Crystallization of lithium metasilicate from lithium disilicate glass

The crystallization behavior of lithium disilicate glass powder heated in molten LiNO₃ salt was investigated using X-ray diffraction techniques. Heat treatment at 500°C with LiNO₃ molten salt caused a lithium metasilicate, Li₂SiO₃, crystal phase to appear after 5–96 h. By contrast, glass powder heat-treated in air at 500°C remained amorphous after 5 h and turned into lithium disilicate, Li₂Si₂O₅, crystal after 40 h. Qualitatively similar results were obtained at 400°C. Glass powder heat-treated at 575°C in both molten salt and in air turned into lithium disilicate crystal. Metasilicate crystallization occurs with LiNO₃ molten salt at 500 and 400°C due to the incorporation of lithium into the sample glass powder from the melt during crystallization. An increase in lithium content in the sample after molten salt heat treatment was confirmed by chemical analysis using dc plasma emission spectroscopy.     

The influence of the crystallization process on the internal friction of some oxide glasses

The influence of phase separation and crystallization on the internal friction of some oxide glasses is reviewed and discussed. In alkali-containing glasses, the internal friction peak caused by stress-induced diffusion of alkali ions decreases in magnitude and shifts to higher temperature slightly due to phase separation. And in alkali-free glasses phase separation only exerts a minor decrease upon the background of internal friction curves, whereas crystallization influences the internal friction of these glasses more strongly. Because of crystallization, in alkali-containing glasses alkali ions might diffuse in a residual glass phase and a crystal phase, respectively. This might cause corresponding internal friction peaks. And in alkali-free glasses, no evident internal friction peak is observed. However, the author found a high and wide internal friction peak at about 100°C in the crystallized MgO·Al₂O₃·SiO₂·TiO₂ and ZnO·Al₂O₃·SiO₂·ZrO₂ glasses. The peak occurring in the two glasses studied is probably connected with glass crystallization and crystallized crystals.     

Growth and morphology of ruby crystals with unusual chromium concentration

Single crystals of ruby have been obtained from fluxed melts based on the systems Li₂O–MoO₃, Li₂O–WO₃, Na₂O–WO₃, 2PbO–3V₂O₅, PbO–V₂O₅–WO₃, PbF₂–Bi₂O₃ and Na₃AlF₆ by both the TSSG method and spontaneous crystallization at the temperatures 1330–900 °C. Al₂O₃ solubility has been measured for the flux composition of 2Bi₂O₃–5PbF₂ in the temperature range 1200–1000 °C and dissolution enthalpy has been defined as 29.4 KJ/Mol. The composition of grown crystals was studied by electron microprobe analysis. The synthetic ruby contains from 0.51 to 6.38 at% of chromium admixture depending on the crystal growth conditions. Experimental results on growth conditions, composition and morphology of grown crystals are presented for each flux and temperature interval.     

Bridgman growth and properties of potassium lithium niobate single crystals

Transparent KLN crystals 10mm in diameter and 25 to 45mm in length have been grown by the modified vertical Bridgman technique from different melts in the range of 3035mol% K₂O, 1723mol% Li₂O and 4350mol% Nb₂O₅. The growth conditions are a growth rate of less than 0.25 mm/hr, temperature gradient in solid-liquid interface of 23 °C/mm and growth direction of <110>. As-grown KLN crystals have tetragonal tungsten bronze structure. Most of the as-grown crystals do not crack when cooling through the paraelectric/ferroelectric phase transition. 180° domain structures are observed after the KLN crystal was etched in boiling 2HNO₃:Hf. Dielectric properties and transmission spectrum of the as-grown KLN crystals are measured.     

Influence of ion exchange on liquid–liquid phase separation in alkali borosilicate glasses: effect of ion-exchange-induced metastable glass homogenization

Experimental results of studying the metastable liquid–liquid phase separation and homogenization induced by ion exchange in (15-x)Li₂O · xNa₂O · 35B₂O₃ · 50SiO₂ glass-forming system are presented. Both a homogeneous under-surface layer in a phase-separated glass and a phase-separated under-surface layer in a homogeneous glass have been formed by an ion exchange technique. The Li-for-Na ion exchange in the glass with x=15 led to phase-separated layers while the Na-for-Li ion exchange in the phase-separated glass with x=5 led to the homogeneous vitreous layers. These effects and the conditions that produce them are discussed from the viewpoint of phase equilibria in the system involved.     

