Electropolymerization of Metallophthalocyanines Carrying Redox Active Metal Centers and their Electrochemical Pesticide Sensing Application

In this study, modified electrodes were constructed with the electropolymerization of metallophthalocyanines (MPcs) carrying redox active metal cations and electropolymerizable substituents. Then these electrodes were tested as selective and sensitive electrochemical pesticide sensors. Incorporation of the redox active Co(II) (CoPc(MOR‐NAF)), Cl–Mn(III) (MnPc(MOR‐NAF)), and Ti(IV)O (TiOPc(MOR‐NAF)) metal cations into Pc cavity increased the redox activity of Pc ring. Moreover, redox active and electropolymerizable 5‐{[(1E)‐(4‐morpholin‐4‐ylphenyl)methylene]amino}‐1‐naphthoxy substituents (MOR‐NAF) on the Pc ring triggered coating of the complexes on the electrode surface with the electropolymerization reactions. Therefore, modified electrodes GCE/MPc(MOR‐NAF) were constructed with the electropolymerizations of MPcs. These electrodes illustrated reasonable redox activity and conductivity for the potential applications in different fields of the electrochemical technologies. Pesticide sensing measurements indicated that changing the metal center of the complexes significantly altered their sensing activities. Among the complexes, GCE/CoPc(MOR‐NAF) electrode behaved as the most sensitive and selective electrode and it sensed the parathion with good selectivity and sensitivity. GCE/CoPc(MOR‐NAF) electrode showed a wider linear range (0.075‐5.75 μmoldm⁻³) and smaller LOD (0.025 μmoldm⁻³) and higher sensitivity (3.46 Acm⁻²M⁻¹) for the parathion sensing. Although GCE/TiOPc(MOR‐NAF) electrode also sensed the parathion with a high sensitivity, its selectivity was poor and the linear range of this sensing was very narrow. Differently GCE/Cl–MnPc(MOR‐NAF) electrode only sensed eserine with reasonably sensitivity.     

Square Wave‐Anodic Stripping Voltammetric Determination of Copper at a Bismuth Film/Glassy Carbon Electrode Using 3‐[(2‐Mercapto‐Vinyl)‐Hydrazono]‐ 1,3‐Dihydro‐Indol‐2‐One

This study reports a highly sensitive electrochemical sensor based on Bi film modified glassy carbon electrode (BiF/GCE) for total determination and speciation trace concentrations of copper(II) ions in environmental water samples. Square wave‐adsorptive anodic stripping voltammetric (SW‐ASV) experiment was performed for monitoring selective accumulation of copper(II) with reagent 3‐[(2‐mercapto‐vinyl)‐hydrazono]‐1,3‐dihydro‐indol‐2‐one (MHDI) at pH 9–10. The mechanism of the electrode reaction of Cu²⁺‐MHDI complex was safely assigned. The sensor exhibited a wide linear range (3.22×10⁻⁹–2.0×10⁻⁷ mol L⁻¹) with lower limits of detection (LOD) and quantitation (LOQ) of 9.6×1⁻¹⁰ and 3.22×10⁻⁹ mol L⁻¹, respectively (R²=0.9993). The proposed sensor exhibited interference from active metal ions e. g. Cd, Hg. The performance of the proposed method was compared successfully with most of the reported methods and comparable efficiencies were obtained. The analytical utility of the proposed SW‐ASV method has been successfully validated for trace analysis of copper(II) in environmental water samples. The method offers a precise, accurate approach with good reproducibility, robustness, ruggedness, and cost effectiveness.     

New electrode material GCE/AgNPs-D3 as an electrochemical sensor used for the detection of thallium ions

Optimal working parameters for the innovative electrode GCE/AgNPs-D3 were determined and the selectivity was assessed. The stripping anodic peak current of thallium characterized in linearity over range from 4.9 ⋅ 10⁻⁸ to 4.9 ⋅ 10⁻⁷ mol ⋅ dm⁻³, with LOD = 7.16 ppb (3.5 ⋅ 10⁻⁸ mol ⋅ dm⁻³). Furthermore, the new electrode showed more than sevenfold improvement in the thallium current signal compared to the unmodified electrode GCE. High selectivity was achieved using EDTA disodium salt as a complexing agent for other metals.     

