Comparison of Voltammetric Techniques for Ammonia Sensing in Ionic Liquids

In electroanalytical chemistry, it is often observed that square wave voltammetry (SWV) and differential pulse voltammetry (DPV) are more sensitive techniques compared to linear sweep voltammetry (LSV), due to their method of sampling which minimises the charging current (non‐faradaic processes). In this work, a comparison of the three techniques (LSV, DPV and SWV) is performed for ammonia (NH₃) gas oxidation (a chemically and electrochemically irreversible redox process) in an ionic liquid over a concentration range of 10–100 ppm. Four different platinum electrodes are employed: a screen‐printed electrode (SPE), a thin‐film electrode (TFE), a microarray thin‐film electrode (MATFE) and a Pt microdisk electrode (μ‐disk). Calibration plots (current vs concentration) for all three different electrochemical techniques on all four surfaces showed excellent linearity with increased concentrations of NH₃ gas and relatively low limits of detection (LODs). On the larger mm‐sized surfaces (SPE and TFE), the current responses for LSV and SWV were quite similar, but DPV gave the lowest currents. Whereas for the smaller micron sized electrodes (MATFE and μ‐disk), currents were of the order LSV>SWV>DPV, with LSV being far superior to the pulse techniques. These findings suggest that the pulse techniques of SWV and DPV may not be the optimum methods, particularly on microelectrodes, for the detection of analytes such as ammonia in RTILs.     

Synthesis of Ferrocene Based Naphthoquinones and its Application as Novel Non‐enzymatic Hydrogen Peroxide

At present, a highly sensitive hydrogen peroxide (H₂O₂) sensor is fabricated by ferrocene based naphthaquinone derivatives as 2,3‐Diferrocenyl‐1,4‐naphthoquinone and 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone. These ferrocene based naphthaquinone derivatives are characterized by H‐NMR and C‐NMR. The electrochemical properties of these ferrocene based naphthaquinone are investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) on modified glassy carbon electrode (GCE). The modified electrode with ferrocene based naphthaquinone derivatives exhibits an improved voltammetric response to the H₂O₂ redox reaction. 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone show excellent non‐enzymatic sensing ability towards H₂O₂ response with a detection limitation of 2.7 μmol/L a wide detection range from 10 μM to 400 μM in H₂O₂ detection. The sensor also exhibits short response time (1 s) and good sensitivity of 71.4 μA mM^?1 cm^?2 and stability. Furthermore, the DPV method exhibited very high sensitivity (18999 μA mM^?1 cm^?2) and low detection limit (0.66 μM) compared to the CA method. Ferrocene based naphthaquinone derivative based sensors have a lower cost and high stability. Thus, this novel non‐enzyme sensor has potential application in H₂O₂ detection.     

Voltammetric Determination of Metronidazole Using a Sensor Based on Electropolymerization of α‐Cyclodextrin over a Carbon Paste Electrode

An electrochemical sensor for metronidazole (MTZ) was built via the surface modification of a carbon paste electrode (CPE) by a film obtained through electropolymerization of α‐cyclodextrin (CPE_α‐CD). The CPE_α‐CD was characterized by cyclic voltammetry (CV) and atomic force microscopy (AFM), by both techniques was demonstrated that the polymer film is coating the electrode surface. The electroreduction behaviour of MTZ in HClO₄ media as a supporting electrolyte was studied by differential‐pulse voltammetric (DPV) technique. The DPV electrochemical process was observed to be diffusion controlled and irreversible. Under optimal conditions, the peak current was proportional to MTZ concentration in the range of 0.5 to 103.0 μM with a detection limit of 0.28±0.02 μM. The method was successfully applied to quantify of MTZ in pharmaceutical formulations. In addition, this proposed MTZ sensor exhibited good reproducibility, long‐term stability and fast current response.     

Electrochemical investigation and determination of ceftazidime in pharmaceutical dosage forms and human urine

A voltammetric study of the oxidation of Ceftazidime (CEFT) has been carried out at the glassy carbon electrode by cyclic, differential pulse (DPV) and square wave (SWV) voltammetry. The oxidation of CEFT was irreversible and exhibited diffusion controlled process depending on pH. The oxidation mechanism was proposed and discussed. According to the linear relationship between the peak current and concentration, DPV and SWV voltammetric methods for CEFT assay in pharmaceutical dosage forms and human urine were developed. For analytical purposes, a well resolved diffusion controlled voltammetric peak was obtained in 0.1 M H₂SO₄ at 1.00 and 1.02 V for differential pulse and square wave voltammetric techniques, respectively. The linear response was obtained within the range of 4 × 10^?6?8 × 10^?5 M with a detection limit of 6 × 10^?7 M for differential pulse and 4 × 10^?6–2 × 10^?4 M with a detection limit of 1 × 10^?6 M for square wave voltammetric technique. The determination of CEFT in 0.1 M H₂SO₄ was possible over the 2 × 10^?6–1 × 10^?4 M range in urine sample for both techniques. The standard addition method was used for the recovery studies.     

