Comprehensive separation of a wide variety of compounds from olive leaves by counter-current chromatography with three-phase solvent system

The three-phase solvent system counter-current chromatography has been of great research interest, because it can separate compounds with a wide range of polarity. The solvent system of n-hexane/methyl tert-butyl ether/acetonitrile/water (5:5:7:5, v/v) was used for counter-current chromatographic comprehensive separation of olive leaves. The study adopted the normal elution mode. The middle phase and the lower phase (at a volume ratio of 7:3) were pumped into the column simultaneously, followed by eluting with the upper, middle, and lower phases in sequence. The retention rate of the stationary phase measured by the experiment was 73.5%. The upper phase was used to elute the nonpolar compounds, then the mobile phase was switched to the middle phase to elute the moderately hydrophobic compounds, finally, the polar compounds were eluted by the lower phase remaining in the chromatographic column. This method successfully separated eight compounds in one step within 270 min and five compounds were identified. The logP values of these five compounds were 7.44, 7.86, 4.16, −0.11, and 0.96, respectively, covering a wide range of polarities. The present study demonstrated that the three-phase solvent has a strong extraction capacity for ingredients from extremely hydrophilic compounds to extremely hydrophobic compounds.     

UV-based solvent system screening for high-speed counter-current chromatography fractionation of compounds with similar UV absorption from complex samples followed by preparative HPLC purification: Flavonoids from barley seedlings as sample

This article proposes a solvent system screening strategy for compounds with similar UV absorption in complex samples by UV spectrophotometer. There is no need to calculate the partition coefficient value of each compound, only the partition coefficient of the whole sample. The partition coefficient value should be close to 1 in order to obtain as many high-speed counter-current chromatography fractions as possible. Then, preparative HPLC was used to purify the high-speed counter-current chromatography fractions. Based on the above strategy, seven c-glycosyl flavonoids and an amino acid were successfully obtained from barley seedlings through high-speed counter-current chromatography fractionation with ethyl acetate/n-butanol/water (8:2:10, v:v:v) system followed by preparative HPLC purification. The research shows that high-speed counter-current chromatography could be well developed as a tool for fractionation before purification, and greatly improves the separation efficiency.     

Organic high ionic strength aqueous two-phase solvent system series for separation of ultra-polar compounds by spiral high-speed counter-current chromatography

Existing two-phase solvent systems for high-speed countercurrent chromatography cover the separation of hydrophobic to moderately polar compounds, but often fail to provide suitable partition coefficient values for highly polar compounds, such as sulfonic acids, catecholamines and zwitter ions. The present paper introduces a new solvent series which can be applied for the separation of these polar compounds. It is composed of 1-butanol, ethanol, saturated ammonium sulfate and water at various volume ratios and consists of a series of 10 steps which are arranged according to the polarity of the solvent system so that the two-phase solvent system with suitable K values for the target compound(s) can be found in a few steps. Each solvent system gives proper volume ratio and high density difference between the two phases to provide a satisfactory level of retention of the stationary phase in the spiral column assembly. The method is validated by partition coefficient measurement of four typical polar compounds including methyl green (basic dye), tartrazine (sulfonic acid), tyrosine (zwitter ion) and epinephrine (a catecholamine), all of which show low partition coefficient values in the polar 1-butanol-water system. The capability of the method is demonstrated by separation of three catecholamines.     

Application of one-step inner-recycling counter-current chromatography for the preparative separation and purification of chemical constituents from the rhizome of Bergenia ciliate (haw.) Sternb

Bergenia ciliata (haw.) Sternb, the renowned pharmaceutical plant in Jammu and Kashmir of Pakistan, is widely applied in treating different illnesses including diabetes, diarrhea, and vomiting. This work employed an efficient one-step inner-recycling counter-current chromatography for preparative separating and purifying compounds with similar partition coefficients from the rhizome of Bergenia ciliate (haw.). Five compounds, including quercetin rhamnodiglucoside ( 1 ), quercetin-3-O-rutinoside ( 2 ), bergenine ( 3 ), kaempferol ( 4 ), and palmatic acid ( 5 ), were successfully separated using the optimized biphasic solvent system that contained ter-butylmetylether/n-butanol/acetonitrile/water (2:2:1:5, v/v) with the purities over 98%. Mass spectrometry and nuclear magnetic resonance were conducted for structural identification. As a result, our proposed strategy might be applied in separating compounds with similar partition coefficients, which was advantageous with regard to the less solvent and time consumption, and the increased number of theoretical plates.     

