Microstructures in Tl-1223/Ag tapes with different chemical compositions and Jc's

The microstructures of a Tl_0.8Pb_0.2Bi_0.2Sr_1.6Ba_0.4Ca₂Cu₃O_9+δ/Ag tape (tape I) with J_c of 17,600 A/cm² at 77 K and 0 T and three Tl_0.8Pb_0.2Bi_0.2Sr_1.8Ba_0.2Ca_2.2Cu₃O_9+δ/Ag tapes with J_c's of 9300 (tape II), 16,700 (tape III) and 25 200 A/cm² (tape IV) prepared using the powder-in-tube method and an in-situ reaction method, were investigated using high-resolution transmission electron microscopy. In the tape preparation, an intermediate rolling process was incorporated during final heat-treatment for the last tape, but not for the rest of the tapes. Tl-1223 grains are in a thin plate-like shape. Tendency of directional grain-alignment increased in an order of tapes I, II, II and IV. In tape IV, Tl-1223 grains are clearly textured at least partly. In lattice defects, while stacking faults were prevalent in the former composition, dislocations and holes were frequently observed in the latter. Also impurity phases were appeared to be more abundant in the former than in the latter. The relationship between J_c and the microstructure in the tapes was explained in a term of grain-linking.     

Fabrication, microstructure and critical current density of screen-printed Ag-(Bi, Pb)2Sr2Ca2Cu3Ox superconducting tapes

The influence of the sintering conditions on the microstructure and critical current density J_c has been studied on screen-printed Ag-(Bi, Pb)₂Sr₂Ca₂Cu₃O_x tapes with a ceramics mono-layer core. Three kinds of fabrication processes, which consist of a combination of cold working (rolling and/or pressing) and sintering, are applied. Four times repetition of pressing and sintering after the pre-sintering produces the highest c-axis alignment and achieves J_c= 1.5 × 10⁴ A/cm² (77 K, 0 T). The J_c versus θ data with an angle θ between B and the c-axis elucidate the relation between the anisotropy ratio γ=J_c(Bc)/J_c(B|c and the half-height angular width Δθ of a peak for Bc. This is related to both grain alignment and the J_c value. An increase in J_c, which comes from an improvement for grain alignment, enhances γ and narrows Δθ. The J_c versus θ data are fitted to the expression J_c(B, θ)=J _c(B, 90°)/[(γ−1)|cos θ|ⁿ+1] by regarding both γ and n as adjustable parameters. Fabrication of screen-printed tapes with multilayers (1≤N≤5) is presented, where the critical current increases from 8.0 A to 30.2 A at 77 K and 0 T as N increases.     

采用快速升温烧结方法生长Tl-1223超导薄膜的研究

报道了在铝酸镧(00l)衬底上生长Tl-1223超导薄膜的快速升温烧结方法以及铊(Tl)源陪烧靶的配比对Tl-1223薄膜晶体结构的影响.扫描电子显微镜观测表明,采用快速升温烧结方法生长的Tl-1223超导薄膜具有致密的晶体结构.X-射线衍射等测试表明,采用合适配比的陪烧靶在氩气环境下可以制备出纯c轴取向的Tl-1223超导薄膜,充氧退火后的薄膜具有较好的电学性能,其临界转变温度T_(c onset)达到116K,临界电流密度达到1.5MA/cm~2(77 K,0 T).实验结果表明,采用这一新的烧结方法制备Tl系超导薄膜具有升降温时间和恒温时间短、生产成本低等特点.     

