Tailoring Mesopores in Monolithic Macroporous Silica for HPLC

Mesopore formation in silica gels having continuous macropores has been investigated. The macroporous wet silica gel prepared by the sol‐gel process including phase separation was aged in a basic solvent making use of hydrolysis of urea in a closed condition. The mesopore structure was finally obtained by subsequent evaporation drying of solvent and heat‐treatment at 600°C for 2 h. The dissolution‐reprecipitation kinetics at the interfaces between wet gel skeletons and an external solvent affected the size and volume of pores formed within the skeletons. Below 120°C, mesopores suitable for various chromatographic applications have been formed typically within 24 h. On the other hand, at 200°C, the pore size attained the macropore dimensions (>50 nm), and the whole macroporous morphology was significantly modified.     

Ethylene Polymerization by Metallocene Catalysts Supported over Siliceous Materials with Bimodal Pore Size Distribution

Summary: As known, the pore structure of the catalytic support plays a decisive role during the polymerization reactions determining intra-particle mass and heat transport phenomena. In this work, several ethylene polymerizations have been carried out by using as catalytic support different mesostructured materials with unimodal and bimodal pore size distributions in order to evaluate the influence of this pore size distribution on the catalytic behavior. Calcined mesoporous materials were impregnated with the catalytic system MAO/(nBuCp)₂ZrCl₂ and used for ethylene polymerization and ethylene/1-hexene copolymerizations, at 70 °C and 5 bar of ethylene pressure. Polyethylenes obtained were characterized by GPC, DSC and Crystaf. Results indicate that porous structure of the support has a significant influence on polymerization activity and polymer properties. Despite the catalyst bimodal pore size distribution, only ethylene/1-hexene copolymers presented a bimodal chemical composition distribution.     

超浸润形状记忆海绵的制备及油-水分离性能

基于反式 1,4-聚异戊二烯(TPI)的形状记忆性能, 以聚氨酯海绵为基底, 包覆TPI制备出了一种具有疏水超亲油特性的三维多孔形状记忆海绵. 由于这种海绵具有良好的形状记忆特性, 可以通过反复按压/恢复过程, 实现对海绵孔径在微米尺寸(约875 μm)与纳米尺寸(约450 nm)间可逆调控. 利用材料特殊的浸润特征及其可控的孔尺寸, 进一步研究了其在油-水分离中的应用. 研究结果表明, 微米尺寸大孔径海绵有利于对不相溶油-水混合物进行快速高效分离, 而纳米尺寸小孔径海绵则有利于对乳液混合物进行分离, 实现了同一材料同时满足不相溶油-水混合物及乳液体系的分离要求.     

Thermal and Structural Behavior of Palm Oil. Influence of Cooling Rate on Fat Crystallization

Summary: The effects of scanning rates (q = −0.5 °C/min to −50 °C/min) on the formation of the different phases occurring at low temperature of a palm oil are investigated by means of calorimetry and optical analysis. It is demonstrated that the cooling rates changed the polymorphism of triacylglycerols (TAGs). The centrifugation is used to separate the two fractions (olein and stearin) of palm oil. We show whereas the rate of centrifugation the separation is not effective. We obtained two fractions, a liquid fraction and a solid fraction which contains some liquid TAGs. It is observed that the solid fraction of palm oil is more sensitive to the effects of the cooling rates. By changing the cooling rate q, it appears threshold behaviour for q = −3 °C/min dividing the data discussion in two parts: for slow cooling rate and for fast cooling rate. At slow cooling rates, TAGs had more time to interact. Contrary at fast cooling rate, TAGs have not the time to be reorganised in more stable conformation. Micrographs revealed that the types of crystals observed were spherolites but some variations in crystal size appeared with the variation of cooling rate.     

