Azide telechelics chain extended by click reaction: Synthesis,characterization, and cross‐linking

Azide telechelics of poly(dimethylsiloxane) (PDMS), polypropylene oxide (PPO), and polyethylene oxide (PEO) were synthesized from the corresponding epoxy telechelics and characterized. These oligomeric azides were chain extended by reaction with bispropargyl ether of bisphenol A (BPEBA) through a copper‐catalyzed azide‐alkyne cycloaddition (CuAAC) reaction. PDMS manifested a faster reaction in contrast to PPO or PEO. The chain‐extended polymers underwent cross‐linking above 170°C through thermal cleavage of residual (terminal) azide groups. This was manifested in their rheograms and was further substantiated by FTIR and NMR spectroscopic analyses. Dynamic mechanical analyses of the cross‐linked polymers exhibited characteristic transitions of hard and soft segments, implying microphase separation in the system. Microscopic evaluation of the thermally cross‐linked sample revealed a porous morphology with microsized to nanosized pores.     

Hydrophilic poly(ethylene oxide)–aramide segmented block copolymers

The present paper discusses block copolymers with segments of either poly(ethylene oxide), poly(propylene oxide), or mixtures of poly(ethylene oxide)/poly(propylene oxide) and monodisperse aramide segments. The length of the polyether segments as well as the concentration of polyethylene oxide was varied. The synthesized copolymers were analyzed by DSC, FTIR, AFM and DMTA. In addition, the hydrophilicity was studied.The crystallinity of the monodisperse aramide segments was found to be high and the crystals, dispersed in the polyether phase, displayed a nano-ribbon morphology. The PEO segments were able to crystallize and this crystalline phase reduced the low-temperature flexibility. The PEO crystallinity and melting temperature could be strongly reduced by copolymerization with PPO segments. By using mixtures of PEO and PPO segments, hydrophilic copolymers with decent low-temperature properties could be obtained.     

Synthesis and characterization of biodegradable aliphatic copolyesters with poly(ethylene oxide) soft segments

A series of multiblock poly(ether-ester)s based on poly(butylene succinate) (PBS) as the hard segments and hydrophilic poly(ethylene oxide) (PEO) as the soft segments was synthesized with the aim of developing degradable polymers which could combine the mechanical properties of high performance elastomers with those of flexible plastics. The aliphatic poly(ether-ester)s were synthesized by the catalyzed two-step transesterification reaction of dimethyl succinate, 1,4-butanediol and α,ω-hydroxyl terminated poly(ethylene oxide) (PEO, = 1000 g/mol) in bulk. The content of soft PEO segments in the polymer chains was varied from about 10 to 50 mass%. The effect of the introduction of the soft PEO segments on the structure, thermal and physical properties, as well as on the biodegradation properties was investigated. The composition and structure of these aliphatic segmented copolyesters were determined by ¹H NMR spectroscopy. The molecular weights of the polyesters were verified by gel permeation chromatography (GPC), as well as by viscometry of dilute solutions and polymer melts. The thermal properties were investigated using differential scanning calorimetry (DSC). The degree of crystallinity was determined by means of DSC and wide-angle X-ray scattering. A depression of melting temperature and a reduction of crystallinity of the hard segments with increasing content of PEO segments were observed. Biodegradation of the synthesized copolyesters, estimated in enzymatic degradation tests in phosphate buffer solution with Candida rugosa lipase at 37 °C was compared with hydrolytic degradation in the buffer solution. The weight losses of the samples were in the range from 2 to 10 mass%. GPC analysis confirmed that there were significant changes in molecular weight of copolyesters with higher content of PEO segments, up to 40% of initial values. This leads to conclusion that degradation mechanism of the poly(ether-ester)s based on PEO segments occurs through bulk degradation in addition to surface erosion.     

