High-efficiency Simple Structure White Organic Light-emitting Devices Based on Rubrene Ultrathin Layer

White organic light-emitting devices (WOLEDs) were fabricated with an ultrathin layer of rubrene inserted between NPB and TPBI. With a simple three-layer structure of ITO/NPB(50 nm)/rubrene(0.1 nm)/TPBI(50 nm)/LiF/Al, a white light with CIE coordinates of (0.31, 0.30) were generated. The device gave a maximum luminance efficiency of 2.04 lm/W at 5 V. Furthermore, with a multilayer structure of ITO/m-MTDATA(30 nm)/NPB(20 nm)/rubrene(0.1 nm)/TPBI(40 nm)/Alq₃(10 nm)/LiF/Al, the device reached a maximum luminance efficiency of 4.29 lm/W at 4 V and the luminance could exceed 10 000 cd/m² at 10 V.     

钬铥双掺钨酸镱钾激光晶体光谱参数计算

采用顶部籽晶提拉法（TSSG）生长了钬铥双掺钨酸镱钾（KHo_0.04Tm_0.06Yb_0.9（WO₄）₂）激光晶体。测试了该晶体的吸收及荧光光谱,计算了其光谱参数。实验结果表明：该晶体在890~1 000 nm范围吸收带较宽,半峰宽为90 nm,计算了主峰1 000 nm处吸收截面为16.92×10^-20 cm²;Tm³⁺在1 690~1 812 nm范围存在较宽的吸收带,半峰宽为118 nm,易于实现Yb→Ho、Yb→Tm、Tm→Ho的能量传递。根据Judd-Ofelt理论,计算了该晶体的光谱强度参数。根据Tm³⁺、Ho³⁺、Yb³⁺离子能级图,讨论了产生1 750~2 200 nm荧光发射的3种能量传递方式。最后计算了主峰2 030 nm处受激发射截面为3.47×10^-20 cm²,表明该晶体可作为2 μm波段优异的激光增益介质。     

金原子团簇的分频散射光谱研究

液相金原子团簇是一种非线性光学介质.它在580nm处产生一个最强共振散射峰.当激发波长为290nm(1.03×10¹⁵Hz)时,液相金原子团簇在580nm(1/2×1.03×10¹⁵Hz)和870nm(1/3×1.03×10¹⁵Hz)分别产生一个1/2分频和1/3分频散射峰;当激发波长为580nm(5.02×10¹⁴Hz)时在290nm(2×5.02×10^-14Hz)和870nm(2/3×5.02×10¹⁴Hz)分别产生一个2倍频和2/3分频散射峰;当激发波长为870nm(3.34×10¹⁴Hz)时在580nm(3/2×3.34×10¹⁴Hz)和290nm(3×3.34×10¹⁴Hz)分别产生一个3/2分频和3倍频散射峰.分频散射和倍频散射峰与共振散射峰具有相似的散射行为.从激励光与液相金原子团簇相互作用的运动方程出发,根据傅氏变换理论,较好地解释了液相金原子团簇产生的一些非线性散射光谱.     

Characterization of TiO2/Au/TiO2 films deposited by magnetron sputtering on polycarbonate substrates

Transparent and conducting TiO₂/Au/TiO₂ (TAuT) films were deposited by reactive magnetron sputtering on polycarbonate substrates to investigate the effect of the Au interlayer on the optical, electrical, and structural properties of the films. In TAuT films, the Au interlayer thickness was kept at 5 nm. Although total thickness was maintained at 100 nm, the stack structure was varied as 50/5/45, 70/5/25, and 90/5/5 nm.In XRD pattern, the intermediate Au films were crystallized, while all TAuT films did not show any diffraction peaks for TiO₂ films with regardless of stack structure. The optical and electrical properties were dependent on the stack structure of the films. The lowest sheet resistance of 23 Ω/□ and highest optical transmittance of 76% at 550 nm were obtained from TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films. The work function was dependent on the film stack. The highest work function (4.8 eV) was observed with the TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm film stack. The TAuT film stack of TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films is an optimized stack that may be an alternative candidate for transparent electrodes in flat panel displays.     

