芥子气纯度测定不确定度分析与评定

采用酸碱滴定法测定芥子气纯度,对测量结果的不确定度进行评定。分析了测定过程中不确定度来源,包括滴定剂的标定、消耗滴定剂体积、样品称量等引入的不确定度及其计算方法,最后合成得到标准不确定度。当芥子气纯度测定结果为94.78%时,扩展不确定度为0.34%(k=2)。实验结果表明,样品称量引入的不确定度对测量结果的影响最大。     

Development and validation of a RP-HPLC method for Roflumilast and its degradation products

Roflumilast is a phosphodiesterase type 4 inhibitor that is administered orally as a long-term, in the clinical treatment of chronic obstructive pulmonary disease and asthma. Launched in 2010 for the European market, it currently does not have an official monograph. Here, a reproducible gradient RP-HPLC method was developed and validated for the separation and determination of Roflumilast in the presence of its six major degradation products. Separation was performed on a C₁₈ analytical column (250?×?4.6?mm, 5?µm) with a mobile phase-A of ACN and a phase-B of ammonium acetate buffer (5?mM, pH 4.2) containing triethylamine (0.5% v/v). The most effective RP-HPLC gradient program was determined to be 0/80, 35/10, 36/80, 40/80 (time in minutes/% mobile phase-B). The flow rate was 1.0?ml/min and the column temperature was 25°C. The success of separation of the degradation products with different chemical characteristics was obtained by extending the time of the gradient, changing the proportion of the mobile phases and increasing the velocity of the flow. Two detectors were evaluated for the identification of degradation products and Roflumilast: a diode-arrary detector and a charged aerosol detector. The inability of the charged aerosol detector to dectect one of the six degradation products indicated that the method developed with RP-HPLC and the diode-array detector was more suitable for Roflumilast analysis. The method was validated according to specificity, linearity, LOD, LOQ, accuracy, precision and robustness.     

Supercritical fluid chromatography of petroleum products using flameless sulfur chemiluminescence detection

Supercritical fluid chromatography using flameless sulfur chemiluminescence detection has been investigated for the analysis of sulfur compounds in petroleum products. The chromatography and detection system was easy to implement and exhibited good precision, linearity, selectivity, and sensitivity. A minimum detectable limit of 0.3 pg sulfur/s was obtained, and response to sulfur in different sulfur species was nearly equimolar.     

SPE and HPLC/UV of resin acids in colophonium-containing products

A new method, involving SPE and HPLC/UV diode-array detection (DAD), was developed for the quantification of colophonium components in different consumer products, such as cosmetics. Colophonium is a common cause of contact dermatitis since its components can oxidize into allergens on exposure to air. Three different resin acids were used as markers for native and oxidized colophonium, abietic acid (AbA), dehydroabietic acid (DeA), and 7-oxodehydroabietic acid (7-O-DeA). The SPE method, utilizing a mixed-mode hydrophobic and anion exchange retention mechanism, was shown to yield very clean extracts. The use of a urea-embedded C(12) HPLC stationary phase improved the separation of the resin acids compared to common C(18). Concentrations higher than 2 mg/g of both AbA and DeA were detected in wax strips. In this product also 7-O-DeA, a marker for oxidized colophonium, was detected at a level of 28 microg/g. The LODs were in the range of 7-19 microg/g and the LOQs 22-56 microg/g. The method is simple to use and can be applied on many types of technical products, not only cosmetics. For the first time, a method for technical products was developed, which separates AbA from pimaric acid.     

HPLC method validation for measurement of sulforaphane level in broccoli by‐products

A simple and specific analytical method was developed and tested for the determination of sulforaphane in broccoli by‐products. The method includes the optimization of the conversion of glucoraphanin to sulforaphane, followed by purification of extracts using solid‐phase extraction and high‐performance liquid chromatography (HPLC) analysis. The response surface methodology was used to find optimum conditions for the preparation and purification procedure. Chromatographic conditions for reversed‐phase HPLC with UV photodiode array detection were as follows: column, Exil ODS C₁₈, 25 × 0.46 cm, 5 μm; column temperature, 36°C; mobile phase, a 30 : 70 (v/v) mixture of acetonitrile:water; flow rate, 0.6 mL/min. The detection wavelength was UV 202 nm. Under these conditions, excellent linearity was obtained (r² = 1), and the overall recovery was 97.5 and 98.1% for fresh florets and lyophilized florets, respectively. The precision results showed that the relative standard deviation of the repeatability for florets fresh and lyophilized was 3.0 and 4.0%, respectively. Sulforaphane contents were determined in the edible portion of fresh broccoli, and broccoli crop remains. Copyright © 2009 John Wiley & Sons, Ltd.     