Poly(chloropropylmethyl-dimethylsiloxane)–polyurethane elastomers: Synthesis and properties of segmented copolymers and related zwitterionomers

A series of polyurethane block copolymers based on hydroxybutyl terminated poly(chloropropylmethyl-dimethylsiloxane) and poly(tetramethylene oxide) soft segments of molecular weights 2100 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-methylenediphenylene diisocyanate (MDI) that was chain extended with either 1,4-butanediol (BD) or N-methyldiethanolamine (MDEA). The materials chain extended with MDEA were ionized using 1,3-propane sultone. The weight fraction of the hard segments was in the range 0.30–0.45. The effect of mixed soft segments, chain extenders, and zwitterionization on the extent of phase separation and physical properties was studied by utilizing differential scanning calorimetry and dynamic mechanical, stress-strain, and Fourier Transform Infrared spectroscopy experiments. All of these short segment block copolymers showed nearly complete phase separation. The zwitterionomer materials exhibited ionic aggregation within the hard domains. Although hard segment crystallinity or ionic aggregation did not affect the morphology, hard domain cohesion was important in determining the tensile and viscoelastic properties of these elastomers.     

不同软段结构的双离子型聚氨酯离聚体

本文讨论了以聚环氧乙烷(PEO)、聚环氧丙烷(PPO)以及聚丁二烯(PBD)为软段,以4,4’-二异氰酸二苯甲烷(MDI)和N,N-二羟乙基甲胺(MDEA)为硬段的链段型聚氨酯的合成。并通过MDEA中的第三胺与Υ-丙磺内酯反应,转化为双离子型离聚体。用差示扫描量热、红外光谱、动态力学性能以及应力-应变等实验方法研究了化学组成和氨磺化程度对材料相分离程度,力学性能和形态结构的影响。结果表明,离子化后的材料力学性能有很大的改善。对PBD为软段的材料,离子化只能提高硬段“微区”的内聚能,而对PEO、PPO为软段的材料,还能大大提高软、硬相的相分离程度。     

Segmented block copolymers based on poly(propylene oxide) and monodisperse polyamide‐6,T segments

Polyether(ester amide)s with poly(propylene oxide) (PPO) and monodisperse poly(hexamethylene terephthalamide) segments were synthesized, and their structure–property relations were investigated. The length of the amide segments was varied from diamide to tetraamide to hexaamide segments, and therefore the number hydrogen bonds per amide segment increased from two to four to six. PPO was end‐capped with 20 wt % ethylene oxide and had number‐average molecular weights of 1000, 2300, and 4000 g/mol (including ethylene oxide tips). The morphology of the poly‐ether(ester amide)s was studied with transmission electron microscopy and atomic force microscopy, the thermal properties were studied with differential scanning calorimetry and dynamic mechanical thermal analysis, and the tensile properties were studied with dumbbell samples. The elastic behavior of the block copolymers was investigated with tensile and compression tests. These segmented copolymers had two sharp transitions: a glass‐transition temperature (T_g) of the PEO–PPO–PEO phase [where PEO is poly(ethylene oxide)] and a melting temperature (T_m) of the amide segments. The amide segments crystallized in nanoribbons with a high aspect ratio 1000. T_m increased with the amide segment length and with decreasing PEO–PPO–PEO content (solvent effect). The modulus increased strongly with the amide content. This modulus increase could be described by the Halpin–Tsai fiber composite model. Increasing the amide segment length surprisingly also improved the elasticity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4769–4781, 2006     

Morphology of a highly asymmetric double crystallizable poly(epsilon-caprolactone-b-ethylene oxide) block copolymer

The morphology of a highly asymmetric double crystallizable poly(epsilon-caprolactone-b-ethylene oxide) (PCL-b-PEO) block copolymer has been studied with in situ simultaneously small and wide-angle x-ray scattering as well as atomic force microscopy. The molecular masses Mn of the PCL and PEO blocks are 24,000 and 5800, respectively. X-ray scattering and rheological measurements indicate that no microphase separation occurs in the melt. Decreasing the temperature simultaneously triggers off a crystallization of PCL and microphase separation between the PCL and PEO blocks. Coupling and competition between microphase separation and crystallization results in a morphology of PEO spheres surrounded by PCL partially crystallized in lamella. Further decreasing temperature induces the crystallization of PEO spheres, which have a preferred orientation due to the confinements from hard PCL crystalline lamella and from soft amorphous PCL segments in different sides. The final morphology of this highly asymmetric block copolymer is similar to the granular morphology reported for syndiotactic polypropylene and other (co-) polymers. This implies a similar underlying mechanism of coupling and competition of various phase transitions, which is worth further exploration.     

