十六烷基二苯醚二磺酸钠分子有序聚集体的研究

采用芘为荧光探针、二苯甲酮为猝灭剂，以分子荧光探针法首次测定了由刚性基团联接的特殊双亲水基型阴离子表面活性剂——十六烷基二苯醚二磺酸钠(C16-MADS)的胶束聚集数(Nm)，并考察了表面活性剂浓度、无机盐浓度和温度对Nm的影响。结果表明，表面活性剂的浓度必须高于临界胶束浓度(cmc)一个数量级时，才能测定出较为合适的Nm；随着C16-MADS浓度的增大，Nm增大，胶束内核的微极性变小；而温度对Nm的影响极小。与传统的单亲水基阴离子表面活性剂相比，C16-MADS的有序聚集体表现出许多不同之处，如Nm仅为传统的单亲水基阴离子表面活性剂胶束聚集数的一半，无机盐浓度对Nm的影响极小，胶束内核的微极性明显增大。     

稳态荧光探针研究Guerbet醇聚氧乙烯醚羧酸钠的聚集行为

以芘为荧光探针、二苯甲酮为猝灭剂,用稳态荧光探针法测定了合成的4种具有支链结构的Guerbet醇聚氧乙烯醚羧酸钠的临界胶束浓度和胶团的聚集数.结果表明,用稳态荧光探针法得到的临界胶束浓度(CMC)数值与表面张力法相差不大.结合临界胶束浓度、胶束微环境的极性和胶束聚集数的变化规律,推测了这类表面活性剂形成的胶束聚集体的结构形态.     

丙烯酰胺型阴离子表面活性单体的化学结构与其胶束化行为

对两种丙烯酰胺型阴离子表面活性单体(2-丙烯酰胺基十四烷磺酸钠, NaAMC₁₄S; 2-丙烯酰胺基十二烷磺酸钠, NaAMC₁₂S)的化学结构与胶束化行为的关系进行了较深入的研究. 使用紫外分光光度法测定了NaAMC₁₄S, NaAMC₁₂S及十二烷基磺酸钠(SDS)在水中的溶解度, 同时采用表面张力法(环法)测定了它们在不同温度下的临界胶束浓度CMC; 采用稳态荧光探针法测定了不同浓度的胶束聚集数与本征胶束聚集数. 实验结果表明, 与普通表面活性剂相比, 由于丙烯酰胺型阴离子表面活性单体分子中具有两个亲水头基, 在水中的溶解性能较强, 故具有较低的Krafft温度; 在溶液表面的饱和吸附量低, 故降低水表面张力的能力较差, 即表面活性差; 疏水缔合的胶团较为疏松, 故聚集数很小; 胶束内分子间的疏水相互作用较弱, 故临界胶束浓度CMC较高.     

阳离子碳氟表面活性剂研究Ⅰ:水溶液中的胶束特性及生长

利用动态光散射(Dynamic Light Scattering,DLS)、瞬态电双折射(Transient Electric Birefringence,TEB)和粘度测定方法研究了部分氟代阳离子表面活性剂氟代-2-羟基十一烷基二乙羟基甲基氯化铵(diethanolheptadecafluoro-2-undecanol methylammonium chloride,C8F17CH2CH(OH)CH2NCH3(C2H4OH)2Cl,DEFUMACl)水溶液的胶束化特性.结果表明DEFUMACl的临界胶束浓度cmc为3.8 mmol·L-1.稀溶液中随着DEFUMACl浓度的增加或者无机盐NaCl的加入,DEFUMACl胶束由球形向棒状转变,其转变浓度,即第二临界胶束浓度(cmcⅡ)为0.2 mol·L-1;电导测定的反离子(Cl-)结合度为0.72.利用球形和棒状胶束模型确定的DEFUMACl胶束聚集数分别为45和335.     