A Sensitive Electrochemical Sensor for Voltammetric Determination of Ganciclovir Based on Au‐ZnS Nanocomposite

An electrode modified with ZnS and gold nanoparticles (Au‐ZnS NPs) is introduced for highly sensitive voltammetric determination of ganciclovir (GCV). Surface structure and topography of the modified electrode was studied by SEM, EDX and XRD techniques. Electrochemical oxidation of GCV was investigated by cyclic (CV) and square wave voltammetry (SWV) in Briton‐Robinson buffer solution (pH 1.5). The results showed that electrochemical oxidation of GCV at the Au‐ZnS modified glassy carbon electrode (GCE) is irreversible and exhibited diffusion controlled electrode process over the pH range from 1.0 to 6.0. The oxidation potential peak and pH relationship showed that electrons and protons were transferred simultaneously over the electrochemical oxidation process. Using the proposed sensor, the linear calibration curves were obtained in the ranges of 0.04–1.50 μM and 1.5–70.0 μM with detection limit of 0.01 μM GCV by SWV technique. The modified electrode was successfully applied as a sensitive, reproducible and repeatable sensor for determination of the trace amount of GCV in human serum, urine and cymevene vials. Reasonable results were obtained from comparing the measurements of the real samples by the new sensor to high performance liquid chromatography (HPLC) as a standard method.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.     

Anodic Voltammetric Behavior and Determination of Antihistaminic Agent: Fexofenadine HCl

Abstract

A voltammetric study of the oxidation of fexofenadine HCl (FEXO) has been carried out at the glassy carbon electrode. The electrochemical oxidation of FEXO was investigated by cyclic, linear sweep, differential pulse (DPV), and square wave (SWV) voltammetry using glassy carbon electrode. The oxidation of FEXO was irreversible and exhibited diffusion‐controlled process depending on pH. The dependence of intensities of currents and potentials on pH, concentration, scan rate, nature of the buffer was investigated. Different parameters were tested to optimize the conditions for the determination of FEXO. For analytical purposes, a very well resolved diffusion‐controlled voltammetric peak was obtained in Britton‐Robinson buffer at pH 7.0 with 20% constant amount of methanol for DPV and SWV techniques. The linear response was obtained in supporting electrolyte in the ranges of 1.0×10^?6–2.0×10^?4 M with a detection limit of 6.6×10^?9 M and 5.76×10^?8 M and in serum samples in the ranges of 2.0×10^?6–1.0×10^?4 M with a detection limit of 8.08×10^?8 M and 4.97×10^?8 M for differential pulse and square wave voltammetric techniques, respectively. Only square wave voltammetric technique can be applied to the urine samples, and the linearity was obtained in the ranges of 2.0×10^?6–1.0×10^?4 M with a detection limit of 2.00×10^?7 M. Based on this study, simple, rapid, selective and sensitive two voltammetric methods were developed for the determination of FEXO in dosage forms and biological fluids. For the precision and accuracy of the developed methods, recovery studies were used. The standard addition method was used for the recovery studies. No electroactive interferences were found in biological fluids from the endogenous substances and additives present in tablets.     

Determination of Azidothymidine – an Antiproliferative and Virostatic Drug by Square‐Wave Voltammetry

The 3′‐azido‐3′‐deoxythymidine (AZT, Zidovudine) is an antiproliferative and virostatic drug widely used in human immunodeficiency virus type 1 (HIV‐1) infection treatment. With respect to side effects of high doses and a short half‐life of AZT, a fast and simple detection method for this agent could be helpful. The aim of our study was to determine AZT levels in natural samples (urine, serum, whole blood, and cell cultures, such as the HaCaT line of keratinocytes) without their mineralization and/or purification, by means of electrochemical methods using hanging mercury drop electrode (HMDE). On this electrode, AZT undergoes irreversible reduction at the peak potential near E_p?1.1 V (vs. Ag/AgCl/3 M KCl). Reduction AZT signals were measured by cyclic voltammetry (CV), differential pulse voltammetry (DPV), square‐wave voltammetry (SWV), and constant current chronopotentiometric stripping analysis (CPSA). In phosphate buffer (pH 8) the SWV yielded the best AZT signal with the detection limit of 1 nM. The determination of AZT concentration in biological materials is affected by electroactive components, such as proteins and DNA. For monitoring the influence of these compounds, AZT reduction was performed in the presence of 10 μg/mL calf thymus ssDNA and/or 100 μg/mL bovine serum albumin. In these cases, the detection limit increased to 0.25 μM. Also studied was the AZT concentration in keratinocyte cells (HaCaT line) during cell cultivation. It has been shown that the SWV may be considered as a useful tool for the determination of AZT concentration in cell cultures, and for monitoring AZT pharmacokinetics.     