Synthesis and properties of Hg0.7Pb0.3(BaSr)2Ca2Cu3Oz superconductors

We have synthesized Hg(Pb)-1223 with substitutions of Sr for Ba, i.e. Hg_0.7Pb_0.3Ba_2−xSr_xCa₂Cu₃O_z (x = 0.0–2.0) by the ampoule method. The spray-drying method and thermal decomposition under vacuum were applied for the preparation of homogeneous precursors. Samples with T_c = 110–128 K were obtained without oxygen annealing. We found that substitution of Ba by Sr remarkably relaxed the requirements on the precursors preparation and allowed their handling under ambient conditions.     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Normal-state transport properties of Ba1−xKxBiO3 crystals

The normal-state transport properties of Ba_1−xK_xBiO₃ crystals with a wide range of potassium compositions (0≤x≤0.62) were studied. Although the host material BaBiO₃ has a monoclinic structure, the system changes from a monoclinic to an orthorhombic structure with a small doping of potassium (0≤x<0.35) and behaves similar to a doped semiconductor, without exhibiting superconductivity. In the composition range, holes are majority carriers in the transport phenomena. When x exceeds a critical value (0.35), the system goes into a cubic superconducting phase with a single metallic band. The vicinity of the critical composition transport phenomena is easy to understand assuming the existence of two conducting channels that are made up of metallic and semiconducting phases. Maximum T_c exceeding 30 K was observed at x0.4, where carrier density was at its maximum. Overdoping with potassium suppresses superconductivity. In the metallic composition of x>0.45, transport seems to correlate with the phonon mode with an energy distribution of 15–43 meV.     

Granularity, microstructure, and flux creep in TlBa2Ca2Cu3O9+δ superconducting powder and silver-sheated tapes

Silver-sheathed TlBa₂Ca₂Cu₃O_9+δ (Tl-1223) tapes, with a transport critical current density, J_ct, of 6200 A/cm² at 75 K under zero magnetic field, were fabricated by the oxide-powder-in-tube (OPIT) method and characterized using an X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and superconducting quantum interference device (SQUID) magnetometer. The results of the magnetization and SEM study indicate that, in these tapes, individual grains are distributed randomly in orientation and weak links exist. However, strongly linked percolative current paths within the tape persisting in increasing fields, accompanied by strong intrinsic interplanar coupling, sustain a significant J_ct at high fields and lead to the plateau in the J_ct-H curve. Dislocation networks, which may act as effective pinning centers, are the common features observed in the tapes. To investigate the effects on flux pinning due to thermomechanical processing, magnetic relaxation at 1 and 2 T over 5–50 K was measured. The tape shows slightly lower normalized relaxation rates (S=-(1/M_o)dM/ dln t) than the cauliflower-like precursor powder. Analyses of the relaxation data obtained from the tape, after incorporating temperature dependence and field scaling, yield an expression for the effective pinning energy U_eff(J,T,H) = (U₁/H^0.54)[1-(T/ 72.5)²]⁴(J/J_i)^μ. This result was compared with the prediction of the collective flux-creep model, which suggests that Tl-1223 has a three-dimension-like (3D-like) vortex lattice. Presumably, a more plate-like powder morphology may result in improved texturing by the OPIT process. Tl_0.5Bi_0.5Sr₂CaCu₂O_7+δ ((Tl,Bi)-1212) powder with this morphology was therefore synthesized for comparison.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

Systematic thermopower measurements of the thallium cuprates Tl(Ba,Sr)2Cam−1CumO2m+3−δ and Tl2Ba2Cam−1CumO2m+4+δ

The thermoelectric power (TEP) S versus temperature has been systematically investigated for several series of the superconducting cuprates Tl(Ba,Sr)₂Ca_m−1Cu_mO_2m+3−δ (m = 2, 3) and Tl₂Ba₂Ca_m−1Cu_mO_2m+4+δ (m = 1, 2, 3). The consideration of the S(T_c) curves allows two important points to be found evidence for. The first one deals with the fact that all these superconducting thallium cuprates are systematically overdoped whatever T_c, and whatever the number of Cu or Tl layers; no underdoped superconducting cuprate could be obtained. The second point shows that there exist two classes of Tl cuprates: the weakly overdoped cuprates that exhibit a T_{c max} ≥ 100 K (all the triple copper layer cuprates and the 2212 cuprates) and those which can be heavily doped that exhibit a T_{c max} ≤ 90 K (the 2201 and the 1212 cuprates). The different behavior of thallium cuprates compared to YBa₂Cu₃O_7−δ and to bismuth cuprates is discussed.     