Evaluation of silica from different vendors as the solid support of anion‐exchange chiral stationary phases by means of preferential sorption and liquid chromatography

Chromatographic performance of a chiral stationary phase is significantly influenced by the employed solid support. Properties of the most commonly used support, silica particles, such as size and size distribution, and pore size are of utmost importance for both superficially porous particles and fully porous particles. In this work, we have focused on evaluation of fully porous particles from three different vendors as solid supports for a brush‐type chiral stationary phase based on 9‐O‐tert‐butylcarbamoyl quinidine. We have prepared corresponding stationary phases under identical experimental conditions and determined the parameters of the modified silica by physisorption measurements and scanning electron microscopy. Enantiorecognition properties of the chiral stationary phases have been studied using preferential sorption experiments. The same material was slurry‐packed into chromatographic columns and the chromatographic properties have been evaluated in liquid chromatography. We show that preferential sorption can provide valuable information about the influence of the pore size and total pore volume on the interaction of analytes of different size with the chirally‐modified silica surface. The data can be used to understand differences observed in chromatographic evaluation of the chiral stationary phases. The combination of preferential sorption and liquid chromatography separation can provide detailed information on new chiral stationary phases.     

Inter-spherulitic/inner-spherulitic localization of PBSU during crystallization of PVDF in PVDF/PBSU blend

In this work, the miscibility effect on the localization of poly(butylene succinate) (PBSU) during the crystallization of PVDF in their blend has been investigated. After annealed at 200 °C and 240 °C, homogeneous and phase-separated structures can be obtained respectively, which was followed by isothermal crystallization at 141 °C. In the case of 200°C, PBSU tends to enrich in inner-spherulitic regions because of the excellent miscibility of the blend and the higher growth rate of PVDF crystals. When the specimen was annealed at 240 °C, phase separation produces PVDF and PBSU domains. Upon cooling to 141 °C, one part of PBSU is miscible with , while the other part of it remains as phase-separated domains due to the high viscosity and slow relaxation of them. The former accounts for the distribution of PBSU in inner-spherulitic regions. In the latter, however, phase-separated structures depress the diffusion of PVDF during its crystallization, leading to the lower magnitude of growth rate of spherulites. Both of them contribute to the localization of PBSU in inter-spherulitic regions. The distribution of PBSU among PVDF spherulites has been validated by long periods, pore size, and mechanical performance of the porous PVDF membranes.     

金属-有机框架材料孔结构的初步理论评估

金属-有机框架材料在气体吸附/分离方面具有广泛的应用, 因而引起国内外学者的广泛关注。本文以6种代表性的MOFs为例简单介绍了利用理论工具研究MOFs孔结构的方法。     

Thermal stability and nonisothermal crystallization of short fiber-reinforced poly(ether ether ketone) composites

The thermal stability of a short carbon-fiber-reinforced PEEK composite was assessed by thermogravimetry and by a Rheometrics dynamic analyzer. The results indicated that holding for 10 min at 380°C was a suitable melting condition to avoid the thermooxidative degradation under air. After proving that the heating rate of 50°C/min can be used to evaluate the crystallinity, a heating stage was used to prepare nonisothermally crystallized specimens using cooling rates from 1 to 100°C/min after melting at 400°C for 3 or 15 min. The degree of crystallinity and the melting behavior of these specimens were investigated by DSC at a heating rate of 50°C/min. The presence of three or four regions indicated that the upper melting temperature, T_m, changed with the crystallization temperature. The first region with the highest T_m, which corresponded to the cooling rate of 1°C/min, can be associated with the crystallization in regime II. There was a second region where T_m decreased as the amount of crystals formed in regime II decreased with increasing cooling rate from 5 to 20°C/min. The third region, a plateau region, corresponded to regime III condition in which the crystals were imperfect. In the fourth region, the cooling was so fast that crystallization was incomplete during the cooling for the melting condition of 400°C for 15 min. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2225–2235, 1998     

金属-有机框架材料孔结构的初步理论评估

金属-有机框架材料在气体吸附/分离方面具有广泛的应用,因而引起国内外学者的广泛关注。本文以6种代表性的MOFs为例简单介绍了利用理论工具研究MOFs孔结构的方法。     

聚合物整体固定相的制备及条件优化

采用无搅动原位聚合模式,在聚醚醚酮柱管中直接制备了聚合物整体固定相。通过扫描电镜观察到该整体固定相的孔径分布呈双峰模式,且孔结构均匀。用压汞法测定了该固定相的孔径分布、孔隙率及比表面积等参数,考察了致孔剂组成、聚合温度及交联剂含量等参数对固定相孔结构的影响,并对制备条件进行了优化。测定了流速与柱前压的关系,实验表明此整体固定相具有良好的通透性。通过对山羊血清和低聚核苷酸的分离分析,证明了所制备的整体固定相适合用于生物大分子的分离纯化。     