两性聚电解质PDMA_m-b-PAA_n与表面活性剂(12-6-12)的相互作用

采用Zeta电位、荧光探针、表面张力和黏度等方法研究了碱性条件下不同嵌段比的两性聚电解质聚(N,N-二甲胺基甲基丙烯酸乙酯-b-丙烯酸)(PDMAm-b-PAAn)与阳离子偶联表面活性剂(C12 H25(CH3)2N(CH2)6N(CH3)2C12H25·2Br-)(简称12-6-12)的相互作用.结果表明:由于静电相互作用,两嵌段聚电解质PDMAm-b-PAAn和12-6-12之间可形成类胶束或复合物,PDMA链段的弱亲水性对复合物起到稳定的作用.对同一类型的两嵌段聚电解质,改变两链段的相对长度之比,既不会使其在溶液中的构象发生改变,也不会使其与表面活性剂的相互作用模式发生改变.     

聚L-丙氨酸-聚乙二醇嵌段共聚物纳米胶束的研究

分别以氨基聚乙二醇和氨基聚乙二醇单甲醚为大分子引发剂,采用开环聚合的方法合成了两亲性聚L-丙氨酸-聚乙二醇(PAE)和聚L-丙氨酸-聚乙二醇单甲醚(PAME)两种嵌段共聚物,其结构经1H NMR,IR,DSC,GPC等表征;利用园二色技术研究了其在水溶液中的二级结构,用芘荧光探针技术研究了其胶束的形成及其临界胶束浓度(CMC),利用透射电镜研究了胶束的形态。结果表明,在水溶液中共聚物链以α-螺旋构象形式存在,在一定条件下嵌段共聚物PAE-1,PAE-2,PAME-1和PAME-2能够形成球形的稳定胶束,PAE-1形成胶束的CMC为3.36×10-5mol.L-1,CMC值受嵌段类型和共聚物中聚L-丙氨酸链段含量的影响。     

聚L-丙氨酸-聚乙二醇嵌段共聚物的胶束化行为研究

以氨基聚乙二醇单甲醚(MPEG-NH₂)为大分子引发剂, 采用开环聚合方法合成了聚L-丙氨酸-聚乙二醇嵌段共聚物(PAME), 并对其结构进行了表征; 用圆二色谱(CD)研究了嵌段共聚物在水溶液中的二级结构, 用芘荧光探针技术研究了共聚物胶束的形成及其临界胶束浓度(CMC), 利用动态光散射(DLS)和透射电镜(TEM)研究了胶束的粒径分布和形态. 结果表明, 在水溶液中共聚物链以α-螺旋构象形式存在, 在一定条件下嵌段共聚物能够形成球形的稳定胶束, PAME-1形成胶束的CMC为1.99×10^-5 mol/L, CMC值受共聚物中聚L-丙氨酸(PLA)链段含量的影响.     

氯离子电极的研制及应用研究

以戊巴比妥氯化汞(Ⅱ)为载体,制备了PVC液态膜氯离子选择性电极.电极对Cl-离子呈现高的选择性,其选择顺序为I-＞Br-～SCN-～Salicylate-＞＞ClO-4＞NO-3＞F-＞H2PO-4＞HCO-3＞SO2-4.测定了电极对常见阴离子的选择性,除I-、Br-与SCN-有干扰外,其它阴离子均无明显的干扰;25℃ 时, 在0.05 mol·L-1 H3PO4-NaH2PO4(pH 4.1)溶液中,Cl-离子浓度在6.0 ×10-3～3.5×10-6 mol·L-1 呈线性响应,斜率为57.6 ±2 mV/decade,检出限为2.0 ×10-6 mol·L-1.该法用于氯仿光催化降解微量Cl-离子的测定,取得满意结果.     

