Electrochemical Studies and Selective Detection of Thioridazine Using a Carbon Paste Electrode Modified with ZnS Nanoparticles and Simultaneous Determination of Thioridazine and Olanzapine

A novel ZnS nanoparticle‐modified carbon paste electrode (ZnSNP‐MCPE) was fabricated and used to study the electrooxidation of thioridazine (TR) using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The determination conditions, such as accumulation time, pH of solution, and modifier amount were optimized. The mechanism of the electrooxidation process on the surface of the modified electrode was studied electrochemically. A linear range of 0.1–36.0 µM with detection limit of 65.0 nM was obtained for TR. In a mixture containing TR and olanzapine (OLZ), the DPV peaks of two compounds can be well separate from each other with a potential difference of 425 mV. Finally, this method was successfully applied to determinate the TR content in real samples.     

Nanodiamond Decorated with Silver Nanoparticles as a Sensitive Film Modifier in a Jeweled Electrochemical Sensor: Application to Voltammetric Determination of Thioridazine

Nanodiamond? graphite (NDG) decorated with Ag nanoparticles (AgNPs‐NDG) was prepared and used to construct a novel sensitive sensor for the voltammetric determination of thioridazine (TR). The results indicate a remarkable increase in the oxidation peak currents together with a negative shift in the oxidation peak potentials, in comparison to the bare pyrolytic graphite electrode. Remarkable enhancement in microscopic area of the electrode along with strong adsorption of TR on the surface of the modified electrode resulted in a considerable increase in the peak current of TR. The surface morphology and the nature of the composite film deposited on PGE were characterized by scanning electron microscopy, atomic force microscopy, cyclic voltammetry and electrochemical impedance spectroscopy. Experimental variables, such as the deposited amount of the modifier suspension, pH of the supporting electrolyte, the accumulation potential and time are optimized by monitoring the CV responses of TR. Under the optimal conditions, the modified electrode showed a wide linear response to the concentration of TR in the range of 0.08–100 µM with a detection limit of 0.01 µM. The prepared modified electrode showed several advantages: simple preparation method, high stability and uniformity in the composite film, high sensitivity, long‐term stability and remarkable voltammetric reproducibility in response to TR. The modified electrode can be successfully applied for accurate determination of trace amounts of TR in pharmaceutical and clinical preparations.     

优化金属辅助法腐蚀液组分制备多孔硅

金属辅助化学腐蚀法可以在无外加电路的条件下,在40%HF/30%H2O2/乙醇的混合溶液中完成多孔硅的制备,该方法简单快速。本文研究了金属辅助法腐蚀液体系各组分(HF、H2O2、乙醇)含量对多孔硅表面的SiHx成分和多孔层结构的影响,根据Si-H和Si-O的红外吸收峰强度的变化曲线优化了腐蚀液体系中各组分含量。在腐蚀液各组分体积比为V40%HF∶V30%H2O2∶V乙醇=2∶2∶1和腐蚀时间为4 min的条件下制备了形貌均匀、化学活性(SiHx成分)和多孔结构稳定性较好的多孔硅,并对金属辅助法与阳极蚀刻法制得的两种多孔硅进行比较,结果显示金属辅助法制备的多孔硅的化学活性和稳定性在后续的生物技术应用中具有明显的优越性。     

Ni3S2 Supported on Porous Ball‐milled Silicon,a Highly Selective Electrochemical Sensor for Glucose Determination

In this work, an electrochemical sensor based on Ni₃S₂ nanoparticles supported on porous ball‐milled silicon was fabricated for measuring glucose. At first, the glassy carbon electrode (GCE) surface was modified by Ni₃S₂ nanoparticles supported on a porous ball‐milled silicon substrate. To characterize the modified electrode, N₂ adsorption‐desorption isotherms and BHJ, transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy‐dispersive X‐ray spectroscopy (EDX), elemental mapping and X‐ray diffraction (XRD) were used. In the following, the effective parameters on the sensor response such as pH, NaOH concentration, catalyst concentration, applied potential, and rotational speed of the electrode were optimized using cyclic voltammetric (CV) and hydrodynamic amperometric methods. Under the optimal conditions, the calibration curve was plotted using the hydrodynamic amperometric method. Three linear regions were obtained from 0.5–134, 134–1246, and 1246–3546 μM, with a detection limit of 0.2 μM for glucose. Finally, the proposed method was used for measuring glucose levels in human blood serums.     