Development and validation of HPLC method for determination of clotrimazole and its two degradation products in spray formulation

A novel simple isocratic HPLC method with UV detection for the determination of three compounds in spray solution (active component clotrimazole and two degradation products imidazole and (2-chlorophenyl)diphenylmethanol) using ibuprofen as an internal standard was developed and validated. The complications with different acido-basic properties of the analysed compounds in HPLC separation - while clotrimazole has pK_a 4.7, imidazole has pK_a 6.9 compared to relatively more acidic (2-chlorophenyl)diphenylmethanol - were finally overcome using a 3.5 μm Zorbax^® SB-Phenyl column (75 mm × 4.6 mm i.d., Agilent Technologies).The optimal mobile phase for separation of clotrimazole, degradation products imidazole and (2-chlorophenyl)diphenylmethanol and ibuprofen as internal standard consists of a mixture of acetonitrile and water (65:35, v/v) with pH* conditioned by phosphoric acid to 3.5. At a flow rate of 0.5 ml min⁻¹ and detection at 210 nm, the total time of analysis was less than 6 min.The method was applied for routine analysis (batch analysis and stability tests) in commercial spray solution.     

Improvements in monitoring the N-terminal valine adduct in human globin after exposure to sulfur mustard and synthesis of reference chemicals

The N-terminal valine adduct (HETE-Val) in globin is believed to behave as a long-lived biomarker after exposure to sulfur mustard (HD). Development of a highly sensitive method for monitoring HETE-Val, particularly at low HD exposure levels or for retrospective detection, would be a significant achievement. In this study, by improving the sample preparation method, a sensitive NCI-GC/MS method was established for the analysis of HETE-Val in globin after HD exposure. To optimize and investigate the sample preparation method, all the relevant HETE-Val chemicals were synthesized, purified, and characterized. By carrying out optimized solid phase extraction (SPE) cleanup followed by modified Edman degradation results in a low detection level and clean baseline. The minimum detectable exposure level of human blood (in vitro) to HD is 20 nmol/L (S/N > 3). The interday and intraday precisions of the proposed method were found to be acceptable with less than a 15% relative standard deviation (RSD). A nearly linear dose-effect relationship was observed between HETE-Val and a HD exposure concentration range of 0.1-120 μmol/L. The percentage of HD that reacted with N-terminal valine in globin obtained from human blood (in vitro) was quantified using the proposed method.     

Development of a tandem thin-layer chromatography-high-performance liquid chromatography method for the identification and determination of corticosteroids in cosmetic products

A solid-phase extraction clean-up and and a liquid chromatographic method with ultraviolet detection were developed for the analysis of 51 corticosteroids in cosmetic samples in order to screen commercial samples for the presence of undeclared synthetic corticosteroids. A thin-layer chromatographic analysis was carried out on silica gel plates, using different eluants and detection reagents. When such a preliminary chromatographic separation gave some indications about the presence of steroid compounds, the methanol extracts from real samples were applied to a solid-phase extraction C₁₈ cartridge, and the analytes eluted with ethyl ether. The high-performance liquid chromatographic separation was then carried out for the identification and determination of the analytes using a Purospher RP-18 column, an isocratic or a gradient elution with a mixture acetonitrile-water and a photodiode-array detector. The accuracy of the method was determined by spiking experiments on home-made cosmetic samples. The analytical recoveries were satisfactory.     