Two-photon absorption and nonlinear optical properties of a new organic dye PSPI

Trans-4-[p-(pyrrolidinyl)styryl]-N-methylpyridinium iodide (abbreviated as PSPI thereafter) is a two-photon absorption (TPA) dye newly synthesized by our research group. It possesses much larger TPA cross-section and much stronger upconversion fluorescence emission than those of common organic dye (such as rhodamine) when excited with near infrared (IR) radiation. TPA spectrum and upconversion efficiency spectrum of HEASPI solution at various wavelengths were measured. There is 34 nm blue shift for the central wavelength of the TPA induced absorption peak compared with two times of the linear absorption peak. The biggest molecular TPA cross-section σ₂^′ is 2.85×10⁻⁴⁷ cm⁴ s/photon at 930 nm. At 1064 nm, σ₂^′ is 3.12×10⁻⁴⁸ cm⁴ s/photon. The highest efficiency is 3.9% at 1010 nm, whereas 2.9% at 1064 nm. Its optical power limiting properties at 930 nm have also been illustrated.     

基于单波长外腔共振和频技术产生波长可调谐589 nm激光及钠原子饱和荧光谱的测量

本文基于新型单波长外腔共振和频技术实现了转换效率高、波长可调谐589 nm激光的输出, 其中基频光波长分别为1583 nm和938 nm, 和频晶体为周期极化铌酸锂. 在1583 nm激光频率被锁定到外部环形腔腔模后, 通过对938 nm激光的频率扫描实现了输出功率4.96 mW, 调谐范围7 GHz的589 nm激光输出, 并采用声光调制器的伺服反馈技术有效提高了输出功率的稳定性. 最后采用该光源对钠原子在348—413 K (75—140 ℃)时D₂线的饱和荧光谱进行了测量. 观察到了多普勒背景下钠D₂a, D₂b以及Crossover的亚多普勒结构, 其均可为589 nm频率的锁定提供参考信号. 关键词： 单波长外腔共振 和频 589 nm 钠原子饱和荧光谱     

白色有机发光器件及其稳定性

报道了一种稳定的白色有机薄膜电致发光器件.电流效率6cd/A,在电流密度20mA/cm²驱动下,亮度为1026cd/m²;最高亮度21200cd/m²,色度(x=0.32,y=0.40).该器件具有较平稳的效率电流关系,即具有弱的电流荧光猝灭.初始亮度100cd/m²下,半亮度寿命达22245h.     

基于密度泛函理论下多肽光谱性质研究

多肽类物质在生物医药等领域是一种重要的生物大分子,而紫外-可见吸收光谱和荧光光谱是研究生物分子精细结构的重要手段。采用密度泛函理论（DFT/RI）计算了生长激素释放肽（GHRP-6）和催产素（Oxytocin）两种多肽的结构模型和分子前线轨道;在含时密度泛函理论（TDDFT）的基础上,引入了TDA等近似,建立了多肽类物质的紫外-可见吸收光谱和荧光光谱的理论模型。结果表明,实验测得到GHRP-6的紫外-可见吸收光谱最大吸收波长为279 nm,计算得到的最大吸收波长为282 nm,误差为3 nm,误差百分比约为1%;Oxytocin紫外-可见吸收光谱的实验值为275 nm,计算值为269 nm,误差百分比约为2%。GHRP-6荧光光谱计算值为368 nm,实验值为360 nm,误差百分比约为2%;Oxytocin荧光光谱计算值为305 nm,实验值为312 nm,误差百分比约为2%。GHRP-6产生荧光的发射波长与色氨酸产生的荧光波长范围相近,说明GHRP-6产生荧光的主要贡献为色氨酸残基上的π→π*轨道跃迁,Oxytocin荧光峰位置与酪氨酸产生的荧光波长范围相近,Oxytocin产生荧光的主要贡献为酪氨酸残基上的π→π*轨道跃迁。根据该模型计算得到的光谱与实验结果吻合度较高,表明该模型能够准确计算多肽类物质紫外-可见吸收光谱和荧光光谱,为实验提供可靠的理论依据。     