Temperature fluctuations in a LiNbO3 melt during crystal growth

The synthesis of calcium carbonate (CaCO₃) crystals from aqueous solutions containing sodium dodecyl sulfate (SDS), poly(N-vinyl-1-pyrrolidone) (PVP), or SDS/PVP complexes has been performed through a slow titration method. It was found that aragonite and calcite co-existed in the prepared crystals. The formation of aragonite in the precipitation systems without magnesium ions indicates that at ambient temperature ca. 26.0°C, initially formed amorphous CaCO₃ could also transfer into aragonite in the sedimentary phase, which indicates the controlling factor of organic additives in the nucleation and growth process of CaCO₃ crystals. The appearance of hexagonal crystals in the suspensible phase confirmed the hexagonal crystallization cell of vaterite, and revealed the colloidal-dispersion function of the SDS/PVP complex in the crystallization process of CaCO₃.     

Crystallization habit of calcium carbonate in presence of sodium dodecyl sulfate and/or polypyrrolidone

The synthesis of calcium carbonate (CaCO₃) crystals from aqueous solutions containing sodium dodecyl sulfate (SDS), poly(N-vinyl-1-pyrrolidone) (PVP) or SDS/PVP complexes has been performed through a slow titration method. It was found that aragonite and calcite coexisted in the prepared crystals. The formation of aragonite in the precipitation systems without magnesium ions indicates that at ambient temperature ca. 26.0°C, initially formed amorphous CaCO₃ could also transfer into aragonite in the sedimentary phase, which indicates the controlling factor of organic additives in the nucleation and growth process of CaCO₃ crystals. The appearance of hexagonal crystals in the suspensible phase confirmed the hexagonal crystallization cell of vaterite, and revealed the colloidal-dispersion function of the SDS/PVP complex in the crystallization process of CaCO₃.     

Colloidal sol/gel processing of ultra-low expansion TiO2/SiO2 glasses

A series of titania-silica glasses with 0–9% TiO₂ were fabricated using a sol/gel process. The sol was prepared by dispersing colloidal silica fume in an aqueous solution of titania which was synthesized through the acid-catalyzed hydrolysis of titanium isopropoxide. The sols gelled in 2–4 days, and then were dried for 6–8 days. The dry gels were sintered at 1450–1500°C to produce clear, dense, microstructure-free glasses. The gels underwent a total shrinkage of 50% to yield glass rods about 50 mm long and 5 mm in diameter, or glass discs about 4 cm in diameter and 5 mm thick. The drying step was most critical in the production of crack-free specimens.

In the gel, the transmission electron microscope (TEM) revealed the presence of 1–5 nm rutile microcrystallites uniformly distributed within a network of colloidal silica particles. After sintering to 1450–1500°C, though, a dense, transparent, microstructure-free glass was created. Fourier transform infrared spectroscopy (FTIR) verified the formation of an amorphous solid-solution of titania and silica after sintering.

The thermal expansion of the glasses was measured using a differential dilatometer. The average linear coefficients of thermal expansion (CTE @ 25–675°C) varied between +5 × 10⁻⁷ and −0.2 × 10⁻⁷°C⁻¹ in the range 0 to 9% TiO₂. The glass with 7.2% TiO₂ exhibited a zero thermal expansion coefficient at 150–210°C. The hysteresis in CTE on heating and cooling was of the order of 0.01–0.02 ppm.     

Microanalytical study of Er-doped LiNbO3 crystals obtained by Er–Li ion exchange

Erbium-doped lithium niobate (LiNbO₃) crystals were produced by Er–Li ion exchange (IE) process. The role of the process parameters such as exchange time and temperature, crystal cut direction, composition and heating rate of the Er ions liquid source was investigated by means of secondary ion mass spectrometry, X-ray diffraction (XRD) and microluminescence techniques. We demonstrated that Er effective diffusion coefficient is two orders of magnitude greater with respect to the thermal diffusion from Er film. We observed that no Li deficient phase can be achieved and that active Er ions are homogeneously incorporated in the substrate. The method is suitable for Er doping of LiNbO₃ crystals at relative low temperature (from 570°C to 650°C).     

Sodium borosilicate glasses prepared by the sol-gel process

A sodium borosilicate gel of composition 80SiO₂·15B₂O₃·5Na₂O (wt%) was prepared from tetraethyl orthosilicate, trimethyl borate, sodium methylate, H₂O, and HCl as the catalyst. Variation of specific surface area and porosity as a function of heating temperature indicated that closed pores were opened at temperatures lower than 400°C and collapsed above 450°C. From TG and DTA curves, about 19% Si and B atoms are evaluated to have −OH bonds. X-ray diffraction patterns indicated crystallization of low-cristobalite out of the gel when it was heated at 700°C for 5 h, showing a difference from a melt-quenched glass of the same composition.     

