一种高效染料敏化太阳电池电解质添加剂

报道了一种新型染料敏化太阳电池电解质添加剂——N-十六烷基吡啶碘(N-CPI).往电解质中添加0.02MN-CPI,能同时提高染料敏化太阳电池(DSSC)的短路电流和开路电压,光电转换效率也由4.429%提高到6.535%,增幅高达47.55%,由此可见,N-CPI是一种高效电解质添加剂.N-CPI这种功能来源于其双极性基团的特殊分子结构,这种结构使N-CPI在电解质中如表面活性剂那样形成有序分布,影响I-/I3-的扩散和氧化还原性能,进而影响DSSC的光电性能.     

Influence of amylopectin in dimethylsulfoxide on the improved performance of dye-sensitized solar cells

A highly viscous liquid electrolyte is prepared by adding a small amount of amylopectin into dimethylsulfoxide solvent. By using this viscous electrolyte, a dye-sensitized solar cell (DSSC) enhances the short-circuit photocurrent density and solar-to-electricity conversion efficiency by 22% and 8.4%, respectively, compared to those obtained with the reference cell without amylopectin. Furthermore, the stability of the DSSC is enormously improved by the addition of amylopectin. Polarization curves indicate that amylopectin is a reasonable corrosion inhibitor for silver metal in the electrolyte containing I₃^?/I^? couple.     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

Effect of organic dye on the performance of dye-sensitized solar cell utilizing TiO2 nanostructure films synthesized via CTAB-assisted liquid phase deposition technique

This work is concerned with the growth of TiO₂ nanostructures as photovoltaic materials of dyesensitized solar cell (DSSC) via phase liquid deposition technique treated with CTAB surfactant. This work investigates the influence of organic dyes, N719, N3 and Z907 as photosensitizer on the photovoltaic parameters of TiO₂ nanostructures dye-sensitized solar cells (DSSCs). It also highlights the effect of the concentration of the best dye, N719 on the performance of the cell. The platinum films as counter electrode of the DSSC were prepared by sputtering platinum pellet on ITO substrate. The redox couple of the electrolyte utilized in the DSSC was iodide/triiodide. The cell sensitized with N719 dye demonstrated the best performance compared with the cell sensitized with another two dyes, N3 and Z907. This is due to N719 dye possess the highest optical absorption in visible region. The cell sensitized with 0.8 mM N719 dye performs the highest short-circuit current density, J _sc and power conversion efficiency, η since it posses the highest absorption in visible region. The DSSC utilizing 0.8 mM N719 dye demonstrated the highest J _sc and η of 6.48 mA cm^?2 and 1.69%, respectively.     

Rubbery copolymer electrolytes containing polymerized ionic liquid for dye-sensitized solar cells

A novel type of random copolymer comprised of a polymerized ionic liquid, poly(1-((4-ethenylphenyl)methyl)-3-butyl-imidazolium iodide) (PEBII), and amorphous rubbery poly(oxyethylene methacrylate) (POEM) was synthesized and employed as a solid electrolyte in an I₂-free dye-sensitized solar cell (DSSC). The copolymer electrolytes deeply infiltrated into the nanopores of mesoporous TiO2 films, resulting in improved interfacial contact of electrode/electrolyte. The glass transition temperature (T _g) of the PEBII–POEM (?23 °C) was lower than that of PEBII homopolymer (?4 °C), indicating greater chain flexibility in the former. However, the DSSC efficiency of PEBII–POEM (4.5 % at 100 mW/cm²) was lower than that of PEBII (5.9 %), indicating that ion concentration is more important than chain flexibility. Interestingly, upon the introduction of ionic liquid, i.e., 1-methyl-3 propylimidazolium iodide, the efficiency of PEBII remained almost constant (5.8 %), whereas that of PEBII–POEM was significantly improved up to 7.0 % due to increased I^? ion concentration, which is one of the highest values for I₂-free DSSCs.     