三维MXene多孔结构的构建与应用研究进展

MXene作为一种新型二维（2D）纳米材料以其独特的高导电性、高电化学表面活性等特性在多个领域引起了广泛关注。然而,MXene纳米片在自组装过程中出现的紧密堆叠现象导致比表面积急剧下降,降低了活性表面积,从而严重阻碍了它们在能源储存、电磁屏蔽、吸附等领域的潜在应用。构建三维多孔结构是解决MXene组装过程中自堆叠问题的一种有效途径,而且通过不同的组装方法可以实现对多孔宏观结构组成成分、孔径分布以及孔径大小的调控,使得MXene多孔材料在机械性能、电学性能以及光热转换性能等方面得到更好的调整,从而满足不同应用领域的需求。本综述以Ti₃C₂T_x MXene为主要研究材料总结了各种多孔MXene宏观结构的制备方法,讨论了其在电池/超级电容器、电磁屏蔽与吸收、海水淡化、光催化以及传感和环境修复等方面的应用,阐述了MXene多孔结构在各种应用中的贡献与意义,并针对MXene多孔结构的制备、结构调控和应用等方面的机遇和挑战作了论述。     

Polymerization of para-xylylene derivatives. VI. morphology of parylene N and parylene C films investigated by gas transport characteristics

Polychloro-p-xylylene (Parylene C) and poly-p-xylylene (Parylene N) films were synthesized in vacuum with and without the presence of 42 mtorr of argon at various deposition temperatures and three different dimer sublimation rates. Depending on the synthesis conditions, the morphology of the films can vary from a homogeneous (nonporous) structure to a heterogeneous (porous) structure. The transport coefficients of the gases He, O₂, N₂, and CO₂ through these films were measured at 25°C. The transport coefficients for both types of films vary with the deposition temperature and the dimer sublimation rate. The variation, however, cannot be solely explained by the change of crystallinity. Anomalous transport behavior is observed in the homogeneous, as-synthesized polymers of relatively high crystalline content (above 20–30%). In many cases the permeabilities and diffusivities increase despite an increase in crystallinity. The effects of crystallization induced by isothermal and solvent annealing on the transport coefficients of polymers of Parylene C are different from those of Parylene N synthesized with or without argon. The mean pore size and effective porosity of the porous films were calculated from gas permeation data. For Parylene C and Parylene N porous films synthesized without argon, increasing the dimer sublimation rate or decreasing the deposition temperature increases the mean pore size but decreases the effective porosity. For Parylene N porous films synthesized in the presence of argon, increasing the dimer sublimation rate or decreasing the deposition temperature results in a decrease in the mean pore size but an increase in the effective porosity. Overall, no appreciable change in transport coefficients is observed upon addition of an inert gas.     

Strength and elasticity of bimodal porous silica prepared from water glass

The bending strength and the Young’s modulus of bimodal porous silica gels having different porosity were evaluated. The porosity of the gel increased by aging the gel under basic conditions, and decreased with increasing the calcination temperature. The mesopores disappeared on calcination at 1,050 °C, whereas continuous macropores retained their morphology up to 1,050 °C for all the samples. Both the bending strength and the Young’s modulus of the bimodal porous silica gels were expressed as power-law functions of the bulk density, and no effect of bimodal pore structures on mechanical properties was observed. We also found linear correlation between the bending strength and the elasticity. The bimodal porous silica had higher strength and elastic modulus compared with other porous materials at the same porosity probably due to the presence of homogeneous micrometer-scale macropores.     

