Photocatalytic properties of mesoporous TiO<Subscript>2</Subscript>/ZrO<Subscript>2</Subscript> films in gas-phase oxidation of alcohols

We have used the sol-gel template synthesis method to obtain mesoporous zirconium-containing titanium dioxide films and have studied their structural and sorption characteristics, surface acid function, and photocatalytic activity during gas-phase oxidation of aliphatic alcohols. We have shown that the zirconium content changes the acidity and specific surface area of the films, determining the rate at which the studied processes occur and the relative yield of reaction products. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 41, No. 6, pp. 354–359, November–December, 2005.     

Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Electrical conductivity studies in the system Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript>-Li<Subscript>1.33</Subscript>Ti<Subscript>1.67</Subscript>O<Subscript>4</Subscript>

Electrical conductivity in the monoclinic Li₂TiO₃, cubic Li_1.33Ti_1.67O₄, and in their mixture has been studied by impedance spectroscopy in the temperature range 20–730 °C. Li₂TiO₃ shows low lithium ion conductivity, σ₃₀₀≈10^–6 S/cm at 300 °C, whereas Li_1.33Ti_1.67O₄ has 3×10^–8 at 20 °C and 3×10^–4 S/cm at 300 °C. Structural properties are used to discuss the observed conductivity features. The conductivity dependences on temperature in the coordinates of 1000/T versus log_e(σT) are not linear, as the conductivity mechanism changes. Extrinsic and intrinsic conductivity regions are observed. The change in the conductivity mechanism in Li₂TiO₃ at around 500–600 °C is observed and considered as an effect of the first-order phase transition, not reported before. Formation of solid solutions of Li_{2– x} Ti_{1+ x} O₃ above 900 °C significantly increases the conductivity. Irradiation by high-energy (5 MeV) electrons causes defects and the conductivity in Li₂TiO₃ increases exponentially. A dose of 144 MGy yields an increase in conductivity of about 100 times at room temperature. Electronic Publication     

Charge distribution and mobility of lithium ions in Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> from <Superscript>6,7</Superscript>Li NMR data

A comparative analysis of ^6,7Li NMR spectra is performed for the samples of monoclinic lithium titanate obtained at different synthesis temperatures. In the ⁷Li NMR spectra three lines are found, which differ in quadrupole splitting frequencies v _Q and according to ab initio EFG calculations are assigned to three crystallographic sites of lithium: Li1 (v _Q ～ 27 kHz); Li2 (v _Q ～ 59 kHz); Li3 (v _Q ～ 6 kHz). The dynamics of lithium ions is studied in a wide temperature range from 300 K to 900 K. It is found that the narrowing of ⁷Li NMR spectra as a result of thermally activated diffusion of lithium ions in the low-temperature Li₂TiO₃ sample is observed at a higher temperature in comparison with a sample of high-temperature lithium titanate. Based on the analysis of ⁶Li NMR spectra it is assumed that there is mixed occupancy of lithium and titanium sites in the corresponding layers of the crystal structure of low-temperature lithium titanate, which hinders lithium ion transfer over regular crystallographic sites.     

Selective catalytic oxidation of ammonia into nitrogen and water vapour over transition metals modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, TiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>

Copper or iron supported on commercially available oxides, such as γ-Al₂O₃, TiO₂ (anatase) and monoclinic tetragonal ZrO₂ (mt-ZrO₂) were tested as catalysts for selective catalytic oxidation of ammonia into nitrogen and water vapour (NH₃-SCO) in the low temperature range. Different commercial oxides were used in this study to determine the influence of the specific surface area, acidic nature of the support and crystalline phases as well as of the type of species and aggregation state of transition metals on the catalytic performance in selective ammonia oxidation. Copper modified oxide supports were found to be more active and selective to nitrogen than catalysts impregnated with iron. Activities of both transition metal modified samples decreased in the following order: mt-ZrO₂, TiO₂ (anatase), γ-Al₂O₃. Quantitative total ammonia conversion was achieved with the Cu/ZrO₂ catalytic system at 400°C. Characterisation techniques, e.g. H₂-temperature programmed reduction, UV-VIS-diffuse reflectance spectroscopy, suggest that easily reducible copper oxide species are important in achieving high catalytic performances at low temperatures.     