冷鲜猪肉的三维荧光光谱特征研究

利用三维荧光光谱技术,研究了冷鲜猪肉三维荧光光谱特征,主要探讨了不同温度存储条件下冷鲜猪肉荧光峰的位置和荧光峰所处区域内荧光强度平均值随存储时间变化的规律,并初步判断了荧光物质的种类,为实现基于三维荧光光谱技术快速、无损检测冷鲜猪肉新鲜度奠定了理论基础。实验结果表明,不同温度存储条件下样本的三维荧光光谱图中均含有2个明显的荧光峰（Peak A和Peak B）,它们所在位置的激发波长（λ_ex）/发射波长（λ_em）范围分别为：λ_ex/λ_em约为250～310 nm/300～400 nm和约为300～450 nm/400～550 nm。其中,Peak A为类蛋白荧光,Peak B为脂质氧化产物荧光。此外,实验还发现,两个荧光峰在各自所处区域内荧光强度的平均值随存储时间变化的趋势不受存储温度影响,均是Peak A在λ_ex/λ_em=250～310 nm/300～400 nm区域内荧光强度的平均值（I_A）逐渐下降,Peak B在λ_ex/λ_em=300～450 nm/400～550 nm区域内荧光强度的平均值（I_B）逐渐上升。但I_A和I_B的变化速率受存储温度影响,冷藏条件下比室温条件下变化慢。     

石油污染水体荧光图谱特征分析

石油类物质对水体吸收系数的影响主要通过黄色物质(CDOM)体现出来,CDOM和石油类物质皆具有荧光基团,如果两者的荧光图谱各自特征明显的话,那么有望利用荧光技术分离出水中石油物质和CDOM各自对水体总吸收系数的贡献,从而提高水体石油类物质含量的遥感反演精度。以大连周边海水和山区水库水为自然水体本底,分别与取自采油污水厂和炼油污水厂的污水进行混合配比,利用试验数据分析了仅含CDOM、含油与CDOM混合、仅含石油三种水样的荧光图谱特征,旨在为利用荧光技术分离出水中石油物质和CDOM各自对水体总吸收系数的贡献提供依据。分析结果表明：(1)自然水体中,海水的CDOM具有三个典型荧光峰,分别位于Ex:225-230 nm/Em:320～330 nm,Ex:280 nm/Em:340 nm和Ex:225-240 nm/Em:430～470 nm,为海水叶绿素碎屑物所致;淡水具有两典型荧光峰,分别位于：Ex：240～260 nm/Em：420～450 nm和Ex：310～350 nm/Em：420～440 nm,为陆源物质所致;(2)用正己烷萃取后的仅含油水样,具有1～3个荧光峰,分别位于Ex: 220～240 nm/Em：320-340 nm,Ex:270～290 nm/Em：310～340 nm和Ex: 220～235 nm/Em：280～310 nm,为各自烃类成分所致;(3)在自然水体中混入油污水后,含油和CDOM的水样荧光图谱呈现出一个非常强的荧光峰,位于Ex：230～250 nm/Em：320～370 nm,为CDOM和石油类物质荧光成分共同作用所致。     

ITO-free inverted organic solar cells fabricated with transparent and low resistance ZnO/Ag/ZnO multilayer electrode

Inverted organic solar cells (OSCs) based on poly (3-hexylthiophene) (P3HT):[6,6]-phenyl-C61 butyric acid methyl ester (PCBM) bulk heterojunctions (BHJ) were fabricated with optimized ZnO/Ag/ZnO multilayer and conventional indium–tin oxide (ITO) cathode electrodes and their performance was compared. The ZnO/Ag/ZnO multilayer films showed sheet resistances in the range 3.6–3.9 Ω/sq, while ITO exhibited 14.2 Ω/sq. On the one hand, the carrier concentration gradually decreased from 1.74 × 10²² to 4.33 × 10²¹ cm⁻³ as the ZnO thickness increased from 8 to 80 nm, respectively. The transmittance of the ZnO(40 nm)/Ag(19 nm)/ZnO(40 nm) films was ∼95% at 550 nm, which is comparable to that of ITO (∼96%). The multilayer films were smooth with a root mean square (RMS) roughness of 0.81 nm. OSCs fabricated with the ZnO(40 nm)/Ag(19 nm)/ZnO(40 nm) film showed a power conversion efficiency (2.63%) comparable to that of OSCs with a conventional ITO cathode (2.71%).     

