溶剂热法合成不同形貌的Co3O4及其电容特性

采用溶剂热法以不同的钴盐在水-正丁醇体系中合成了不同形貌及尺寸的纳米Co3O4. 采用XRD和TEM对产物的物相和形貌进行表征. 结果表明, 通过改变反应体系中阴离子的种类, 可以控制产物Co3O4的形貌与晶粒尺寸. 通过循环伏安法、恒流充放电和交流阻抗法对Co3O4电极材料的电化学性能进行表征. 结果表明, Co3O4的形貌与晶粒尺寸对其电化学性能有显著影响. 在2 mol·L-1 KOH溶液中, 在-0.40 - 0.55 V (vs SCE)电位范围内, 由Co(NO3)2制备的球形Co3O4表现出更好的电容特性,单电极初始比容量达362.0 F·g-1, 经过400 次循环后比容量仍保持90%.     

稀土Dy3+掺杂Fe3O4的合成及电磁性质

通过溶胶-凝胶法，合成了稀土Dy^3＋掺杂的Fe3O4样品，研究了掺杂对电磁性质的影响。通过X射线衍射分析发现，由于离子半径的不匹配，Fe3O4中稀土离子的高浓度掺杂不能实现，仅有极少量的稀土离子取代了Fe3O4中的Fe^3＋。通过振动样品磁强计对磁性质进行了表征，掺杂引起样品饱和磁化强度发生变化，这可能是因为Dy^3＋取代引起的磁化强度增加和杂相引起的磁化强度降低共同作用的结果。四电极法研究隧道磁阻发现，磁阻与掺杂量的关系表现出降低-升高-降低的特殊变化规律。这主要是由于掺杂Fe3O4自旋极化率降低导致隧穿磁阻下降，同时，掺杂Fe3O4在隧穿颗粒体系中实现了第二相即绝缘相的同步合成，第二相的出现有利于隧穿磁阻的增加。     

Co3O4 纳米棒的溶剂热合成及形成机理分析

Co3O4 nanorods have been synthesized at 160℃ for 10 h in the solution of oleic and n-cetane by an emulsion-solvothermal method using Co（NO3）2·6H2O as starting materials. The as-prepared product was characterized by X-ray powder diffraction（XRD）,transmission electron microscope（TEM）,and vibrating sample magnetometer（VSM）. The formation mechanism of the prepared product was analyzed based on formation of rod-like micelles of oleic acid. Cobalt ions can migrate into the micelle core for the nucleation and growth of Co3O4 . The results show that the as-prepared Co3O4 nanorods are with the average size 25×100 nm and in the cubic phase. The magnetic susceptibility meets about linearly with the applied magnetic field at room temperature,and the coercivity （Hc）and remanent magnetization（Ms）values of the product at room temperature are 353 Oe and 0.4 emu/g,respectively. This simple route is also expanded to synthesize other materials with the rod-like morphology.     

纳米Fe3O4/聚苯乙烯均匀分散体系的制备及结构

用化学共沉淀法制备了Fe3O4纳米颗粒,以油酸为表面活性剂,苯乙烯为载液,制备了稳定的纳米Fe3O4可聚合磁流体,将可聚合磁流体经自由基引发聚合制成纳米Fe3O4/聚苯乙烯均匀分散体系,用WAXRD研究了Fe3O4纳米粒子的结晶情况;用FTIR研究了油酸表面改性前后Fe3O4粒子表面官能团的变化;用TEM研究了Fe3O4颗粒的粒径大小及其在苯乙烯单体和聚苯乙烯中的分散情况;用DSC和TGA研究了纳米Fe3O4/聚苯乙烯均匀分散体系的玻璃化转变温度(Tg)和热稳定性,结果表明,合成的纳米Fe3O4为立方晶型,平均粒径在10nm左右,油酸分子在Fe3O4表面是化学吸附,经表面处理的Fe3O4超细颗粒在苯乙烯和聚苯乙烯基体中分散较均匀.界面粘结较好,含1.8％Fe3O4纳米颗粒的聚苯乙烯的最大热失重温度比聚苯乙烯提高了13K,Fe3O4/聚苯乙烯复合体系的饱和磁化强度σs为17.43emu/g.     

