基于阻抗匹配条件的树枝状超材料吸收器

基于树枝状金属结构单元的电磁谐振特性,设计了一种双面大小树枝状结构的超材料吸收器,该结构分别是正面二级树枝及正对的背面三级树枝.通过仿真模拟设计了不同的阻抗匹配方式,调节相应的结构参数,找到了阻抗匹配对吸收特性的影响.在最佳的阻抗匹配条件下,得到最大吸收率.实验测量表明,阻抗匹配条件下双面大小树枝模型可以实现90.01%吸收率.增加样品层数可以有效的增加吸收率,3层样品就可以达到99%以上的吸收率,实现工程意义的完美吸收.     

一种基于十字镂空结构的低频超材料吸波体的设计与制备

设计了一种十字镂空的超材料结构,与传统的铁磁吸波材料相结合,实现了低频吸收频带的扩宽.仿真结果显示,吸波体在2-4 GHz范围可以实现-10 dB以下的吸收,相比于没有加载超材料的情况,吸收带宽扩展了0.5 GHz.实验结果在2.5-5.1 GHz范围内也显示了相似的吸收曲线,低于-9 dB的吸收频带有0.48 GHz的扩宽,扩展了23%.不同结构的能量损耗密度分布表明,相比于无镂空的十字结构,镂空十字结构可以增加磁场能量损耗,加强单元结构之间的耦合,降低超材料对传统吸波材料性能的破坏.探索了传统铁磁吸波材料厚度的变化对吸波体吸收性能的影响,发现由超材料引入的附加峰位置不随着吸波材料厚度的改变而明显地移动.根据这个结果,进一步设计了由两种超材料叠加组合而成的吸波体,仿真结果和实验结果均显示,在降低了1.1 mm铁磁吸波材料层厚度的情况下,使低频吸收带宽又扩展了0.9 GHz.     

基于超材料的堆叠式宽谱热辐射吸收器的设计北大核心CSCD

针对目前吸收器存在的吸收光谱过窄的技术问题,提出了一种由金属与非金属组成的具有金属-绝缘体-金属(MIM)结构的超材料吸收器模型,并模拟分析其辐射特性,计算总体吸收性能。针对给定的波长范围,通过对超材料吸收器的结构参数的改变,对比分析了周期、宽度、金属层厚度和介电层厚度对吸收器辐射特性的影响。结果表明,介电层厚度对吸收率的影响最为明显。研究了不同结构参数微结构的堆叠对多层超材料吸收器吸收峰的影响,结果显示可以通过叠加获得更高的吸收峰值,提升吸收器的总体吸收效率,在可见光到红外光间形成一个宽谱吸收。     

基于超材料的可调谐的太赫兹波宽频吸收器

随着频谱资源的日益稀缺,太赫兹波技术在近十几年的时间里得到了越来越多的关注,并取得了巨大的进展.由于高吸收、超薄厚度、频率选择性和设计灵活性等优势,超材料吸收器在太赫兹波段备受关注.本文设计了一种"T"型结构的超材料太赫兹吸收器,同时获得了太赫兹多频吸收器和太赫兹波宽频可调谐吸收器.它们结构参数一致,唯一的区别是在太赫兹波宽频可调谐吸收器的顶端超材料层上添加了一块方形光敏硅.这种吸收器都是三层结构,均由金属基板、匹配电介质层以及顶端超材料层组成.仿真结果表明,太赫兹波多频吸收器拥有6个吸收率超过90%的吸收峰,其平均吸收率高达96.34%.而太赫兹波宽频可调谐吸收器通过改变硅电导率,可以控制吸收频带的存在与否,同时可以调整吸收峰的频率位置,使吸收峰频率在一个频带宽度大约为30 GHz的范围内调整.当硅的电导率为1600 S/m时,吸收率超过90%的频带宽度达到240 GHz,而且其峰值吸收率达到99.998%.     

一种宽频带超材料吸波体的设计及其特性

为了获得吸收率高、吸波带宽宽的超材料,设计了一种谐振超材料吸波体.该吸波体由多个开口圆环组成,采用商业软件CST Studio Suite 2009频域求解器计算了其在25~35 GHz波段内的S参量,并计算了其吸波率A(ω),在28.4 GHz处吸收率达到86%,带宽达到3.5 GHz.利用不同吸波频段的叠加效应,设计了一种谐振超材料吸波组合体,计算了在25~35 GHz波段的S参量,在29.7 GHz处吸波率达99.9%,吸波带宽达到3.1 GHz,吸收率明显增加.将GHz波段的结构缩小1 000倍,在THz波段同样可以达到高吸收,说明超材料吸波体可以通过对结构尺寸调节改变吸收波段.同时,对其阵列进行仿真计算,发现不同的排列方式仿真结果不同.由于各个谐振环之间的相互作用对吸收效果影响较大,吸收率减小.该吸波材料由金属组成,能灵活地对介电常量和磁导率进行调节,从而实现高吸收.     

