CVD graphene vs. highly ordered pyrolytic graphite for use in electroanalytical sensing

We explore and contrast the electroanalytical performance of a commercially available CVD grown graphene electrode with that of edge- and basal-plane pyrolytic graphite electrodes constructed from highly ordered pyrolytic graphite for the sensing of biologically important analytes, namely β-nicotinamide adenine dinucleotide (NADH) and uric acid (UA). We demonstrate that for the analytes studied here, in the best case, the electroanalytical performance of the CVD-graphene mimics that of edge plane pyrolytic graphite, suggesting no significant advantage of utilising CVD-graphene in this context.     

Direct Oxidation of Ascorbic Acid at an Edge Plane Pyrolytic Graphite Electrode: A Comparison of the Electroanalytical Response with Other Carbon Electrodes

The direct electrochemical oxidation of ascorbic acid at an edge plane pyrolytic graphite electrode (EPPG) is investigated and compared with other common carbon‐based electrodes, specifically glassy carbon, boron doped diamond and basal plane pyrolytic graphite. It is found that the EPPG electrode shows a significantly higher degree of electrochemical reversibility than the other electrode substrates giving rise to an analytically optimized limit of detection and sensitivity of 7.1×10^?5 M and 0.065 A M^?1 respectively.     

The electrochemical performance of graphene modified electrodes: an analytical perspective

We explore the use of graphene modified electrodes towards the electroanalytical sensing of various analytes, namely dopamine hydrochloride, uric acid, acetaminophen and p-benzoquinone via cyclic voltammetry. In line with literature methodologies and to investigate the full-implications of employing graphene in this electrochemical context, we modify electrode substrates that exhibit either fast or slow electron transfer kinetics (edge- or basal- plane pyrolytic graphite electrodes respectively) with well characterised commercially available graphene that has not been chemically treated, is free from surfactants and as a result of its fabrication has an extremely low oxygen content, allowing the true electroanalytical applicability of graphene to be properly de-convoluted and determined. In comparison to the unmodified underlying electrode substrates (constructed from graphite), we find that graphene exhibits a reduced analytical performance in terms of sensitivity, linearity and observed detection limits towards each of the various analytes studied within. Owing to graphene's structural composition, low proportion of edge plane sites and consequent slow heterogeneous electron transfer rates, there appears to be no advantages, for the analytes studied here, of employing graphene in this electroanalytical context.     

Cyclic Voltammograms of Ferrocene on Multi‐Walled Carbon Nanotubes (MWCNTs)‐Modified Edge Plane Pyrolytic Graphite (EPPG) Electrode in Room Temperature Ionic Liquids (RTILs) of 1‐Ethyl‐3‐Methylimidazolium Tetrafluoroborate (EMIBF4)

In this work, the electrochemical behavior of ferrocene (Fc) was investigated by cyclic voltammetry (CV) in room temperature ionic liquids (RTILs) of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) on glass carbon (GC), edge plane pyrolytic graphite (EPPG) and multi‐walled carbon nanotube (MWCNTs)‐modified EPPG electrodes, respectively. The results demonstrated that on GC electrode, pairs of well‐defined reversible peaks were observed, while for the electrode of EPPG, the peak potential separation (ΔE_p) is obviously larger than the theoretical value of 59 mV, hinting that the electrode of EPPG is distinguished from the commonly used electrode, consistent with the previous proposition that EPPG has many “defects”. To obtain an improved electrochemical response, multi‐walled carbon nanotubes (MWCNTs) were modified on the electrode of EPPG; the increased peak current and promoted peak potential separation not only proved the existence of “defects” in MWCNTs, but also supported that “creating active points” on an electrode is the main contribution of MWCNTs. Initiating the electrochemical research of Fc on the MWCNTs‐modified EPPG electrode in RTILs and verifying the presence of “defects” on both EPPG and MWCNTs using cyclic voltammograms (CVs) of Fc obtained in RTILs of EMIBF₄, is the main contribution of this preliminary work.     

Electrochemical determination of sulfide at various carbon substrates: a comparative study.

The direct electrochemical oxidation of sodium sulfide has been examined at five different carbon-based electrode substrates (glassy carbon (GC), boron-doped diamond (BDD), edge-plane pyrollytic graphite (EPPG), basal-plane pyrollytic graphite (BPPG) and carbon nanotubes (CNT)). An electrocatalytic response is observed at both the EPPG and CNT electrode compared to that of the other three substrates. The higher capacitative charging currents obtained at the CNT electrode hinder its detection range and, as such, the EPPG electrode has been clearly shown to be the substrate of choice for the direct electrochemical detection of sulfide. The procedure was applied to the recovery of a sulfide spike in river water, with a recovery of 104%.     