Mixed electronic and ionic conductivity of LaCo(M)O3 (M=Ga, Cr, Fe or Ni).: V. Oxygen permeability of Mg-doped La(Ga, Co)O3−δ perovskites

The LaGa_1−x−yCo_xMg_yO_3−δ solid solutions with rhombohedrally-distorted perovskite structure were ascertained to form in the concentration range of 0≤y≤0.10 at x=0.60 and 0≤y≤0.20 at x=0.35–0.40. Increasing cobalt content results in increasing electrical conductivity and thermal expansion of the perovskites. Thermal expansion coefficients of the LaGa_1−x−yCo_xMg_yO_3−δ ceramics were calculated from the dilatometric data to vary in the range of 12.4–19.8×10⁻⁶ K⁻¹ at 300–1100 K. Doping La(Ga,Co)O_3−δ solid solutions with magnesium leads to increasing oxygen nonstoichiometry, electronic and oxygen ionic conductivity. Oxygen permeation fluxes through LaGa_1−x−yCo_xMg_yO_3−δ membranes were found to be limited by the bulk ionic conduction and to increase with magnesium concentration, being essentially independent of cobalt content.     

The effect of gallium substitution on the superconductivity of the BiSrCaCuO system

Magnetic susceptibility, X-ray diffraction and resistivity measurements of the system Bi_1.4Pb_0.6Sr₂Ca_2−xGa_xCu₃O_y are reported for 0 x 2. The high-T_c 2223 phase with a T_c of 107 K for x = 0 exists for x 0.3. The low-T_c 2212 phase with a T_c of 75 K for x = 0 exists for the full range of x. The highest values of the critical temperature and the largest volume fraction of the low-T_c phase in compounds with Ga occur for x = 0.5 ± 0.1. The identification of CaO by X-ray diffraction for x 0.6 indicates that Ga replaces Ca in the compound.     

Intergranular properties of YBCO and BSCCO ceramic superconductors at low fields

Isothermal low-field AC susceptibility measurements have been used to analyze the intergranular critical current density J_c(T) on sintered, non-oriented YBa₂Cu₃O_7−δ and Bi₂Sr₂CaCu₂O_8+δ ceramic samples at zero field. Below the critical temperature, potential variations, J_c(T) ≈ (1−t_j)^m with t_j = T/T_j, have been found, T_j being the onset of grain's coherence, but with different exponents, supporting that different mechanisms limit the intergranular J_c values. Moreover, the effect of texture has been also considered on Bi₂Sr₂CaCu₂O_8+δ ceramics grown by the laser floating zone method, which have stronger intergranular junctions. Their high-temperature behaviour is limited by intrinsic effects, while at low temperatures the quality of the junctions is the limiting factor. The temperature dependence of the χ′(h₀) extrapolation at zero filed has also been correlated with the evolution of the intergranular penetration depth, λ_J(T).     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Double peak behavior of resistivity curves in Cd doped LaMnO3 perovskite systems

The effect of Cd doping on transport, magnetotransport, and magnetic properties has been investigated in the perovskite La_1−xCd_xMnO₃ (0x0.5) systems. The ρ(T) curves exhibit a sharp metal insulator transition (T_p1), which is close to paramagnetic to ferromagnetic transition (T_c) obtained from M−T curves for all samples. In addition, ρ(T) curves for Cd doped samples exhibit another broad transition (T_P2) below T_p1. This transition becomes more prominent and the transition temperature (T_p2) shifts to lower temperature with increasing Cd content. Such double peak behavior in the ρ(T) curve is attributed to the phase separation between the ferromagnetic metallic phases and the ferromagnetic insulating phases induced by the electronic inhomogeneity in the samples.     

Temperature-dependent magnetic moment in the MnAs-CrAs system

Magnetic susceptibilities have been measured for the mixed compounds Mn_1−xCr_xAs (0≤x≤1) and the compound MnP in the temperature region up to 1400 K. The _X¹_g vs. T curves of Mn_1−xCr_xAs follow the Curie-Weiss law only in the temperature region where the crystal structure is of the B8₁ type. Some important problems are pointed out from the data.     