Effect of pore size/distribution in TiO2 films on agarose gel electrolyte-based dye-sensitized solar cells

This study develops a simple method to change the distribution of the pore size in a TiO₂ layer, using polyethylene glycol (PEG), while maintaining nearly the same surface area and porosity to clarify how large pores affect the performance of dye-sensitized solar cells (DSSCs). Specifically, a heating step at 100 °C for a specific duration is added prior to PEG removal and TiO₂ sintering at 400 °C. This process transforms the role of the PEG from a surfactant to a pore generator (porogen) and forms larger pores, depending on the loading and aggregation time for the PEG to gain larger pores. The effect of larger pores in TiO₂ films under 30 % PEG loading, on the performance of an agarose gel electrolyte-based DSSC, was further investigated using the ionic liquid, 1-allyl-3-ethylimidazolium iodide (AEII). The I–V characteristic and the electrochemical impedance spectroscopy analysis show that larger pores readily improve redox couple diffusion in a TiO₂ porous electrode and modify the interface between electrolyte and TiO₂. Using the optimized TiO₂ film with larger pores (30 % PEG loading, 100 °C/60 min), an efficiency of 7.43 % is achieved for the agarose gel electrolyte-based DSSC, which represents a 26.1 % improvement over TiO₂ without the addition of PEG.     

Influence of the seed polymer on the chromatographic properties of size monodisperse polymeric separation media prepared by a multi-step swelling and polymerization method

Monodisperse polymer particle-based separation media were prepared by a multi-step swelling and polymerization method with two pairs of monomers and two porogenic solvents. Their chromatographic properties were compared to those of beads prepared by a corresponding suspension polymerization method without the use of seed polymer to ascertain the influence of the seed polymer on their porous structures. A large change in porous structure was observed when the swollen particle consisting of monomers and porogenic solvents contained at least one good solvent for the polystyrene seed polymer, allowing it to remain in the polymerizing medium. In contrast, when the polystyrene seed particle was excluded from the swollen oil droplets, due to its poor solubility in the monomers and the porogenic solvents, there was no difference in the chromatographic properties such as pore volume, pore size, pore size distribution, or retention selectivity between the multi-step swelling and polymerization method and the suspension polymerization method. Since the only difference between the multi-step swelling and polymerization method and the suspension method is the use of the seed polymer, it appears that a very small amount (< 1% v/v) of seed polymers in the enlarged swollen droplets plays an important role as a porogen and affects the porous structure as well as the chromatographic properties of the monodisperse polymer particle-based separation media. © 1993 John Wiley & Sons, Inc.     

Fabrication of Porous Polyimide Membrane with Through-Hole via Multiple Solvent Displacement Method

Porous polyimide (PI) membranes are widely used in separation processes because of their excellent thermal and mechanical properties. However, the applications of porous PI membranes are limited in the nanofiltration range. In this study, porous PI membranes with through-holes have been successfully fabricated by the novel multiple solvent displacement method. This new method requires only a porous polyamic acid (PAA) membrane, which was prepared by immersing PAA film in N-methylpyrrolidoneebk; (NMP) prior to immersing it in a mixed solvent consisting of NMP and a poor solvent, followed by immersion only in poor solvent. The pore size, morphology, porosity, and air permeability demonstrated that the fabricated PI membranes had a uniformly porous structure with through-holes over their surface. This new method enabled control of pore size (3–11 μm) by selecting a suitable poor solvent. This multiple solvent displacement method is highly versatile and promising for the fabrication of porous PI membranes.     

Quantification of Porous Properties of Shear Crystallized Lipids

The aim of this study was to investigate the impact that shear and composition have on the structural properties associated with the porous phases of lipids. To accomplish this aim, we developed eight main crystallized samples using cocoa butter (CB) or trilaurin (TL) in the presence or absence of monostearate (M) (5% w/w). The samples were sheared at 500 s⁻¹ using random (RS) or laminar (LS) shear at a cooling rate of 2 °C/min. Using the maximal ball (MB) algorithm, several empirical void measurements such as connectivity (z), pore and throat volume weighted radii (R₄₃), and void fraction (v) were quantified using 3D X-ray microcomputed tomography images. Most void features were identified as micropores (R ≥ 10 μm) possibly originating from the crystallization process and post-process crystal growth. Likewise, depending on the applied treatments, mechanisms impacting void formation were found to produce noticeable variation in v (0.019 to 0.139) and to determine whether void morphology was spherical, irregular, and/or highly connected.     

