HILL屈服准则与晶体塑性模型对FCC单晶材料塑性各向异性描述能力的比较

采用宏观HILL模型和晶体塑性模型对面心立方单晶(FCC)材料的非均匀交形进行了数值模拟，意在比较两种不同尺度的模型对塑性各向异性的描述能力的差异。为了使两种模型具有可比性，对于FCC单晶材科，本文提出一种用晶体塑性模型来确定HILL模型中各向异性参数的标定方法。数值分析表明，两类模型对单晶体塑性各向异性的描述能力存在着差异。对FCC单晶材料，HILL模型对各向异性的预测能力没有晶体塑性模型细致，晶体塑性模型更能追踪塑性各向异性的变化。但两种模型对应力应变响应预测的趋势是一致的。对两种模型描述的差异，做了详细的分析。     

考虑应力梯度效应的金属微梁屈服模型研究

一系列微加载测试结果表明,金属微梁的弯曲强度会随着材料外部几何特征尺寸的减小而显著升高,呈现出明显的尺寸相关性.基于位错塞积模型,探讨了纯金属单晶微梁的初始屈服应力,并提出了描述其尺寸相关性行为的关键内禀特征长度.通过综合分析现有的微梁弯曲实验及其离散位错动力学数值模拟结果,并考虑到位错-自由表面交互作用的影响,提出了一种仅涉及位错源的位错塞积构型.在此构型下,对线性应力梯度作用下的位错塞积行为进行了连续性分析,并建立了一个由位错源主导的应力梯度屈服模型.该模型有效地解释了微梁初始屈服应力的尺寸相关性,并与实验结果一致.研究结果表明,针对外部几何特征尺寸在数微米及以下的纯金属单晶微梁,位错塞积行为是其尺寸相关性行为的主导机制,而且刻画这种行为需要两个内禀特征长度参数,即位错源长度和位错塞积长度.为解释非均匀加载条件下微尺度晶体材料屈服应力的尺寸相关性行为,特别是纯金属单晶微梁,提供了新的视角.     

计入膜力塑性耗散效应的矩形板塑性动力响应

从能量的观点在小挠度理论中引入表征膜力塑性耗散效应的修正因子,基于刚性板块的总体平衡给出矩形板大挠度塑性动力响应的完全运动方程组,分析了理想刚塑性简支和固支矩形板在矩形脉冲和冲击载荷下包括移行塑性铰相的完全大挠度响应过程。解决了当矩形板的挠度达到厚度量级时弯矩、膜力的联合作用问题,理论预报的结果在板的挠度为10倍板厚的量级与实验结果符合良好,改进了只考虑弯矩作用的小挠度理论结果和模态近似估计。     

纳米金属丝拉伸破坏及其应变率效应

建立了适于研究纳米金属快速变形破坏过程的分子动力学模型,并对不同应变率工况下不同截面尺寸单晶镍纳米丝的零温单向拉伸破坏过程进行了分子动力学模拟.模拟得到各种纳米镍丝的应力-应变曲线、屈服应变、屈服强度、断裂强度和初始弹性模量,提出了纳米金属丝快速变形力学性能的应变率效应预测公式并加以验证.计算表明金属纳米丝的屈服应变与尺寸和应变率无关,屈服强度、断裂强度和弹性模量与应变率呈对数关系.     

描述大应变率范围下材料响应的粘塑性本构模型

以位错动力学理论中的Ｏｒｗａｎ和Ｇｉｌｍａｎ关系为基础建立描述率相关材料非弹性响应的基本方程，选择材料准静态实验的单轴响应作为强化演化的规律，并考虑应变率敏感程度随变形产生变化的特性，建立了适用于大应变率范围内率相关材料的统一型粘塑性本构模型。对铝１１００－０在应变率范围１０－５～１０４ｓ－１内产生的有限塑性应变的单轴响应进行了理论预测，与Ｋｈａｎ和Ｈｕａｎｇ［１］的实验数据及模型预测结果进行了比较，结果表明本文模型具有较高的预测精度，在高应变率和较大应变下不容忽视率敏感参数随变形的变化。     

泡沫材料的应变率效应

对泡沫材料的应变率敏感性进行了系统深入的讨论,认定这种材料是应变率敏感材料,这种敏感性主要是由于泡孔的变形特性产生的。泡沫材料变形的局部化、微观惯性和致密性导致压垮应力明显提高,基体的应变率效应及泡孔的形状大小并不能对泡沫材料应变率敏感性起主导作用。     

结构塑性动力响应当前的研究进展和重点

本文从结构塑性动力响应的工程背景和研究特点出发,简要介绍了此学科当前的研究进展和重点。主要评述了国内外学者所关注的一些基本理论问题和研究方法。同时也提出了数值分析和近似方法中尚待解决的问题。     