Solvent system selection in counter-current chromatography using conductor-like screening model for real solvents

The aim of this investigation was to minimize the experimental effort for solvent system selection in counter-current chromatography. The separation mechanism in counter-current chromatography is based exclusively on the partitioning of the solute between the two liquid phases. Therefore, a quantum chemical method combined with statistical thermodynamics (conductor-like screening model for real solvents, COSMO-RS) was used for the prediction of the partition coefficient. A comparison of the experimental and predicted data for five model solutes systems demonstrated the potential of the use of COSMO-RS as a screening tool for the solvent system selection.     

Rational development of a selection model for solvent gradients in single-step separation of ginsenosides from Panax ginseng using high-speed counter-current chromatography

A new model of solvent gradients selection was rationally developed for the preparative separation of target compounds. The solvent gradients were selected based on a three-stage screening process where stationary phase retention was ensured by introducing a new parameter termed as the phase ratio. The phase ratio was calculated after mixing the upper phase of a solvent system with the lower phase of a different solvent system (1:1, v/v). The developed model was applied to the one-step separation of eight ginsenosides from Panax ginseng. Three gradients were selected on the basis of new model and eight ginsenosides, Rb(1), Rb(2), Rc, Rd, Re, Rg(1), Rf, and Rh(1), were efficiently separated by high-speed counter-current chromatography coupled with evaporative light scattering detector. The structures of all compounds were characterized by electrospray-ionization mass spectrometry and nuclear magnetic resonance spectroscopy.     

Application of calcium oxide as an efficient phase separation agent in temperature-induced counter-current homogenous liquid-liquid extraction of aflatoxins from dried fruit chips followed by high-performance liquid chromatography-tandem mass spectrometry determination

A temperature-induced counter-current homogenous liquid-liquid extraction procedure performed in a burette has been proposed for the isolation of aflatoxins B1, B2, G1, and G2 from various fruit chip samples. In this method, a homogenous solution of deionized water and cyclohexylamine is added to the solid sample and the resulted mixture is vortexed. In the following, the liquid phase is taken and passed through the burette filled with a mixture of calcium oxide (as a phase separation agent) and sand (to avoid clumping the calcium oxide). By doing so, the temperature of the solution is increased by hydration of calcium oxide and consequently, the homogenous state is broken and the aflatoxins are migrated into the resulted tiny droplets of cyclohexylamine. This phase is collected on the top of the solution owing to its low density with respect to an aqueous solution. Numerous parameters which can affect the efficiency of the suggested approach were evaluated and under the best situations, great repeatability, low limits of determination and quantification, and high extraction recoveries were acquired. In the end, the suggested approach was employed for the quantification of the selected aflatoxins in various fruit chips samples marketed in Tabriz City, Iran.     

The reactivity of tributyltin oxygen compounds with CCl4: Implications for its use as an extraction/reaction solvent

A variety of tributyltin oxygen compounds,(nC₄H₉)₃SnOX where X = Sn(nC₄H₉)₃, C₂H₅, nC₄H₉, C₈H₁₇, CH₂C₆H₅, COCH₃, have been studied in refluxing CCI₄. A reaction was observed to occur where X = C₂H₅, C₄H₉, C₈H₁₇, CH₂C₆H₅, leading to the formation of (nC₄H₉)₃SnCl, CHCl₃ and an aldehyde. Possible reaction pathways are suggested. These reactions have implications for the use of CCl₄ as an extraction/reaction solvent.     

Development of an efficient method for the preparative isolation and purification of chlorophyll a from a marine dinoflagellate Amphidinium carterae by high-speed counter-current chromatography coupled with reversed-phase high-performance liquid chromatography

In our research into chlorophylls of marine dinoflagellates, chlorophyll a was separated rapidly from the hexane extract of Amphidinium carterae in three steps. The first step was silica gel column chromatography, where elution was performed with 0–50% ethyl acetate in n-hexane. The second was high-speed counter-current chromatography using a two-phase solvent system consisting of n-hexane–ethyl acetate–methanol–water (5:5:5:1, v/v), and the third step was preparative reversed-phase high-performance liquid chromatography using a solvent system of acetone–water (89:11, v/v). HPLC analysis showed that the purity of chlorophyll a from the second step was over 83%, and after the third it was over 99%. Thirty milligrams of chlorophyll a was isolated from a crude sample of 250 mg of chlorophylls, and its structure was identified by analyzing its MS, ¹H NMR and ¹³C NMR spectra.     