Simultaneous Electrochemical Detection of Co(II) and Cu(II) by 1‐Diazo‐2‐Naphthol‐4‐Sulfonic Acid/MWCNTs Modified Electrode

This work describes a simple preparation of 1‐diazo‐2‐naphthol‐4‐sulfonic acid (1,2,4‐acid) and multiwalled carbon nanotubes (MWCNTs) modified glassy carbon electrode (GCE) for the simultaneous detection of Co(II) and Cu(II). MWCNTs, with their good conductivity and large surface area, were drop‐casted onto the surface of the GCE prior to the electrodeposition of 1,2,4‐acid, a metal chelating agent. Co(II) and Cu(II) were simultaneously measured by differential pulse anodic stripping voltammetry (DPASV) in a batch system. Under optimum conditions, the linear range of Co(II) was between 0.10 and 2.5 μg mL⁻¹ with an LOD of 80 ng mL⁻¹. Two linear ranges were obtained for Cu(II), 0.0050 to 0.030 μg mL⁻¹ and 0.040 to 0.25 μg mL⁻¹,with an LOD of 2.4 ng mL⁻¹. The method offered a high operational stability for up to 52 measurements (RSD=3.4 % for Co(II) and 2.6 % for Cu(II)) and good reproducibility (RSD=1.2 % for Co(II) and 1.7 % for Cu(II)). In the simultaneous detection of Co(II) and Cu(II), there was no effect from common interferences found in wastewater. The method was successfully applied in real water samples with good recoveries (88.2±0.8 to 102.0±0.8 % for Co(II) and 96.5±0.4 to 103.8±0.9 % for Cu(II)) and the results were in good agreement with those obtained from inductively coupled plasma optical emission spectrometry (ICP‐OES) (P >0.05).     

Electrode Modification through Click Chemistry Using Ni and Co Alkyne Phthalocyanines for Electrocatalytic Detection of Hydrazine

This work reports on the development of sensors for the detection of hydrazine using glassy carbon electrodes (GCE) modified with phthalocyanines through click chemistry. Tetrakis(5‐hexyn‐oxy) cobalt(II) phthalocyanine (complex 2 ) and tetrakis(5‐hexyn‐oxy) nickel(II) phthalocyanine (complex 3 ) were employed as electrode modifiers for hydrazine detection. The GCE was first grafted via the in situ diazotization of a diazonium salt, rendering the GCE surface layered with azide groups. From this point, the 1, 3‐dipolar cycloaddition reaction, catalysed by a copper catalyst was utilised to “click” the phthalocyanines to the surface of the grafted GCE. The modified electrodes were characterized by scanning electrochemical microscopy, X‐ray photoelectron spectroscopy and cyclic voltammetry. The electrografted CoP 2 ‐clicked‐GCE and NiP 3 ‐clicked‐GCE exhibited electrocatalytic activity towards the detection of hydrazine. The limit of detection (LoD) for the CoPc‐GCE was 6.09 μM, while the NiPc‐GCE had a LoD of 8.69 μM. The sensitivity was 51.32 μA mM⁻¹ for the CoPc‐GCE and 111.2 μA mM⁻¹ for the NiPc‐GCE.     

Electrochemical Behaviour of Poly(benzopyrene) Films Doped with Eriochrome Black T as a Pb2+‐Sensitive Sensors

Poly(benzopyrene) films were electrosynthesized on glassy carbon disk electrodes from benzo(a)pyrene by cyclic voltammetry in the presence of eriochrome black T, which forms strong complexes with lead ions. In consequence, by conditioning the films in high concentration of lead (0.1 mol dm^?3 Pb(NO₃)₂) potentiometric sensitivity to lead ions down to 10^?5 mol dm^?3 Pb²⁺ was induced, and a novel type of lead‐sensitive electrode was obtained. The electrode is characterized by high stability of the potential readouts, good reproducibility of the calibration curves as well as a minor hysteresis effects. The performance of our lead‐sensitive electrode was favourable compared to PEDOT and PPy‐based electrodes doped with eriochrome black T. We conclude that poly(benzopyrene) doped with eriochrome black T is a new electroactive material that may be applied in sensor technology.     