高应变率下铁锰铸造合金正向和反向应变率效应的研究

对两种铁锰铸造合金在准静态和冲击动态下进行了宏观与微观相结合的试验研究。实验结果表明 ,在准静态下 ,铁锰铝硅合金的强度高于铁锰铝合金 ,但在高应变率动态加载下 ,铁锰铝合金的强度反而高于铁锰铝硅合金。铁锰铝合金表现出很强的应变率强化效应 (正向应变率效应 ) ,而铁锰铝硅合金表现出应变率无关或应变率弱化效应 (反向应变率效应 )。随着应变率的进一步提高 ,两者又都存在一定程度的应变率弱化倾向。根据这一现象 ,着重对高应变率下的绝热温升所致热软化、内部损伤的率相关演化、以及应力诱变马氏体相变等方面进行了探讨。     

损伤引起的反向应变率效应及其对本构关系和热粘塑性失稳的影响

对于材料在高应变率下的应变率无关和应变率负敏感现象,本文根据铸镁合金的宏观与微观相结合的试验结果,提出了一个基于损伤弱化的反向应变率效应机制,并建议了一个计及这一反向效应的热粘塑性本构方程。由此可以解释材料的表观应变率强化、表观应变率无关和表观应变率弱化三类基本情况。相应地,随损伤引起的反向应变率效应的增强,热粘塑性失稳也有三种基本情况:或在更高应变率或更大应变下发生绝热剪切,或由临界准则转化为临界应变准则,以及或在高应变率下不会发生绝热剪切。     

脉冲载荷作用下钢梁动力响应及反常行为的应变率效应

为了讨论率敏感材料软钢钢梁受矩形脉冲载荷作用下的动力响应问题,通过直接离散有限变形弹塑性连续体最小加速度原理中的Lee泛函得到基本控制方程,并将包含应变率的Cowper-Symonds方程嵌入应力-应变关系方程,使该计算模型计及材料的应变率效应,因而能够准确描述钢梁受爆炸和冲击载荷作用下的动力响应问题。该计算模型的有效性通过与通用有限元程序ABAQUS比较而得到了验证,并进一步与已有的刚塑性解做了对比。利用该计算模型进行数值计算,分析了均布和集中脉冲载荷作用下钢梁动力响应的应变率效应,结果发现对于钢梁存在新的异常行为响应模式,应变率导致异常区域偏移和扩大,已有的刚塑性解在一定载荷强度范围内不能准确预报钢梁的实际位移。     

The void-size effect on plastic flow localization in the Gurson model

Recent studies have shown that the size of microvoids has a significant effect on the void growth rate. The purpose of this paper is to explore whether the void size effect can influence the plastic flow localization in ductile materials. We have used the extended Gurson‘s dilatational plasticity theory, which accounts for the void size effect, to study the plastic flow localization in porous solids with long cylindrical voids. The localization model of Rice is adopted, in which the material inside the band may display a different response from that outside the band at the incipient plastic flow localization. The present study shows that it has little effect on the shear band angle.     

Optical measurement of the specimen deformation at high strain rate

During recent years, the investigation of the strain-rate-dependent properties of materials has become more and more important. The experimental techniques used to establish the specific dynamic behavior of materials all have in common that the acquisition of information concerning the deformation of the specimen is cumbersone and often questionable. Mostly, only limited information on the spatial distribution and time evolution of the deformation in specimen can be obtained. In this paper, a non-contact, optical technique is presented, providing the time evolution and spatial distribution of the axial deformation in specimens during a high strain rate test. The deformation of a line grid attached to the specimen is recorded during an experiment by means of a rotating drum camera. The time history of the axial displacements is subsequently derived by an advanced technique based on digital geometric moiré combined with a phase-shift method, specially developed to this purpose. The technique can be applied to a wide range of materials and high strain rate tests, and is illustrated by means of a split Hopkinson tensile bar experiment on a steel sheet specimen.     

Combined grain size, strain rate and loading condition effects on mechanical behavior of nanocrystalline Cu under high strain rates

Molecular dynamics simulations of nanocrys-talline Cu with average grain sizes of 3.1 nm, 6.2 nm, 12.4 nm and 18.6 nm under uniaxial strain and stress tension at strain rates of 10 8 s 1 , 10 9 s 1 and 10 10 s 1 are performed to study the combined grain size, strain rate and loading condition effects on mechanical properties. It is found that the strength of nanocrystalline Cu increases as grain size increases regardless of loading condition. Both the strength and ductility of nanocrystalline Cu increase with strain rate except that there is no monotonic relation between the strength and strain rate for specimens under uniaxial strain loading. Moreover, the strength and ductility of specimens under uniaxial strain loading are lower than those under uniaxial stress loading. The nucleation of voids at grain boundaries and their subsequent growth characterize the failure of specimens under uniaxial strain loading, while grain boundary sliding and necking dominate the failure of specimens under uniaxial stress loading. The rate dependent strength is mainly caused by the dynamic wave effect that limits dislocation motion, while combined twinning and slipping mechanism makes the material more ductile at higher strain rates.     