Oxygen redistribution in ZrO<Subscript>2</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript> system

This work represents the results of oxygen redistribution studies at quantitative and isotopic levels in synthesis and thermal treatment of ZrO - (0 to 35 mol %) Y₂O₃ solid solution crystals. The crystals were grown by directed melt crystallization method in a cold container using direct high-frequency heating. The crystal oxygen content and isotopic composition data was collected with respect to stabilizer concentration and technological conditions of synthesis. The temperature and frequency relationships of crystal electroconductivity were also studied. Some strength and tribological characteristics of the given materials were represented. The solid state formation by directional melt crystallization was shown to involve oxygen isotopic exchange interaction between the melt, growing crystal, and gas phase.     

TiO<Subscript>2</Subscript> nanofibers embedding single crystalline TiO<Subscript>2</Subscript> nanowires

Epitaxially grown titanium dioxide (TiO₂) nanofibers embedding single crystalline TiO₂ nanowires (NWs) were successfully fabricated by electropinning poly(vinyl pyrrolidone)/ethanol solutions mixed with hydrothermally synthesized TiO₂ NWs and titanium isopropoxide precursors and subsequently calcinating the electrospun nanofibers. Utilizing scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the morphologies of TiO₂ NWs and nanofibers were investigated. High resolution TEM (HR-TEM) and selected area electron diffraction (SAED) allowed us to indentify the fact that, during the calcination process under the optimized condition, titanium isopropoxide precursors were epitaxially crystallized on the surface of single crystalline TiO₂ NWs. Based on the X-ray diffraction (XRD) experiments, it was also realized that the crystalline structure of hydrothermally synthesized TiO₂ NWs and epitaxially crystallized TiO₂ nanofibers is anatase and that TiO₂ composite nanofibers embedding TiO₂ NWs exhibited a higher crystallinity than the pristine TiO₂ nanofibers. Additionally, ultraviolet visible (UV–Vis) spectra of nanofibers indicated that optical properties of TiO₂ nanofibers can be tuned by introducing the single crystalline TiO₂ NWs.     

Synthesis and characterization of ZrO<Subscript>2</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanofilms

Processes involved in the preparation of zirconia and yttria thin films by sol-gel technology from film-forming solutions (FFSs) were studied over the entire range of concentrations. The physicochemical properties, composition, and structure of the films were studied.     

Phase equilibria in the system Li<Subscript>2</Subscript>O-MgO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>

The subsolidus region of the Li₂O-MgO-B₂O₃ system has been studied by X-ray powder diffraction and differential thermal analysis. Isothermal sections at 500–550 and 650–700°C have been designed. The following complex borates have been found to form: at 500–550°C, Li₂MgB₂O₅ and LiMgBO₃ are formed; at 650–700°C, a new phase Li₄MgB₂O₅ is formed along with LiMgBO₃; and at 5500–600°, Li₂MgB₂O₅ is formed.     

Influence of ZrO<Subscript>2</Subscript> on the physicochemical properties of the ZrO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> binary system

A series of ZrO₂-TiO₂ mixed oxides with different weight ratios (5, 20, and 30% ZrO₂) were prepared by wet impregnation of TiO₂-P25 Degussa with certain amounts of ZrO(NO₃)₂·6H₂O (Fluka) dissolved in deionised water. The samples were characterized by the XRD, , , , and BET methods. An increase in ZrO₂ content shifted the phase transition temperature (anatase into rutile) toward higher temperatures. X-ray diffraction using an Anton Paar XRK900 reactor chamber indicated that, in the case of samples containing ZrO₂, an additional diffraction peak appeared after cooling down to 25°C. This peak could be attributed to a polymorph of TiO₂ such as in the single crystal of anatase or hexagonal form of TiO₂ which appears in the presence of ZrO₂. Generally, the preparation of dioxide systems can modify the properties of pure compounds or generate new catalytic sites as a result of strong interaction between ZrO₂ and TiO₂ oxides. The binary systems exhibit advantages like strong acidity, extended specific surface area, and high thermal stability in comparison with TiO₂. The article is published in the original.     