Stripping Voltammetric Determination of Methyl Parathion at Activated Carbon Nanopowder Modified Electrode

An activated carbon nanopowder modified glassy carbon electrode (AC-GCE) was constructed for the sensitive determination of methyl parathion by adsorptive differential pulse anodic stripping voltammetry. The simple and rapid modification procedure included only drop-coating the electrode surface with a laponite stabilized activated carbon nanopowder suspension and drying. The modifier high adsorption ability, combined with its large electroactive surface area allowed a 30-fold signal increase to be achieved, compared to bare GCE. Under optimized experimental conditions (activated carbon to laponite ratio, pH and accumulation time), the AC-GCE exhibited a linear response to methyl parathion in two concentration ranges: from 0.01 μmol L⁻¹ to 1 μmol L⁻¹ and from 1 μmol L⁻¹ to 6 μmol L⁻¹. The LOD of 2.5 nmol L⁻¹ (S/N=3) achieved fitted with regulatory norms. It was demonstrated that the as-prepared AC-GCE is suitable for routine real samples analysis.     

Selective Electroanalysis of Ascorbic Acid Using a Nickel Hexacyanoferrate and Poly(3,4‐ethylenedioxythiophene) Hybrid Film Modified Electrode

The mixed‐valent nickel hexacyanoferrate (NiHCF) and poly(3,4‐ethylenedioxythiophene) (PEDOT) hybrid film (NiHCF‐PEDOT) was prepared on a glassy carbon electrode (GCE) by multiple scan cyclic voltammetry. The films were characterized using atomic force microscopy, field emission scanning electron microscopy, energy dispersive spectroscopy, X‐ray diffraction, and electrochemical impedance spectroscopy (AC impedance). The advantages of these films were demonstrated for the detection of ascorbic acid (AA) using cyclic voltammetry and amperometric techniques. The electrocatalytic oxidation of AA at different electrode surfaces, such as the bare GCE, the NiHCF/GCE, and the NiHCF‐PEDOT/GCE modified electrodes, was determined in phosphate buffer solution (pH 7). The AA electrochemical sensor exhibited a linear response from 5×10⁻⁶ to 1.5×10⁻⁴ M (R²=0.9973) and from 1.55×10⁻⁴ to 3×10⁻⁴ M (R²=0.9983), detection limit=1×10⁻⁶ M, with a fast response time (3 s) for AA determination. In addition, the NiHCF‐PEDOT/GCE was advantageous in terms of its simple preparation, specificity, stability and reproducibility.     

Over‐Oxidized Poly (Phenol Red) Film Modified Glassy Carbon Electrode for Anodic Stripping Voltammetric Determination of Ultra‐Trace Antimony (III)

In this study, we introduce a very sensitive and selective method for the differential pulse anodic stripping determination of Sb(III) ion on the over‐oxidized poly(phenol red) modified glassy carbon electrode (PPhRed_ox/GCE) in 0.1 mol L^‐1 HCl medium. The formation of both poly(phenol red) and over‐oxidized poly(phenol red) film on the electrode surfaces were characterized by electrochemical impedance spectroscopy, X‐ray photoelectron spectroscopy and scanning electron microscopy techniques. An anodic stripping peak of Sb(III) was observed at 0.015 V on the PPhRed_ox/GCE. Higher anodic stripping peak current of Sb(III) was obtained at PPhRed_ox/GCE compared with both bare GCE and poly(phenol red) film modified GCE (PPhRed/GCE). The calibration graph consisted of two linear segments of 0.044 ‐ 1.218 μg L⁻¹ and 3.40 – 18.26 μg L⁻¹ with a detection limit of 0.0075 μg L⁻¹. The proposed over‐oxidized polymer film modified electrode was applied successfully for the analysis of antimony in different spiked water samples. Spiked recoveries for water samples were obtained in the range of 93.0–103.0%. The accuracy of the method was also verified through the analysis of standard reference materials (SCP SCIENCE‐EnviroMAT™ EP−L‐2).     