Boosting the Dynamic Range for Electrochemical Sensing of Hydrogen Peroxide by Enhanced Integration of Pd Nanoparticles in 3D Porous Si Framework

Three-dimensional porous silicon framework (3D-pSi) integrated with various nanostructures is highly potential for functional devices usage such as micro fuel cells or sensing chips. For noble metal deposition in highly directional Si nanowire array or porous Si with large aspect ratios, one difficulty is the restriction on the depth of deposition available. Herein, we would like to introduce a facile route to enhance the integration of Pd nanoparticles with anisotropic Si porous structure. By converting Si nanowire array into 3D-pSi, the surface coverage of Pd nanoparticles is effectively improved as shown by scanning electron micrographs and cross-sectional element mapping data. The relative electrochemical active surface area is increased by 3.5 folds. In order to demonstrate the merits brought by this morphological evolution, the electrochemical sensing devices are prepared for detecting H₂O₂ in PBS solution. As shown by differential pulse voltammetry, the upper limit of linear range of detection can be raised from 6.30 mM to 14.95 mM. This approach may indicate an alternative for boosting the performance of future sensing chips with progressively limited die area, especially attractive for those scenarios where large dynamic range is favourable.     

金属辅助化学刻蚀法制备硅纳米线及应用

金属辅助化学刻蚀是近些年发展起来的一种各向异性湿法刻蚀,利用该方法可以制备出高长径比的半导体一维纳米结构。 本文综述了金属辅助化学刻蚀法可控制备硅纳米线的最新进展,简要概述了刻蚀的基本过程与机制,重点阐述了基于不同模板的金属辅助化学刻蚀可控制备高度有序、高长径比的硅纳米线阵列的具体流程与工艺,并介绍了其在锂离子电池、太阳能电池、气体传感检测和仿生超疏水等方面的潜在应用,探讨了目前存在的问题及其今后的研究发展方向。     

Room-Temperature Ionic Liquid and Multi-Walled Carbon Nanotube Composite Modified Carbon-Ceramic Electrode as a Sensitive Voltammetric Sensor for Indomethacin

The electrochemical behavior of indomethacin on the surface of a carbon-ceramic electrode modified with multi-walled carbon nanotubes and an ionic liquid composite film is reported. The results show that the nano-structured film exhibited excellent enhancement effects on the electrochemical oxidation of indomethacin. The developed sensor presented a linear response to indomethacin over the concentration range from 1 to 50 µM with a detection limit of 0.26 µM. The proposed modified electrode was employed for the determination of indomethacin in biological and pharmaceutical samples using differential pulse voltammetry.     

Solid-state Electrochemical Sensor Based on a Cross-linked Copper(II)-doped Copolymer and Carbon Nanotube Material for Selective and Sensitive Detection of Monohydrogen Phosphate

A novel solid-state electrochemical sensor based on a newly synthesized cross-linked copper(II) doped-copolymer and carbon nanotube material was developed for the direct determination of monohydrogen phosphate ions (HPO₄²⁻). The synthesized copolymers were characterized by FTIR, XPS, TG/DTG-DTA and SEM techniques. The sensor had a Nernstian slope:-30.7±0.4 mV/decade, linear concentrations range: 1.0×10⁻⁶ - 1.0×10⁻¹ M, detection limit: 6.5×10⁻⁷ M, response time: 4 s and life time: 17 weeks. The sensor displayed constant potentials in the pH range 7.0-9.5. The sensor was successfully used as an indicator electrode in potentiometric titration and the direct determination of HPO₄ ²⁻ in water samples.     