Forced degradation studies of norepinephrine and epinephrine from dental anesthetics: Development of stability-indicating HPLC method and in silico toxicity evaluation

Injectable solutions containing epinephrine (EPI) and norepinephrine (NE) are not stable, and their degradation is favored mainly by the oxidation of catechol moiety. As studies of these drugs under forced degradation conditions are scarce, herein, we report the identification of their degradation products (DP) in anesthetic formulations by the development of stability-indicating HPLC method. Finally, the risk assessment of the major degradation products was evaluated using in silico toxicity approach. HPLC method was developed to obtain a higher selectivity allowing adequate elution for both drugs and their DPs. The optimized conditions were developed using a C18 HPLC column, sodium 1-octanesulfonate, and methanol (80:20, v/v) as mobile phase, with a flow rate of 1.5 mL/min, UV detection at 199 nm. The analysis of standard solutions with these modifications resulted in greater retention time for EPI and NE, which allow the separation of these drugs from their respective DPs. Then, five DPs were identified and analyzed by in silico studies. Most of the DPs showed important alerts as hepatotoxicity and mutagenicity. To the best of our acknowledgment, this is the first report of a stability-indicating HPLC method that can be used with formulations containing catecholamines.     

Determination of potential degradation products of piroxicam by HPTLC densiometry and HPLC

Summary HPTLC densitometry and HPLC are considered for the simultaneous determination of the degradation products of piroxicam (2-aminopyridine, DP-I and DP-II). The substances were separated on silica gel with fluorescence indicator in ethylacetate — toluene — diethylamine (10∶10∶5) and toluene — absolute ethanol — glacial acetic acid (8∶1.2∶0.5) systems. The measuring absorbance (detection of reflectance) of the separated substances was carried out “in situ” at 296 nm using 4-level calibration (external standard, nonlinear regresson function) in the concentration range 600–1200 ng 2-aminopyridine/spot and 300–600 ng DP-I and DP-II/spot. The HPLC method was carried out using RP-8 stationary phase and methanol + phosphate-citrate buffer, pH 3 mobile phase with addition of sodium pentanesulfonate (40+60, v/v). 2-aminopyridine wass detected at 300 nm, DP-I at 280 nm and DP-II at 248 nm. The concentration range for 2-aminopyridine is 2–40 μg/ml, for DP-I and DP-II 2–20 μg/ml (for an injection volume of 10 μl). The results were evaluated by linear regression analysis.     

Validated HPLC method for the determination of fluconazole in human plasma

A high-performance liquid chromatographic assay with UV detection was developed for the determination of fluconazole in human plasma. The method utilized solid-phase extraction for sample clean-up. The separation was performed on a C18 column by isocratic elution with a mobile phase of 10 mM acetate buffer at pH 5.0 and methanol and UV detection at 210 nm. Validation was performed according to the current recommendations of the USFDA bioanalytical method validation guidance. The method proved to be specific, accurate, precise and linear between 200 and 10,000 ng/mL with correlation coefficients greater than 0.999. The coefficient of variation was within 11% and relative deviation was less than 10%.     

Screening hydrolysis products of sulfur mustard agents by high-performance liquid chromatography with inductively coupled plasma mass spectrometry detection

Sulfur mustard (HD), bis(2-chloroethyl)sulfide, is one of a class of mustard agents which are chemical warfare agents. The main chemical warfare hydrolysis degradation products of sulfur mustards are: thiodiglycol, bis(2-hydroxyethylthio)methane, 1,2-bis(2-hydroxyethylthio)ethane, 1,3-bis(2-hydroxyethylthio)propane, and 1,4-bis(2-hydroxyethylthio)butane. The aim of this study is to identify these five hydrolysis degradation products utilizing reversed-phase high-performance liquid chromatography coupled with inductively coupled plasma mass spectrometry (ICP-MS) for element-specific sulfur detection using a collision/reaction cell and electrospray ionization mass spectrometry to confirm the identification. To date, this is the first study utilizing ICP-MS with ³²S element-specific detection for the analysis of vesicant chemical warfare agent degradation products.     

Assessing the degradation profile of functional aliphatic polyesters with precise control of the degradation products

The pre-polymer poly(but-2-ene-1,4-diyl malonate) (PBM) and a series of PBM-based materials are shown to be degradable under physiological conditions in vitro and they are therefore presented as potential materials for biomedical applications. Four different PBM-based materials are synthesized: a PBM homopolymer, crosslinked PBM with and without spacer, and a triblock copolymer of PBM and PLLA with the PBM as an amorphous middle block. The polymers are subjected to hydrolytic degradation in phosphate-buffered saline at pH = 7.4 and 37 °C. The results show that all the PBM-based materials degrade without a rapid release of acidic degradation products or any substantial lowering of the pH that might jeopardize their biocompatibility.     