Anodic stripping voltammetry of antimony at unmodified carbon electrodes

Antimony is an element of significant environmental concern, yet has been neglected relative to other heavy metals in electroanalysis. As such very little research has been reported on the electroanalytical determination of antimony at unmodified carbon electrodes. In this paper we report the electrochemical determination of Sb(III) in HCl solutions using unmodified carbon substrates, with focus on non-classical carbon materials namely edge plane pyrolytic graphite (EPPG), boron doped diamond (BDD) and screen-printed electrodes (SPE). Using differential pulse anodic stripping voltammetry, EPPG was found to give a considerably greater response towards antimony than other unmodified carbon electrodes, allowing highly linear ranges in nanomolar concentrations and a detection limit of 3.9?nM in 0.25?M HCl. Furthermore, the sensitivity of the response from EPPG was 100 times greater than for glassy carbon (GC). Unmodified GC gave a comparable response to previous results using the bare substrate, and BDD gave an improved, yet still very high limit of detection of 320?nM compared to previous analysis using an iridium oxide modified BDD electrode. SPEs gave a very poor response to antimony, even at high concentrations, observing no linearity from standard additions, as well as a major interference from the ink intrinsic to the working electrode carbon material. Owing to its superior performance relative to other carbon electrodes, the EPPG electrode was subjected to further analytical testing with antimony. The response of the electrode for a 40?nM concentration of Sb(III) was reproducible with a mean peak current of 1.07?µA and variation of 8.4% (n?=?8). The effect of metals copper, bismuth and arsenic were investigated at the electrode, as they are common interferences for stripping analysis of antimony.     

Direct Electrooxidation of Ascorbic Acid at the Nanocrystaline Graphite‐like Pyrolytic Carbon Film Electrode

Pyrolytic carbon films (PCFs) were prepared by chemical vapor deposition (CVD) at different deposition temperatures. As an example of using PCF electrode in electroanalysis, the direct electrooxidation of ascorbic acid (AA) at the PCF electrode was investigated and compared with common carbon‐based electrodes such as glassy carbon (GC), edge plane pyrolytic graphite (EPPG), and basal plane pyrolytic graphite (BPPG) electrodes. It was found that the PCF electrodes prepared under deposition temperatures higher than 1050 °C showed a higher sensitivity and lower overpotential compared to the other carbon electrodes. The electrode was successfully applied for determination of AA in real samples.     

聚酚藏花红功能碳纳米管生物阳极制备及其在乙醇传感器应用

应用电化学法聚合酚藏花红（PPS）功能化的单壁碳纳米管,以其作为烟酰胺辅酶（NADH）氧化的电化学催化剂（电极）,构建基于乙醇脱氢酶的安培型乙醇生物电化学传感器.该电极于0.0 V时,对NADH具有很好的催化性能.而单体酚藏花红则由于其电位过低（-0.48 V）,不能显示催化性能.循环伏安和计时安培法测试表明：该传感器...     

A promising dehydrogenase-based bioanode for a glucose biosensor and glucose/O2 biofuel cell

A new type of dehydrogenase-based amperometric glucose biosensor was constructed using glucose dehydrogenase (GDH) which was immobilized on the edge-plane pyrolytic graphite (EPPG) electrode modified with poly(phenosafranin)-functionalized single-walled carbon nanotubes (PPS-SWCNTs). The PPS-SWCNT-modified EPPG electrode was prepared by electropolymerization of phenosafranin on the EPPG electrode which had been previously coated with SWCNTs. The performance of the GDH/PPS-SWCNT/EPPG bioanode was evaluated using cyclic voltammetry and amperometry in the presence of glucose. The GDH/PPS-SWCNT/EPPG electrode possesses promising characteristics as a glucose sensor: a wide linear dynamic range of 50 to 700 μM, low detection limit of 0.3 μM, fast response time (1-2 s), high sensitivity (96.5 μA cm(-2) mM(-1)), and anti-interference and anti-fouling abilities. Moreover, the performance of the GDH/PPS-SWCNT/EPPG bioanode was tested in a glucose/O(2) biofuel cell. The maximum power density delivered by the assembled glucose/O(2) biofuel cell could reach 64.0 μW cm(-2) at a cell voltage of 0.3 V with 40 mM glucose.     

