Evidence of free carrier concentration gradient along the c-axis for undoped GaN single crystals

Results of measurements of infrared reflectivity and micro-Raman scattering on the undoped GaN high pressure grown single crystals are reported. These crystals have usually a high electron concentration due to unintentional doping by oxygen. We show, by the shift of the plasma edge (infrared reflectivity measurements), that the free electron concentration is always higher on the (0 0 0  )N face of the GaN single crystal than on the (0 0 0 1)Ga face. In order to determine the profile of the free carrier concentration, we performed transverse micro-Raman scattering measurements along the (0 0 0 1) c-axis of the crystal with spatial resolution of 1 μm. Micro-Raman experiments give a quantitative information on the free carrier concentration via the longitudinal optical phonon–plasmon (LPP) coupling modes. Thus, by studying the behavior of the LPP mode along the c-axis, we found the presence of a gradient of free electrons. We suppose that this gradient of electrons is due to the gradient of the main electron donor, in undoped GaN single crystals, i.e. oxygen impurity. We propose a growth model which explains qualitatively the incorporation of oxygen during the growth of GaN crystal under high pressure of nitrogen.     

Investigation of preparation and properties of epitaxial growth GaN film on Si(1 1 1) substrate

In this paper, a single crystalline GaN grown on Si(1 1 1) is reported using a GaN buffer layer by a simple vacuum reactive evaporation method. Scanning electron microscopy (SEM), X-ray diffraction (XRD), photoluminescence measurement (PL), and Hall measurement results indicate that the single crystalline wurtzite GaN was successfully grown on the Si(1 1 1) substrate. The surface of the GaN films is flat and crack-free. A pronounced GaN(0 0 0 2) peak appears in the XRD pattern. The full-width at half-maximum (FWHM) of the double-crystal X-ray rocking curve (DCXRC) for (0 0 0 2) diffraction from the GaN epilayer is 30 arcmin. The PL spectrum shows that the GaN epilayer emits light at the wavelength of 365 nm with an FWHM of 8 nm (74.6 meV). Unintentionally doped films were n-type with a carrier concentration of 1.76×10¹⁸/cm³ and an electron mobility of 142 cm³/V s. The growth technique described was simple but very powerful for growing single crystalline GaN films on Si substrate.     

Correlations between photoluminescence and Hall mobility in GaN/sapphire grown by metalorganic chemical vapor deposition

We have investigated photoluminescence (PL) and electron Hall mobility for unintentionally doped GaN epitaxial layers grown by low-pressure metalorganic chemical vapor deposition on c-plane Al₂O₃ substrates. Four GaN films having identical dislocation density but remarkably different electron Hall mobility were exploited. At low temperature (12 K), a PL line associated with a bound exciton was observed and strong correlations were found between the Hall mobility and the PL intensity of the exciton transition. That is, relative PL intensity of the bound exciton to a donor-bound exciton monotonously increased with decreasing the electron mobility of the GaN films. This correlation was interpreted in terms of electrical compensation. Efforts to find the chemical origin of the PL line led to the conclusion that the BE line originated neither from threading dislocations nor from extrinsic point defects. Intrinsic acceptors such as Ga vacancy and GaN anti-site were suspected as plausible origin.     

Laser heated pedestal growth of orthorhombic SrHfO3 single crystal fiber

SrHfO₃ single crystal fibers were grown by the laser heated pedestal growth technique. These fibers have orthorhombic symmetry with lattice parameters of a=5.773(1) Å, b=5.764(3) Å, c=8.157(2) Å at 300 K.     

Selective area growth of GaN microstructures on patterned (1 1 1) and (0 0 1) Si substrates

Selective MOVPE growth of GaN microstructure on silicon substrates has been investigated using SiO₂ mask having circular or stripe window. In case of (0 0 1)substrate, grooves with (1 1 1) facets at the sides were made by using the etching anisotropy of a KOH solution. On the (1 1 1) facets of patterned silicon substrate (or on the as opened window region of (1 1 1) substrate), growth of wurtzite GaN was performed, of which the c-axis is oriented along the 1 1 1 axis of silicon. The photoluminescence and X-ray diffraction analysis were performed to characterize the single crystal to reveal the effect of the growth conditions of the intermediated layer and the microstructure.     