The effect of thickness and annealing condition on the microstructure and magnetic properties of Fe/Pt multilayer thin films

[Fe(0.5 nm)/Pt(0.5 nm)]₄₀, [Fe(1 nm)/Pt(1.5 nm)]₂₀ and [Fe(3 nm)/Pt(3 nm)]₁₀ multilayer were prepared by DC magnetron sputtering. By conventional furnace annealing (CA) at 270–600 °C for various time, all of the films still remained the disordered structure with the soft magnetic phase. By rapid thermal annealing (RTA) at 500 °C for various time, we obtained the [Fe(1 nm)/Pt(1.5 nm)]₂₀ and [Fe(3 nm)/Pt(3 nm)]₁₀ films with L1₂ ordered FePt₃ phase which was almost ferromagnetic at room temperature. However, the [Fe(0.5 nm)/Pt(0.5 nm)]₄₀ films was still disordered state even under RTA. Compared with CA, RTA exposed an outstanding effect on accelerating the phase transition when the film thickness is over [Fe(0.5 nm)/Pt(0.5 nm)]₄₀.     

RE(POA)3phen配合物的合成、表征及荧光性能

合成了以稀土离子Sm³⁺、Eu³⁺、Tb³⁺、Dy³⁺及Tb³⁺为发光中心,以苯氧乙酸(HPOA)和邻菲罗啉(phen)为配体,掺杂La³⁺、Gd³⁺、 Y³⁺的7种稀土配合物, 对配合物进行了C、H、N元素分析、稀土络合滴定、红外光谱、紫外光谱和发光光谱的研究。结果表明配合物的组成分别为SmL₃L'·1/2H₂O,EuL₃L'·1/2H₂O,TbL₃L'· 1/2H₂O,DyL₃L'·1/2H₂O,掺杂配合物组成分别为Tb_0.5Gd_0.5L₃L'·1/2H₂O,Tb_0.5Y_0.5L₃L'·1/2H₂O,Tb_0.5La_0.5L₃L'·1/2H₂O(L=C₆H₅OCH₂COO^-, L'=phen)。配合物中的稀土离子与苯氧乙酸中羧基的一个氧原子和苯氧基的氧原子配位,与邻菲罗啉中的两个氮原子配位成键;荧光光谱表明,铽三元配合物的发射强度要远大于其它三元配合物的发光强度,掺杂发光惰性稀土离子La³⁺、Gd³⁺、Y³⁺的铽配合物中,Y³⁺掺杂配合物的发光强度有所增强。     

Fluorescence of Eu-activated alkaline earth halosilicates

Three luminescent materials, each with a distinct and novel crystalline structure have been found in the alkaline earth halosilicate series. Their emission is in the blue/green part of the spectrum, the peaks falling at 500 nm for the Sr/Cl compound, 442 nm for the Ca/Cl compound and 514 nm for the Ca/Br compound. The strontium chlorsilicate, Sr₂Si₃O₈ 2SrCl₂, is of particular interest showing good temperature dependence characteristics (365 nm excitation) and also exhibiting an acicular crystal habit. Other alkaline earth/halide combinations and the binary alkaline earth systems were examined.     

High-Efficiency Blue Electroluminescence Based on Coumarin Derivative 3-(4-(anthracen-10-yl)phenyl)-benzo[5,6]coumarin

The electroluminescent (EL) properties of a new coumarin derivative, 3-(4-(anthracen-10-yl)phenyl)-benzo[5,6]coumarin (APBC), were investigated. The results show that the EL devices comprised of vacuum vapor-deposited films using the derivative as dopant exhibited blue emission that is identical to the photoluminescence of the thin film. The electroluminescence device of ITO/2-TNATA (5?nm)/NPB (40?nm)/CBP : APBC (1.0?wt%, 30?nm)/PBD (30?nm)/LiF (1?nm)/Al (100?nm) gives a maximum luminous efficiency of 2.3?cd/A at the current density of 20?mA/cm², and maximum luminance of 5169?cd/m² at 16?V. The external quantum efficiency of the device is 1.85?%.     