Effect of Pr and Ca substitution on superconductivity in Y(1−x−yPrxCay)Ba2Cu3O7−δ

Pr substituted at constant Ca concentration for Y in (Y_1−x−yPr_xCa_y)Ba₂Cu₃O_7−δ superconductors have been prepared under identical conditions and the temperature dependence of the electrical resistivity of these samples are measured. The resistively determined values of T_c decrease linearly with increasing x (0 ≤ x ≤ 0.2) for constant y = 0.10 and 0.15 which provides convincing evidence that the suppression of superconductivity by Pr is mainly due to magnetic pair breaking. The suppression of superconductivity can also be correlated to the observed changes in oxygen content determined by iodometric analysis and to the average Cu-valences. However, it is found that the observed suppression of T_c cannot be compensated by appropriate hole doping with Ca.     

Superconductivity, Ca content and oxygen deficiency of Ga(Sr,Ca)2(Yb,Ca)Cu2O7

Superconducting transition temperature (T_c), Ca content and oxygen deficiency are studied on GaSr_1.8Ca_0.2Yb_1−xCa_xCu₂O₇ (x≤0.35). Superconducting samples with T_c=52 K are prepared after the annealing at 20 MPa of oxygen. The T_c is reduced through a slight oxygen loss accompanied by annealing in air above 650°C. The oxygen loss suggests the presence of short Cu–O chains in the GaO₄ slab. The formal valence of planar Cu required for the appearance of superconductivity depends on oxygen and Ca contents. The critical formal Cu valences are 2.105 and 2.125 for the samples annealed in air at 600°C and at 835°C, respectively. The values are higher than those of usual high-T_c superconductors. This can be explained by a high concentration of localized holes in the CuO₅ slab.     

Non-Fermi liquid regimes in U1−xMxPd2Al3(M=Y,Th)

The temperature-composition (T–x) phase diagram and NFL characteristics in the electrical resistivity ρ(T), specific heat C(T), and magnetic susceptibility χ(T) at low temperatures for the systems U_1−xM_xPd₂Al₃ (M=Y,Th) are described. The T–x phase diagram, the NFL characteristics, and the underlying mechanism for the NFL behavior are distinctly different for M=Y³⁺ and Th⁴⁺, apparently reflecting the difference in valence of the M atom substituents, and suggesting that U is tetravalent in these two systems.     

Effect of Hg addition on synthesis of Bi-based superconductors

We have investigated the effect of Hg addition on the superconducting properties of BiSrCaCuO system. Polycrystalline samples with nominal composition Bi₂Sr_2−xHg_xCa₁Cu₂O_y and Bi₂Sr_2−xHg_xCa₂Cu₃O_y (x=0.3) were synthesized and used to investigate the phase evolution by XRD, superconducting behaviour by R–T measurement and the structural grain boundary effects by SEM. From these measurements, it has been noticed that the phases obtained with both types of compositions are the same as Bi2212 but the T_c values are different. With additional annealing, T_{c zero} values were raised from 60 to 72 K in Bi₂Sr_2−xHg_xCa₁Cu₂O_y and 64 to 92 K in Bi₂Sr_2−xHg_xCa₂Cu₃O_y. Also, an improved grain boundary linkage has been observed by SEM for the 92 K sample.     

Magnetic moments and Fe hyperfine field interactions in Y(Fe1−xRux)2 ternaries

Measurements of magnetization and ⁵⁷Fe Mössbauer spectra have been made for Y(Fe_1−xRu_x)₂. The C15 type cubic structure is stabilized for xx 0.7. The C15 compounds is ferromagnetic with T_c200 K and its saturation moment decreases monotonically with increasing x, while the ⁵⁷Fe hyperfine field decreases only slightly with x. From these results, it is deduced that the Ru atoms have an induced moment of ≈1μ_B in the range x 0.2. In the C14 type phase, no magnetic ordering develops even at 4.2 K.