阳离子Gemini表面活性剂12-3-12与DNA在模拟体液中的相互作用研究

采用紫外透射光谱、透射电镜、原子力显微镜、圆二色谱(CD)等方法探讨了阳离子Gemini表面活性剂C12H25N+(CH3)2-(CH2)3-(CH3)2N+C12H25·2Br-(12-3-12)与DNA在模拟体液(SBF)中的相互作用。结果表明,SBF中较高反离子浓度不但屏蔽了DNA和12-3-12之间的静电吸引作用,而且促进了12-3-12聚集体的产生和生长,导致低盐条件下体系中出现的沉淀溶解现象的消失。SBF中DNA与12-3-12之间存在强烈的相互作用;随着12-3-12的加入,表面活性剂分子在DNA链周围聚集,类网络结构的DNA逐渐变为类似于串珠的复合物,随后出现尺寸较大的类球形复合物以及较大复合物与较小表面活性剂聚集体共存的现象。CD谱结果显示,SBF中12-3-12可以诱导DNA的构象发生改变,由自然的B构型变成高度致密的ψ相。分子动力学模拟的离子液体中表面活性剂与带相反电荷聚电解质的相互作用过程及模式与实验结果吻合良好。模拟结果也表明,SBF中较高的反离子浓度提高了聚电解质的可压缩程度,导致相同条件下SBF中聚电解质的均方回旋半径远小于稀盐水溶液(10mmol/L Na Br)体系中的聚电解质均方回旋半径。较强的离子强度不但导致体系中聚电解质和带相反电荷表面活性剂之间的相互作用存在"假饱和"现象,而且也造成体系中表面活性剂在聚电解质周围聚集数显著提高。     

N-甲基二乙醇胺用量对水性阳-非离子聚氨酯溶液性能的影响

通过预聚体法合成了水性阳-非离子聚氨酯表面活性剂(CPUS),利用红外光谱和核磁共振谱对聚合物的结构和组成进行了表征.并通过动态光散射(DLS)、透射电镜(TEM)、表面张力仪、稳态流变分析及荧光光谱法等系统研究了阳离子亲水扩链剂N-甲基二乙醇胺(MDEA)用量对CPUS表面张力、临界胶束浓度、流变性、胶束的尺寸、微极性和聚集行为的影响.TEM表明,CPUS胶束呈球形核壳结构.随着MDEA含量的增加,CPUS水溶液表面张力和临界胶束浓度(CMC)先减小后增大,其最低值分别为39.54 m N/m和1.99 g/L,胶束的平均粒径和分布系数逐渐减小.当浓度低于CMC时,光散射强度较低且变化缓慢,当浓度高于CMC时,光散射强度呈现逐渐增长趋势,胶束聚集数逐渐增加.随着MDEA含量的增加,乳液黏度增加,胶束间的相互作用增强,假塑行为增强.荧光光谱法表明随CPUS浓度增加,I1/I3值从1.8降低到1.3,I338/I334值从0.5升高到1.7,表明疏水基团聚集形成疏水微区,芘分子从水相极性环境转移到胶束疏水内核.随着MDEA含量的增加,胶束微极性和形成难度先减小后增加.     

Fluorescence quenching of coumarins by halide ions

Fluorescence quenching of 4-methyl-7-methoxy coumarin (1) and 4-methyl-5-ethoxy-7-methoxy coumarin (2) in aqueous solutions have been studied at different concentrations of halide ions (Cl-, Br-, I-), at room temperature approximately 20 degrees C. It is observed that the fluorescence intensity of both the coumarin compounds (1 and 2) decrease with increase in the concentration of Br- and I- ions but remains almost constant in case of Cl- ion. It is observed that the quenching due to halide ions proceeds via both a diffusional and static quenching processes. The rate constants for diffusional as well as static component of quenching process have been calculated using modified Stern-Volmer relation. It is further observed, that I- ion has very high quenching ability than Br- ion and Cl) ion almost behaves as a non-quencher. It is explained in terms of the sphere of action model by showing that the value of radius of sphere of action of the halide quencher is greater than the sum of the radii of the respective coumarin and quencher. Further, pattern of the quenching ability of the halide quenchers is found to be as I- > Br- > Cl- and interestingly this is in the same order as of their ionization energy. Finally, the present quenching process has been attributed to the electron transfer resulting between colliding species.     