Preparation and characterization of polypseudorotaxanes based on block-selected inclusion complexation between poly(propylene oxide)-poly(ethylene oxide)-poly(propylene oxide) triblock copolymers and alpha-cyclodextrin

A series of new polypseudorotaxanes were synthesized in high yields when the middle poly(ethylene oxide) (PEO) block of poly(propylene oxide)-poly(ethylene oxide)-poly(propylene oxide) (PPO-PEO-PPO) triblock copolymers was selectively recognized and included by alpha-cyclodextrin (alpha-CD) to form crystalline inclusion complexes (ICs), although the middle PEO block was flanked by two thicker PPO blocks, and a PPO chain had been previously thought to be impenetrable to alpha-CD. X-ray diffraction studies demonstrated that the IC domains of the polypseudorotaxanes assumed a channel-type structure similar to the necklace-like ICs formed by alpha-CD and PEO homopolymers. Solid-state CP/MAS (13)C NMR studies showed that the alpha-CD molecules in the polypseudorotaxanes adopted a symmetrical conformation due to the formation of ICs. The compositions and stoichiometry of the polypseudorotaxanes were studied using (1)H NMR, and a 2:1 (ethylene oxide unit to alpha-CD) stoichiometry was found for all polypseudorotaxanes although the PPO-PEO-PPO triblock copolymers had different compositions and block lengths, suggesting that only the PEO block was closely included by alpha-CD molecules, whereas the PPO blocks were uncovered. The hypothesis was further supported by the differential scanning calorimetry (DSC) studies of the polypseudorotaxanes. The glass transitions of the PPO blocks in the polypseudorotaxanes were clearly observed because they were uncovered by alpha-CD and remained amorphous, whereas the glass-transition temperatures increased, because the molecular motion of the PPO blocks was restricted by the hard crystalline phases of the IC domains formed by alpha-CD and the PEO blocks. The thermogravimetric analysis (TGA) revealed that the polypseudorotaxanes had better thermal stability than their free components due to the inclusion complexation. Finally, the kinetics of the threading process of alpha-CD onto the copolymers was also studied. The findings reported in this article suggested interesting possibilities in designing other cyclodextrin ICs and polypseudorotaxanes with block structures.     

Towards microphase separation in epoxy systems containing PEO/PPO/PEO block copolymers by controlling cure conditions and molar ratios between blocks. Part 2. Structural characterization

The influence of addition of poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (PEO–PPO–PEO) copolymers on final morphologies of modified epoxy matrices has been investigated as a function of PEO:PPO molar ratio and cure conditions by comparison with the cured epoxy blends only containing poly(ethylene oxide) (PEO) or poly(propylene oxide) (PPO) homopolymers. Atomic force microscopy (AFM) has been used to characterize structural features of blends. Whilst diglycidyl ether of bisphenol-A (DGEBA)/4,4’-diaminodiphenylmethane (DDM)/PPO system macrophase separates, the interactions between PEO and cured epoxy are responsible for miscibility of DGEBA/DDM/PEO system. Depending on PEO:PPO molar ratio, micro- or macrophase separated morphologies have been obtained for block copolymer modified epoxy matrices. Moreover, the influence of both copolymer content and cure temperature on final morphologies has also been investigated by both experimental and theoretical analysis.     