Determination of Sb(V) Using Differential Pulse Anodic Stripping Voltammetry at an Unmodified Edge Plane Pyrolytic Graphite Electrode

Antimony(V) determination at an unmodified edge plane pyrolytic graphite (EPPG) electrode using anodic stripping voltammetry (ASV) by depositing beyond the hydrogen wave is shown in this paper. By depositing beyond the hydrogen wave, we report a sensitive method to determine pentavalent antimony at a carbon electrode in 0.25 M HCl. Using differential pulse anodic stripping voltammetry (DPASV), a bare EPPG electrode gave a detection limit of 5.8±0.02 nM without the need for surface modification. This level is greatly within the EU limit for drinking water of 40 nM.     

Enhanced Performance of Edge‐Plane Pyrolytic Graphite (EPPG) Electrodes over Glassy Carbon (GC) Electrodes in the Presence of Surfactants: Application to the Stripping Voltammetry of Copper

The voltammetric performance of glassy carbon (GC) and edge‐plane pyrolytic graphite (EPPG) electrodes was investigated for the oxidation of potassium ferrocyanide in aqueous solution both with and without the addition of surfactant (sodium dodecyl sulfate and Triton X‐100). The heterogeneous electron transfer kinetics were determined for all cases, and it was found that the GC electrode surface was far more sensitive to the presence of surfactant than the more hydrophilic EPPG surface. This result was then applied to the electroanalysis of copper via adsorptive stripping voltammetry in the presence of Triton X‐100 and it was observed that the EPPG electrode response was unaffected by up to 100 μM of surfactant, whilst the voltammetry on the GC electrode was significantly affected by only 10 μM.     

Electrochemistry of Levo‐Thyroxin on Edge‐Plane Pyrolytic Graphite Electrode: Application to Sensitive Analytical Determinations

The electrochemical response of sodium levo‐thyroxin (T₄) at the surface of an edge plane pyrolytic graphite (EPPG) electrode is investigated using cyclic voltammetric technique in the presence of 0.1 M HCl as supporting electrolyte. T₄ underwent totally irreversible oxidation at this system and a well‐defined peak at 821 mV was obtained. Compared to the signals obtained in the optimized conditions at bare glassy carbon and carbon paste electrodes, the oxidation current of T₄ at an EPPG electrode was greatly enhanced. The electrochemical process of T₄ was explored and the experimental conditions were optimized. The oxidation peak current represented a linear dependence on T₄ concentration from 0.01 to 10 µM. The detection limit of 3 nM (S/N=3) was obtained for 250 s accumulation at 0.3 V. Determination of T₄ in a synthetic serum sample demonstrated that this sensor has good selectivity and high sensitivity.     

On reproducibility of preparation of basal plane pyrolytic graphite electrode surface

The basal plane pyrolytic graphite (BPPG) electrode is widely used as a “standard” electrode for studies of electrochemical activity of graphite, graphene and carbon nanotubes. We compared here different methods for preparation of the surface of BPPG using statistical analysis of the data. We showed that including/omitting of polishing step or including/omitting of acetone washing step in the preparation procedure exhibits statistically significant difference. However, using acetone of different purities does not lead into statistically significant results. In addition, all methods with BPPG provided RSD < 10% and did not produce any outlying results.     

Voltammetric Determination of Iron(III) in Water

A square wave voltammetric procedure for the determination of trace amounts of Fe(III) was developed at an unmodified edge plane pyrolytic graphite (EPPG) electrode and a screen printed electrode (SPE). This simple procedure was applied to real samples of commercially bottled mineral water. Sensitive results in the micromolar region could be achieved without modification of the electrode. Using the WHO guideline limits for the Fe(III) concentration in drinking water, recovery percentages at an EPPG gave 103 % and 107 %, and 98.6 % and 95.0 % at a SPE for the 5.36 µM (0.3 mg L^?1) and 53.6 µM (3.0 mg L^?1) additions of Fe(III), respectively.     

A Comparison of Electron Transfer Kinetics of Three Common Carbon Electrode Surfaces in Acetonitrile and in Room Temperature Ionic Liquid 1‐Butyl‐3‐Methylimidiazonium Hexafluorophosphate: Correlation to Surface Structure and the Limit of the Diffusion Domain Approximation

We report the comparison of electron transfer kinetic parameters of the ferrocene redox couple in both acetonitrile and in room temperature ionic liquid (RTIL) 1‐butyl‐3‐methylimidiazonium hexafluorophosphate ([C₄mim] [PF₆]), using edge plane pyrolytic graphite (EPPG), basal plane pyrolytic graphite (BPPG) and glassy carbon (GC) electrodes. Each electrode surface was characterized using SEM and AFM and the surface morphology was analyzed in terms of surface heterogeneity including the distribution of edge plane defects. The experimental data were modeled using both one and two dimensional simulations to correlate the electron transfer parameters obtained with the different surface structure of each electrode. Furthermore, we show that the diffusion domain approximation (commonly used to accurately simulate electron transfer kinetics at graphitic surfaces) breaks down when a BPPG electrode is used in RTIL and demonstrate the near impossibility of assigning rate constant to the basal plane surface.     