Precipitation of In2O3 nano-crystallites from glasses in the system Na2O/B2O3/Al2O3/In2O3

Glasses in the system Na₂O/B₂O₃/Al₂O₃/In₂O₃ were melted and subsequently tempered in the range from 500 to 700 °C. Depending on the chemical composition, various crystalline phases were observed. From samples without Al₂O₃, In₂O₃ could not be crystallized from homogeneous glasses, because either spontaneous In₂O₃ crystallization occurred during cooling, or other phases such as NaInO₂ were formed during tempering. The addition of alumina, however, controlled the crystallization of In₂O₃. Depending on the crystallization temperature applied, the crystallite sizes were in the range from 13 to 53 nm. The glass matrix can be dissolved by soaking the powdered glass in water. This procedure can be used to prepare nano-crystalline In₂O₃-powders.     

Annealing effects of highly homogeneous a-Si1−xCx:H

We report the effect of annealing on the properties of amorphous hydrogenated silicon carbide thin films. The samples were deposited onto different substrates by plasma enhanced chemical vapor deposition at temperatures between 300 and 350 °C. The gaseous mixture was formed by silane and methane, at the ‘silane starving plasma regime’, and diluted with hydrogen. Rutherford backscattering and Fourier transform infrared spectrometry were used, respectively, to determine the atomic composition and chemical bonds of the samples. The film’s structure was analyzed by means of X-ray absorption fine structure and X-ray diffraction. For temperatures higher than 600 °C, amorphous silicon carbide films annealed under inert atmosphere (Ar or N₂) clearly changed their structural and compositional properties due to carbon loss and oxidation, caused by the presence of some oxygen in the annealing system. At 1000 °C, crystallization of the films becomes evident but only stoichiometric films deposited on single crystalline Si[1 0 0] substrates presented epitaxial formation of SiC crystals, showing that the crystallization process is substrate dependent. Films annealed in high-vacuum also changed their structural properties for annealing temperatures higher than 600 °C, but no traces of oxidation were observed or variations in their silicon or carbon content. At 1200 °C the stoichiometric films are fully polycrystalline, showing the existence of only a SiC phase. The XANES signal of samples deposited onto different substrates and annealed under high-vacuum also show that crystallization is highly substrate dependent.     

Ni-containing spinel aluminates glass-ceramic materials obtained from cordieritic bulk glasses

Monolithic glasses with compositions 2MO · 2Al₂O₃ · 5SiO₂, being M=Ni and equimolar mixtures of Ni and Mg, were prepared at 1650 °C by melting mixtures of raw materials. The crystallization of monoliths was produced by heat-treatment at several temperatures up to 1200 °C. The crystallization sequence was followed by differential thermal analysis (DTA), X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) and diffuse reflectance spectroscopies. Surprisingly, the only crystalline phase formed after heating up to 1100 °C was a nickel-containing aluminate spinel for both compositions. The microstructural characterization indicated the volume crystallization of well formed octahedral crystals of spinel with smaller size than 500 nm. Finally, it has been proved that nickel-containing aluminosilicate glasses could be converted into μ- or -cordierite- and spinel-based glass-ceramics by thermal treatment of powdered glasses and monolithic bodies, respectively.     

Correlation between interfacial structure and c-axis-orientation of LiNbO3 films grown on Si and SiO2 by electron cyclotron resonance plasma sputtering

Thin films of crystalline lithium niobate (LN) grown on Si(1 0 0) and SiO₂ substrates by electron cyclotron resonance plasma sputtering exhibit distinct interfacial structures that strongly affect the orientation of respective films. Growth at 460–600 °C on the Si(1 0 0) surface produced columnar domains of LiNbO₃ with well-oriented c-axes, i.e., normal to the surface. When the SiO₂ substrate was similarly exposed to plasma at temperatures above 500 °C, however, increased diffusion of Li and Nb atoms into the SiO₂ film was seen and this led to an LN–SiO₂ alloy interface in which crystal-axis orientations were randomized. This problem was solved by solid-phase crystallization of the deposited film of amorphous LN; the degree of c-axis orientation was then immune to the choice of substrate material.     

Synthesis of fluorine doped silica gel and its properties at high temperature

Fluorine doped silica gels were synthesized by using the sol-gel processes of (A) SiF₄(g) and H₂O(1) and (B) the mixed solution of Si(OC₂H₅)₄, C₂H₅OH, H₂O and H₂SiF₆. By the former process we obtained a gel of relatively high fluorine content (8–12 at.%F), while we could synthesize the gel of 0–12 at.% F by adjusting the F/Si ratio of the starting solution mixtures by the latter process.

The defluorination behavior and the structural change of these gels at high temperature were studied by heating-mass spectrometry, IR and ESR measurements. The results revealed the following: (1) defluorination by liberation of SiF₄(g) was admitted from temperatures at about 400°C and was controlled by the diffusion of fluorine in the gel bulk. (2) The peak separation analysis for the IR band of 1300-900 cm⁻¹, where the stretching vibrations of Si---O and Si---F appear, showed that the change of the band shape resulted from the increase or the decrease of the Si---F bonds and the change of the bond angle of Si---O---Si as well as the change of the force constant accompanied by fluorination or defluorination. (3) The defects of the Si E′ center were induced by X-ray irradiation depending on the degree of the defluorination, and were reduced by the heat treatment. However, with the heat treatment at temperatures higher than 1000°C, the E′ center increased again. The IR spectra suggest that this behavior might correspond to the gel-glass trasition.     