Three-phase system in solvent bar microextraction: An approach for the sample preparation of ionizable organic compounds prior to liquid chromatography

In this article, a simple new solvent microextraction technique is described for the extraction of ionizable organic compounds. This involves performing simultaneous forward- and back-extraction across an organic film immobilized in the pores of a porous polypropylene hollow fiber. Four chlorophenoxyacetic acid herbicides were chosen as model compounds. The target compounds are extracted from the stirred acidic aqueous sample (adjusted to 0.5 M HCl; donor phase) through a thin film of an organic solvent residing in the pores of a polypropylene hollow fiber; they are then finally extracted into another alkaline aqueous phase (1 M NaOH; acceptor phase). Both ends of the fiber are pressure-sealed. The acceptor phase was analyzed by liquid chromatography (LC). This method gave good enrichment (by a factor of 438-553) of the analytes in 40 min extraction time with reasonably good reproducibility. The analytical potential of the method was demonstrated by applying the method to spiked river water sample.     

Preparative isolation and purification of ginsenosides Rf,Re, Rd and Rb1 from the roots of Panax ginseng with a salt/containing solvent system and flow step-gradient by high performance counter-current chromatography coupled with an evaporative light scattering detector

Ginseng is a popular herb worldwide and has had varied uses in traditional Asian medicine for thousands of years. There are several different species of the herb, but all share the same constituents. Ginsenosides, the most extensively studied chemical components of ginseng, are generally considered to be one of the most important active ingredients of the plant. In this study, we have developed fast and efficient methodology for isolation of four known ginsenosides Rf, Rd, Re and Rb1 from Ginseng by high performance counter-current chromatography (HPCCC) coupled with evaporative light scattering detection (ELSD). The crude sample for HPCCC was purified firstly from a ginseng extraction using macroporous resin. The enriched saponin fraction (480 mg) was separated by using methylene chloride–methanol–5 mM aqueous ammonium acetate–isopropanol (6:2:4:3, v/v,) as the two-phase solvent system and yielded 10.7 mg of Rf, 11.0 mg of Rd, 13.4 mg of Re and 13.9 mg of Rb1. The purity of these ginsenosides was 99.2%, 88.3%, 93.7% and 91.8%, respectively assessed by HPLC-DAD-ELSD, and their structures were characterized by electrospray ionization mass spectrometry (ESI-MS) and compared with standards. Ammonium acetate was used to shorten the separation time and eliminate emulsification together with a flow step-gradient. The salt can be removed by re-dissolving the sample using acetone.     

Fluorocarbon-bonded magnetic mesoporous microspheres for the analysis of perfluorinated compounds in human serum by high-performance liquid chromatography coupled to tandem mass spectrometry

We report herein an extraction method for the analysis of perfluorinated compounds in human serum based on magnetic core–mesoporous shell microspheres with decyl-perfluorinated interior pore-walls (Fe₃O₄@mSiO₂-F₁₇). Thanks to the unique properties of the Fe₃O₄@mSiO₂-F₁₇ microspheres, macromolecules like proteins could be easily excluded from the mesoporous channels due to size exclusion effect, and perfluorinated compounds (PFCs) in protein-rich biosamples such as serum could thus be directly extracted with the fluorocarbon modified on the channel wall without any other pretreatment procedure. The PFCs adsorbed Fe₃O₄@mSiO₂-F₁₇ microspheres could then be simply and rapidly isolated by using a magnet, followed by being identified and quantified by LC–MS/MS (high-performance liquid chromatography coupled to tandem mass spectrometry). Five perfluorinatedcarboxylic acids (C6, C8–C11) and perfluorooctane sulfonate (PFOS) were selected as model analytes. In order to achieve the best extraction efficiency, some important factors including the amount of Fe₃O₄@mSiO₂-F₁₇ microspheres added, adsorption time, type of elution solvent, eluting solvent volume and elution time were investigated. The ranges of the LOD were 0.02–0.05 ng mL⁻¹ for the six PFCs. The recovery of the optimized method varies from 83.13% to 92.42% for human serum samples.     