Effect of detonation nanodiamonds on the electrocatalytic activity of asymmetric cobalt phthalocyanine: Covalent versus non-covalent linking

We report on the effect of detonation nanodiamonds (DNDs) on electrocatalytic properties of an asymmetrically substituted cobalt phthalocyanine (CoPc). The incorporation of DNDs onto cobalt phthalocyanine enhances its electrochemical behaviour. An asymmetrical CoPc alone, when π-π stacked (CoPc-DNDs(ππ)) or covalently linked (CoPc@DNDs) to DNDs is used to modify a glassy carbon electrode (GCE) for the electrocatalytic detection of hydrazine. In addition, the GCE was modified by sequentially adding CoPc and DNDs onto its surface, represented as GCE/CoPc-DNDs(seq) when CoPc is placed before DNDs on the electrode and GCE/DNDs-CoPc(seq) when DNDs are placed before CoPc, where seq represents sequential. The obtained catalytic rate for the detection of hydrazine on GCE/CoPc@DNDs was 9.3×10⁴ M⁻¹.s⁻¹ with a limit of detection as 0.33 μM. GCE/CoPc@DNDs gave better electrocatalytic activities when compared to its counterparts.     

Electrochemical and Spectroelectrochemical Analysis of 4‐(4‐(5‐Phenyl‐1,3,4‐oxadiazole‐2‐yl)phenoxy)‐Substituted Cobalt(II), Lead(II) and Metal‐Free Phthalocyanines

Electrochemical and spectroelectrochemical analyses of 4‐(4‐(5‐phenyl‐1,3,4‐oxadiazole‐2‐yl)phenoxy)‐substituted metal‐free phthalocyanine ( H₂Pc ( 1 )) and metallated phthalocyanines ( PbPc ( 2 ) and CoPc ( 3 )) were performed in solution. Voltammetric characterizations of the phthalocyanine complexes were investigated by using cyclic voltammetry and square wave voltammetry techniques. CoPc ( 3 ) gave common metal and ring based electron transfer reactions; however they split due to the aggregation. Although PbPc ( 2 ) illustrated reversible reduction processes during the voltammetric measurements, it was de‐metallized and thus turned to the metal free phthalocyanine during repetitive voltammetric cycles and in situ spectroelectrochemical measurements.     

Simultaneous Determination of Nitrophenol Isomers Based on β‐Cyclodextrin Functionalized Reduced Graphene Oxide

β‐CD modified reduced graphene oxide (RGO) sheets have been prepared and characterized by TEM, AFM, IR, EIS and CVs. In comparison with bare glass carbon electrode (GCE) and RGO modified GCE, CD‐RGO/GCE showed much higher peak currents to the reduction of nitrophenol isomers (NPs), attributed to the larger specific surface area of RGO and high quantities of host–guest recognition sites. Three pairs of redox peaks are observed on the CVs of CD‐RGO for p‐NP (0.3 V), o‐NP (?0.2 V) and m‐NP (0.05 V), separating well with each other. Under the optimized condition, the anodic peak currents were linear over ranges around 1–10 mg dm^?3 for p‐NP, 1–9 mg dm^?3 for o‐NP and 1–6 mg dm^?3 for m‐NP, with the detection limits of 0.05 mg dm^?3, 0.02 mg dm^?3 and 0.1 mg dm^?3, respectively. Thus, the CD‐RGO is expected to be a promising sensor material for detecting trace NPs in waste water.     

New Electrode Material GCE/AgNPs-LS/Hg Based on Nanosilver Produced with the Use of Biopolymers

A method of producing nanosilver by using lignosulfonic acid derivative and a new method of the obtained AgNPs-LS electrode material for developing a chemically modified GCE/AgNPs-LS/Hg electrode is presented. The data demonstrate that the modified electrode shows enhanced performance in determining Tl⁺ ions in comparison to unmodified electrode GCE. The stripping anodic peak current of thallium characterized in linearity over its concentration range from 1.22 ⋅ 10⁻⁸ to 1.15 ⋅ 10⁻⁷ mol dm⁻³, with detection limit 4.6 ⋅ 10⁻⁹ mol dm⁻³. It is assumed that the novel AgNPs-LS/Hg²⁺ complex is suitable for preparing functionalized nanostructured material and can be used as an electrochemical sensing platform for heavy metals.     

