低量镱掺杂TiO2纳米光催化剂的溶胶-溶剂热制备及光活性

利用溶胶-溶剂热技术制备了锐钛矿型Yb掺杂和未掺杂TiO2纳米粒子,以亚甲基蓝(MB)溶液在紫外光和可见光照射下的光催化脱色率评价其光活性,考察了溶剂热温度、Yb掺杂量和焙烧温度对样品光活性的影响;结合XRD,BET,XPS,FT-IR,DRS和PL表征手段,探讨了Yb掺杂对TiO2光活性的影响机制.结果表明,低量Yb掺杂不仅显著提高TiO2的紫外光活性,也明显提高其可见光活性.Yb掺杂调整TiO2带隙内部电子分布状态,有效抑制光生e-/h+复合,提高量子效率;并且增加表面羟基,增大比表面积,改善表面织构特性,致使紫外光活性提高.然而Yb掺杂并未引起紫外吸收带边红移,其可见光活性的提高应归因于Yb掺杂强化了表面吸附染料的敏化作用.     

N-P-TiO2纳米粒子的溶胶-水热制备及太阳光下光催化降解4-氯酚性能

以尿素和磷酸为掺杂剂、冰醋酸为抑制剂,利用溶胶-水热技术制备了介孔锐钛矿型N-P-TiO2片状纳米粒子;以4-氯酚溶液在模拟太阳光照射下的光催化降解评价其光活性;结合XRD,TEM,BET,XPS,DRS,PL和ζ-电位分析,探讨了N和P掺杂对TiO2光活性的影响机制.结果表明,与未掺杂、N或P单掺杂TiO2相比,N-P共掺杂TiO2具有更高的光催化降解4-氯酚活性.N-P共掺杂TiO2的可见光响应是由N 2p,P 3p分别与O 2p轨道杂化导致带隙窄化引起的.N-P共掺杂产生协同作用,进一步改善TiO2的表面织构特性,增加表面羟基,抑制光生e-/h+复合,增强表面酸性提高其水分散性,导致N-P共掺杂TiO2的光活性提高.     

硼硫共掺杂TiO2的光催化性能及掺杂机理

采用水热法制备了硼硫共掺杂的TiO2光催化剂(TiO2-B-S),并用其光催化降解甲基橙.结果表明,在240℃下水热反应12h时制得的TiO2-B-S具有较高的催化活性,紫外光照射50min和太阳光照射230min时对甲基橙的降解率分别达99.8%和81%.X射线粉末衍射、紫外-可见漫反射光谱和X射线光电子能谱等研究表明,TiO2-B-S为锐钛矿晶型,硫硼掺杂能抑制TiO2粒径的生长;TiO2-B-S同时具有较高的紫外光和可见光活性的原因可能是掺杂的硼以B3 进入晶格中,导致TiO2晶格畸变,带隙变窄.掺杂的硼和硫还提高了TiO2的表面酸度和对可见光的吸收.     

N掺杂TiO_2纳米粒子表面光生电荷特性与光催化活性

以尿素为氮源,采用水热法制备了不同N掺杂量的TiO2(N-TiO2)光催化剂.利用X射线衍射(XRD),紫外-可见漫反射光谱(UV-Vis DRS),X射线光电子能谱(XPS)及荧光(PL)光谱等技术对其进行了系统的表征.以罗丹明B(RhB)和甲基橙(MO)溶液的脱色降解为模型反应,分别考察了N-TiO2光催化剂在紫外和可见光区的光催化活性.利用表面光伏(SPV)和瞬态光伏(TPV)技术研究了N-TiO2纳米粒子表面光生电荷的产生和传输机制,并探讨了光生电荷与光催化活性之间的关系.结果显示,随着N含量的增大,TiO2表面光伏响应阈值红移,可见光部分光电压响应强度逐渐增强,瞬态光伏响应达到最大值的时间亦有着不同程度的延迟.这表明适量的N掺杂能够提高TiO2纳米粒子中光生载流子的分离效率,相应地延长载流子的传输时间,增加光生电荷的寿命,从而促进其光催化活性;而过量的N掺杂则增加了TiO2纳米粒子中光生载流子的复合中心,抑制其光催化活性.     

TiO2-yNx纳米光催化剂的制备及其可见光响应机理

利用溶胶-凝胶技术,以尿素为氮源,采用原位掺杂方式制备了TiO2-yNx纳米粉体;以亚甲基蓝(MB)溶液在可见光下的光催化降解评价其可见光催化活性;考察了体系初始pH值、N的掺杂量和焙烧温度对样品可见光催化活性的影响。 结合XRD、XPS、ESR和DRS测试技术,研究了N掺杂纳米TiO2的可见光响应机理。 研究结果表明,TiO2-yNx纳米粉体的优化制备工艺条件为：体系初始pH=0.52,掺杂比n(N)∶n(Ti)=1∶6,焙烧温度为440 ℃。 此条件下制备的样品N含量为0.77%,为单一的锐钛矿相,平均粒径为19.0 nm,具有良好的可见光催化活性。 N掺杂导致TiO2纳米粉体的表面羟基含量增加,形成了大量束缚单电子的氧空位;N取代晶格O形成了N-Ti-O和O-N-Ti键合结构。 N掺杂导致TiO2纳米粒子的吸收带边红移,对可见光的吸收能力明显增强,这表明N掺杂改变TiO2电子结构,使带隙窄化,降低光响应阈值。 N掺杂TiO2纳米粒子的可见光响应归因于N取代掺杂形成的掺杂能级与氧空位形成的缺陷能级共同作用所致。     