Validation of a liquid chromatography coupled with tandem mass spectrometry method for the determination of drugs in wastewater using a three‐phase solvent system

Pharmaceuticals constitute one of the most important emerging classes of environmental pollutants. A three‐phase solvent system of water, water containing 0.1% of formic acid and acetonitrile was successfully used to separate, by liquid chromatography with mass spectrometry (LC‐MS), polarity‐matched pharmaceuticals, that is, carbamazepine, clarithromycin, and erythromycin, as well as amoxicillin and metformin. Despite of polarity similarities, these pharmaceuticals were completely resolved in the analytical run time of 15 min. The optimized three‐phase solvent system based‐method was validated for the simultaneous analysis of six matched‐polarity pharmaceuticals in wastewater samples. Good linearity (coefficient of determination more than 0.993) and precision (relative standard deviation less than 15.66%) were achieved. Recovery of analytes from the wastewater was between 0.70 and 1.18. Limits of detections ranged from 0.0001 to 0.5114 µg/L. No significant matrix effect, evaluated by post extraction addition, was observed in the electrospray ionization (ESI) source. Then, this methodology has been successfully applied to environmental study of pharmaceutical residues occurring in influent and effluent wastewater samples, from the main wastewater treatment plant in Potenza (Basilicata, Southern Italy).     

Optimization of an accelerated solvent extraction dispersive liquid–liquid microextraction method for the separation and determination of essential oil from Ligusticum chuanxiong Hort by gas chromatography with mass spectrometry

In this study, an accelerated solvent extraction dispersive liquid–liquid microextraction coupled with gas chromatography and mass spectrometry was established and employed for the extraction, concentration and analysis of essential oil constituents from Ligusticum chuanxiong Hort. Response surface methodology was performed to optimize the key parameters in accelerated solvent extraction on the extraction efficiency, and key parameters in dispersive liquid–liquid microextraction were discussed as well. Two representative constituents in Ligusticum chuanxiong Hort, (Z)‐ligustilide and n‐butylphthalide, were quantitatively analyzed. It was shown that the qualitative result of the accelerated solvent extraction dispersive liquid–liquid microextraction approach was in good agreement with that of hydro‐distillation, whereas the proposed approach took far less extraction time (30 min), consumed less plant material (usually <1 g, 0.01 g for this study) and solvent (<20 mL) than the conventional system. To sum up, the proposed method could be recommended as a new approach in the extraction and analysis of essential oil.     

Multi-location peak parking method: an important new tool for the study of mass transfer kinetics in liquid chromatography

The peak parking (PP) method probes the longitudinal diffusion coefficient of a compound at a single location along the chromatographic column. We extended to a so-called multi-location peak parking (MLPP) method, in which a large number of axial locations along the column are selected in order to check the validity of the conventional PP method and to reveal possible defaults in the structure of the packed bed or pitfalls of the PP and the MLPP methods. MLPP was applied to a series of HILIC columns, including a 5.0 μm Venusil, a 3.0 μm Luna-diol, three 2.7 μm Halo, and a 1.7 μm Kinetex columns. The results demonstrate that the MLPP method may reveal local heterogeneities in the axial diffusion of small retained low molecular weight compounds along the column. Most importantly, experiments show that the sample zone should not be parked in the entrance of the column (i.e., at <1/10 th of the column length). The abrupt drop in the flow rate considerably affects the peak shape and prevents scientists from using the conventional PP method. Practical solutions to cope with that problem are proposed and their success/failure are discussed.     

Comparison of different extraction procedures for the comprehensive characterization of bioactive phenolic compounds in Rosmarinus officinalis by reversed-phase high-performance liquid chromatography with diode array detection coupled to electrospray time-of-flight mass spectrometry

In the present work, a comparative study between two environmentally friendly and selective extraction techniques, such as supercritical fluid extraction (SFE) and pressurized liquid extraction (PLE) have been carried out focusing in the bioactive phenolic compounds present in Rosmarinus officinalis. For the analysis of the SFE and PLE extracts, a new methodology for qualitative characterization has been developed, based on the use of reversed-phase high-performance liquid chromatography (RP-HPLC), equipped with two different detection systems coupled in series: diode array detector (DAD) and time of flight mass spectrometry (TOF-MS) detector connected via an electrospray ionization interface (ESI). The use of a small particle size C(18) column (1.8 μm) provided a great resolution and made possible the separation of several isomers. Moreover, UV-visible spectrophotometry is a valuable tool for identifying the class of phenolic compounds, whereas MS data enabled to structurally characterize the compounds present in the extracts. The applied methodology was useful for the determination of many well-known phenolic compounds present in R. officinalis, such as carnosol, carnosic acid, rosmadial, rosmanol, genkwanin, homoplantaginin, scutellarein, cirsimaritin and rosmarinic acid, as well as other phenolic compounds present in other species belonging to Lamiaceae family.