聚丙烯熔融接枝马来酸酐反应机理的研究

改变聚丙烯（PP）熔融接枝马来酸酐（MAH）反应中的单体和引发剂的浓度以及添加适当助剂,考察了接枝产物的接枝率和恒定剪切应力（600kPa)及温度（210℃）下的剪切粘度,验证了作先前所提出的PP熔融接枝MAH的反应机理。即：在PP熔融接枝MAH的过程中,过氧化物自由基在熔融接枝过程中直接引发MAH单体及MAH单体在聚丙烯的大分子链段发生β断裂前直接被其引发而产生的接枝反应是影响产物的接枝率和分子量的关键。在不改变单体和引发剂浓度的情况下,降低过氧化物自由基在熔融接枝过程中直接引发MAH单体反应的程度而提高聚丙烯的大分子自由基直接引发MAH单体的反应趋势,是提高接枝产物接枝率和分子量的有效途径。     

β晶型成核剂对聚丙烯力学及结晶性能的影响

研究了N,N′-二环己胺基对苯二酰胺作为β成核剂对聚丙烯(PP)力学性能及结晶性能的影响。结果表明,成核剂具有使聚丙烯增韧的优异性能,当添加质量分数为0.3%时,其抗冲击强度由原来的36.06 J/m2提高到65.79 J/m2。DSC研究表明,添加β成核剂可以诱导PP中β晶生成。考察了冷却速率对结晶温度的影响,当冷却速率为10℃/m in时,结晶温度从118.38℃提高到124.53℃,表明该成核剂的加入使结晶向高温方向偏移,结晶速度加快。     

PP-g-(MAH/St)和PP-g-MAH对聚丙烯/木粉复合材料性能的影响

在转矩流变仪中用熔融接枝法制备马来酸酐(MAH)和苯乙烯(St)接枝聚丙烯（PP）-PP-g-(MAH/St)和PP-g-MAH,将其作为聚丙烯/木粉复合材料的相容剂。 FTIR证实MAH和St单体与PP发生接枝反应。 用SEM和DSC等手段考察两种相容剂对PP/木粉复合材料微观形貌和结晶性能的影响,探索了各种PP/木粉复合材料加工和力学性能不同的内在原因。 SEM显示,PP-g-(MAH/St)改性木粉比PP-g-MAH改性木粉在PP基体中分散性更佳,木粉与PP的界面更加模糊,相容性进一步改善。 DSC结果表明,PP-g-(MAH/St)改性体系可增强木粉对PP的异相成核作用,提高结晶温度和结晶度。 复合材料的加工和力学性能测试结果表明,PP-g-(MAH/St)改性效果明显优于PP-g-MAH。 复合材料的熔体质量流动速率随相容剂用量的增加而逐步下降,PP-g-(MAH/St)改性体系拉伸强度和弯曲强度却逐步上升,并在相容剂用量为4.8 g/100 g PP时达到极值。 此时其拉伸强度达40.62 MPa,分别是未改性体系和PP-g-MAH改性体系的1.29和1.17倍;其弯曲强度达45.72 MPa,分别是未改性体系和PP-g-MAH改性体系的1.23和1.59倍;而无缺口冲击强度却在相容剂用量为3.6 g/100 g PP时达到极值13.35 kJ/m2,分别是未改性体系和PP-g-MAH改性体系的1.62倍和1.42倍。     

大分子相容剂改性Mg(OH)2/PP阻燃材料的性能

用双螺杆挤出机熔融挤出法制备了相容剂改性氢氧化镁/聚丙烯[Mg(OH)2/PP]阻燃材料。研究了马来酸酐接枝聚丙烯(PP-g-MA),马来酸酐接枝(乙烯/辛烯)共聚物(POE-g-MA)和马来酸酐接枝聚醋酸乙烯酯(EVA-g-MA)3种大分子相容剂对阻燃材料的熔体流动性、结晶行为、力学性能和断口形态的影响。结果表明:相容剂PP-g-MA和POE-g-MA的加入使阻燃材料的熔体流动速率降低,PP结晶温度提高,EVA-g-MA的加入使阻燃材料熔体流动速率数提高;Mg(OH)2对PP结晶存在异相成核作用,Mg(OH)2的加入使PP的冲击强度、拉伸强度和断裂伸长率降低,杨氏模量提高;相容剂改性后Mg(OH)2/PP阻燃材料的拉伸强度提高,其中以PP-g-MA最为明显,而POE-g-MA则提高了阻燃材料的冲击强度。     