Aggregation behavior of hexadecyltrimethylammonium surfactants with various counterions in aqueous solution

Both thermodynamic and microenvironmental properties of the micelles for a series of cationic surfactants hexadecyltrimethylammonium (C16TAX) with different counterions, F-, Cl-, Br-, NO3-, and (1/2)SO4(2-), have been studied. Critical micelle concentration (CMC), degree of micelle ionization (alpha), and enthalpy of micellization (DeltaH(mic)) have been obtained by conductivity measurements and isothermal titration microcalorimetry. Both the CMC and the alpha increase in the order SO4(2-) < NO3- < Br- < Cl- < F-, consistent with a decrease in binding of counterion, except for the divalent anion sulfate. DeltaH(mic) becomes less negative through the sequence NO3- < Br- < Cl- < F- < SO4(2-), and even becomes positive for the divalent sulfate. The special behavior of sulfate is associated with both its divalency and its degree of dehydration. Gibbs free energies of micellization (DeltaG(mic)) and entropies of micellization (DeltaS(mic)) have been calculated from the values of DeltaH(mic), CMC, and alpha and can be rationalized in terms of the Hofmeister series. The variations in DeltaH(mic) and DeltaS(mic) have been compared with those for the corresponding series of gemini surfactants. Electron spin resonance has been used to assess the micropolarity and the microviscosity of the micelles. The results show that the microenvironment of the spin probe in the C16TAX surfactant micelles depends strongly on the binding of the counterion.     

Suppressed electrostatic ion chromatography with tetraborate as eluent and its application to the determination of inorganic anions in snow and rainwater

Tetraborate is investigated as the eluent ion for suppressed electrostatic ion chromatography (EIC) using a zwitterionic stationary phase. Good separation of a range of inorganic anions (SO4(2-), Cl-, NO3-, Br-, NO3-, ClO3-, and I-) was obtained, with detection limits for highly conducting ions (SO4(2-), Cl-, NO2-, Br- , and NO3-) being less than 8 x 10(-8) M, and for weakly conducting anions (ClO3- and I-) being 2.7 x 10(-7) and 5.8 x 10(-7) M, respectively. Calibration curves were linear up to 1.8 mM of each analyte. Retention times were found to increase with increasing eluent concentration and a linear relationship was observed between log k' and log[Na2B4O7] for all analytes. This behaviour is attributed to the progressive formation of a binary electrical double layer at the surface of the zwitterionic stationary phase. Retention times of analytes could be manipulated by varying the concentration of the eluent. This new suppressed-EIC system was applied to the determination of inorganic anions (SO4(-2) , CI-, NO3-, NO2-, and Br-) in snow and rainwater samples.     

Ionic liquid-induced changes in the properties of aqueous sodium dodecyl sulfate solution: effect of acidic/basic functional groups

The effects of ionic liquids 1-(2-aminoethyl)-3-methylimidazolium chloride ([MimAE]Cl), 1-carboxylmethyl-3-methylimidazolium chloride ([MimCM]Cl), 1-(2-hydroxylethyl)-3-methylimidazolium chloride ([MimHE]Cl), and 1-ethyl-3-methylimidazolium chloride ([Emim]Cl) on the physicochemical properties of aqueous sodium dodecyl sulfate (SDS) solutions were studied. Compared with [Emim]Cl, the presence of amino group can further facilitate the micellization of SDS, while the opposite result is observed as carboxyl group is imparted. No obvious changes in critical micelle concentration (CMC) and $ {\gamma_{\mathrm{CMC}}} $ values are induced by the neutral hydroxyl group. Only the addition of [MimAE]Cl drastically increases the micellar size. Significant decrease in CMC and increase in micellar size were observed with decreasing pH of [MimAE]Cl solution. The increase in pH of [MimCM]Cl solution results in a slight increase in CMC and decrease in micellar size. ¹H NMR spectra revealed the amino groups are adsorbed at the micellar surface, while the carboxyl groups/carboxylate ions and hydroxyl groups tend to point towards bulk water.     