Al2O3-TiO2 and Al2TiO5 ceramic materials by the sol-gel process

Ceramic materials with a very low thermal expansion coefficient are synthesized by the sol-gel process. The binary gel is obtained by hydrolysis and polycondensation reactions of organometallic compounds of aluminium and titanium. The thermal evolution of the amorphous powder is followed by DTA and TGA measurements. Structural evolution is followed using X-ray diffraction. The crystallization of the TiO₂ rutile and Al₂O₃ corindon starts at 700 and 900°C respectively. The transformation of Al₂O₃ and TiO₂ into Al₂TiO₅ appears between 1200 and 1300°C. The densification of the powder is performed by the hot pressing process. The shrinkage of the powder was previously followed by dilatometric measurements. The physical properties of the final material are studied as a function of pressing parameters.     

Colour of silicate sol-gel glasses containing CuO

Glasses with compositions xCuO·(100 − x)SiO₂ and 5R_nO·xCuO. (95−x)SiO₂, where R = Li, Na, Ca and X = 0.25–10, were prepared by the sol-gel method. Samples were thermally treated between 60 °C and 1000 °C in oxidizing and reducing atmospheres. Copper incorporation was studied by spectrophotometry, X-ray diffraction and TEM.

All the samples are transparent and present a bluegreen colour at 600 °C in oxidizing atmosphere. The obtained results prove that copper is mainly incorporated as Cu²⁺.

At higher temperatures all the samples present -cristobalite, the samples containing Li₂O or CaO also show -quartz as crystalline phases.

In reducing atmosphere particle segregation takes place, producing in some cases opaque materials. Under specific conditions, transparent ruby glasses were obtained.     

Structural transformation of the TiO2---SiO2 system gel during heat-treatment

The gel formation of the (100-x)TiO₂·xSiO₂ (x = 0–10 mol%) system has been studied. The progressive elimination of residues was followed by DTA and TGA curves. DTA curves showed that the formation of anatase during heat treatment could be sensibly slowed down with the increase of SiO₂. The relationship between the gel composition and crystallization temperature of anatase has been systematically investigated. The X-ray diffraction spectra demonstrated that the crystallization temperature of anatase is 400°C for TiO₂ gel and 430°C for 90TiO₂ - 10SiO₂ gel. The infrared absorption spectra were used to follow the structural transformation of gels heat-treated at different temperatures. With the help of EPR it is evident that titanium ions exist only in tetravalence.     

The crystallisation of the yttrium–sialon glass: Y15.2Si14.7Al8.7O54.1N7.4

The development of microstructure during crystallisation of a glass with composition Y_15.2Si_14.7Al_8.7O_54.1N_7.4 has been studied by analytical and high resolution transmission electron microscopy. Crystal nucleation at temperatures in the range 965–1050°C occurs by the heterogeneous nucleation of lenticular-shaped yttrium, silicon and aluminium containing crystals on silicon-rich clusters that formed during glass preparation. The lenticular crystals have a wide range of composition after heat treatment at 1050°C; the yttrium cation percentage varies around that of the expected B-phase composition Y₂SiAlO₅N but the aluminium content is lower and the silicon content generally significantly higher than that. The crystals display the hexagonal crystal structure of B-phase, although the results from EDX analysis imply that the atomic arrangement of the lattice is not the previously proposed B-phase structure. Crystal growth during prolonged heat treatment at 1050°C occurs to a significant extent by coalescence.     

Preparation and physical properties of amorphous V2O5 containing TiO2, Na2O or Li2O

V₂O₅ gels containing up to 18 mol% of TiO₂ were obtained through the simultaneous hydrolysis of alkoxides in ethanol solution. V₂O₅ gels containing Na₂O or Li₂O were obtained through the ion exchange method. The crystallization temperature, T_cr, of the gels increased and the H₂O content of the gels decreased by the addition of TiO₂ or Na₂O. These additives seem to stabilize the amorphous state of the gels. On the other hand, T_cr and the H₂O-content slightly varied with the addition of Li₂O. No ionic polarization was observed in coating films of the gels dried at temperatures below T_cr. The dc conductivity of the films was anisotropic, and increased with the addition of Li₂O or Na₂O. However, it decreased with increasing TiO₂ content. The fiber-like structure of gels was observed by TEM. The gels obtained from alkoxides were thin and short in comparison with the gels obtained through the ion exchange method.