PP-g-MAH对聚丙烯/滑石粉复合材料的性能影响

研究了两种马来酸酐接枝聚丙烯（PP-g-MAH）在不同含量时对聚丙烯（PP）/滑石粉复合材料的力学性能、雾化性能和线性膨胀系数的影响.结果表明,接枝物的加入能提高复合材料的拉伸性能、冲击性能和弯曲性能,但随着含量的增加拉伸强度、冲击强度和弯曲强度及弯曲模量有所降低.在含量相同时,接枝物1对冷凝组份的影响更小.复合材料的线性膨胀系数随接枝物含量的增加先减小后增加.     

助剂对可生物降解聚碳酸亚丙酯/聚丙烯非织造布切片性能的影响

采用熔融共混法研究助剂马来酸酐(MAH)、马来酸酐接枝聚丙烯(PP-2)对可生物降解聚碳酸亚丙酯(PPC)/聚丙烯(PP)非织造布切片结构与性能的影响.红外谱图表明MAH和PP-2的酸酐官能团与PPC发生了开环反应.MAH、PP-2可显著提高切片的拉伸强度,当MAH,PP-2用量为1%和2%时,切片拉伸强度较不添加助剂时分别提高了116%和101%.MAH,PP-2的加入降低了切片的熔体流动速率,提高了特性黏数,同时提高了切片的玻璃化转变温度(Tg)和热分解温度,扩大了切片的使用和加工温度范围.当MAH用量为1%时,切片Tg提高了4℃.当MAH,PP-2用量为1%和2%时,切片5%热分解温度分别提高了44℃和20℃.加入MAH、PP-2的切片断面的微观形貌图显示切片内部凹陷和空洞较少,较为平整,PP-2改善切片相容性的效果优于MAH.PPC和PP置于磷酸缓冲液中30天的降解率分别为4.30%和0%,说明PP在磷酸缓冲液中几乎不降解.加了助剂的切片30天的降解率在3.80%以上,说明制备的PPC/PP非织造布切片是可降解的,对环境友好.开环反应、增加切片界面黏附力、降低界面张力等可能是助剂提高切片性能的作用机理.     

GMA/苯乙烯多组分单体接枝聚丙烯结晶行为研究

使用差示扫描量热计 (DSC)研究了甲基丙烯酸缩水甘油酯 苯乙烯 (GMA St)多单体熔融接枝聚丙烯[PP g (GMA co St) ]的等温和非等温结晶行为 ,用偏光显微镜观察了结晶的形态 ,并利用Avrami方程对其结晶动力学进行了分析 .研究发现接枝聚丙烯的结晶模式与PP相似 ,属于异相成核控制的球晶三维生长 ;但接枝聚丙烯的结晶温度 (Tc)显著提高 ,幅度高达 16～ 19℃ ,总结晶速率与纯PP相比明显加快 .接枝聚丙烯上GMA co St支链的存在 ,降低了成核界面自由能 ,促进了聚丙烯结晶的异相成核 .在接枝率不太高的情况下 ,随着接枝率的提高 ,接枝聚丙烯的结晶温度升高 ,总结晶速率加快 .在高接枝率范围内 ,随着接枝率的提高 ,接枝PP的Tc 不再升高 ,且由于接枝链的增长严重阻碍了球晶生长 ,导致接枝PP的总结晶速率反而随接枝率的升高而下降     

悬浮法合成聚丙烯接枝丙烯酸

用过氧化二苯甲酰作引发剂以水相悬浮法合成聚丙烯接枝丙烯酸。通过反应条件、组分等因素对PP的接枝率和接枝效率的影响研究,确定较佳配比工艺条件：溶用莳8-0min;反应温度90℃;反应时间90min;在氮气气氛中,丙烯酸7％;过氧化二苯甲酰3．3％;二甲苯25％;水和聚丙烯的重量比为3：1;若加入适量催化剂（1－1．7％0异氰尿酸三烯丙酯能显著提高接枝率。用此PP－g-AA作CaCO3、PP/PA6和合物的相容剂,材料的力学性能有很大的提高。     