Application of anodized edge-plane pyrolytic graphite electrode for analysis of clindamycin in pharmaceutical formulations and human urine samples

Different graphitic carbon-based electrode materials were evaluated for direct electro-oxidation of clindamycin and electroanalytical parameters such as sensitivity, residual background current, and signal-tobackground current ratio were compared to select the best one for the clindamycin electroanalysis. Such electrode materials include glassy carbon, carbon paste, pyrolytic graphite (edge-plane and basal-plane), carbon nanotube, reduced graphene oxide, and carbon black. The edge-plane pyrolytic graphite electrode after a simple and fast electrochemical pretreatment showed superior performance compared with the other carbon electrodes. Raman and Fourier transform infrared spectroscopy were employed to analyze the surface microstructure and chemical bonding of the carbon materials and scanning electron microscopy was used to study their surface morphologic features. The applicability of the electrochemically activated edge-plane pyrolytic graphite electrode for the determination of clindamycin in pharmaceutical formulations and human urine samples was evaluated.     

Exploration of gas sensing possibilities with edge plane pyrolytic graphite electrodes: nitrogen dioxide detection

The voltammetric response of nitrogen dioxide in aqueous sulfuric acid using an edge plane pyrolytic graphite electrode has been explored and contrasted with that from basal plane pyrolytic graphite, glassy carbon or boron-doped diamond electrodes. Edge plane graphite electrode is found to produce an excellent voltammetric signal in comparison with other carbon-based electrodes exhibiting a well-defined analytically useful voltammetric redox couple in 2.5 M sulfuric acid which is absent on the alternative electrodes.     

Exploring the physicoelectrochemical properties of graphene

Convincing evidence is presented demonstrating that the electro-catalytic nature of graphene resides in electron transfer from the edge of graphene which structurally resembles the behaviour of edge plane (rather than basal plane) of highly ordered pyrolytic graphite. The impact of surfactants intrinsic to graphene on the electrochemical response is highlighted.     

Functionalization of Graphene Derivatives with Conducting Polymers and Their Applications in Uric Acid Detection

In this article, we review recent progress concerning the development of sensorial platforms based on graphene derivatives and conducting polymers (CPs), alternatively deposited or co-deposited on the working electrode (usually a glassy carbon electrode; GCE) using a simple potentiostatic method (often cyclic voltammetry; CV), possibly followed by the deposition of metallic nanoparticles (NPs) on the electrode surface (ES). These materials have been successfully used to detect an extended range of biomolecules of clinical interest, such as uric acid (UA), dopamine (DA), ascorbic acid (AA), adenine, guanine, and others. The most common method is electrochemical synthesis. In the composites, which are often combined with metallic NPs, the interaction between the graphene derivatives—including graphene oxide (GO), reduced graphene oxide (RGO), or graphene quantum dots (GQDs)—and the CPs is usually governed by non-covalent functionalization through π–π interactions, hydrogen bonds, and van der Waals (VW) forces. The functionalization of GO, RGO, or GQDs with CPs has been shown to speed up electron transfer during the oxidation process, thus improving the electrochemical response of the resulting sensor. The oxidation mechanism behind the electrochemical response of the sensor seems to involve a partial charge transfer (CT) from the analytes to graphene derivatives, due to the overlapping of π orbitals.     

Electrochemical Determination of Oxalate at Pyrolytic Graphite Electrodes

The electrocatalytic oxidation of oxalate at several carbon based electrodes including basal plane (BPPG) and edge plane (EPPG) pyrolytic graphite and glassy carbon (GC) electrode, was studied. The electrodes were examined for the sensing of oxalate ions in aqueous solutions and all three electrodes showed a response to oxalate additions. The peak of oxalate oxidation at BPPG electrode appeared at lower potential, +1.13 V vs. SCE, than at EPPG (+1.20 V vs. SCE) and GC electrode (+1.44 V vs. SCE). Oxalate oxidation at BPPG electrode was studied in more details for response characteristics (potential and current), effects of pH, temporal characteristics of response potential and current. The results indicated that oxalate oxidation proceeds as two‐electron process at the BPPG electrode with a transfer coefficient β and a diffusion coefficient D evaluated to be 0.45 and 1.03 (±0.04)×10^?5 cm² s^?1 respectively. The BPPG electrode was found to be suitable for oxalate determination in aqueous media showing linear response to oxalate concentration with a sensitivity of 0.039 AM^?1 and a limit of detection of 0.7 μM.