Effects of water-based gel electrolyte on the charge recombination and performance of dye-sensitized solar cells

A new water-based solution of ion-conductive polymeric gel electrolyte composed of polyethylene glycol and polyvinylpyrrolidone as gel-forming substances, I^?/I₃ ^? as reversible redox couple, and various ratios of acetonitrile/water solvents was prepared and used in the fabrication of dye-sensitized solar cells. The effects of water on the electrochemical behavior of the prepared electrolyte solutions were examined by the cyclic voltammetry and electrochemical impedance spectroscopy techniques. Electrochemical impedance spectroscopy was employed to quantify the charge-transfer resistance and the electron lifetime at the TiO₂ conduction band. The characteristic peak shifted to a lower frequency in the Bode phase plot, which is an indication of a longer electron lifetime for the cell containing more water content. Photovoltaic performance of the cells prepared by the new water-based gel electrolyte was studied. Changes in the current density–voltage (J–V) characteristics can be explained based on the effect of water on the energetics and kinetics of charge transport and charge recombination in the dye-sensitized solar cells (DSSCs). It was observed that the increase in open-circuit voltage (V _oc) and fill factor and decrease in J _SC were noticeable for cells containing water-based gel electrolyte. It was indicated that the charge recombination between injected electrons and electron acceptors (polyiodide) in the redox electrolyte was remarkably inhibited by the increase of water. The photovoltaic performance stability of the DSSC containing gel electrolyte solution including 50 wt% of water was examined, and it was shown that it is more stable than conventional cells considerably for 168 h. Energy conversion efficiency of 2.30 % was achieved, under illumination with a simulated solar light of 100 mW cm^?2.     

Efficiency enhancement with chloride to iodide ion exchange of benzimidazolium salt as a redox mediator

The new benzimidazolium derivative (SM-1) salt with ion exchange from the (SM-0) was fabricated and characterized by proton-nuclear magnetic resonance (¹H-NMR), carbon-nuclear magnetic resonance (¹³C-NMR), Fourier-transform infrared spectroscopy (FT-IR), electrospray ionization (EIS-MS), thermal analysis (TG), cyclic voltammetry (CV), and ultraviolet-visible spectroscopy (UV-vis), for electrolytes (liquid or dried) in the DSSC charge transportation mechanism. Also, the influence of ion exchange from chloride to iodine in the synthesized electrolytes, compared to other electrolytes (conventional or commercial), was investigated about DSSC performance efficiency. When using as a liquid electrolyte (SM-1), the power conversion efficiency (ƞ) of the working DSSC device was recorded as 1.980% and it was observed that the performances of DSSCs increased up to 56% when comparing dried electrolyte for SM-1 without conventional redox material (I^-/I₃^-). In the future, different molecular modifications of this type of benzimidazole derivatives or mixtures with conventional redox couples may further improve the performance of DSSC devices.     

Synthesis of organic sulfobetaine‐based polymer gel electrolyte for dye‐sensitized solar cell application

We have synthesized eco‐friendly, economic, and equally efficient polysulfobetaine‐based gel electrolyte to the alternative of liquid electrolyte in the fabrication of dye‐sensitized solar cells (DSSCs) for the first time. This nitrogen‐rich and highly conductive polysulfobetaine was synthesized by an easy and facile method without the use of any catalyst and explored for its DSSC application. The synthesized polymer gel electrolyte exhibited good ionic conductivity about 6.8 × 10^?3 Scm^?1 at ambient temperatures. DSSCs were fabricated based on this polysulfobetaine gel electrolyte and studied for their performance based on photovoltaic parameters. The DSSC photovoltaic results were appreciable and are Voc = 0.82 V, Jsc = 11.49 mA/cm², FF = 66%, and PCE = 6.26% at 1 sun intensity. These values are slightly lower than conventional liquid electrolyte‐based DSSC shown as Voc = 0.78 V, Jsc = 12.90 mA/cm², FF = 69%, and PCE = 7.07%, both at 100 mWcm^?2. Conductivity and photovoltaic parameters of the device reveals that as prepared polysulfobetaine‐based polymer gel electrolyte may be useful in the fabrication of DSSC and other electrochemical devices. Copyright © 2017 John Wiley & Sons, Ltd.     

Ionic liquid crystal-based electrolyte with enhanced charge transport for dye-sensitized solar cells