Preparation of Organophilic Nanohybrid Kaolinite and Application to the Electrochemical Detection of Organic Pesticide

Novel organophilic nanohybrid materials (K‐TDD) were obtained by the grafting of 1,2‐tetradecanediol (TDD) onto the surface of kaolinite (K). XRD, IR, TGA‐DTG, and SEM characterization showed that TDD grafting results in a partial exfoliation of kaolinite layers. This material was used to modify a glassy carbon electrode (GCE/K‐TDD) and applied for the trace analysis of methyl parathion (MP). The signal of MP recorded on GCE/K‐TDD was more intense compared to the unmodified GCE or to one modified with a film of natural kaolinite. Several parameters that can affect the stripping response were systematically investigated to optimize the sensitivity of the organokaolinite‐modified electrode. A linear calibration curve for MP was obtained in the concentration range from 2×10⁻⁶ to 14×10⁻⁶ mol .L⁻¹ in acetate buffer (pH 6), giving a detection limit of 9×10⁻⁸ mol .L⁻¹. The sensitivity of the method was found to be 2.42 μA/μM for the range of concentrations that gives a linear calibration curve. The electrode was shown to be very stable, with the electrochemical response of MP decreasing by only 1.5 % after a series of nine measurements. The interference of various inorganic ions and organic compounds likely to influence the stripping determination of the MP were also examined. The results showed that the GCE/K‐TDD electrode was effective in solutions containing interfering species and could be applied for the quantification of MP pesticide in natural water.     

Self‐Assembled Monolayers of Cobalt and Iron Phthalocyanine Complexes on Gold Electrodes: Comparative Surface Electrochemistry and Electrocatalytic Interaction with Thiols and Thiocyanate

The self‐assembling of the octa(hydroxyethylthio)‐metallophthalocyanine {MOHETPc (M=Co and Fe)} complexes and their similar analogues, octabutylthiometallophthalocyanine {MOBTPc (M=Co and Fe)} complexes on gold electrodes are investigated. Comparative surface voltammetric insights into their distinct self‐assembling properties with respect to the passivation of Faradaic processes and surface coverages, including their solution electrochemistry, suggest different orientations and non‐cleavage of their C? S bonds. In the pH 2?9 range, the reversible [M^(III)Pc(?2)]⁺ / [M^(II)Pc(?2)] redox couples show potential shifts close to ?59 mV / pH. The gold electrodes modified with the SAMs of these species show electrocatalytic activity towards the oxidation of thiols (L ‐cysteine, homocysteine and penicillamine) and thiocyanate in acidic media with detection limits in the region of 10^?7–10^?6 mol dm^?3. These monolayers are stable and easily reproducible.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

Simultaneous multielement‐specific detection of a novel glutathione–arsenic–selenium ion [(GS)2AsSe]− by ICP AES after micellar size‐ exclusion chromatography

In order to confirm the solution structure of [(GS)₂AsSe]⁻ (GS = glutathione), we have investigated the retention behaviour of a [(GS)₂AsSe]⁻/oxidized glutathione (GSSG) mixture on a Sephadex G‐25 (SF) column with Tris buffers (0.1 mol dm⁻³, pH 8.0) containing ­various surfactants at concentrations above the critical micellar concentration (CMC): hexadecyltrimethlammonium bromide (HDTAB; 30, 40 and 50 mmol dm⁻³); dodecyltrimethylammonium bromide (DDTAB; 50 mmol dm⁻³); and sodium lauryl sulfate (SLS; 50 mmol dm⁻³). ­An inductively coupled plasma atomic emission spectrometer (ICP AES) provided simultaneous on‐line detection of arsenic, selenium and ­sulfur in the column effluent. The chromatographic retention behaviour was used to investigate the association of both compounds with the positively charged micelles (HDTAB and DDTAB mobile phases). The relative strength of association with the micelles provided insight into the effective negative charge on [(GS)₂AsSe]⁻ and GSSG. The chromatograms obtained with 50 mmol dm⁻³ HDTAB indicated that two glutathione molecules are associated with the elution of an arsenic–selenium compound. Combined, these chromatographic data strongly support the spectroscopically derived solution structure of [(GS)₂AsSe]⁻. Copyright ­© 2000 John Wiley & Sons, Ltd.     