Electrochemical,fluorescence, and UV detection for HPLC analysis of various cysteine derivatives

Electrochemical (ECD), fluorescence (FLD), and UV spectrophotometric (UVD) detection were used to monitor various S-alk(en)yl-L -cysteines and their corresponding sulfoxide isomers following pre-column derivatization with o-phthaldialdehyde-tert-butylthiol and separation by reversed-phase HPLC. Recording of hydrodynamic voltammograms, FLD stop-flow scanning, and on-line captured UV spectra were methods used for establishing optimal detector settings which were defined as a compromise between favorable selectivity and high sensitivity. Optimal detector settings were found at: (A) 750 mV vs. Ag/AgCl for ECD; (B) excitation at 230 nm and emission at 420 nm for FLD; and (C) 337 nm for UVD. Various aspects of detector practicability such as selectivity, baseline disturbances due to excessive reagent, scanning possibilities, as well as detection limits were evaluated and compared. Minimal detectable amounts of the compounds were in the range of 130-160 fmol for ECD, and 2.5-3.5 pmol and 13-16 pmol for FLD and UVD. In addition, the possibilities and benefits of detector coupling were examined.     

Quantitative reversed phase HPLC analysis of L-ascorbic acid (Vitamin C) and identification of its degradation products

Summary An isocratic ion suppression reversed phase method is utilized for the qualitative and quantitative determination of L-ascorbic acid in fresh fruit juices — complex sample matrices. The selectivity of the method, when a macroreticular poly(styrene-divinylbenzene) reversed phase adsorbent is used, is sufficient to resolve the isomers L-ascorbic acid and D-erythorbic acid (isoascorbic acid) to baseline in under 8 minutes. L-Ascorbic acid solution stability is monitored using the same analytical conditions with the degradation products sufficiently well resolved not to interfere in the quantification of L-ascorbic acid. By the use of commercial materials and the preparation of the proposed products of the oxidative degradation of L-ascorbic acid the degradation sequence and identification of the products in an aged L-ascorbic acid solution is accomplished.     

Development and validation of a capillary electrophoresis method applied to the analysis of l‐citrulline in an oral formulation for pediatric use

A simple and highly sensitive CE–UV method was applied in the determination of l ‐ctrulline, which was developed from an oral formulation for pediatric use. The novel method was based on the analysis of l ‐citrulline for direct ultraviolet detection at 198 nm. The BGE consisted of 10 mM sodium tetraborate and 50 mM SDS at pH 9, and the electrophoretic parameters were optimized. The method was validated in terms of specificity, linearity, LOD, LOQ, precision, accuracy, and robustness. The LOD and LOQ obtained were 1.36 and 4.54 μg/mL, respectively. In addition, the method offers higher sensitivity and specificity compared with the results obtained from HPLC method using UV‐detectors, in which l‐ citrulline needs to be derivatizated. Furthermore, low cost and simplicity of the system allowed the rapid and simple quantitation of l‐ citrulline in the oral formulation for quality control and stability indicated method.     

Stability-indicating HPLC method for the determination of nicardipine in capsules and spiked human plasma. Identification of degradation products using HPLC/MS

In this stability-indicating, reversed-phase high-performance liquid chromatographic method for nicardipine (NIC), forced degradation has been employed and the formed degradants were separated on a C18 (150 mm × 3.9 mm, 5 μm) analytical column using a mobile phase consisted of 70% methanol: acetic acid containing 0.01 M triethylamine with pH 4. The flow rate was 1.0 mL/min and the photodiode array detection wavelength was 353 nm. Forced degradation of the drug was carried out under acidic, basic, photolytic, and oxidative stress conditions. Chromatographic peak purity data indicated no co-eluting peaks with the main peaks. This method resulted in the detection of seven degradation products. Among these, two major degradation products from basic hydrolysis, one from oxidation by H₂O₂ and four from photolytic stress were identified by mass spectral data. A good linear response was achieved over the range of 0.5–40 μg/mL with a limit of detection (LOD) of 0.011 μg/mL and limit of quantification (LOQ) of 0.036 μg/mL. The suggested method was successfully applied for the analysis of NIC in its commercial capsules, with mean% recovery value of 100.11 ± 2.26%. The method was extended to the in vitro determination on NIC in spiked human plasma samples with mean% recovery of 99.04 ± 5.67%. The suggested method was utilized to investigate the kinetics of photolytic induced degradation.     