Nanocellulose/Carbon Nanoparticles Nanocomposite Film Modified Electrode for Durable and Sensitive Electrochemical Determination of Metoclopramide

A novel electrochemical sensor based on nanocellulose‐carbon nanoparticles (NC‐CNPs) nanocomposite film modified glassy carbon electrode (GCE) is developed for the analysis of metoclopramide (MCP). Atomic force microscopy, scanning electron microscopy and electrochemical impedance spectroscopy were used to characterize the roughness, surface morphology and performance of the deposited modifier film on GCE. SEM image demonstrated that modifier nanoparticles are uniformly deposited on GCE, with an average size of less than 50 nm. The electrochemical behavior of MCP and its oxidation product is studied using linear sweep and cyclic voltammetry over a wide pH range on NC‐CNPs modified glassy carbon electrode. The results revealed that the oxidation of MCP is an irreversible and pH‐dependent process that proceeds in an adsorption‐controlled mechanism and results in the formation of a main oxidation product, which adsorbs on the surface of NC‐CNPs/ GCE. The modified electrode showed a distinctive anodic response towards MCP with a considerable enhancement (49 fold) compared to the bare GCE. Under the optimized conditions, the modified electrode exhibited a wide linear dynamic range of 0.06–2.00 µM with a detection limit of 6 nM for the voltammetric determination of MCP. The prepared modified electrode showed several advantages such as simple preparation method, high stability, reproducibility, and repetitive usability. The modified electrode is successfully applied for the accurate determination of trace amounts of MCP in pharmaceutical and clinical preparations.     

Incorporation of Tetrazolium Blue (TB)/Gold Nanoparticles (GNPs) into Carbon Paste Electrode: Application as an Electrochemical Sensor for the Sensitive and Selective Determination of Sotalol in Micellar Medium

The electrochemical oxidation of Sotalol (SOT) based on Tetrazolium Blue (TB)/gold nanoparticles (GNPs)‐modified carbon paste electrodes (CPE) have been studied in the presence of sodium lauryl sulphate (SLS). Cyclic voltammetry (CV), differential pulse voltammetry (DPV), chronoamperometry and electrochemical impedance spectroscopy (EIS) techniques have all been utilized within this study. GNPs and TB have a synergetic effect‐giving rise to highly improved electrochemical responses and provide an advantageous platform for the basis of an electrochemical sensor with excellent performance. The experimental parameters, electrodeposition time, pH and scan rate have all been examined and optimized. The sensing of SOT via DPV is found to exhibit a wide linear dynamic range of 1.0×10⁻⁷–7.5×10⁻⁴ M in pH 2. LOD and LOQ were calculated and found to correspond to 2.5×10⁻⁸ M and 8.3×10⁻⁸ M, respectively. The suggested sensor has been used successfully for SOT determination in pharmaceutical samples and human urine as real samples. Satisfactory recoveries of analyte from these samples are demonstrated indicating that the suggested sensor is highly suitable for clinical analysis, quality control and a routine determination of SOT in pharmaceutical formulations.     

藉铋-亚硝基R盐-结晶紫反应高灵敏分光光度测定痕量铋

本文提出了一个超高灵敏测定铋的分光光度方法。缔合物的吸收峰位于600um，表观摩尔吸光系数ε600＝3．0×109L·mol’·cm－1，铋浓度在0～200ng／L范围内遵守比耳定律。本法用于水样和合成试样中痕量铋的测定，结果较满意。对缔合物组成与显色机理进行了初步讨论。     

Selective and Sensitive Determination of Uranyl Ions in Complex Matrices by Ion Imprinted Polymers‐Based Electrochemical Sensor

We report on the design of a UO₂²⁺‐selective electrode based on the use of UO₂²⁺ imprinted polymer nanoparticles (IP‐NPs), and its application for the differential pulse adsorptive cathodic stripping voltammetry determination of uranyl ions. A carbon paste electrode was modified with the IP‐NPs, and differential pulse adsorptive cathodic stripping voltammetry was applied as the detection technique after open‐circuit sorption of UO₂²⁺ ions. The modified electrode responses to UO₂²⁺ was linear in the 0.1 µg L^?1 to 10 µg L^?1 and in the 0.01 mg L^?1 to 10 mg L^?1. The method detection limit of the sensor was 0.03 µg L^?1.     

Self‐Assembled Prussian Blue Nanoparticles Based Electrochemical Sensor for High Sensitive Determination of H2O2 in Acidic Media

In this paper, self‐assembled Prussian blue nanoparticles (PBNPs) on carbon ceramic electrode (CCE) were developed as a high sensitive hydrogen peroxide (H₂O₂) electrochemical sensor. The PBNPs film was prepared by a simple dipping method. The morphology of the PBNPs‐modified CCE was characterized by scanning electron microscopy (SEM). The self‐assembled PB film exhibited sufficient mechanical, electrochemical stability and high sensitivity in compare with other PB based H₂O₂ sensors. The sensor showed a good linear response for H₂O₂ over the concentration range 1 μM–0.26 mM with a detection limit of ca. 0.7 μM (S/N=3), and sensitivity of 754.6 mA M^?1 cm^?2. This work demonstrates the feasibility of self‐assembled PBNPs‐modified CCE for practical sensing applications.     

