively. The magnetic behaviour is decided by the shape anisotropy and the dipolar interaction between wires. In addition, the magnetic moments distribution is theoretically demonstrated by using the symmetric fanning mechanism of the spheres chain model.     

Non-linear response of driven spin excitations

Brillouin scattering was used to study the effect of high-power microwave fields on an array of permalloy particles and the results are compared with simulations. The simulations are of two types: one is based on a model in which each particle is treated as a single spin, the second model relies on generalized micromagnetic codes that include external driving fields and enable magnon–magnon coupling. Experimental results as well as simulations show clear, but sometimes different, evidence of non-linear behavior.     

Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Synthesis and magnetic properties of CoFe2O4 ferrite nanoparticles

CoFe₂O₄ ferrite nanoparticles were prepared by a modified chemical coprecipitation route. Structural and magnetic properties were systematically investigated. X-ray diffraction results showed that the sample was in single phase with the space group . The results of field-emission scanning electronic microscopy showed that the grains appeared spherical with diameters ranging from 20 to 30 nm. The composition determined by energy-dispersive spectroscopy was stoichiometry of CoFe₂O₄. The Curie temperature in the process of increasing temperature was slightly higher than that in the process of decreasing temperature. This can be understood by the fact that heating changed Co²⁺ ion redistribution in tetrahedral and in octahedral sites. The coercivity of the synthesized CoFe₂O₄ samples was lower than the theoretical values, which could be explained by the mono-domain structure and a transformation from ferrimagnetic to superparamagnetic state.     

Experimental analysis of the fast magnetization dynamics in high perpendicular anisotropy Co/Pt nanostructures

We present preliminary results for magnetization dynamics in high perpendicular anisotropy Co/Pt cross-shaped nanostructures submitted to a single/train out-of-plane field pulses. For this, a fabrication process has been developed to obtain high-quality microwave test structures. Using extraordinary Hall effect, we measure quasistatic hysteresis loops while applying either a single or a train of field pulses of given amplitude (32 mT at maximum), variable duration (0.2–10 ns) and repetition frequency (1–100 kHz). We get that field pulses affect only one side of the hysteresis loops without any clear change in the squareness of the loop. Such behavior can be most probably attributed to pulse-induced nucleation of reverse domains in the cross area. The measured shift in coercive field decreases linearly with the logarithm of the pulse duration and two switching regimes that get connected for pulse duration around 1 ns have been observed. Switching probability with single pulse showed that field pulse of 10 ns and 32 mT of magnitude has the same effect of 2 mT static fields.     

Magnetic structure and phase diagram of the frustrated spinel Cd1−xZnxCr2Se4

In attempt to characterise the magnetic ordering in the whole composition range of the Cd_1−xZn_xCr₂Se₄ system, various magnetic measurements were performed on both crystalline and polycrystalline samples with 0?x?1. The magnetic properties of the system are typical of a ferromagnet below x=0.4 and of a complex antiferromagnet one above x=0.6. In this work the intermediate region was carefully studied. The variations of both M(T) and χ_ac at low fields suggest that transitions from ferromagnetic to Gabay–Toulouse ferromagnetic-spin-glass mixed phase at low temperature occur in the range 0.41?x?0.58. The high-temperature susceptibility measurements show that for the whole concentration range the system obeys Curie–Weiss laws. The results can be explained by the coexistence of competing interactions (ferromagnetic between nearest neighbours and antiferromagnetic between higher order neighbours) and disorder due to the random substitution between zinc and cadmium ions in the tetrahedral sites of the spinel lattice. An experimental magnetic phase diagram of the system is established.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

High-frequency magnetic properties and attenuation characteristics for barium ferrite composites

High-frequency magnetic properties and attenuation characteristics for barium-ferrite/epoxy composites have been studied. The methods for increasing μ′ and μ″ and controlling f_R, including ion substitution, doping of small amount of oxides, effect of damping, as well as the modification of particle sizes and shapes, are introduced. The results show that the composites are potential candidates for use as electromagnetic (EM) attenuation materials with low reflectivity and broad bandwidth at 2-18 GHz.     