Voltammetric Determination of Uric Acid at a Fullerene‐C60‐Modified Glassy Carbon Electrode

Glassy carbon electrode modified by microcrystals of fullerene‐C₆₀ mediates the voltammetric determination of uric acid (UA) in the presence of ascorbic acid (AA). Interference of AA was overcome owing to the ability of pretreated fullerene‐C₆₀‐modified glassy carbon electrode. Based on its strong catalytic function towards the oxidation of UA and AA, the overlapping voltammetric response of uric acid and ascorbic acid is resolved into two well‐defined voltammetric peaks with lowered oxidation potential and enhanced oxidation currents under conditions of both linear sweep voltammetry (LSV) and Osteryoung square‐wave voltammetry (OSWV). At pH 7.2, a linear calibration graph is obtained for UA in linear sweep voltammetry over the range from 0.5 μM to 700 μM with a correlation coefficient of 0.9904 and a sensitivity of 0.0215 μA μM^?1 . The detection limit (3σ) is 0.2 μM for standard solution. AA in less than four fold excess does not interfere. The sensitivity and detection limit in OSWV were found as 0.0255 μA μM^?1 and 0.12 μM, for standard solution respectively. The presence of physiologically common interferents (i.e. adenine, hypoxanthine and xanthine) negligibly affects the response of UA. The fullerene‐C₆₀‐modified electrode exhibited a stable, selective and sensitive response to uric acid in the presence of interferents.     

Voltammetric Analysis of Oxymetazoline Hydrochloride at Zeolite – Modified Carbon Paste Electrode in Micellar Medium

Simple, sensitive, accurate and inexpensive differential pulse (DPV) and square wave (SWV) voltammetric methods utilizing zeolite modified carbon paste electrode (ZMCPE) were developed for the determination of Oxymetazoline hydrochloride (OXM) in nasal drops. Various experimental parameters were optimized using cyclic voltammetry (CV). Calibration curves were linear over the concentration ranges 9.8×10⁻⁸–3.6×10⁻⁶ M and 9.8×10⁻⁶–9×10⁻⁵ M for DPV and SWV, respectively. The DPV method showed a limit of detection (LOD) of 1.04×10⁻⁷ M. The method was applied for the determination of OXM in pharmaceutical formulation with an average recovery of 101.18 % (%RSD=0.41, n=9).     

Sensitive Electrochemical Detection of Horseradish Peroxidase at Disposable Screen‐Printed Carbon Electrode

A rapid, simple and sensitive electrochemical assay of horseradish peroxidase (HRP) performed on disposable screen‐printed carbon electrode was developed. HRP activities were monitored by square‐wave voltammetric (SWV) measuring the electroactive enzymatic product in the presence of o‐aminophenol and hydrogen peroxide substrate solution. SWV analysis demonstrated a greater sensitivity and shorter analysis time than the widely used amperometric and differential‐pulsed voltammetric methods. The voltammetric characteristics of substrate and enzymatic product as well as the parameters of SWV analysis were optimized. Under optimized conditions, a linear response for HRP from 0.003 to 0.1 U/mL and a detection limit of 0.002 U/mL (1.25×10^?15 mol in 25 μL) were obtained with a good precision (RSD=8%; n=6). This rapid and sensitive HRP assay with microliter‐assay volume could be readily integrated to portable devices and point‐of‐care (POC) diagnosis applications.     