Anion selectivity in zwitterionic amide-functionalised metal salt extractants

Amide-functionalised salen ligands capable of extracting metal salts have been synthesised and characterised. Single-crystal X-ray structure determinations of complexes of NiSO4, [Ni(L)(SO4)], confirm that the ionophores are in a zwitterionic form with Ni(II) bound in the deprotonated salen moiety and the SO4(2-) ion associated with protonated pendant N'-amidopiperazine groups. Treatment of [Ni(L)(SO4)] with base removes the protons from the pendant amido-amine group resulting in loss of the SO4(2-) ion and formation of metal-only complexes of type [Ni(L-2H)], which have been characterized by single-crystal X-ray diffraction. Three of the ligands with solubilities suitable for solvent extraction studies show loading and stripping pH-profiles that are suitable for the recovery of CuSO4 or CuCl2 from industrial leach solutions. The copper-only complexes, [Cu(L-2H)], are selective for Cl- over SO4(2-) in both solvent extraction and bulk liquid membrane transport experiments and were found to bind Cl- in two steps via the formation of a 1:1:1 [Cu(L-H)Cl] assembly, followed by a 1:1:2 [Cu(L)Cl2] assembly as the pH of the aqueous phase is lowered. The anion transport selectivity was evaluated for a number of other mono-charged anions and interestingly the ligands were found to display a preference for the Br- ion. To probe the influence of the Hofmeister bias on the selectivity of anion complexation, single-phase potentiometric titration experiments were employed to investigate the binding of SO4(2-) and Cl- by one of the copper only complexes, [Cu(L-2H)] in 95 %/5 % MeOH/water. Under these conditions selectivity was reversed (SO4(2-)>Cl-) confirming that the Hofmeister bias, which reflects the relative hydration energies of the anions, dominates the selectivity of anion extraction from aqueous media into CHCl3.     

Hydrothermal and structural chemistry of the zinc(II)- and cadmium(II)-1,2,4-triazolate systems

Hydrothermal reactions of 1,2,4-triazole with zinc and cadmium salts have yielded 10 structurally unique materials of the M(II)/trz/Xn- system, with M(II)=Zn and Cd and Xn-=F-, Cl-, Br-, I-, OH-, NO3-, and SO(4)2- (trz=1,2,4-triazolate). Of the zinc-containing phases, [Zn(trz)2] (1), [Zn2(trz)3(OH)].3H2O (3.3H2O), and [Zn2(trz)(SO4)(OH)] (4) are three-dimensional, while [Zn(trz)Br] (2) is two-dimensional. All six cadmium phases, [Cd3(trz)3F2(H2O)].2.75H2O (5.2.75H2O), [Cd2(trz)2Cl2(H2O)] (6), [Cd3(trz)3Br3] (7), [Cd2(trz)3I] (8), [Cd3(trz)5(NO3)(H2O)].H2O (9.H2O), and [Cd8(trz)4(OH)2(SO4)5(H2O)] (10), are three-dimensional. In all cases, the anionic components Xn- participate in the framework connectivity as bridging ligands. The structural diversity of these materials is reflected in the variety of coordination polyhedra displayed by the metal sites: tetrahedral; trigonal bipyramidal; octahedral. Structures 3, 5, and 7-9 exhibit two distinct polyhedral building blocks. The materials are also characterized by a range of substructural components, including trinuclear and tetranuclear clusters, adamantoid cages, chains, layers, and complex frameworks.     

维生素B1-银胶体系SERS受卤离子竞争吸附的影响

利用傅里叶变换.表面增强拉曼光谱(FT-SERS)研究了卤素离子(Cl-、Br-、I-)对维生素B1(VB1)分子表面增强拉曼散射光谱(SERS)的影响.实验结果表明,在此体系中加入卤素离子则SERS效应减弱,且三种卤素离子在银胶上的吸附能力顺序为I->Br->Cl-.     