Application of MEKC and monolithic CEC for the analysis of bioactive naphthoquinones in Eleutherine americana

Two microscale separation techniques for the analysis of bioactive naphthoquinones in Eleutherine americana were developed and validated. By MEKC four compounds (eleuthoside B, isoeleutherin, eleutherol and eleutherinoside A) could be determined in plant extracts using an aqueous electrolyte solution composed of 25 mM sodium tetraborate, 50 mM sodium cholate and 20% THF. CEC on a polymeric methacrylate‐based monolith with strong cationic properties showed promising results, as it additionally enabled the separation of two enantiomers, eleutherin and isoeleutherin. The mobile phase for CEC experiments comprised 3 mM ammonium formate in a mixture of ACN and water. At an applied voltage of ?25 kV, all five markers were baseline separated in less than 12 min. Both methods were successfully validated for linearity (MEKC: R²≥0.999; CEC: R²≥0.997), sensitivity (MEKC: LOD=4–5 μg/mL; CEC: LOD=2–8 μg/mL), accuracy (MEKC: 96.5–102.7% recovery; CEC: 97.1–103.5% recovery) and precision (MEKC: σ_rel≤2.43%; CEC: σ_rel≤2.21%). The quantitative analysis of naphthoquinone derivatives in several E. americana samples showed that both methods are suitable for practical applications, because the results were well comparable to those obtained by established techniques such as HPLC.     

Development and validation of a stability-indicating HPLC method for the determination of degradation products in dipyridamole injection

Summary The development and subsequent validation of an isocratic high-performance liquid chromatographic (HPLC) procedure employing ultraviolet (UV) detection for the determination of degradation products in Dipyridamole Injection is reported. The development of this assay involved the evaluation of several factors including buffer type, ionic strength, pH, organic composition, and column type. The described method is simple, reproducible, accurate, and selective. The precision, relative standard deviation (RSD), amongst five sample preparations for total degradation products was not more than (NMT) 10.2 %, while the individual degradation products were NMT 12.1%. Intermediate precision, as determined from fifteen sample preparations, generated by two Analysts on different HPLC systems over three days, exhibited an RSD for total and individual degradation products of 8.2 % and NMT 27.5 %, respectively. The mean absolute recovery of dipyridamole using the described method is 102.1±1. 9%, (mean±SD, n=12) over the concentration range of 0.03 % to 5.0 % of its label claim of 5 mg mL⁻¹. The limit of detection and limit of quantitation were 0.1 and 0.3 μg mL⁻¹, respectively. The linearity of the peak response was verified with respect to dipyridamole concentration over a range of 0.3 and 50 μg mL⁻¹ (0.03 % to 5.0 % label claim). The Standard and Assay Preparations are stable for up to 48 hours at room temperature. The selectivity was evaluated by subjecting the finished product (Dipyridamole Injection) to thermal, acidic, basic, oxidative and fluorescent radiation stress conditions. No interference in the analysis of degradation products was observed, showing the method is stability-indicating.     

Simultaneous HPLC determination of 14 tricyclic antidepressants and metabolites in human plasma

A HPLC method has been developed for the simultaneous determination of seven tricyclic antidepressants (TCAs) and seven metabolites in human plasma. The analyte separation was obtained using a C8 reversed phase column and a mobile phase composed of 68% aqueous phosphate buffer at pH 3.0 and 32% ACN. The UV detector was set at 220 nm and loxapine was used as the internal standard. A careful pre‐treatment procedure for plasma samples was developed, using SPE on C2 cartridges, which gives satisfactory extraction yields (>80%) and good sample purification. The LOQs were always lower than 9.1 ng/mL and the LODs always lower than 3.1 ng/mL for all analytes. The method was successfully applied to plasma samples from depressed patients undergoing therapy with one or more TCA drugs. Precision data (RSD <8.1%), as well as accuracy results (recovery >80%), were satisfactory and no interference from other drugs was found. Hence the method seems to be suitable for the therapeutic drug monitoring of patients treated with TCAs under monotherapy or polypharmacy regimens.