氧化钒/多孔硅/硅结构的微观形貌、纳米力学及温敏特性

采用电化学腐蚀法在硅基片表面形成多孔硅, 利用直流对靶反应磁控溅射方法在不同电流密度条件下制备的多孔硅样品表面上溅射沉积了VOx薄膜, 获得了氧化钒/多孔硅/硅(VOx/PS/Si)结构. 采用场发射扫描电镜(FESEM)观测多孔硅及VOx/PS/Si结构的微观形貌, 采用纳米压痕仪器测量VOx/PS/Si结构的纳米力学特性, 通过电阻-功率曲线分析研究其温度敏感特性. 实验结果表明, 在40和80 mA·cm-2电流密度下制备多孔硅的平均孔径分别为18和24 nm, 用显微拉曼光谱法(MRS)测量其热导率分别为3.282和1.278 kW·K-1; VOx/PS/Si结构的电阻随功率变化的平均速率分别为60×10⁹和100×10⁹ Ω·W-1, VOx/PS/Si结构的显微硬度分别为1.917和0.928 GPa. 实验结果表明, 多孔硅的微观形貌对VOx/PS/Si结构的纳米力学及温敏特性有很大的影响, 大孔隙率多孔硅基底上制备的VOx/PS/Si 结构比小孔隙率多孔硅基底上制备的具有更高的温度灵敏度, 但其机械稳定性也随之下降.     

Sensitive and Selective Electrochemical Sensor Based on Molecularly Imprinted Polypyrrole Hybrid Nanocomposites for Tetrabromobisphenol A Detection

Abstract

A sensitive and selective electrochemical sensor based on electropolymerized molecularly imprinted polypyrrole and gold nanoparticles–multiwalled carbon nanotubes (AuNPs–MWCNTs) hybrid nanocomposites was developed for the determination of tetrabromobisphenol A (TBBPA). A glassy carbon electrode (GCE) was modified with MWCNTs, and the AuNPs–MWCNTs/GCE was prepared by an electrodeposition method in HAuCl₄ solution. The AuNPs–MWCNTs nanocomposite showed high electrocatalytic activity, good conductivity, and sufficient reactive sites for the direct electro-oxidation of TBBPA. The molecularly imprinted polymers (MIPs) as recognition elements were synthesized through in situ electro-polymerization of pyrrole as functional monomers in the presence of the TBBPA template molecules. Under the optimal conditions, the developed sensor exhibited good selectivity towards TBBPA compared with structural analogs, high sensitivity, and excellent producibility. The electrochemical responses of the sensor toward TBBPA were obtained in the linear range from 0.5?nM to 1?μM with a limit of detection equal to 0.24?nM at a signal-to-noise ratio of 3.     

Sensitive and Selective Determination of Phenylhydrazine in the Presence of Hydrazine at a Ferrocene Monocarboxylic Acid Modified Carbon Nanotube Paste Electrode

In the present paper, the use of a carbon paste electrode modified by ferrocene monocarboxylic acid (FMC) and carbon nanotubes prepared by a simple and rapid method was described. The modified electrode showed an excellent character for electrocatalytic oxidization of phenylhydrazine (PHZ) and hydrazine (HZ) with a 300 mV separation of both peaks. Differential pulse voltammetric peak currents of PHZ and HZ increased linearly with their concentrations at the range of 0.8 µM to 700 µM and 16 µM to 800 µM and the detection limits (3σ) were determined to be 0.42 µM and 14 µM, respectively.     

First Electrochemical Report for Simultaneous Determination of Norepinephrine,Tyrosine and Nicotine Using a Nanostructure Based Sensor

A carbon paste electrode was modified with ZnO nanorods and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,4′AAZCPE) to cause electrocatalysis of norepinephrine oxidation. It has been found that the oxidation of norepinephrine at the surface of modified electrode occurs at a potential of about 180 mV less positive than that of an unmodified carbon paste electrode. Square wave voltammetry (SWV) exhibits linear dynamic range from 1.0×10^?7 to 8.0×10^?5 M and a detection limit of 3.9×10^?8 M for norepinephrine. In addition, this modified electrode was used for simultaneous determination of norepinephrine, tyrosine and nicotine.     