Impedance spectroscopy analysis of AlGaN/GaN HFET structures

For HFET application a series of samples with 30 nm Al_xGa_1−xN (x=0.02–0.4) layers deposited at 1040°C onto optimised 2 μm thick undoped GaN buffers were fabricated. The Al_xGa_1−xN/GaN heterostructures were grown on c-plane sapphire in an atmospheric pressure, single wafer, vertical flow MOVPE system. Electrical properties of the Al_xGa_1−xN/GaN heterostructures and thick undoped GaN layers were evaluated by impedance spectroscopy method performed in the range of 80 Hz–10 MHz with an HP 4192A impedance meter using a mercury probe. The carrier concentration distribution through the layer thickness and the sheet carrier concentration were evaluated. A non-destructive, characterisation technique for verification of device heterostucture quality from the measured C–V and G–V versus frequency characteristics of the heterostructure is proposed.     

Growth and optical property characterization of textured barium titanate thin films for photonic applications

We have investigated the growth of barium titanate thin films on bulk crystalline and amorphous substrates utilizing biaxially oriented template layers. Ion beam-assisted deposition was used to grow thin, biaxially textured, magnesium oxide template layers on amorphous and silicon substrates. Growth of highly oriented barium titanate films on these template layers was achieved by molecular beam epitaxy using a layer-by-layer growth process. Barium titanate thin films were grown in molecular oxygen and in the presence of oxygen radicals produced by a 300 W radio frequency plasma. We used X-ray and in situ reflection high-energy electron diffraction (RHEED) to analyze the structural properties and show the predominantly c-oriented grains in the films. Variable angle spectroscopic ellipsometry was used to analyze and compare the optical properties of the thin films grown with and without oxygen plasma. We have shown that optical quality barium titanate thin films, which show bulk crystal-like properties, can be grown on any substrate through the use of biaxially oriented magnesium oxide template layers.     

The transition from As-doped GaN, showing blue emission, to GaNAs alloys in films grown by molecular beam epitaxy

We have studied the transition from As-doped GaN showing strong blue emission (2.6 eV) at room temperature to the formation of GaN_1−xAs_x alloys for films grown by plasma-assisted molecular beam epitaxy. We have demonstrated that with increasing N-to-Ga ratio there is first an increase in the intensity of blue emission at about 2.6 eV and then a transition to the growth of GaN_1−xAs_x alloy films. We present a model based on thermodynamic considerations, which can explain how this might occur.     

Comparative analysis of characteristics of Si, Mg, and undoped GaN

We have grown undoped, Si- and Mg-doped GaN epilayers using metalorganic chemical vapor deposition. The grown samples have electron Hall mobilities (carrier concentrations) of 798 cm²/V s (7×10¹⁶ cm⁻³) for undoped GaN and 287 cm²/V s (2.2×10¹⁸ cm⁻³) for Si-doped GaN. Mg-doped GaN shows a high hole concentration of 8×10¹⁷ cm⁻³ and a low resistivity of 0.8 Ω cm. When compared with undoped GaN, Si and Mg dopings increase the threading dislocation density in GaN films by one order and two orders, respectively. Besides, it was observed that the Mg doping causes an additional biaxial compressive stress of 0.095 GPa compared with both undoped and Si-doped GaN layers, which is due to the incorporation of large amount of Mg atoms (4–5×10¹⁹ cm⁻³).     

Effect of the N/Al ratio of AlN buffer on the crystal properties and stress state of GaN film grown on Si(1 1 1) substrate

The effect of the N/Al ratio of AlN buffers on the optical and crystal quality of GaN films, grown by metalorganic chemical vapor deposition on Si(1 1 1) substrates, has been investigated. By optimizing the N/Al ratio during the AlN buffer, the threading dislocation density and the tensile stress have been decreased. High-resolution X-ray diffraction exhibited a (0 0 0 2) full-width at half-maximum as low as 396 acrsec. The variations of the tensile stress existing in the GaN films were approved by the redshifts of the donor bound exiton peaks in the low-temperature photoluminescence measurement at 77 K.     

Epitaxial growth of the CoFe2O4 film on SrTiO3 and its characterization

Cobalt ferrite (CoFe₂O₄) thin film is epitaxially grown on (0 0 1) SrTiO₃ (STO) by laser molecular beam epitaxy (LMBE). The growth modes of CoFe₂O₄ (CFO) film are found to be sensitive to laser repetition, the transitions from layer-by-layer mode to Stranski–Krastanov (SK) mode and then to island mode occur at the laser repetition of 3 and 5 Hz at 700 °C, respectively. The X-ray diffraction (XRD) results show that the CFO film on (0 0 1) SrTiO₃ is compressively strained by the underlying substrate and exhibits high crystallinity with a full-width at half-maximum of 0.86°. Microstructural studies indicate that the as-deposited CFO film is c-oriented island structure with rough surface morphology and the magnetic measurements reveal that the compressive strained CoFe₂O₄ film exhibits an enhanced out-of-plane magnetization (190 emu/cm³) with a large coercivity (3.8 kOe).     