A room temperature ionic liquid crystal,1-dodecyl-3-ethylimidazolium iodide(C12EImI),and an ionic liquid,1-decyl-3-ethylimidazolium iodide(C10EImI),have been synthesized,characterized and employed as the electrolyte for dye-sensitized solar cells(DSSC).The physicochemical properties show that a smectic A(SmA)phase with a lamellar structure is formed in C12EImI.Both C12EImI and C10EImI have good electrochemical and thermal stability facilitating their use in DSSC.The steady-state voltammograms reveal that the diffusion coefficient of I3–in C12EImI is larger than that in C10EImI,which is attributed to the existence of the SmA phase in C12EImI.Because the iodide species are located between the layers of imidazolium cations in C12EImI,exchange reaction-based diffusion is increased with a consequent increase in,the overall diffusion.The electrochemical impedance spectrum reveals that charge recombination at the dyed TiO2/electrolyte interface of a C12EImI-based DSSC is reduced due to the increase in I3–diffusion,resulting in higher open-circuit voltage.Moreover,both short-circuit current density and fill factor of the C12EImI based DSSC increase,as a result of the increasing transport of I3–in C12EImI.Consequently,the photoelectric conversion efficiency of C12EImI-based DSSC is higher than that of the C10EImI–based DSSC.     

Ionic Liquid Based Electrolyte with Mesoporous Silica SBA-15 as Framework for Quasi-solid-state Dye-sensitized Solar Cells

Quasi-solid-state electrolytes were fabricated with mesoporous silica SBA-15 as a framework material. Ionic conductivity measurements revealed that SBA-15 can enhance the conductivity of the quasi-solid-state electrolyte. The diffusion coefficients of polyiodide ions such as Ⅰ3ˉ and Ⅰ5ˉ which were confirmed by Raman spectroscopic measurement, were about twice larger than that of I-. The optimized photoenergy conversion efficiency of dye-sensitized solar cells （DSSC） with the quasi-solid-state electrolyte was 4.3% under AM 1.5 irradiation at 75 mW·cm^-2 light intensity.     

The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells

The effect of polypyrrole (PPy) on the polyvinyl alcohol (PVA)-potassium iodide (KI)-iodine (I₂) polymer electrolytes has been investigated and optimized to use in a dye-sensitized solar cell (DSSC). The different weight ratios of PVA: PPy (93: 2, 91: 4, 89: 6, 87: 8, and 85: 10 wt%) polymer electrolytes (PE) were prepared by solution casting. Structural, complex formation and surface roughness of the prepared electrolytes was confirmed by X-ray diffraction, FTIR, and atomic force microscopy (AFM) respectively. Conductivity plots of all polymer films showed increasing trend with temperature and concentration of PPy. The activation energy of the optimized system found to be 0.871 kJ mol^?1. UV-visible spectrum was adopted to characterize the absorption spectra of the material revealed that increase in the absorbance with increasing PPy content and shifting the absorbance maximum towards lower energy. The indirect band gap decreased from 3.78 to 2.14 eV and direct band gap decreased from 3.88 to 2.71 eV. The EIS analyses revealed the lower charge transfer resistance of 3.029 Ω cm² at the interface between CE and PE. The excellent performance was observed in the fabricated DSSCs using PVA (85%)/PPy (10%)/KI (5%)/I₂ polymer electrolyte with a short-circuit current density of 11.071 mA cm^?2, open-circuit voltage of 0.644 V, fill factor of 0.575, and photovoltaic conversion efficiency of 4.09% under the light intensity of 100 mW cm^?2. Hence, the PPy content in polymer electrolyte influences the remarkable performance of low-cost DSSC.     

Synthesis and Characterization of Donor–π‐Acceptor‐Based Porphyrin Sensitizers: Potential Application of Dye‐Sensitized Solar Cells

New porphyrin sensitizers based on donor–π‐acceptor (D‐π‐A) approach have been designed, synthesized, characterized by various spectroscopic techniques and their photovoltaic properties explored. N,N′‐Diphenylamine acts as donor, the porphyrin is the π‐spacer, and either carboxylic acid or cyanoacryclic acid acts as acceptor. All compounds were characterized by using ¹H NMR spectroscopy, ESI‐MS, UV–visible emission spectroscopies as well as electrochemical methods. The presence of aromatic groups between porphyrin π‐plane and acceptor group push the absorption of both Soret and Q‐bands of porphyrin towards the red region. The electrochemical properties suggests that LUMO of these sensitizers above the TiO₂ conduction band. Finally, the device was fabricated using liquid redox electrolyte (I^?/I₃^?) and its efficiency was compared with that of a leading sensitizer.     