Sensitive and Green Method for Determination of Chemical Oxygen Demand Using a Nano‐copper Based Electrochemical Sensor

Copper nanoparticles (nano‐Cu) were electrodeposited on the surface of glassy carbon electrode (GCE) potentiostatically at −0.6 V vs. Ag/AgCl for 60 s. The developed nano‐copper modified glassy carbon electrode (nano‐Cu/GCE) was optimized and utilized for electrochemical assay of chemical oxygen demand (COD) using glycine as a standard. The surface morphology and chemical composition of nano‐Cu/GCE were investigated using scanning electron microscope (SEM) and energy dispersive X‐ray spectrometer (EDX), respectively. The electrochemical behavior was investigated using linear sweep voltammetry (LSV) which is characterized by a remarkable anodic peak at ∼0.6 V, compared to bare GCE. This indicates that nano‐Cu enhances significantly the electrochemical oxidation of glycine. The effect of different deposition parameters, such as Cu²⁺ concentration, deposition potential, deposition time, pH, and scan rate on the response of the developed sensor were investigated. The optimized nano‐Cu/GCE based COD sensor exhibited a linear range of 15 to 629.3 ppm, and a lower limit of detection (LOD) of 1.7 ppm (S/N=3). This developed method exhibited high tolerance level to chloride ion (0.35 M chloride ion has minimal influence). The analytical utility of the prepared COD sensor was demonstrated by investigating the COD recovery (99.8±4.3) and the assay of COD in different water samples. The results obtained were verified using the standard dichromate method.     

Zinc Oxide Nanoparticle‐modified Glassy Carbon Electrode as a Highly Sensitive Electrochemical Sensor for the Detection of Caffeine

Zinc oxide nanoparticles (ZnO NPs ) were prepared by a simple, convenient, and cost‐effective wet chemical method using the biopolymer starch. The prepared ZnO NPs were characterized by X‐ray diffraction (XRD ), scanning electron microscopy (SEM ), energy‐dispersive X‐ray (EDX ), Fourier transform infrared (FT‐IR ), and UV ‐visible spectroscopic techniques. The average crystallite size calculated from XRD data using the Debye–Scherer equation was found to be 15 nm. The electrochemical behavior of caffeine (CAF ) was studied using a glassy carbon electrode (GCE ) modified with zinc oxide nanoparticles by cyclic voltammetry (CV ) and differential pulse voltammetry (DPV ). Compared to unmodified GCE , ZnO NPs‐ modified GCE (ZnO NPs MGCE ) exhibited excellent electrocatalytic activity towards CAF oxidation, which was evident from the increase in the peak current and decrease in the peak potential. Electrochemical impedance study suggested that the charge‐transfer capacity of GCE was significantly enhanced by ZnO NPs . The linear response of the peak current on the concentrations of CAF was in the range 2–100 μM . The detection limit was found to be 0.038 μM. The proposed sensor was successfully employed for the determination of CAF in commercial beverage samples.     

Manganese Oxide Nanoparticles/Reduced Graphene Oxide as Novel Electrochemical Platform for Immobilization of FAD and its Application as Highly Sensitive Persulfate Sensor

In this study, manganese oxide nanoparticles/reduced graphene oxide(MnOxNPs/rGO) was used as support for strong immobilization of flavin adenine dinucleotide(FAD). A thin film of rGO cast on the electrode surface, followed by performing electrodeposition of MnOxNPs at applied constant potential of +1.4 V vs. Ag/AgCl for 200 s. Finally, FAD was electrodeposited onto the rGO/MnOxNPs film by potential cycling between 1.0 to ?1.0 V in solution containing 1 mg ml^?1 FAD. Electrochemical properties and catalytic activity of GCE/rGO‐MnOxNPs/FAD toward persulfate (S₂O₈^2?) reduction was investigated. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 0.1 μM–2 mM, 90 nM and 125.8 nA/μM, respectively, using hydrodynamic amperometry technique.