Phase behavior,crystallization, and nanostructures in thermoset blends of epoxy resin and amphiphilic star‐shaped block copolymers

This article reports thermoset blends of bisphenol A‐type epoxy resin (ER) and two amphiphilic four‐arm star‐shaped diblock copolymers based on hydrophilic poly(ethylene oxide) (PEO) and hydrophobic poly(propylene oxide) (PPO). 4,4′‐Methylenedianiline (MDA) was used as a curing agent. The first star‐shaped diblock copolymer with 70 wt % ethylene oxide (EO), denoted as (PPO‐PEO)₄, consists of four PPO‐PEO diblock arms with PPO blocks attached on an ethylenediamine core; the second one with 40 wt % EO, denoted as (PEO‐PPO)₄, contains four PEO‐PPO diblock arms with PEO blocks attached on an ethylenediamine core. The phase behavior, crystallization, and nanoscale structures were investigated by differential scanning calorimetry, transmission electron microscopy, and small‐angle X‐ray scattering. It was found that the MDA‐cured ER/(PPO‐PEO)₄ blends are not macroscopically phase‐separated over the entire blend composition range. There exist, however, two microphases in the ER/(PPO‐PEO)₄ blends. The PPO blocks form a separated microphase, whereas the ER and the PEO blocks, which are miscible, form another microphase. The ER/(PPO‐PEO)₄ blends show composition‐dependent nanostructures on the order of 10?30 nm. The 80/20 ER/(PPO‐PEO)₄ blend displays spherical PPO micelles uniformly dispersed in a continuous ER‐rich matrix. The 60/40 ER/(PPO‐PEO)₄ blend displays a combined morphology of worm‐like micelles and spherical micelles with characteristic of a bicontinuous microphase structure. Macroscopic phase separation took place in the MDA‐cured ER/(PEO‐PPO)₄ blends. The MDA‐cured ER/(PEO‐PPO)₄ blends with (PEO‐PPO)₄ content up to 50 wt % exhibit phase‐separated structures on the order of 0.5–1 μm. This can be considered to be due to the different EO content and block sequence of the (PEO‐PPO)₄ copolymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 975–985, 2006     

1H NMR spectroscopic investigations on the micellization and gelation of PEO-PPO-PEO block copolymers in aqueous solutions

The effects of temperature, polymer composition, and concentration on the micellization and gelation properties of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymers in aqueous solutions were investigated by 1H NMR spectroscopy. It was found that the temperature-dependent behavior of PPO blocks, observed as changes in chemical shift, half-height width, and integral value, could be attributed as an intrinsic tool to characterize the transition states during unimer to micelle formation. The 1H NMR spectral analysis revealed that the hydrophobic part, PPO, of the Pluronic polymers plays a more significant role in the temperature-induced micellization, whereas the transitional behavior of Pluronic polymer, i.e., from micellization to liquid crystals formation, resulted in the drastic broadening of the spectral signals for the PEO, indicating that the PEO segments play a more significant role in the crystallization process. It was also observed that the temperature-dependent changes in the half-height width of the PEO -CH2- signal are sensitive to the liquid crystalline phase formation, which could be attributed to the close packing of spherical micelles at high polymer concentrations or temperatures.     

嵌段共聚物傅里叶变换拉曼光谱

用傅里叶变换拉曼光谱(FT-Paman)研究了聚环氧乙烷-聚环氧丙烷-聚环氧乙烷(PEO-PPO-PEO)嵌段共聚物的无水样品,发现某些谱带对PEO0-PPO-PEO嵌段共聚物的结构和构象变化敏感,其中某些峰的相对强度的PPO/PEO比率和共聚物的构象有关,研究表明PluronicF68和F88具有一些反式构象的螺旋结构,PluronicP103(P123)是无规则结构,其它的嵌段共聚物处于二者之间.     