Self-Assembled Graphene/MWCNT Bilayers as Platinum-Free Counter Electrode in Dye-Sensitized Solar Cells

We describe the preparation and properties of bilayers of graphene- and multi-walled carbon nanotubes (MWCNTs) as an alternative to conventionally used platinum-based counter electrode for dye-sensitized solar cells (DSSC). The counter electrodes were prepared by a simple and easy-to-implement double self-assembly process. The preparation allows for controlling the surface roughness of electrode in a layer-by-layer deposition. Annealing under N₂ atmosphere improves the electrode's conductivity and the catalytic activity of graphene and MWCNTs to reduce the I₃⁻ species within the electrolyte of the DSSC. The performance of different counter-electrodes is compared for ZnO photoanode-based DSSCs. Bilayer electrodes show higher power conversion efficiencies than monolayer graphene electrodes or monolayer MWCNTs electrodes. The bilayer graphene (bottom)/MWCNTs (top) counter electrode-based DSSC exhibits a maximum power conversion efficiency of 4.1 % exceeding the efficiency of a reference DSSC with a thin film platinum counter electrode (efficiency of 3.4 %). In addition, the double self-assembled counter electrodes are mechanically stable, which enables their recycling for DSSCs fabrication without significant loss of the solar cell performance.     

Enhanced Electrocatalytic Performance of a Porous g‐C3N4/Graphene Composite as a Counter Electrode for Dye‐Sensitized Solar Cells

A porous graphitic carbon nitride (g‐C₃N₄)/graphene composite was prepared by a simple hydrothermal method and explored as the counter electrode of dye‐sensitized solar cells (DSCs). The obtained g‐C₃N₄/graphene composite was characterized by XRD, SEM, TEM, FTIR spectroscopy, and X‐ray photoelectron spectroscopy. The results show that incorporating graphene nanosheets into g‐C₃N₄ forms a three‐dimensional architecture with a high surface area, porous structure, efficient electron‐transport network, and fast charge‐transfer kinetics at the g‐C₃N₄/graphene interfaces. These properties result in more electrocatalytic active sites and facilitate electrolyte diffusion and electron transport in the porous framework. As a result, the as‐prepared porous g‐C₃N₄/graphene composite exhibits an excellent electrocatalytic activity. In I^?/I₃^? redox electrolyte, the charge‐transfer resistance of the porous g‐C₃N₄/graphene composite electrode is 1.8 Ω cm², which is much lower than those of individual g‐C₃N₄ (70.1 Ω cm²) and graphene (32.4 Ω cm²) electrodes. This enhanced electrocatalytic performance is beneficial for improving the photovoltaic performance of DSCs. By employing the porous g‐C₃N₄/graphene composite as the counter electrode, the DSC achieves a conversion efficiency of 7.13 %. This efficiency is comparable to 7.37 % for a cell with a platinum counter electrode.     

MnWO4/生物质衍生碳纳米复合催化剂的制备及催化性能

通过共沉淀法合成了双金属氧化物MnWO₄镶嵌生物质衍生碳（MnWO₄/BC）纳米复合催化剂,并将其作为对电极（counter electrode,CE）催化剂组装了染料敏化太阳能电池（dye-sensitized solar cell,DSSC）,探究了MnWO₄/BC在非碘体系中的催化性能和光伏性能。结果表明：在铜氧化还原（Cu²⁺/Cu⁺）电对DSSC中获得的光电能量转换效率（power conversion efficiency,PCE）为3.57%（D35）和1.59%（Y123）,高于Pt电极的PCE（3.12%,1.16%）;50次连续循环伏安测试表明,MnWO₄/BC催化剂具有较好的电化学稳定性。     

Quantum dot doped solid polymer electrolyte for device application

ZnS capped CdSe quantum dots embedded in PEO:KI:I₂ polymer electrolyte matrix have been synthesized and characterized for dye sensitized solar cell (DSSC) application. The complex impedance spectroscopy shows enhance in ionic conductivity (σ) due to charges provide by quantum dots (QD) while AFM affirm the uniform distribution of QD into polymer electrolyte matrix. Cyclic voltammetry revealed the possible interaction between polymer electrolyte, QD and iodide/iodine. The photovoltaic performances of the DSSC containing quantum dots doped polymer electrolyte was also found to improve.     