Anodic voltammetric behavior of ascorbic acid and its selective determination in pharmaceutical dosage forms and some Rosa species of Turkey

Ascorbic acid is the most common electroactive biological compound found in some plant species (e.g., Citrus species, Rosa species). The electrochemical oxidation of ascorbic acid was investigated by cyclic, linear sweep, differential pulse (DPV), and square wave (SWV) voltammetry. For analytical purposes, a very well-resolved diffusion-controlled voltammetric peak was obtained in acetate buffer at pH 3.50 for DPV and SWV. The linear response was obtained in the range of 3.52–176.1 μg/mL with a detection limit of 0.88 μg/mL for DPV and 0.52 μg/mL for SWV. Based on this study, simple, rapid, selective, and sensitive voltammetric methods were developed for the determination of ascorbic acid in pharmaceutical dosage forms and Rosa species (R. dumalis ssp. boissieri var. boissieri, R. canina, R. pulverulenta, R. heckeliana ssp. vanheurckiana, and R. montana subsp. woronowii). The results obtained are compared with the HPLC data. The developed methods enable the extracts to be analyzed without the necessity of any time-consuming separation. The text was submitted by the authors in English.     

Selective Voltammetric Detection of Uric Acid in the Presence of Ascorbic Acid at Well‐Aligned Carbon Nanotube Electrode

The voltammetric behaviors of uric acid (UA) and L ‐ascorbic acid (L ‐AA) were studied at well‐aligned carbon nanotube electrode. Compared to glassy carbon, carbon nanotube electrode catalyzes oxidation of UA and L ‐AA, reducing the overpotentials by about 0.028 V and 0.416 V, respectively. Based on its differential catalytic function toward the oxidation of UA and L ‐AA, the carbon nanotube electrode resolved the overlapping voltammetric response of UA and L ‐AA into two well‐defined voltammetric peaks in applying both cyclic voltammetry (CV) and differential pulse voltammetry (DPV), which can be used for a selective determination of UA in the presence of L ‐AA. The peak current obtained from DPV was linearly dependent on the UA concentration in the range of 0.2 μM to 80 μM with a correlation coefficient of 0.997. The detection limit (3δ) for UA was found to be 0.1 μM. Finally, the carbon nanotube electrode was successfully demonstrated as a electrochemical sensor to the determination of UA in human urine samples by simple dilution without further pretreatment.     

Rapid Electrochemical Detection of Vanillin in Natural Vanilla

A commercially available and disposable multiwalled carbon nanotube screen‐printed electrode (CNT‐SPE) was employed to detect and determine vanillin compounds in natural vanilla. The voltammetric behaviour of vanillin at the CNT‐SPE is examined and shown to be a sensitive method for quantifying vanillin. Linear calibration for vanillin in the range of 2.5–750 μM was obtained with a detection limit of 1.03 μM and a quantification limit of 3.44 μM. The developed method comprises a simple sample preparation method and a sensitive electrochemical detection for the quantification of vanillin in vanilla pods and is an easy and simple procedure for manufacturers and consumers.     

Electrochemical characterisation of nefazodone hydrochloride and voltammetric determination of the drug in pharmaceuticals and human serum

Nefazodone, an antidepressant was electrochemically studied in various buffer systems and at different pH using glassy carbon electrode. Nefazodone was electrochemically oxidized at all pH values. According to the linear relation between the peak current and the nefazodone concentration differential pulse (DPV) and square wave (SWV) voltammetric methods for its quantitative determination in pharmaceuticals and human serum were developed. For analytical purposes, a very well resolved diffusion controlled voltammetric peak was obtained in 0.1 M H₂SO₄ at 0.99 and 1.03 V for DPV and SWV techniques, respectively. The linear response was obtained in the ranges of 8×10⁻⁷ to 6×10⁻⁴ M with a detection limit of 2.1×10⁻⁷ M for DPV and 1.17×10⁻⁷ M for SWV techniques. The repeatability and reproducibility of the methods were within 1.03, 0.81% relative standard deviations (R.S.D.) for peak currents and 0.40, 0.20% R.S.D. for peak potentials, for DPV and SWV, respectively. Precision and accuracy of the developed method was checked by recovery studies. The proposed methods were successfully applied to the individual tablet dosage form and human serum.     

Application of nanosized MCM-41 to fabrication of a nanostructured electrochemical sensor for the simultaneous determination of levodopa and carbidopa

A novel carbon paste electrode modified with nanosized mesoporous MCM-41 was prepared, and used as an electrochemical sensor to study the electro oxidation of levodopa (LD), carbidopa (CD) and their mixtures. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of LD and CD has been explored at the modified electrode. The electrochemical sensor displayed a good resolving function for the overlapping voltammetric responses of LD and CD into two separate peaks with a potential difference of 370 mV. DPV peak currents of LD increased linearly with concentration over the 0.13 μM to 1250.00 μM range and exhibited a detection limit of 0.072 μM. Also, the proposed electrochemical sensor was used for the determination of LD and CD in some real samples, using the standard addition method.     