Glass transition and melting behavior of poly(ether-ester) multiblock copolymers with poly(tetramethylene isophthalate) hard segments

The glass transition and melting behavior of poly(ether-ester) multiblock copolymers with poly(tetramethylene isophthalate) (PTMI) hard segments and poly(tetramethylene oxide) (PTMO) soft segments are studied by differential scanning calorimetry (DSC) and small- and wide-angle x-ray scattering (SAXS and WAXS). Thermodynamic melting parameters for the PTMI homopolymer are estimated by WAXS and from the dependence of melting point on crystallization temperature. The melting behavior of PTMI is characterized by dual endotherms which are qualitatively representative of the original morphology, although reorganization effects are present. The composition dependence of the glass transition temperature parameters after rapid quenching from the melt are well described by mixed phase correlations for copolymers in the range 30-100 wt% hard segment. Combined with SAXS characterization at melt temperatures, a single phase melt is suggested in these materials which extends to temperatures below the hard segment melting point. © 1994 John Wiley & Sons, Inc.     

Studies on thermotropic liquid crystalline elastomers. I. Synthesis and properties of poly (amide-ester) elastomers

Three series of novel poly(amide-ester) (PAE) elastomers were prepared by direct poly-condensation from terephthalic acid (TPA), polyols (M_n = 1000 or 2000), and various diamines. The structures and thermal properties of the synthesized PAEs were examined by FTIR spectroscopy, wide angle X-ray diffraction (WAXD), differential scanning calo-rimetry (DSC), thermal optical polarized microscopy, thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). The effects of kinds and amount of diamines and the molecular weight of polyols on the thermal properties of PAEs were studied. By introducing long flexible spacers (PE-1000 or PE-2000) into the polymer main chain, all polymers showed two-phase morphology under the thermal optical microscopic observation. It was interesting that most of the synthesized polymers exhibited only one melting transition corresponding to the soft segments. The melting transition of hard segments could not be detected due to decomposition of the soft segments. However, a thermotropic liquid crystalline PAE (TLCPAE) prepared from methylhydroquinone and 2-chloro-5-methyl-phenylenediamine with PE-1000 could be obtained by lowering the melting transition temperature of the hard segment. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of polycyanoethylmethylsiloxane polyurea urethane elastomers: A study of segmental compatibility

A series of polyurea urethane block polymers based on either aminopropyl-terminated polycyanoethylmethylsiloxane (PCEMS) soft segments or soft segment blends of PCEMS and polytetramethylene oxide (PTMO) were synthesized. The hard segments consisted of 4,4′-methylenediphenylene diisocyanate (MDI) chain-extended with 1,4-butanediol. The hard segment content varied from 11 to 36%, whereas the PTMO weight fraction in the soft segment blends varied from 0.1 to 0.9. The cyanoethyl side group concentration was also varied during the synthesis of the PCEMS oligomer. The morphology and properties of these polymers were studied by differential scanning calorimetry, infrared spectroscopy, dynamic mechanical and tensile testing, and small-angle x-ray scattering. These materials exhibited microphase separation of the hard and soft segments; however, attaching polar cyanoethyl side groups along the apolar siloxane chains promoted phase mixing in comparison with polydimethylsiloxane-based polyurethanes. The increased phase mixing is postulated to lead to improved interfacial adhesion and thus can account for the observed improvement in ultimate tensile properties compared with polydimethylsiloxane-based polyurethanes. Both hard segment content and cyanoethyl concentration are important factors governing the morphological and tensile properties of these polymers.     

Interaction of urea with pluronic block copolymers by 1H NMR spectroscopy

Solution 1H NMR techniques were used to characterize the interaction of urea with poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymers. The urea was established to interact selectively with the PEO blocks of the block copolymer, and the interaction sites were found not to change with increasing temperature. Such interactions influence the self-assembly properties of the block copolymer in solution by increasing the hydration of the block copolymers and stabilizing the gauche conformation of the PPO chain. Therefore, urea increases the critical micellization temperature (CMT) values of PEO-PPO-PEO copolymers, and the effect of urea on the CMT is more pronounced for copolymers with higher PEO contents and lower for those with increased contents of PPO segments.     