Microwave‐assisted Synthesis and Its Reversible Li‐storage Properties of Porous Sheet‐like Co3O4

Porous Co₃O₄ nanosheets were designed and fabricated from common Co(NO₃ )₂ solution without any surfactants or templates under microwave radiation conditions. After the microstructures and morphologies were characterized by scanning electron microscope (SEM ), X‐ray powder diffraction (XRD ), transmission electron microscopy (TEM ), and N₂ absorption/desorption isotherms techniques, the obtained Co₃O₄ nanosheets were applied for reversible Li‐storage, displaying larger capacity, better cycling performance and rate capability, i.e., a reversible specific capacity of ca. 800 mAh /g during initial 30 cycles and a reversible capacity of 450 mAh /g at 2C for Co₃O₄ nanosheets, which were almost twice higher than those for Co₃O₄ nanoparticles. The improved cycling stability could be attributed to the remarkable synergistic effects between porous structures and nanosheet‐like morphologies.     

链霉亲和素-异硫氰酸荧光素偶联核壳型Fe3O4/Au纳米晶的合成及性质

采用改进的Polyol合成法,以PEO-PPO-PEO为表面活性剂制备了链霉亲和素-异硫氰酸荧光素偶联的Fe3O4/Au纳米粒子;利用透射电镜和X射线衍射仪分析证实了Fe3O4/Au的核壳型纳米结构,确定了其粒径和分布;采用紫外-可见吸收光谱仪和荧光光谱仪测定了所制备的纳米粒子的光学活性和荧光特性,并采用振动样品磁强计(VSM)测量了其磁化率.结果表明,所制备的Fe3O4/Au纳米粒子具有光学活性和荧光特性,以及优异的磁性.     

单分散Fe3O4纳米颗粒的控制合成和表征

以十八烯为溶剂、乙酰丙酮铁为铁源,并在油酸、油胺的辅助作用下,通过热分解法成功合成了单分散Fe3O4纳米颗粒。讨论了实验参数如反应温度、表面活性剂的量和种类、溶剂、油酸、油胺对单分散Fe3O4纳米颗粒的尺寸及形貌的影响。利用X射线衍射（XRD）、透射电子显微镜（TEM）、选区电子衍射（SAED）和高分辨透射电子显微镜（HRTEM）对所得产物的物相、结构、尺寸和形貌进行了表征分析。通过振动样品磁强计（VSM）表征产物磁性能,表明在室温下,Fe3O4纳米颗粒的饱和磁化强度（Ms）和矫顽力（Hc）分别为74.0 emu/g,72.6 Oe。     

Fe(NO3)3·9H2O as Efficient Catalyst for One‐pot Synthesis of Highly Functionalized Piperidines

Fe(NO₃)₃·9H₂O is used as an efficient and effective catalyst for the one‐pot three‐component synthesis of highly functionalized piperidines from aromatic aldehydes, anilines and b–ketoesters in ethanol at ambient temperature. This procedure includes some important aspects like the easy work‐up, no need to column chromatography, simple and readily available precursors, and good to high yields.     

Green and Highly Efficient Synthesis of Mono‐ and Bis‐Benzothiazoles in the Presence of Fe(SD)3 under Ultrasound Irradiation

A convenient, practical, green, and environmentally friendly method was developed for the synthesis of benzothiazoles from 2‐aminothiophenol and various aldehydes. Bis‐benzothiazoles were synthesized in high yield under mild reaction conditions. Products were obtained in the presence of in situ prepared Fe(SD )₃ [iron(III ) dodecyl sulfate] as a combined Lewis acid–surfactant catalyst (LASC ) in water under ultrasound irradiation.     

One‐Pot Template‐Free Synthesis of NaYF4 Upconversion Hollow Nanospheres for Bioimaging and Drug Delivery

Hollow‐structured nanomaterials with fluorescent properties are extremely attractive for image‐guided cancer therapy. In this paper, sub‐100 nm and hydrophilic NaYF₄ upconversion (UC) hollow nanospheres (HNSs) with multicolor UC luminescence and drug‐delivery properties were successfully prepared by a facile one‐pot template‐free hydrothermal route using polyetherimide (PEI) polymer as the stabilizing agent. XRD, SEM, TEM, and N₂‐adsorption/desorption were used to characterize the as‐obtained products. The growth mechanism of the HNSs has been systematically investigated on the basis of the Ostwald ripening. Under 980 nm excitation, UC emissions of HNSs can be tuned by a simple change of the concentration or combination of various upconverters. As a result, the PEI‐coated HNSs could be used as efficient probes for in vitro upconversion luminescence (UCL) cell imaging. Furthermore, a doxorubicin storage/release behavior and cancer‐cell‐killing ability investigation reveal that the product has the potential to be a drug carrier for cancer therapy.     