Correlation between interfacial structure and c-axis-orientation of LiNbO3 films grown on Si and SiO2 by electron cyclotron resonance plasma sputtering

Thin films of crystalline lithium niobate (LN) grown on Si(1 0 0) and SiO₂ substrates by electron cyclotron resonance plasma sputtering exhibit distinct interfacial structures that strongly affect the orientation of respective films. Growth at 460–600 °C on the Si(1 0 0) surface produced columnar domains of LiNbO₃ with well-oriented c-axes, i.e., normal to the surface. When the SiO₂ substrate was similarly exposed to plasma at temperatures above 500 °C, however, increased diffusion of Li and Nb atoms into the SiO₂ film was seen and this led to an LN–SiO₂ alloy interface in which crystal-axis orientations were randomized. This problem was solved by solid-phase crystallization of the deposited film of amorphous LN; the degree of c-axis orientation was then immune to the choice of substrate material.     

Growth and characterization of epitaxial layers on aluminum nitride substrates prepared from bulk, single crystals

A comparative study of epitaxy of AlN, GaN and their alloys, grown on c-axis and off-axis substrates of single-crystal aluminum nitride has been carried out. Growth on off-axis (>30°) substrates appears to result in rough surfaces and the absence of two-dimensional electron gas (2DEG). However, smooth morphologies were demonstrated for both homoepitaxial and heteroepitaxial growth on on-axis (<2°) substrates. On one of these oriented substrates a 2DEG, with a mobility of 1000 cm²/V s and a sheet density of 8.5×10¹² cm⁻² at room temperature, was also demonstrated for the first time.     

Low-temperature growth of GaN by atomic nitrogen based on a dielectric barrier discharge

GaN films were deposited on sapphire(0 0 0 1) and Si(1 0 0) substrates by MOCVD using an atomic nitrogen source based on a dielectric barrier discharge (DBD) method. Molecule nitrogen and trimethylgallium (TMG) were separately delivered to the substrates. Wurtzite GaN films, with no trace of cubic GaN, were successfully grown on -Al₂O₃ substrates even at relatively low temperatures (<800°C). Sapphire substrate RMS roughness was 5.01 and 4.93 Å before and after the exposure to DBD N-source, respectively. This shows negligible irradiation damage of accelerated N₂⁺ ion as well as the effect of smoothening the substrate surfaces with DBD N-source. The PL results exhibited small luminescence at the spectral region of blue and UV but a luminescence around the yellow region (2.5 eV) was detected. This is caused by oxygen impurity from AES analysis.     

Defect reduction in GaN epilayers and HFET structures grown on (0 0 0 1)sapphire by ammonia MBE

The quality of GaN epilayers grown by molecular beam epitaxy on substrates such as sapphire and silicon carbide has improved considerably over the past few years and in fact now produces AlGaN/GaN HEMT devices with characteristics among the best reported for any growth technique. However, only recently has the bulk defect density of MBE grown GaN achieved levels comparable to that obtained by MOVPE and with a comparable level of electrical performance. In this paper, we report the ammonia-MBE growth of GaN epilayers and HFET structures on (0 0 0 1)sapphire. The effect of growth temperature on the defect density of single GaN layers and the effect of an insulating carbon doped layer on the defect density of an overgrown channel layer in the HFET structures is reported. The quality of the epilayers has been studied using Hall effect and the defect density using TEM, SEM and wet etching. The growth of an insulating carbon-doped buffer layer followed by an undoped GaN channel layer results in a defect density in the channel layer of 2×10⁸ cm⁻². Mobilities close to 490 cm²/Vs at a carrier density of 8×10¹⁶ cm⁻³ for a 0.4 μm thick channel layer has been observed. Growth temperature is one of the most critical parameters for achieving this low defect density both in the bulk layers and the FET structures. Photo-chemical wet etching has been used to reveal the defect structure in these layers.     