可生物降解聚碳酸亚丙酯(PPC)/相容剂/聚丙烯(PP)纺粘非织造布切片性能研究

采用熔融共混法制备可生物降解聚碳酸亚丙酯(PPC)/相容剂/聚丙烯(PP)纺粘非织造布切片,分别研究相容剂马来酸酐(MAH)、马来酸酐接枝聚丙烯(PP-2)、马来酸酐-苯乙烯接枝聚丙烯(PP-g-(MAH-coSt))对切片性能的影响.当mPPC∶mPP为70∶30时,相容剂MAH、PP-2、PP-g-(MAH-co-St)的最优用量分别为PPC和PP总质量的1%、3%、8%,在最优用量下PPC/相容剂/PP纺粘非织造布切片的拉伸强度分别为20.16、21.27、26.34 MPa,熔体流动速率(MFR)分别为81.6 g/10min、103.6 g/10min、46.4 g/10min,T-5%较不添加相容剂时提高了50.5、10.0、28.0 K,扫描电镜图显示加了相容剂的切片内部结构紧密,相容性较好,30天降解率在3.12%以上.红外和核磁谱图表明相容剂PP-g-(MAH-co-St)的作用机理是其酸酐基团和PPC发生了开环反应,通过化学键作用促进PPC与PP相容.相容剂改善了切片的力学性能、热学性能和降解性能,提高了切片的界面粘附力和相容性,在满足纺粘生产工艺下,切片的综合性能和加工温度范围得到提高,为制备具有良好综合性能的可生物降解纺粘非织造布切片提供了理论数据.     

马来酸酐化1,2-聚丁二烯熔融接枝聚丙烯木塑复合材料相容剂的研究

采用熔融接枝法,将马来酸酐化1,2-聚丁二烯(MAPB)在过氧化二异丙苯(DCP)的存在下接枝到聚丙烯(PP)上。使用傅里叶变换红外光谱(FTIR)、热重分析(TG)和差示扫描量热(DSC)法对接枝产物进行表征,将其作为木塑复合材料(WPCs)界面相容剂,以复合材料力学性能为指标对接枝工艺配方进行评价。结果表明:MAPB可以与PP发生接枝反应,并且MAPB的加入能够提高PP的结晶温度和热稳定性。当接枝反应温度为180℃,质量比m(MAPB)∶m(PP)∶m(DCP)=13∶37∶0.2时,所制得的接枝产物对木塑复合材料力学性能提高有最好的效果,以此来确定MAPB-g-PP的工艺配方。     

1,6-己二醇二丙烯酸酯和苯乙烯多单体熔融接枝制备长支链聚丙烯研究

采用哈克转矩流变仪制备了1,6-己二醇二丙烯酸酯(HDDA)和苯乙烯(St)多单体熔融接枝聚丙烯(PP)体系.红外测试结果表明St的加入能够促进HDDA接枝到PP主链,提高接枝率.动态流变行为研究结果也表明采用多单体熔融接枝PP更有利于体系在熔融接枝中生成长支链(LCB).随着St单体添加量的增加,HDDA的接枝率增大...     

Synthesis,stereocomplex crystallization and properties of poly(l‐lactide)/four‐armed star poly(d‐lactide) functionalized carbon nanotubes nanocomposites

Functionalized carbon nanotubes (F‐CNTs) were synthesized through the nucleophilic substitution reaction between four‐armed star poly(d ‐lactide) (4PDLA) and acryl chloride of carbon nanotubes and were characterized using Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy and thermogravimetric analysis. The results indicated that the 4PDLA was successfully grafted onto carbon nanotubes, and it contained 45.5 wt% of 4PDLA. Poly(l ‐lactide) (PLLA) nanocomposites with different F‐CNTs content were prepared by solution casting. Optical microscopy and scanning electron microscopy results showed that F‐CNTs were uniformly dispersed in the nanocomposites. Crystallization behavior and crystal structure of PLLA nanocomposites were investigated using differential scanning calorimetry, polarizing microscope and X‐ray diffraction. The results found that poly(lactide) stereocomplex crystal could be formed between PLLA and F‐CNTs. F‐CNTs played different roles in the process of solution casting and melting crystallization. Polarizing microscope also revealed that crystallization temperature had a significant effect on the nucleation and spherulites growth of PLLA. Thermal stability and mechanical properties of the nanocomposites were also investigated by thermogravimetric analysis, dynamic mechanical analysis and tensile testing. These results demonstrated that the addition of F‐CNTs obviously improved thermal stability and tensile strength of PLLA. The results showed that PLLA/F‐CNTs would have potential values in engineering fields. Copyright © 2015 John Wiley & Sons, Ltd.     