Fabrication and characterization of In2O3 nanowires

In₂O₃ nanowires were successfully fabricated through a simple gas-reaction route in argon atmosphere. These nanowires have diameters ranging from 20 nm to 50 nm and lengths up to tens of micrometers. High-resolution transmission electron microscopy observations and the electron-diffraction (ED) pattern reveal that the In₂O₃ nanowires are formed by the stacking of (2) planes along the [1] direction, which is parallel to the wire axis. A strong and wide ultraviolet (UV) emission band centered at around 392 nm is observed for the first time in the room-temperature photoluminescence measurement in addition to the usual blue emission (468 nm). Moreover, five discrete fine peaks (372 nm, 383 nm, 406 nm, 392 nm and 413 nm) are further identified in this broad UV band. Received: 10 April 2002 / Accepted: 12 April 2002 / Published online: 19 July 2002     

基于一种新型有机金属配合物的量子阱结构有机电致白光器件的性能研究

利用一种新型有机金属配合物二(2-(4-三氟甲基-2-羟基苯基)苯并噻唑锌(Zn(4-TfmBTZ)₂),基于NPB/Zn(4-TfmBTZ)₂界面电致激基复合物,制备了一系列异质结量子阱结构有机电致白光器件.结果表明,量子阱结构可以有效提高界面电致激基复合物的发光效率以及器件的显色指数和色度稳定性.得出器件ITO/NPB (60 nm)/Zn(4-TfmBTZ)₂(3.0 nm)/NPB (4.0 nm)/Zn(4-TfmBTZ)_{关键词： 二(2-(4-三氟甲基-2-羟基苯基)苯并噻唑锌 电致激基复合物 量子阱 白光}     

High-contrast and high-efficiency top-emitting organic light-emitting devices

The reflection properties of top-emitting organic light-emitting devices with different electrodes and organic layers were calculated. The results guided the fabrication of a high-contrast device: Au/copper phthalocyanine (CuPc: 35 nm)/N,N’-bis-(1-naphthyl)-N,N’diphenyl-1,1’ biphenyl-4,4’diamine (NPB: 15 nm)/tris(8-hydroxyquinoline) aluminum (Alq₃: 50 nm)/Sm (35 nm)/Alq₃ (65 nm). The device has a contrast ratio of 8.3:1 at a luminance of 300 cd/m² under 1000 lx ambient light, and a maximum luminance and efficiency of 5000 cd/m² and 4.14 cd/A, respectively. The high contrast is attributed to the moderate reflection of Au at 380–550 nm, low reflection of Sm in the visible range, and high absorption of CuPc at 600–700 nm. PACS 85.60.Jb; 78.20.Ci; 78.40.-q     

Superior tolerance of Ag/Ni multilayers against Kr ion irradiation: an in situ study

Monolithic Ag and Ni films and Ag/Ni multilayers with individual layer thickness of 5 and 50?nm were subjected to in situ Kr ion irradiation at room temperature to 1 displacement-per-atom (a fluence of 2?×?10¹⁴?ions/cm²). Monolithic Ag has high density of small loops (4?nm in diameter), whereas Ni has fewer but much greater loops (exceeding 20?nm). In comparison, dislocation loops, ～4?nm in diameter, were the major defects in the irradiated Ag/Ni 50?nm film, while the loops were barely observed in the Ag/Ni 5?nm film. At 0.2?dpa (0.4?×?10¹⁴?ions/cm), defect density in both monolithic Ag and Ni saturated at 1.6 and 0.2?×?10²³/m³, compared with 0.8?×?10²³/m³ in Ag/Ni 50?nm multilayer at a saturation fluence of ～1?dpa (2?×?10¹⁴?ions/cm²). Direct observations of frequent loop absorption by layer interfaces suggest that these interfaces are efficient defect sinks. Ag/Ni 5?nm multilayer showed a superior morphological stability against radiation compared to Ag/Ni 50?nm film.     

修饰阴极界面提高聚合物白光二极管发光效率

利用聚合物的不同溶解性,研究用旋涂方法制备双层高分子白光二极管(WPLED),采用器件结构为：ITO/PEDOT(50nm)/PVK:PFO-BT: PFO-DBT(40nm)/PFO(40nm)/Ba(4nm) /Al(120nm),当相对比例为PVK: PFO-BT:PFO-DBT=1∶4%：3%时,得到标准白光,最大电流效率为2.4 cd/A,最大亮度为3215 cd/m²,色坐标为(0.33,0.34).用水溶性的聚电介质层修饰阴极界面,器件效率可以进一步提高到5.28 cd 关键词： 聚合物发光二极管 白光 双发光层结构