Synthesis and properties of comb-shaped segmented poly(urethanes) based on 1,2-propanediol derivatives

Comb-shaped segmented poly(urethanes) have been synthesized from ethers via the one-step procedure with the use of glycerol monostearate, D,L-3-octadecyloxy-1,2-propanediol, 3-tert-butoxy-1,2-propanediol, 3-benzyloxy-1,2-propanediol, and 1,2-propanediol as chain extenders. The soft segment of poly(urethanes) was derived from macrodiol (poly(tetramethylene glycol) with M _n = 1000), and 1,6-hexamethylene diisocyanate and 4,4′-cyclohexylmethane diisocyanate were used as diisocyanates. The effect of the structure of side chains located at the hard segments on the formation of hydrogen bonds in comb-shaped poly(urethanes) has been studied by IR spectroscopy. On the basis of DSC measurements, the glass transition temperatures of the soft and hard segments and the temperature and enthalpy of melting of the crystalline phase have been estimated and the microphase separation of segments has been assessed. The mechanical characteristics of the polymers under study have been examined.     

Modification of the lyotropic liquid crystalline microstructure of amphiphilic block copolymers in the presence of cosolvents

This article reviews the results of recent investigations on the macroscopic (phase behavior) and microscopic (microstructure) aspects of the role of cosolvents on the self-assembly of amphiphilic copolymers. A comprehensive account of the systematic studies performed in ternary isothermal systems consisting of a representative poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) block copolymer (Pluronic P105, EO₃₇PO₅₈EO₃₇), water and a polar cosolvent (such as glycerol, propylene glycol or ethanol) is presented. The effect of cosolvents on the copolymer phase behavior is quantified in terms of the highest cosolvent/water ratio able to maintain the liquid crystalline structures. The effect of cosolvents on the microstructure of the lyotropic liquid crystals is quantified in terms of the degree of relative swelling per cosolvent content per copolymer content, a parameter that characterizes the given cosolvent and copolymer. The set of correlations on the cosolvent effects on the phase behavior or microstructure to the cosolvent physicochemical characteristics (such as octanol/water partition coefficient or solubility parameter) have led to the development of a hypothesis that accounts for the cosolvent effects on the self-assembly of PEO–PPO–PEO block copolymers and can be used to predict them. The rich structural diversity and the potential for a precise and convenient modification of the lyotropic liquid crystalline microstructure of the PEO–PPO–PEO block copolymers is discussed in comparison to the phase behavior of the low-molecular nonionic surfactants.     

Pi‐conjugated chain extenders for the synthesis of optoelectronic segmented polyurethanes

The optical properties of mechanochromic materials change under mechanical stress. Segmented polyurethanes are elastomers composed of amorphous, saturated chain soft segments, and rigid pi‐conjugated hard domains. Within aggregates of hard domains pi–pi interactions may form and result in perturbation of the optoelectronic properties of the system. Disruption and restoration of these electronic interactions within the material may lead to observable mechanochromic response. A series of oligothiophene diols and diamines, as well as a naphthalene diimide diol, have been synthesized for incorporation into the hard domains of segmented polyurethanes and polyureas using long poly(tetramethylene oxide) chains as soft segments. The resulting polymers were evaluated to determine their extent of polymerization and their thermal stability. The optical properties of the materials were studied in solution and as thin films. Where possible the electrochemical properties of the polymers were also explored. The length of the soft segment chains in the segmented polyurethanes hindered electronic coupling of hard domains. Future work involving smaller, more solubilizing soft segments may allow for easier material characterization and mechanochromic response. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Conformational aspects of segmented poly(ester-urethanes)

Segmented poly(ester-urethanes) containing hard and soft segments, were obtained from aromatic diisocyanates with thiodiglycol or diethylene glycol as chain extenders, and poly(ethylene glycol)adipate usig a multistep polyaddition process. Transition temperatures by differential scanning calorimetry and thermo-optical analysis were employed to characterize polyurethane materials. Changes in the conformation of these polyurethanes were analyzed also, by viscometer measurements in N,N-dimethyl-formamide. The obtained data revealed that the thermal curves are influenced by the soft and hard segment structures in the temperature range studied.