Grafting of functional maleimides onto oligo‐ and polyolefins

In this paper the modification of polyolefins, especially polypropylene (PP), with maleimides is discussed. As there are many problems associated with the analysis of the grafting reaction, commercially available squalane and eicosane were used as model compounds for ethylene‐propylene‐copolymer (EPR) and polyethylene (PE). 2,4,6,8‐Tetramethylnonane (TMN) was synthesized as a novel model compound for PP. N‐Phenylmaleimide and maleimido benzoic acid were grafted onto the oligomers in solution using 2,5‐dimethyl‐2,5‐di‐(tert‐butyl‐peroxy)‐3‐hexyne (Luperox 130) as radical initiator. The grafting efficiency was determined by NMR‐, UV‐spectroscopy, gravimetry and gas‐chromatography. The influence of several reaction parameters on homopolymerformation, amount of modified oligomer and grafting efficiency could be elaborated. NMR‐spectroscopy and SEC were used to analyse the nature of the grafts. Grafting yields were almost quantitative using up to more than 10 mol% monomer, but dropped at higher monomer concentrations to about 60%. The amount of modified oligomer could be increased with higher monomer concentrations or reaction temperatures. Grafting of polymers was done by reactive extrusion. Products were analysed by IR‐spectroscopy. Optimal grafting yields could be achieved with 1 wt% monomer and 0.5 wt% peroxide concentration.     

Preparation and enhanced properties of poly(propylene)/ silica‐grafted‐hyperbranched polyester nanocomposites

A series of poly(propylene) silica‐grafted‐hyperbranched polyester nanocomposites by grafting the modified hyperbranched polyester (Boltorn? H20), possessing theoretically 50% end carboxylic groups and 50% end hydroxyl groups, which endcapped with octadecyl isocyanate (C19), onto the surface of SiO₂ particles (30 nm) through 3‐glycidoxy‐propyltrimethoxysilane (GPTS) was prepared. The effect of silica‐grafted‐modified Boltorn? H20 on the mechanical properties of polypropylene (PP) was investigated by tensile and impact tests. The morphological structure of impact fracture surface and thermal behavior of the composites were determined by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The melt viscosity of composites was investigated by melt flow index (MFI). The obtained results showed that: (1) the modified Boltorn? H20 was successfully grafted onto the SiO₂ surface confirmed by FT‐IR and X‐ray photoelectron spectroscopy (XPS) analysis; (2) the incorporation of silica‐grafted‐modified Boltorn? H20 (3–5 wt% SiO₂) greatly enhanced the notched impact strength as well the tensile strength of the composites; (3) the incorporation of silica‐grafted‐modified Boltorn? H20 had no influence on the melting temperature and crystallinity of PP phase; (4) the MFI of PP composites increased when the silica‐grafted‐modified Boltorn? H20 particles were added compared with PP/SiO₂ or PP/SiO₂‐GPTS composites. Copyright © 2004 John Wiley & Sons, Ltd.     

Thermal,physico‐mechanical,and morphological properties of HDPE graft‐copolymerized with polystyrene

In this study, polystyrene was graft‐copolymerized onto high‐density polyethylene (HDPE) by in situ polymerization of styrene monomer to change the physico‐mechanical and thermal properties of HDPE. The grafting was carried out in a Brabender‐type static mixer by injecting styrene monomer directly into the molten HDPE in the presence of a free‐radical initiator (lauroyl peroxide or LP). The effect of wt% of styrene and initiator concentrations on thermal, physico‐mechanical, and morphological properties of HDPE was investigated. The neat and modified HDPE was characterized by differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and also by tensile strength and contact angle measurements. It was found that the increase in wt% of styrene and LP dosage reduced elongation at break, hygroscopic expansion and also the melting, and the crystallization temperatures of HDPE but increased its tensile strength. The tensile strength was increased from 14.6 MPa for the neat HDPE to 20.6 MPA for the 10 wt% of styrene grafted onto HDPE using 0.8% LP. Scanning electron microscopy results show that there was no phase separation, and the grafted polystyrene became integral part of HDPE. The results demonstrate that styrene could be used in melt compounding to improve various properties of HDPE. Copyright © 2015 John Wiley & Sons, Ltd.     