Homoepitaxial growth and electrical characterization of GaN-based Schottky and light-emitting diodes

Homoepitaxial growth of GaN epilayers on free-standing hydride vapor phase epitaxy (HVPE) GaN substrates offered a better control over surface morphology, defect density, and doping concentration compared to conventional heteroepitaxial growth. The FWHM of the (0 0 0 2) X-ray diffraction (XRD) rocking curve from homoepitaxial GaN was measured to be as low as 79 arcsec, much smaller than 230 arcsec for GaN grown on sapphire. Schottky diodes grown on GaN substrates exhibited sharper breakdown characteristics and much lower reverse leakage than diodes on sapphire. However, the homoepitaxial devices had poor scalability due to the presence of yield-killing defects originating from the substrate surface. Vertical InGaN/GaN light-emitting diodes (LEDs) on GaN substrates showed reduced series resistance and reverse leakage compared to lateral LEDs on sapphire. Wafer mapping demonstrated that the distribution of leaky homoepitaxial devices correlated well with that of macroscopic defects in the GaN substrates.     

Growth of GaN films on PLD-deposited TaC substrates

GaN films were grown by metal organic chemical vapor deposition on TaC substrates that were created by pulsed laser deposition of TaC onto (0 0 0 1) SiC substrates at ∼1000 °C. This was done to determine if good quality TaC films could be grown, and if good quality GaN films could be grown on this closely lattice matched to GaN, conductive material. This was done by depositing the TaC on on-axis and 3° or 8° off-axis (0 0 0 1) SiC at temperatures ranging from 950 to 1200 °C, and examining them using X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. The GaN films were grown on as-deposited TaC films, and films annealed at 1200, 1400, or 1600 °C, and examined using the same techniques. The TaC films were polycrystalline with a slight (1 1 1) texture, and the grains were ∼200 nm in diameter. Films grown on-axis were found to be of higher quality than those grown on off-axis substrates, but the latter could be improved to a comparable quality by annealing them at 1200–1600 °C for 30 min. TaC films deposited at temperatures above 1000 °C were found to react with the SiC. GaN films could be deposited onto the TaC when the surface was nitrided with NH₃ for 3 min at 1100 °C and the low temperature buffer layer was AlN. However, the GaN did not nucleate easily on the TaC film, and the crystallites did not have the desired (0 0 0 1) preferred orientation. They were ∼10 times larger than those typically seen in films grown on SiC or sapphire. Also the etch pit concentration in the GaN films grown on the TaC was more than 2 orders of magnitude less than it was for growth on the SiC.     

High-resolution XRD study of stress-modulated YBCO films with various thicknesses

High-quality epitaxial YBa₂Cu₃O_7−δ (YBCO) superconducting films with thicknesses between 0.2 and 2 μm were fabricated on (0 0 l) LaAlO₃ with direct-current sputtering method. The influence of film thickness on the structure and texture was investigated by X-ray diffraction conventional θ–2θ scan and high-resolution reciprocal space mapping (HR-RSM). The films grew with strictly c-axis epitaxial, and no a-axis-oriented growth was observed up to a thickness of 2 μm. Lattice parameters of the YBCO films with different thicknesses were extracted from symmetry and asymmetry HR-RSMs. The X-ray lattice parameter method was used to determine the residual stress in YBCO films by measuring the a-, b-, c-axis strains, respectively. The results showed that YBCO films within thinner than 1 μm were under compressive stress, which was relieved increasing of film thickness. However, beyond 1 μm in thickness, YBCO films exhibited a tensile stress. Based on the experimental analysis, the variety of residual stresses in the films is mainly attributed to oxygen vacancies with thickness of YBCO film increasing.     

InGaN/GaN微米阵列结构的生长及发光性能研究

采用金属有机化学气相外延技术,在图形化蓝宝石衬底上通过选区外延可控生长了三种不同形貌的InGaN/GaN微米阵列结构,阵列尺寸均为6μm.其中,六方片状阵列结构以(0001)c面为主,高度为0.6μm;六棱台状阵列结构包括一个(0001)c面和六个等效的(10-11)半极性面,高度为1.2μm;六棱锥状阵列结构以(10...     

The influences of supersaturation on LPE growth of GaN single crystals using the Na flux method

The dependency of LPE growth rate and dislocation density on supersaturation in the growth of GaN single crystals in the Na flux was investigated. When the growth rate was low during the growth of GaN at a small value of supersaturation, the dislocation density was much lower compared with that of a substrate grown by the Metal Organic Chemical Vapor Deposition method (MOCVD). In contrast, when the growth rate of GaN was high at a large value of supersaturation, the crystal was hopper including a large number of dislocations. The relationship between the growth conditions and the crystal color in GaN single crystals grown in Na flux was also investigated. When at 800 °C the nitrogen concentration in Na–Ga melt was low, the grown crystals were always tinted black. When the nitrogen concentration at 850 °C was high, transparent crystals could be grown.