Highly Sensitive Amperometric Sensor for Eugenol Quantification Based on CeO2 Nanoparticles and Surfactants

Amperometric sensor for eugenol based on glassy carbon electrode (GCE) modified with CeO₂ nanoparticles dispersed in surfactant was fabricated. The effect of surfactant nature (sodium dodecylsulfate, cetylpyridinium bromide (CPB) and Brij® 35) on eugenol voltammetric behaviour was tested. In comparison to CeO₂‐H₂O/GCE, CeO₂‐CPB/GCE showed 2.8‐fold increased current and 70 mV cathodic shift of potential in the diffusion‐controlled irreversible electrooxidation. The electrodes were characterized with SEM and EIS. CeO₂‐CPB/GCE showed significantly lower charge transfer resistance (2.6±0.3 kΩ vs. 20±1 kΩ for CeO₂‐H₂O/GCE and 173±9 kΩ for GCE). Under conditions of DPV, the sensor linear dynamic range is 0.075‐75.0 μM of eugenol with the limits of detection (LOD) and quantification (LOQ) of 19.1 and 63.8 nM, respectively. The sensor exhibited high sensitivity, selectivity, good reproducibility and fast response and was applied for the real samples analysis (essential oils and clove spices). The results obtained correspond well to the data of spectrophotometric method.     

Determination of Anti-Parkinson Drug Pramipexole Using a Label-free Biosensor and Evaluation of its Interaction with ds-DNA

In this study, we fabricated an effective and sensitive DNA biosensor based on flower-like Pt/NiCo₂O₄ modified carbon paste electrode (FL-Pt/NiCo₂O₄/CPE) for detection of pramipexole (PPX). Spectrophotometry, differential pulse voltammetry (DPV) and docking methods were employed to evaluate the interaction of DNA-PPX. Moreover, the DPV technique was chosen to monitor the electrochemical response of guanine on the DNA biosensor. The relationship between the concentration of PPX and the oxidation signal of guanine was linear in the range of 0.4 to 310.0 μM and a limit of detection (LOD) of 0.09 μM was calculated.     

Electrochemical Determination of Norepinephrine on Cathodically Pretreated Poly(1,5‐diaminonaphthalene) Modified Electrode

A sensitive and simple electrochemical method for norepinephrine (NE) determination was developed based on a poly(1,5‐diaminonaphthalene) film electrode (PDAN). Cathodically pretreated PDAN presents good selectivity, sensitivity, and reproducibility for NE. The polymer film can be easily electropolymerized onto a platinum electrode by cyclic voltammetry in 1.0 M HClO₄. A cathodic pretreatment, consisting of the application of a potential of ?0.7 V for 3 s (vs. Ag/AgCl) to PDAN before each voltammetric measurement, enhanced the electrochemical activity of NE with no inference of ascorbic acid (AA). In optimized conditions, PDAN presents linear responses for NE in the range of 9.90 to 90.9 µM by differential pulse voltammetry (DPV) with a detection limit of 1.82 µM. A relative standard deviation of 3.0 % was obtained for 10 consecutive measurements of 40.0 µM NE solutions. The cathodically pretreated PDAN was successfully applied for NE determination in pharmaceutical formulation samples.     

Carbon Nanotubes Modified Graphite Electrodes for Monitoring of Biointeraction Between 6‐Thioguanine and DNA

In this present study, single‐walled carbon nanotubes (SWCNT) modified disposable pencil graphite electrodes (SWCNT‐PGEs) were developed for the electrochemical monitoring of anticancer drug, and its interaction with double stranded DNA (dsDNA). Under this aim, SWCNT‐PGEs were applied for the first time in the literature to analyse of 6‐Thioguanine (6‐TG), and also to investigate its interaction with DNA by voltammetric and impedimetric methods. The surface morphologies of PGE and SWCNT‐PGE were explored using scanning electron microscopy (SEM) and electrochemical characterization of unmodified/modified electrodes was performed by cyclic voltammetry (CV). Experimental parameters; such as, the concentration of 6‐TG and its interaction time with dsDNA were optimized by using differential pulse voltammetry (DPV). Additionally, the interaction of 6‐TG with dsDNA was studied in case of different interaction times by electrochemical impedance spectroscopy (EIS) in contrast to voltammetric results. The detection limit of 6‐TG was found to be 0.25 μM by SWCNT‐PGE.