Study of elastomeric polyurethane nanocomposites prepared from grafted organic–montmorillonite

4,4′-Diphenylmethane diisocyanate (MDI) was grafted on to organic–montmorillonite (OMMT) by reaction between hydroxyl groups (−OH) on surface of the montmorillonite and the isocyanate groups (−NCO) of MDI, thus forming grafted organic–montmorillonite (MOMMT). Intercalated nanocomposites based on polyurethane (PU) and MOMMT were prepared by solution intercalation technology. The interface interaction of PU/MOMMT nanocomposites was better than that of PU/MMT composites. The tensile strength, elongation at break, and tear strength of the PU/MOMMT nanocomposites increased for MOMMT content up to 5% w/w, and then decreased with further increase in MOMMT content. At the same filler content, the tensile strength and tear strength of PU/MOMMT nanocomposites were higher than those of PU/OMMT nanocomposites, whereas the elongations at break of PU/MOMMT nanocomposites were smaller than those of PU/OMMT nanocomposites. The initial temperatures of weight loss of PU/MOMMT nanocomposites were lower than for PU/MMT composites in the first step of thermal degradation, whereas in the second step initial temperatures of weight loss were higher for PU/MOMMT nanocomposites.     

Influence of SEBS-g-MA on morphology, mechanical, and thermal properties of PA6/PP/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organically modified clay (organoclay) toughened with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA) were prepared by melt compounding using co-rotating twin-screw extruder followed by injection molding. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize the structure of the nanocomposites. The mechanical properties of the nanocomposites were determined by tensile, flexural, and notched Izod impact tests. The single edge notch three point bending test was used to evaluate the fracture toughness of SEBS-g-MA toughened PA6/PP nanocomposites. Thermal properties were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). XRD and TEM results indicated the formation of the exfoliated structure for the PA6/PP/organoclay nanocomposites with and without SEBS-g-MA. With the exception of stiffness and strength, the addition of SEBS-g-MA into the PA6/PP/organoclay nanocomposites increased ductility, impact strength and fracture toughness. The elongation at break and fracture toughness of PA6/PP blends and nanocomposites were increased with increasing the testing speed, whereas tensile strength was decreased. The increase in ductility and fracture toughness at high testing speed could be attributed to the thermal blunting mechanism in front of crack tip. DSC results revealed that the presence of SEBS-g-MA had negligible effect on the melting and crystallization behavior of the PA6/PP/organoclay nanocomposites. TGA results showed that the incorporation of SEBS-g-MA increased the thermal stability of the nanocomposite.     

超支化聚乙烯亚胺接枝二氧化硅的制备及在聚丙烯改性中的应用

首先利用3-缩水甘油氧基丙基三甲氧基硅烷(简称GPS)作为偶联剂,对纳米SiO2进行表面改性,获得表面含有环氧基的SiO2纳米粒子(SiO2-GPS).利用这些环氧基与超支化聚乙烯亚胺(HPEI)分子中的氨基进行反应,得到SiO2接枝超支化聚乙烯亚胺的纳米粒子(SiO2-GPS-g-HPEI).然后利用SiO2-GPS-g-HPEI与聚丙烯(PP)和PP接枝的马来酸酐(PP-g-MAH)共混、模压,制备PP/SiO2-GPS-g-HPEI/PP-g-MAH复合材料.红外光谱测试和热失重分析(TGA)测试结果表明,SiO2纳米粒子表面依次接枝了GPS和HPEI;扫描电子显微镜(SEM)的测试结果显示,SiO2-GPS-g-HPEI在聚丙烯基体中分散良好,其材料的冲击断裂为韧性断裂;复合材料共混时,扭矩的增加证明了共混物中分散相(SiO2-GPS-g-HPEI)与基体(PP/PP-g-MAH)界面之间存在一定的相互作用.少量SiO2-GPS-g-HPEI加入PP/PP-g-MAH中,冲击强度可增加96.3%,拉伸强度也有较大的提高.