Effects of precursor types of Fe and Ni components on the properties of NiFe2O4 powders prepared by spray pyrolysis

The effects of the precursor types of Ni and Fe components on the morphology, mean size, and magnetic property of NiFe₂O₄ powders prepared by spray pyrolysis from the spray solution, with citric acid were studied. The precursor powders with hollow and thin wall structure turned to the nano-sized NiFe₂O₄ powders after post-treatment at a temperature of 800 °C. The nickel ferrite powders obtained from the spray solution with ferric chloride had nanometer sizes and narrow size distributions irrespective of the types of nickel precursor. The nickel ferrite powders obtained from the spray solution with ferric nitrate and nickel chloride also had nanometer size and narrow size distribution. The saturation magnetizations of the NiFe₂O₄ powders changed from 37 to 42 emu/g according to the types of the Fe and Ni precursors. The saturation magnetizations of the NiFe₂O₄ powders increased with increasing the Brunauer-Emmett-Teller (BET) surface areas of the powders.     

High-frequency response of nanostructured magnetic materials

This paper reports a brief overview on recent developments regarding the high-frequency response in the GHz range of nanostructured magnetic materials. Emphasis is placed on the linear regime in the frequency domain characterized by the dynamic susceptibility spectrum. Some modeling tools and experimental probes allowing determination of the dynamic susceptibility spectrum are first rapidly reviewed and their respective advantages and disadvantages are discussed. Next, some illustrative examples of the high-frequency response of nanopatterned materials based on recent works are presented. The role played by the shape of the element on the characteristics of excitation spectrum is underlined. Lastly, some prospects are proposed and promising trends are highlighted.     

Mössbauer studies on the superparamagnetic behavior of CoFe2O4 with a few nanometers

CoFe₂O₄ nanoparticles with a cubic spinel structure are prepared by a high-temperature thermal decomposition method. The average particle sizes are 4.6  and 5.7 nm for CoFe₂O₄ made with two kinds of solvents by TEM. Mössbauer spectra of 4.6 nm particles displayed a superparamagnetic behavior as demonstrated by a single line with zero hyperfine fields, but that of 5.7 nm particles did not at room temperature. It is considered that anisotropy energy was still more superior to thermal energy because of particle size of 5.7 nm CoFe₂O₄. Furthermore, Mössbauer spectra exhibited the typical spectrum shapes of the CoFe₂O₄ at 4.2 K. The spectrum at 4.2 K was fitted using two magnetic components of hyperfine fields _Hhf=540.4,512.6$H_{\mathrm{hf}}=540.4,512.6$ kOe and isomer shifts δ=0.40,0.30$\delta =0.40,0.30$ mm/s for 4.6 nm and _Hhf=542.7,512.8$H_{\mathrm{hf}}=542.7,512.8$ kOe and δ=0.41,0.29$\delta =0.41,0.29$ mm/s for 5.7 nm corresponding to Fe³⁺ ions at site A and site B, respectively.     

Solid state reaction synthesis of NiFe2O4 nanoparticles

Ni-ferrite (NiFe₂O₄) nanoparticles have been synthesized via a solid state reaction process. Ni and Fe bi-metallic nanoparticles in the form of Ni₃₃Fe₆₇ alloy nanopowder are first synthesized by simultaneous evaporation of the required amounts of pure Ni and Fe metals followed by rapid condensation of the evaporated metal flux into solid state by means of an inert gas, helium, using the process of inert gas condensation (IGC). In order to form the NiFe₂O₄ structure, as-synthesized samples (Ni₃₃Fe₆₇) are annealed for 12 h in ambient conditions at different annealing temperatures. Structural analyses show that NiFe₂O₄ starts to form at around 450 °C and gets progressively well defined with increasing annealing temperatures yielding particle with size ranging between 15 and 50 nm. Besides successfully forming NiFe₂O₄, NiO/Fe₃O₄ core/shell nanoparticles have also been synthesized by adjusting the annealing conditions. Three different structures, Ni₃₃Fe₆₇, NiO/Fe₃O₄, and NiFe₂O₄, obtained in this study are compared with respect to their structural and magnetic properties.     

Relations,analogous to Snoek's one,for domain wall processes

The suitability of relations having a formal similarity with the known Snoek's law is analysed for polycrystalline ferrites (PF) in their typical domain wall process frequency range. The parameters used in these relations are the saturation magnetization and those taken from the complex permeability spectrum and from microstructure of PF sample.