碳和钇共掺杂对混相TiO2光催化性能的影响

TiO2因其毒性低、稳定性高、制备成本低廉而获得广泛应用,特别是作为光催化剂在降解环境污染物方面受到了广泛关注;然而,纯TiO2较大的光生载流子复合率和较宽的带隙限制了其应用.元素掺杂作为一种拓宽光催化剂光吸收能力的方法广泛应用于各种光催化剂的修饰改性,而两种具有光催化性能的TiO2相共存则能有效抑制光生载流子的复合,因此采取合适的方法有效利用这两种TiO2改性的方法制备得到更具实际应用潜质的光催化剂具有一定的可行性.本文通过简单的溶胶-凝胶过程向锐钛矿相与金红石相组成的混相TiO2中共掺杂碳和钇得到了一种活性较高的可见光响应光催化剂.采用粉末X射线衍射、拉曼光谱、X射线光电子能谱和透射电镜等表征手段研究了碳和钇掺杂对TiO2结构的影响,发现碳掺杂有利于金红石相的形成且材料具有更大的晶粒尺寸,钇掺杂则有利于锐钛矿相的形成且能细化材料的晶粒尺寸,提高材料的比表面积,导致材料更好的光催化活性.材料在30 W荧光灯光照条件下的光催化降解亚甲基蓝(MB)性能的研究显示,C-Y-TiO2样品具有比单掺杂和未掺杂样品更高的光催化活性,其顺序为C-Y-TiO2>Y-TiO2>C-TiO2>TiO2≈P25.此外,降解反应动力学研究表明C-Y-TiO2样品光降解MB的速率是未掺杂样品在相同条件下降解速率的3.5倍.不同钇掺杂含量样品的结构和光催化降解MB的研究结果表明,钇掺杂显著促进了锐钛矿相TiO2的形成.这说明钇可能仅掺杂进入锐钛矿相,因此合适的钇掺杂量才能有效形成最优化的光催化性能的混相TiO2.不同热处理温度下获得的样品的光降解MB特性也表明,一定的热处理温度有利于合适的锐钛矿相和金红石相的组成,从而有利于相间的协同效应.紫外-可见光谱和荧光光谱表征分析表明,碳和钇的掺杂都拓展了其吸收光谱到可见光区域,且抑制了光生电子和空穴对的复合,进而提高了材料的光催化活性.碳和钇共掺杂的混相TiO2具有较高可见光光催化活性的主要原因有两个方面:一是元素掺杂减小了TiO2的带隙使得材料具有可见光响应;二是金属和非金属元素在锐钛矿相与金红石相TiO2中不同的掺杂特性形成的协同效应,抑制了光生电子和空穴的复合.     

模拟太阳光下稀土Gd掺杂了TiO2纳米晶的光催化性能研究

以甲基橙的光催化降解为探针反应,采用氙灯模拟自然条件下的太阳光,评价了通过酸催化的溶胶-凝胶法制备的稀土Gd掺杂改性TiO2纳米晶的光催化活性及对甲基橙水溶液TOC的去除效果.运用XRD和UV-Vis DRS表征技术考察了Gd掺杂对纳米TiO2的微晶尺寸、晶体结构与光学性能的影响.结果表明,Gd掺杂可以抑制TiO2由锐钛矿相向金红石相的转变,阻碍TiO2晶粒增长,使TiO2的光吸收带边发生蓝移且有利于对可见光的吸收,从而使Gd掺杂TiO2在模拟太阳光下光催化降解甲基橙的能力得到明显提高,但样品对甲基橙水溶液TOC的去除效果要滞后于其对色度的去除.     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

酸催化水解法制备可见光响应N掺杂纳米TiO2催化剂

 以TiCl4为钛源,采用酸催化水解法合成了TiO2前驱体,在NH3/N2气氛中经程序升温处理制得不同N掺杂量的TiO2可见光响应催化剂. 以苯酚为模型物,考察了催化剂在可见光及紫外光区的催化活性. 采用X射线衍射、紫外-可见漫反射光谱、傅里叶变换红外光谱、扫描电镜和低温氮物理吸附对光催化剂的晶相结构、光谱特征和表面结构进行了表征. 结果表明,掺杂N后锐钛矿TiO2的可见光催化活性显著提高,在500 ℃焙烧5 h制得的催化剂在可见光区及紫外光区均表现出最高的光催化活性. N掺杂对TiO2的晶粒大小、比表面积和晶相结构影响不大. 适量N掺杂可在TiO2表面形成Ti-O-N键,形成了新的能级结构,使催化剂的吸收带边红移至490～550 nm; 同时该结构也可有效提高TiO2的紫外光催化活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.