尺寸可控的单分散四氧化三铁微球的省时制备

Monodisperse Fe₃O₄ microspheres with tunable diameters and high magnetic saturation were synthesized by a solvothermal reduction method. It was found that the morphology and structure of the Fe₃O₄ microspheres could be tuned by simply altering the amount of the reactants such as ferric chloride, sodium acetate, water, and the reaction time. The Fe₃O₄ microspheres obtained via this method possessed high purity, crystallinity, and a nearly spherical shape. Furthermore, they were monodispersed and no aggregation was found. Such monodisperse Fe₃O₄ microspheres had tunable diameters of 400-700 nm and the fabrication time was only 2-4 h. The products showed high magnetic saturation values, and their yields were typically more than 94%.     

Electrochemical Monitoring of Methotrexate Anticancer Drug in Human Blood Serum by Using in situ Solvothermal Synthesized Fe3O4/ITO Electrode

Here, we reported on a one‐step fabrication of magnetite Fe₃O₄ nanoparticles/indium tin oxide (ITO) electrode based on the direct growing of Fe₃O₄ nanoparticles on the ITO surface by using a solvothermal process. The modified electrode was used as electrochemical methotrexate (MTX) biosensor with high sensitivity based on cyclic voltammetry and square wave voltammetry techniques. The results demonstrated a linear relationship between the MTX concentration and its oxidation current peak over a wide range from 10^?5 to 10^?14 mole/L with a limit of detection of 0.4×10^?15 M based on the square wave voltammetry (SWV) technique. In addition, Fe₃O₄/ITO electrode showed a good capability for measuring very low concentrations of MTX drug dissolved in human serum solution. Also, Fe₃O₄/ITO electrode was used for detecting MTX in blood serum samples collected from patients after their treatment with MTX. The prepared electrode showed the higher sensitivity that higher than the Viva‐E instrument, which opens the door for developing a cheap, simple and higher sensitive MTX sensor.     

Shape-controlled Synthesis of Fe3O4 Nanocrystals with Incontinuous Multicavities

In the solvothermal synthesis process, the effect of NaOH dosages of from 0.3 g to 4.0 g on the morphology evolution(from nanoparticles to octahedra) of Fe₃O₄ crystals was carefully investigated. Meanwhile, the growth process of Fe₃O₄ crystals at different reaction time was also investigated. Furthermore, it has been found that the particle size and crystallinity of Fe₃O₄ crystals can be controlled by the dosages of NaOH. In this paper, the increases of both the reaction time and the NaOH concentrations correspond to a minimization process of surface energy for Fe₃O₄ crystals. During the synthesis process, the addition of N₂H₄·H₂O and ethylene glycol in the magnetite not only facilitated the narrow distribution of particle size but also contributed to the formation of incontinuous multicavities with a diameter of about 5 nm.     

Fe_3O_4/SrTiO_3复合光催化剂降解甲基橙

用共沉淀法制备了SrTiO3光催化剂及Fe3O4/SrTiO3复合光催化剂.通过紫外-可见漫反射光谱、XRD、SEM-EDX对其进行表征,以甲基橙为探针分子考察其光催化性能.结果表明,适量Fe3O4的掺入可明显提高Sr-TiO3光催化剂对可见光的吸收,从而增强其光催化性能;在光降解甲基橙的反应中,掺杂10%Fe3O4的SrTiO3光催化剂其催化活性是纯SrTiO3光催化剂的两倍.     

Waste to wealth: conversion of nano‐magnetic eggshell (Fe3O4@Eggshell) to Fe3O4@Ca(HSO4)2: cheap,green and environment‐friendly solid acid catalyst

Eggshell is a hazardous waste by European Union regulations, so that discarded thousands of tons per year. To convert waste (eggshell) to wealth (catalyst), nano‐magnetic eggshell was prepared based on the nano‐Fe₃O₄, and then the eggshell was converted to Ca(HSO₄)₂ with organic acid, namely, chlorosulfonic acid. Based on the back titration, 5.18 mmol SO₄H group was loaded per gram of the nano‐structure. Using this method eggshell was converted to cheap, green and environment‐friendly solid acid catalyst. The prepared catalyst (nano‐ Fe₃O₄@Ca(HSO₄)₂) was characterized by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDX), field emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermal gravimetric analysis (TGA). The activity of eggshell waste‐derived catalysts was successfully evaluated in the synthesis of value‐added products, namely indazolo[1,2‐b]‐phthalazinetrione derivatives as a benchmark multicomponent reaction. In addition, design of experiments shows that increase in amount of catalyst (and temperature), boost the reaction yield, especially with steeper slope at higher temperature.     