树叶状红外频段完美吸收器的仿真设计

设计了一种由树叶状金属薄膜-介质层-金属薄膜构成的低剖面完美吸收器模型. 通过对金属介电性能采用Drude定理,仿真发现调节结构参数可在红外通讯频段几乎达到完美吸收 (吸收率为99.5%),并且在某些特定的结构参数下可以同时实现双频段的完美吸收 (其吸收率分别达到99.67%和97.13%),这在某种意义上展宽了吸收频带, 对红外吸收器的设计与应用极为有利.最后探索了叶颈宽度变化对双频吸收峰位置的影响, 以便对双峰吸收进行调频操作.这种红外频段的超材料吸收器具有结构简单、吸收效率极高、工作频段宽等优点.     

一种宽频带超材料吸波体的设计及其特性

为了获得吸收率高、吸波带宽宽的超材料,设计了一种谐振超材料吸波体.该吸波体由多个开口圆环组成,采用商业软件CST Studio Suite 2009频域求解器计算了其在25～35 GHz波段内的S参量,并计算了其吸波率A(ω),在28.4 GHz处吸收率达到86％,带宽达到3.5 GHz.利用不同吸波频段的叠加效应,设计了一种谐振超材料吸波组合体,计算了在25～35 GHz波段的S参量,在29.7 GHz处吸波率达99.9％,吸波带宽达到3.1 GHz,吸收率明显增加.将GHz波段的结构缩小1 000倍,在THz波段同样可以达到高吸收,说明超材料吸波体可以通过对结构尺寸调节改变吸收波段.同时,对其阵列进行仿真计算,发现不同的排列方式仿真结果不同.由于各个谐振环之间的相互作用对吸收效果影响较大,吸收率减小.该吸波材料由金属组成,能灵活地对介电常量和磁导率进行调节,从而实现高吸收.     

基于超材料的微波双波段吸收器

基于闭合双环单元结构, 设计、仿真、测试了对偏振无依赖性的双波段超材料吸收器. 实验结果表明, 该设计在频率4.06 GHz和6.66 GHz存在两个显著吸收峰, 吸收率分别为99.60%和95.83%, 并且在入射角达到50°时, 吸收率仍然保持在83%以上. 由于单元结构具有旋转对称性, 使得该吸收器对偏振不敏感, 能同时实现横电波和横磁波的双波段吸收. 吸收频率决定于闭合环大小, 调节闭合环尺寸能够灵活实现特定频率的吸收. 这些优点使我们的设计在多频谱成像、热辐射探测等应用中表现出较大的潜力.     

超薄柔性透射型超构材料吸收器

设计并加工了一种超薄柔性透射型吸收器,总体厚度为0.288 mm,可实现柔性弯曲,容易做到与曲面目标共形.该吸收器由三层结构组成,底层是金属光栅,中间为介质层,表面单元由两条平行放置的尺寸不同的金属线组成.仿真和实验结果表明,对横电波在5和7 GHz的吸收分别达到97.5%和96.0%,对横磁波在3.0—6.5 GHz都能保持90%以上的透射率.两个吸收频点可分别独立调节,增加了设计的灵活性.另外,当入射角增大到60°时,该吸收器的性能基本不受影响,表现出良好的广角特性.     

基于圆台结构的超宽带极化不敏感太赫兹吸收器

本文提出一种基于圆台形吸收单元的超宽带、极化不敏感的超材料太赫兹吸收器. 该超材料吸收器采用金属薄膜金和介质层二氧化硅交替叠加的多层结构. 采用商业软件CST Studio Suite 2009时域求解器计算了其在0–10 THz波段内的吸收率A（ω）,在2–10 THz之间实现了对入射太赫兹波的超宽频带强吸收. 仿真结果表明,由于其圆台形单元结构,在器件垂直方向上形成一系列不同尺寸的微型吸收器,产生了吸收频点相连的多频吸收峰. 利用不同吸收峰的耦合叠加效应,获得超过8 THz的超宽带太赫兹波吸收,吸收强度达到92.3%以上. 这一结构具有超宽带强吸收,360°极化不敏感以及易于加工等优越特性,因而在太赫兹波探测器、光谱成像以及隐身技术方面具有潜在的应用. 关键词： 太赫兹波 超材料吸收器 圆台结构 超宽带     

Tunable broadband metamaterial absorber consisting of ferrite slabs and a copper wire

A tunable broadband metamaterial absorber is demonstrated at microwave frequencies in this paper.The metamaterial absorber is composed of ferrite slabs with large resonance beamwidths and a copper wire.The theoretical analysis for the effective media parameters is presented to show the mechanism for achieving the perfect absorptivity characteristic.The numerical results of transmission,reflectance,and absorptivity indicate that the metamaterial absorber exhibits a near perfect impedance-match to free space and a high absorptivity of 98.2% for one layer and 99.97% for two layers at 9.9 GHz.The bandwidth with the absorptivity above 90% is about 2.3 GHz.Moreover,the absorption band can be shifted linearly in a wide frequency range by adjusting the magnetic bias.This metamaterial absorber opens a way to prepare perfectly matched layers for engineering applications.     