Synthesis,morphology, and nonisothermal crystallization behavior of poly(trimethylene terephthalate)/poly(propylene glycol) segmented random copolymers

Poly(trimethylene terephthalate)/poly(propylene glycol) (PTT/PPG) segmented random copolymers were synthesized by melt copolycondensation. The weight fraction of PPG blocks was ranged from 12.1 to 33.4 wt%, which was confirmed by ¹H NMR spectroscopy. The result of wide‐angle X‐ray diffractometer indicated that all copolymers had the same crystal structure of PTT homopolymer at room temperature. At a determined crystallization temperature, ring‐banded spherulites could be observed in all copolymers samples, and the band spacing increased with the increase of PPG content. Morphologies of copolymers after nonisothermal crystallization process were strongly depended on the cooling rate. Well‐defined ring‐banded spherulites can be observed only at moderate cooling (20°C/min), while it was really hard to be observed at too low (2.5°C/min) or too high (by air‐quenching) cooling rate. Moreover, the size of spherulites decreased with the increase of cooling rate. Finally, different nonisothermal crystallization kinetics were adopt to analyze this copolymer system, and only the Mo method was suitable to describe this copolymer system. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of porous nanocomposite scaffolds with honeycomb monolith structure by one phase solution freezedrying method

Biodegradable porous nanocomposite scaffolds of poly（lactide-co-glycolide）（PLGA） and L-lactic acid（LAc） oligomer surface-grafted hydroxyapatite nanoparticles（op-HA） with a honeycomb monolith structure were fabricated with the single-phase solution freeze-drying method.The effects of different freezing temperatures on the properties of the scaffolds,such as microstructures,compressive strength,cell penetration and cell proliferation were studied.The highly porous and well interconnected scaffolds with a tunable pore structure were obtained.The effect of different freezing temperature（4℃,-20℃,-80℃and -196℃） was investigated in relation to the scaffold morphology,the porosity varied from 91.2%to 83.0%and the average pore diameter varied from（167.2±62.6）μm to（11.9±4.2）μm while theσ₁₀ increased significantly.The cell proliferation were decreased and associated with the above-mentioned properties.Uniform distribution of op-HA particles and homogeneous roughness of pore wall surfaces were found in the 4℃frozen scaffold.The 4℃frozen scaffold exhibited better cell penetration and increased cell proliferation because of its larger pore size,higher porosity and interconnection.The microstructures described here provide a new approach for the design and fabrication of op-HA/PLGA based scaffold materials with potentially broad applicability for replacement of bone defects.     

Synthesis and Characterizations of Hydroxy-aluminum Cross-Linked Montmorillonite

Cross-linked montmorillonite was prepared by reacting homoionic sodium form of bentonite (Na-M) from Istenmezeje (Hungary) with high molecular weight polyhydroxy-aluminum complex. The complex was prepared by controlled hydrolysis of alumina macrocation. The intercalated clay (Na-Al-M) was thermally treated to convert the hydroxy cations to oxide pillars. The pillared products were characterized by X-ray powder diffraction (XRD), Fourie transform infrared spectroscopy (FTIR), (thermogravimetry (TG), differential thermal analysis (DTA) and thermal analysis-mass spectrometry (TA-MS) methods. The specific surface area as well as pore size and pore structure distribution of samples were measured by nitrogen, water and carbon tetrachloride adsorption, and the heat of immersion was also determined. The pillared products were characterized by d(001) reflections of 19 Å, which is stable even at 500°C. The interaction of polymer alumina caused several changes in the obtained FTIR spectra due to the formation of different new bonds. The rate of dehydroxylation of the pillared product is very moderate, the water release occurred in different temperature ranges according to TA-MS results. Dehydration starts at interfaces and at the wall of pores, occurring nearly with uniform rate at 250-500°C. DTA curve indicates the formation of a new phase at 950°C. The obtained surface area of the pillared product by nitrogen adsorption becomes larger (208 m2 g-1) with respect to the non pillared clay, which decreases less than 10% upto 700°C. The pillared sample has a definite pore structure, the quantity of micropores (0-40 Å) decreased with increasing of macropores (>1000 Å). The obtained domestic pillared montmorillonite possesses a high degree of thermal stability and may be used as adsorbent.