Electrochemical Sensor‐Based Ruthenium Nanoparticles on Reduced Graphene Oxide for the Simultaneous Determination of Ethinylestradiol and Amoxicillin

The composite material of reduced graphene and Ru nanoparticles (rGO/RuNP) was obtained by electrochemical oxidation of ruthenium nanoparticles immobilised on the glassy carbon electrode (GCE) surface and used for simultaneous electroanalysis of drugs. There are many discussions in the scientific community about the decrease in therapeutic efficacy of contraceptives when associated with antibiotics. The antibiotic effect of the antagonist can increase the contraceptive excretion levels in urine, indicating a reduction in the body and thus a decrease in the desired effect. Using the DPV technique, it was possible to quantify ethinylestradiol (EE2) and amoxicillin (AMX) with a linear response range, 5.50x10⁻⁸ – 1.20x10⁻⁶ mol L⁻¹, and LOD, 2.04 nmol L⁻¹ and 1.63 nmol L⁻¹, respectively. The results for the electrochemical behaviour of EE2 and AMX using GCE/rGO/RuNP were compared with GCE/rGO and GCE. The GCE/rGO/RuNP showed greater stability and separation anodic peak currents, suitable for the quantification of organic molecules in samples of environmental interest, as well as clinical and food samples.     

Interaction of dimethyltin(IV) dichloride with 5′‐IMP and 5′‐UMP

The formation constants of the species formed in the systems H⁺ + dimethyltin(IV) + 5′‐IMP and 5′‐UMP, H⁺ + 5′‐IMP and H⁺ + 5′‐UMP have been determined in aqueous solution in the pH range 1.5–9.5 at constant temperature (25 °C) and constant ionic strength (0.1 mol dm⁻³ NaClO₄), using spectrophotometric and potentiometric techniques. ¹H and ³¹P NMR investigations in aqueous solution confirmed the species formation. The precipitated complexes of IMP and UMP by Me₂Sn(IV)²⁺ at low pH values were characterized by elemental analysis and FTIR spectroscopy methods, the bonding sites of the ligands were determined and ruled out purine and pyrimidine moieties (N‐7 and N‐1 in IMP and N‐3 in UMP, respectively) while a bidentated coordination of the phosphate group is concluded in both cases. Finally, the experiments revealed the existence of complexes with trigonal bipyramidal structures that is in agreement with similar systems resulted previously. Copyright © 2008 John Wiley & Sons, Ltd.     

In Situ Scanning Tunneling Microscopy of Cobalt‐Phthalocyanine‐Catalyzed CO2 Reduction Reaction

We report a molecular investigation of a cobalt phthalocyanine (CoPc)‐catalyzed CO₂ reduction reaction by electrochemical scanning tunneling microscopy (ECSTM). An ordered adlayer of CoPc was prepared on Au(111). Approximately 14 % of the adsorbed species appeared with high contrast in a CO₂‐purged electrolyte environment. The ECSTM experiments indicate the proportion of high‐contrast species correlated with the reduction of Co^IIPc (?0.2 V vs. saturated calomel electrode (SCE)). The high‐contrast species is ascribed to the CoPc‐CO₂ complex, which is further confirmed by theoretical simulation. The sharp contrast change from CoPc‐CO₂ to CoPc is revealed by in situ ECSTM characterization of the reaction. Potential step experiments provide dynamic information for the initial stage of the reaction, which include the reduction of CoPc and the binding of CO₂, and the latter is the rate‐limiting step. The rate constant of the formation and dissociation of CoPc‐CO₂ is estimated on the basis of the in situ ECSTM experiment.