Parameter identification of advanced plastic strain rate potentials and impact on plastic anisotropy prediction

In the work presented in this paper, several strain rate potentials are examined in order to analyze their ability to model the initial stress and strain anisotropy of several orthotropic sheet materials. Classical quadratic and more advanced non-quadratic strain rate potentials are investigated in the case of FCC and BCC polycrystals. Different identifications procedures are proposed, which are taking into account the crystallographic texture and/or a set of mechanical test data in the determination of the material parameters.     

An analysis of key characteristics of the Frank-Read source process in FCC metals

A well-known intragranular dislocation source, the Frank-Read (FR) source plays an important role in size-dependent dislocation multiplication in crystalline materials. Despite a number of studies in this topic, a systematic investigation of multiple aspects of the FR source in different materials is lacking. In this paper, we employ large scale quasistatic concurrent atomistic-continuum (CAC) simulations to model an edge dislocation bowing out from an FR source in Cu, Ni, and Al. First, a number of quantities that are important for the FR source process are quantified in the coarse-grained domain. Then, two key characteristics of the FR source, including the critical shear stress and critical dislocation configuration, are investigated. In all crystalline materials, the critical stresses and the aspect ratio of the dislocation half-loop height to the FR source length scale well with respect to the FR source length. In Al, the critical stress calculated by CAC simulations for a given FR source length agrees reasonably well with a continuum model that explicitly includes the dislocation core energy. Nevertheless, the predictions of the isotropic elastic theory do not accurately capture the FR source responses in Cu and Ni, which have a relatively large stacking fault width and elastic anisotropy. Our results highlight the significance of directly simulating the FR source activities using fully 3D models and shed light on developing more accurate continuum models.     

SHPB系统试件恒应变率加载实验方法研究

为了获得材料准确的动态力学性能参数,提出了两种对试件实现恒应变率加载的实验方法:双试件SHPB方法和将圆柱形子弹改变成柱锥形子弹的SHPB方法。对三种金属材料进行了实验,并用数值模拟的手段对这两种方法进行了验证和比较。     

A simplified over-stress analytical model of the dynamic buckling of a perfectly plastic column under axial impact

I.Introduction-Tllet1niaxiaIyieldingstrengthofastrain-raterelativemateriaIvariesobviuoslyunderdynamicloadstll.Sotheslrain-rateeffectshou1dbeincludedintheanalysisofplasticdynamicbucklingofacolumnl:J.ThispaperappliesMalvern'sover-stressmodell3jtoperfectplasticn'aterialsinthepIasticdynamicbucklinganalysisofacolumn.ThedifferentialequationofdynaI11icsaboutthenexuraIdeflectionofthecolumnisdeduced.Thedominantbucklingmode.thecriticalloadandthebucklingtimeissolvedviatheamplifyingfunctionmethodl4l.F…     

高应力岩体爆破卸荷过程中应变率及应变能特征

针对高应力岩体爆破开挖卸载问题,自制了一台轴向加、卸载实验测试平台,通过实验测试获得了爆破卸荷过程中岩杆的动态应变及应变率数据。实测数据表明：开挖面附近岩体的爆破加、卸载以及初始应力卸载应变率均在10⁻¹ s⁻¹量级以上,验证了高地应力区岩体爆破开挖卸荷是一动态过程。建立了初始应力卸载一维力学模型,揭示了卸载波的传播机制;通过分析爆破卸荷过程应变能密度的时空分布特征,建立了应变能密度与各阶段应变率变化规律的联系。结合实测数据,采用隐式-显式顺序求解方法,进一步分析了高应力区岩体爆破卸荷荷载各阶段应变率沿岩杆的变化规律。结果表明：爆破加载阶段的平均应变率沿杆件逐渐衰减,且衰减速度逐渐减小;爆破卸阶段平均应变率沿杆件也呈衰减趋势;而初始应力的应变能稳定释放,其平均应变率无衰减趋势。

     

Anisotropic plastic stress field at a mixed-mode crack tip under plane and anti-plane strain

On condition that any perfectly plastic stress component at a crack tip is nothingbut the function ofθ.by making use of equilibrium equations,anisotropic plastic stress-strain-rate relations,compatibility equations and Hill anisotropic plastic yieldcondition,in the present paper,we derive the generally analytical expressions of theanisotropic plastic stress field at a mixed-mode crack tip under plane and anti-planestrain.Applying these generally analytical expressions to the mixed-mode cracks,wecan obtain the analytical expressions of anisotropic plastic stress fields at the tips ofmixed-modeⅠ-Ⅲ,Ⅱ-ⅢandⅠ-Ⅱ-Ⅲcracks.