离子液体1-烷基-3-甲基咪唑四氟硼酸盐在水溶液中的聚集行为

采用等温滴定量热法、静态荧光猝灭法和电导法系统研究了典型离子液体1-烷基-3-甲基咪唑四氟硼酸盐([Cnmim][BF₄])在水溶液中的聚集行为, 获得了胶束形成的临界胶束浓度(cmc), 摩尔焓变(ΔH_mic), 摩尔吉布斯自由能变(ΔG_mic), 摩尔熵变(ΔS_mic)以及不同浓度时[Cnmim][BF₄]胶束的平均聚集数等基本参数. 发现这类离子液体的聚集为熵驱动, 阳离子的烷基链越长, ΔG_mic越负, 聚集更容易发生. 此外, 结合[C_nmim]X (X=Cl^-, Br^-)的相关研究发现, 阳离子相同时, 体积越大和疏水性越强的阴离子与头基的结合能力越强, 能有效地降低头基之间的静电排斥, 降低cmc, 利于胶束的形成. 对于[C₁₂mim][BF₄], 添加剂β-环糊精(β-CD)的加入可使cmc增大, ΔH_mic和ΔS_mic减小, 而KBF₄则可使cmc和ΔH_mic减小, ΔS_mic增大.     

Conductivities, volumes, fluorescence, and aggregation behavior of ionic liquids [C4mim][BF4] and [C(n)mim]Br (n = 4, 6, 8, 10, 12) in aqueous solutions

Densities, conductivities, and polarity indexes of pyrene for aqueous solutions of a series of ionic liquids [C(n)mim]Br (n = 4, 6, 8, 10, 12) and [C4mim][BF4] have been determined at 298.15 K as a function of ionic liquid concentrations. It was shown that possible aggregation appeared for the ionic liquids in aqueous solutions except for [C4mim]Br. The critical aggregation concentration (CAC) of the ionic liquids, the ionization degree of aggregates (beta), the standard Gibbs energy of aggregation (Delta G(m)(o)), the limiting molar conductivity (Lambda(m)(o)), and the standard partial molar volume (V(m)(o)) for the ionic liquids were derived from the experimental data. The dependence of the CAC, Delta G(m)(o), Lambda(m)(o), and V(m)(o) on the length of the alkyl chain of the cations was examined. It was further suggested from volumetric data that a micelle was formed for [C8mim]Br, [C10mim]Br, and [C12mim]Br in aqueous solutions. Their apparent molar volumes at the critical micelle concentration (V Phi,CMC), apparent molar volumes in the micelle phase (V(Phi)(mic)), and the change of their apparent molar volume upon micellization (Delta V Phi,m) were calculated by application of the pseudophase model of micellization. In addition, the average aggregation number of [C(n)mim]Br (n = 8, 10, 12) has been determined by the steady-state fluorescence quenching technique, and predicted from a simple geometrical mode. It is found that the experimental values are in good agreement with the predicted ones.     

Interfacial ion pairing at the interface between water and a room-temperature ionic liquid, N-tetradecylisoquinolinium bis(pentafluoroethylsulfonyl)imide

The specific interaction of N-tetradecylisoquinolinium (C(14)Iq+) with Cl- and Br- has been detected in the voltammetry of ion transfer and electrocapillarity at the interface between an aqueous solution (W) and a room-temperature ionic liquid (RTIL), N-tetradecylisoquinolinium bis(pentafluoroethylsulfonyl)imide ([C(14)Iq+][C(2)C(2)N-]). This specific interaction also makes the transfer of Cl- and Br- into [C(14)Iq+][C(2)C(2)N-] energetically more favorable in comparison with that of F- and SO(4)(2-). The width of the polarized potential window in ion-transfer voltammetry at the [C(14)Iq+][C(2)C(2)N-]|W interface is significantly narrower because of the transfer of anions from W to RTIL. The degree of affinity of the anion with C(14)Iq+ agrees with the Hofmeister series. Such an ion-pair formation of anions in W with cations in the RTIL is much weaker when the cation constituting the RTIL is a symmetric tetraheptylammonium ion.