超声合成Fe3O4@SiO2复合纳米磁性粒子用于质粒DNA的提纯

用超声合成了Fe3O4@SiO2复合纳米磁性粒子, 并用于质粒DNA的提取. 用透射电镜(TEM)、红外光谱(FT-IR)、震动样品磁场计(VSM)、X光电子能谱仪(XPS)等方法对合成的复合磁性粒子的表面形貌、结构、磁性质等进行了表征, 合成的复合磁微粒粒径分布均匀, 在15～20 nm, 磁响应性好. 用该复合磁微粒提取DNA的纯度能达到A260/A280＝ 1.8±0.1, 琼脂糖电泳证明质粒DNA结构基本没有被破坏, 主要为超螺旋结构, 能满足PCR等后续分子生物学操作的要求.     

Preparation for Magnetic Nanoparticles Fe3O4 and Fe3O4@SiO2 and Heterogeneous Fenton Catalytic Degradation of Methylene Blue

Dyestuff textile wastewater treatment has become a research hotspot due to its high chroma, poor biodegradability, and low toxicity characteristics. In this paper, we have synthesized magnetic Fe₃O₄ and core‐shell Fe₃O₄@SiO₂ materials by hydrothermal methods. These materials were characterized by XRD, TEM, N₂ adsorption‐desorption and so on. These materials’ heterogeneous Fenton has been applied to dye wastewater treatment. Methylene blue was used as a typical target of dye wastewater. Decolorization ratios of methylene blue were determined by different nanostructure composites catalysts. A serious of results of study showed that decolorization ratios of magnetic nanoparticles and core‐shell composites arrived at above 90 % under the weakly acidic or neutral conditions and room temperature. When these catalysts were reused, the results show that Fe₃O₄@SiO₂ materials were possessed with good cycle performance.     

超顺磁Fe_3O_4@PDA核-壳结构纳米粒子的制备及表征

利用多元醇高温热解法和溶液氧化法制备超顺磁四氧化三铁聚多巴胺核-壳结构纳米粒子(Fe_3O_4@PDA)。采用X射线衍射(XRD)、透射电子显微镜(TEM)、动态光散射(DLS)、傅里叶转换红外光谱(FT-IR)和热重分析(TG)等对Fe_3O_4@PDA的结构、形貌和组成进行表征。采用综合物性测试系统(PPMS)对样品的磁性能进行表征。结果表明:Fe_3O_4@PDA的尺寸可以通过氨水与多巴胺的物质的量之比和反应时间进行调控;当Fe_3O_4@PDA中Fe_3O_4的质量分数约为5%时,具有超顺磁性,磁饱和强度为3.8emu/g,比理论值高出36%。     

Fe3O4/聚苯乙烯纳米复合材料的结构与性能

采用油酸(OA)表面改性的粒径均一的Fe3O4纳米粒子(OA-Fe3O4)与工业化聚苯乙烯(PS)通过溶液共混挥发干燥方法得到了具有超顺磁性的OA-Fe3O4/PS纳米复合材料.透射电子显微镜表征结果表明,在OA-Fe3O4质量分数为1%~10%时,OA-Fe3O4纳米粒子均匀分散在PS聚合物基体中.示差扫描量热分析表明,随着纳米粒子加入量的增加,纳米复合材料的玻璃化转变温度逐渐降低.热失重分析表明,OA-Fe3O4的存在显著提高了PS在空气条件下的热稳定性.流变分析表明,随着纳米粒子加入量的增加(0~10%),复合材料黏度逐渐降低.进一步研究了分子量双峰分布的PS与OA-Fe3O4纳米复合体系的流变行为,结果表明,当PS基体的平均分子量大于临界缠结分子量,且填充的纳米粒子的半径小于双峰分布PS的均方旋转半径时,加入纳米粒子仍然导致体系的复合黏度降低.     

相转移方法制备水溶性Fe3O4纳米晶

在有机溶剂中合成了超顺磁性的油溶性Fe₃O₄纳米晶. 利用相转移的方法成功地将油溶性Fe₃O₄纳米晶完全转移至水相中, 其中两性齐聚物——聚马来酸脂肪胺酯作为修饰剂包裹在Fe₃O₄纳米晶的表面. 利用透射电子显微镜(TEM)、红外光谱仪、热失重分析和动态光散射仪对水溶性纳米晶的形貌和结构进行了表征. 所制备的水溶性磁流体在外加磁场的环境中表现出所预期的超顺磁性行为. 两性齐聚物中疏水链的长度能够显著地影响相转移效果, 研究发现利用含有十六个碳链的聚马来酸十六胺酯来转移纳米晶时效果最好. 生物相容性测试实验表明两性齐聚物修饰的Fe₃O₄纳米晶在各种生理环境中都能够稳定地存在, 并没有发生团聚现象.