Numerical study of metamaterial absorber and extending absorbance bandwidth based on multi-square patches

A simple design of metamaterial absorber (MA) was proposed based on a periodic array of metal patch at microwave frequencies. Our design could exhibit absorption of 99.9% confirmed by numerical simulation. Such high narrowband absorption which mainly based on strong electric and magnetic resonances overlapping in a certain frequency range and perfect impedance-matched (z = 1) to the free space. Numerical simulations demonstrate that the MA could achieve very high absorptivity at wide angles of incidence for both transverse electric (TE) wave and transverse magnetic (TM) wave. The absorption band of our device is effectively extended by patterning multi-square patches of different dimension elements with appropriate geometrical parameters in a co-planar. Finally, the composite MA is only 0.4 mm thick, with a maximum absorption of 99.8% at 15.8 GHz, and a full width at half maximum (FWHM) bandwidth of 2 GHz by numerical simulation, which may have potential applications in the detection of explosives and stealth.     

宽带透射吸收极化无关超材料吸波体

提出了一种新的基于磁性吸波体材料的具有低频透射和高频宽带吸收特性的超材料吸波体.该超材料吸波体在1 GHz的透射系数为-0.5 dB,具有较好的低频透射特性,可以实现对低频信号的相互通信;在频率大于8.4 GHz的频段,吸收率均大于80%,基本覆盖整个X波段和Ku波段,实现高频宽带吸收.此外,由于该超材料吸波体的单元金属周期结构具有较好的四重旋转对称性,因而是极化无关的.该透射吸收超材料吸波体设计简单,实用性强,具有较强的潜在应用价值.     

Broadband,polarization-insensitive,and wide-angle microwave absorber based on resistive film

A simple design of broadband metamaterial absorber(MA) based on resistive film is numerically presented in this paper.The unit cell of this absorber is composed of crossed rectangular rings-shaped resistive film,dielectric substrate,and continuous metal film.The simulated results indicate that the absorber obtains a 12.82-GHz-wide absorption from about 4.75 GHz to 17.57 GHz with absorptivity over 90% at normal incidence.Distribution of surface power loss density is illustrated to understand the intrinsic absorption mechanism of the structure.The proposed structure can work at wide polarization angles and wide angles of incidence for both transverse electric(TE) and transverse magnetic(TM) waves.Finally,the multi-reflection interference theory is involved to analyze and explain the broadband absorption mechanism at both normal and oblique incidence.Moreover,the polarization-insensitive feature is also investigated by using the interference model.It is seen that the simulated and calculated absorption rates agree fairly well with each other for the absorber.     

Multi-band microwave metamaterial absorber based on coplanar Jerusalem crosses

The influence of the gap on the absorption performance of the conventional split ring resonator(SRR) absorber is investigated at microwave frequencies. Our simulated results reveal that the geometry of the square SRR can be equivalent to a Jerusalem cross(JC) resonator and its corresponding metamaterial absorber(MA) is changed to a JC absorber. The JC MA exhibits an experimental absorption peak of 99.1% at 8.72 GHz, which shows an excellent agreement with our simulated results. By simply assembling several JCs with slightly different geometric parameters next to each other into a unit cell, a perfect multi-band absorption can be effectively obtained. The experimental results show that the MA has four distinct and strong absorption peaks at 8.32 GHz, 9.8 GHz, 11.52 GHz and 13.24 GHz. Finally, the multi-reflection interference theory is introduced to interpret the absorption mechanism.     

一种基于3D打印技术的结构型宽频吸波超材料

设计了一种三层宽频吸波超材料,其表层和中间层为单元尺寸不同的周期阵列结构,底层为吸波平板结构,优化后的总厚度仅为4.7 mm,并采用三维(3D)打印技术成功制备了该吸波超材料.吸波体反射率测试结果表明,在电磁波垂直入射条件下,宽频吸收峰分别出现在5.3和14.1 GHz,两峰叠加使得其在4-18 GHz频率范围内反射损耗均小于-10 dB.采用S参数反演法计算了每一层的等效电磁参数,并利用多层结构反射率公式推导得出该模型的理论反射率,理论计算结果与实测结果基本一致.通过研究能量损耗、电场分布和磁场分布揭示了吸波机理,分析表明该吸波体的宽频吸收效果源于三层结构产生的吸收带宽叠加.本文提出的吸波超材料具有良好的宽频吸收效果,尤其在低频范围吸波性能较佳,结合3D打印快速成型技术,可获得结构精细的三层吸波超材料,具有重要的实际应用价值和广阔的应用前景.     

The modification of the initial susceptibility of dilute binary ferrofluids based on γ-Fe2O3/ZnFe2O4 nanoparticles

This paper presents a multi-band metamaterial absorber comprising three multi-gap split-ring resonators (SRRs) with different radii and ring widths, designed in combinatorial approach. Experiments demonstrate that it can perform absorption peaks at three resonant frequencies 7.10 GHz, 10.04 GHz, and 17.44 GHz with the absorption of 99.90%, 99.91%, and 99.68%, respectively. The physical mechanism of metamaterial absorber was explained through numerical calculation and simulation, which showed that three absorption peaks were caused respectively by the three four-gap SRRs. The absorber is insensitive to incident angles and polarization states, so it has broad prospect of application.