Study of quasi-solid electrolyte in dye-sensitized solar cells using surfactant as pore-forming materials in TiO<Subscript>2</Subscript> photoelectrodes

A novel polymer gel electrolyte was used to improve the performance and long-term stability in dye-sensitized solar cells (DSSCs). The polymer gel electrolyte (PGE) was prepared by mixing 5 wt% poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and 2 % TiO₂ nanoparticles. The conductivity of PGE with P25 reached 9.98 × 10^?3 S/cm, which increased by 34.9 % compared with 7.40 × 10^?3 S/cm of PGE without P25, and the diffusion coefficient was also increased by 19.0 %. Different photoelectrodes were obtained by using three kinds of surfactants (cetylamine, octadecylamine, and P123) as pore-forming materials, and their morphologies were contrasted through scanning electron microscopy (SEM). The results showed that gel electrolyte can increase the short-circuit current density (J _sc) from 11.01 to 12.99 mA/cm² in DSSCs. Moreover, unlike the liquid electrolyte, the gel electrolyte is more conducive to the TiO₂ photoelectrodes with larger pores. In conclusion, the efficiency of DSSC with gel electrolyte and P123 as pore-forming material was 6.73 %, which was 12 % higher than the liquid electrolyte in the same test condition. In addition, the sealed gel electrolyte DSSCs showed better stability than did liquid electrolyte DSSCs during nearly 600 h.     

Non‐classical Design of High‐Efficiency Sensitizers for Dye‐Sensitized Solar Cells

The dye regeneration step in a dye‐sensitized solar cell (DSSC) affects significantly the device efficiency. To be able to predict the dye regeneration efficiency by the electrolyte this paper provides a facile way to design high‐efficiency sensitizers for DSSC. This paper proposes, for the first time, a simple and ingenious way to identify the dye regeneration sites and their relative efficiencies when a specific electrolyte is used. Two steps are proposed to identify the dye regeneration sites and their relative regeneration efficiencies: (1) drawing all the resonance structures of the oxidized dye to determine the regeneration sites, and (2) choosing the most favored site for dye regeneration as the chemically softest (when the redox couple used is soft I⁻/I₃⁻ pair) and the least spatially hindered site. The regeneration sites identified by the resonance structures are consistent with the β‐LUSO (β lowest unoccupied spin orbital) distribution, which is generally used for identifying the dye regeneration sites, calculated with DT‐DFT theory. The relative dye regeneration efficiency and photovoltaic performance of both ruthenium and metal‐free organic dyes predicted by the method reported here are supported by experimental data and the proposed dye regeneration mechanism. Several types of dye molecules are used to demonstrate the correctness of this new tool. This non‐classical tool, which uses the well‐known chemical knowledge of the resonance structure and hard–soft acid–base principle, without any computer calculation or physicochemical measurement, provides a very simple and powerful tool to quickly conceive high‐efficiency sensitizers for DSSCs.     

Recent Advances of Cobalt(II/III) Redox Couples for Dye‐Sensitized Solar Cell Applications

In recent years dye‐sensitized solar cells (DSSCs) have emerged as one of the alternatives for the global energy crisis. DSSCs have achieved a certified efficiency of >11% by using the I^?/I₃^? redox couple. In order to commercialize the technology almost all components of the device have to be improved. Among the various components of DSSCs, the redox couple that regenerates the oxidized sensitizer plays a crucial role in achieving high efficiency and durability of the cell. However, the I^?/I₃^? redox couple has certain limitations such as the absorption of triiodide up to 430 nm and the volatile nature of iodine, which also corrodes the silver‐based current collectors. These limitations are obstructing the commercialization of this technology. For this reason, one has to identify alternative redox couples. In this regard, the Co(II/III) redox couple is found to be the best alternative to the existing I^?/I₃^? redox couple. Recently, DSSC test cell efficiency has risen up to 13% by using the cobalt redox couple. This review emphasizes the recent development of Co(II/III) redox couples for DSSC applications.     

Dye-Sensitized Solar Cell Utilizing TiO<Subscript>2</Subscript> Nanostructure Films: Effect of Synthesis Temperature

This paper is concerned with a study of the influence of synthesis temperature on the properties of TiO₂ films and the performance of dye-sensitized solar cell (DSSC). The TiO₂ film samples synthesized via liquid phase deposition for 5 h at various temperatures, namely, 40, 50, 60, 70 and 80°C. It was found that the morphological shape of the film changes with growth temperature. The optical absorption increases with growth temperature. However, the photoluminescence decreases with growth temperature. These TiO₂ samples were applied in a DSSC of ITO/TiO₂/electrolyte/platinum. The DSSC utilizing the sample grown at 40°C demonstrated the highest photovoltaic parameters with the J_sc, and η of 1.40 mA cm^–2 and 0.44% respectively. This is due to the smallest grain size of TiO₂ films and the smallest bulk resistance of the device.