Yttria stabilized zirconia solid electrolyte surface modification with ZrO<Subscript>2</Subscript>, Y<Subscript>2</Subscript>O<Subscript>3</Subscript>, and ZrO<Subscript>2</Subscript> + 9 mol % Y<Subscript>2</Subscript>O<Subscript>3</Subscript> films

The surface of ceramic electrolyte ZrO₂ + 9 mol % Y₂O₃, hereinafter referred to as YSZ (abbreviated yttria stabilized zirconia), was modified with 0.1 to 0.2 μm oxide films of ZrO₂, Y₂O₃, and YSZ (same composition as substrate) by dip coating in alcohol solutions of the relevant salts and further annealing. The results of scanning electronic microscopy and X-ray diffraction evidence epitaxial film growth. By means of impedance spectroscopy at the temperatures of 500 to 600°C, the effect of YZS electrolyte surface modification with ZrO₂, Y₂O₃, and YSZ films to the polarization resistance of silver electrode was studied.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Photooxidation of Ethylbenzene with TiO<Subscript>2</Subscript> and Metal Coated TiO<Subscript>2</Subscript> and its Kinetics

Summary. Photooxidation of ethylbenzene with oxygen to give ethylbenzene hydroperoxide has been achieved in a stirred photochemical reactor that was cooled by a water system by irradiation with a 400W high-pressure mercury lamp and using TiO₂ powder and metal coated TiO₂. The effects of the amount of copper or silver coated on TiO₂ and of the temperature on the rate of oxidation have been investigated. It is suggested that thermal cleavage of the O–O bond and photochemically generated singlet oxygen should be considered as the initiating step in a radical chain mechanism. An optimum loading of 6% Ag or 4–5% Cu was observed for photooxidation of ethylbenzene.     

Interactions in the Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript>-Ti<Subscript>2</Subscript>O<Subscript>3</Subscript> System

Interactions in the Al₂TiO₅-Ti₂O₃ system were studied and the regions of existence of Al_2?2xTi _2x ³⁺ Ti⁴⁺O₅ solid solutions with a pseudobrookite structure were determined.     

Oxygen redistribution during crystal growth of ZrO<Subscript>2</Subscript>-R<Subscript>2</Subscript>O<Subscript>3</Subscript> solid solutions

This paper presents the results of our experimental studies of quantitative redistribution and isotope fractionation of oxygen during the crystal growth of cubic solid solutions based on ZrO₂. The single crystals were grown by directional crystallization of a melt in a cold container. As stabilizing oxides, we used Y₂O₃, Gd₂O₃, and Yb₂O₃ in concentrations of 8–40 mol %. The results showed that the oxygen isotopic growth effects changed depending on the type and content of the stabilizer in the crystals of ZrO₂-R₂O₃ solid solutions.     

Hydrothermal synthesis of nanosized and amorphous alumina in the ZrO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-H<Subscript>2</Subscript>O system

The reciprocal influence of components on the chemical and structural transformations in the ZrO₂-Al₂O₃-H₂O system during nanoparticle formation under hydrothermal conditions is considered. The possibility of formation of amorphous aluminum oxide under hydrothermal conditions is found as a result of the influence of zirconia nanoparticles on the crystallization.     

Binary ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> xerogels: Synthesis and properties

Binary systems of silica and zirconia xerogels have been prepared by hydrolysis of zirconium(IV) oxychloride in the silica gel matrix. Systems of various composition have been studied by ¹H NMR, IR spectroscopy, and thermogravimetry and have been tested in a model process of hydrogen peroxide decomposition. It has been shown that the physicochemical properties of binary oxide systems can be tailored by varying the component ratio.     

Glass formation in the Li<Subscript>2</Subscript>O-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>-TeO<Subscript>2</Subscript> system

In the Li₂O-Ta₂O₅-TeO₂ system, the boundaries of the glass region have been determined. The electrical and spectral properties of glasses and crystalline materials have been investigated.