Selective Determination of Verapamil in Pharmaceutics and Urine Using a Boron‐doped Diamond Electrode Coupled to Flow Injection Analysis with Multiple‐pulse Amperometric Detection

This work presents a simple and low‐cost method for fast and selective determination of Verapamil (VP) in tablets and human urine samples using a boron‐doped diamond working electrode (BDD) coupled to a flow injection analysis system with multiple pulse amperometric detection (FIA‐MPA). The electrochemical behaviour of VP in 0.1 mol L⁻¹ sulfuric acid showed three merged oxidation peaks at around +1.4 V and upon reverse scan, one reduction peak at 0.0 V (vs. Ag/AgCl). The MPA detection was performed applying a sequence of three potential pulses on BDD electrode: (1) at +1.6 V for VP oxidation, (2) at +0.2 V for reduction of the oxidized product and (3) at +0.1 V for cleaning of the working electrode surface. The FIA system was optimized with injection volume of 150 μL and flow rate of 3.5 mL min⁻¹. The method showed a linear range from 0.8 to 40.0 μmol L⁻¹ (R>0.99) with a low limit of detection of 0.16 μmol L⁻¹, good repeatability (RSD<2.2 %; n=10) and sample throughput (45 h⁻¹). Selective determination of VP in urine was performed at+0.2 V due to absence of interference from ascorbic and uric acids in this potential. The addition‐recovery tests in both samples were close to 100 % and the results were similar to an official method.     

Carbon‐nanotube Modified Screen‐printed Electrode for the Simultaneous Determination of Nitrite and Uric Acid in Biological Fluids Using Batch‐injection Amperometric Detection

A portable electroanalytical system applied for rapid and simultaneous determination of uric acid (UA) and nitrite (NIT) in human biological fluids (urine, saliva and blood) is reported. The system is based on batch‐injection analysis with multiple‐pulse amperometric (BIA‐MPA) detection using screen‐printed electrodes (SPEs) modified with multi‐walled carbon nanotubes. Sample dilution in optimized electrolyte (0.1 mol L⁻¹ Britton‐Robinson buffer pH 2) followed by injection of 100 μL on the electrode surface using an electronic micropipette is performed. UA is detected at +0.45 V and both UA+NIT at +0.70 V. Linear calibration plots for UA and NIT were obtained over the range of 1–500 μmol L⁻¹ with detection limits of 0.05 and 0.06 μmol L⁻¹, respectively. For comparison, a differential‐pulse voltammetric (DPV) method was optimized, and linear calibration plots for UA and NIT were obtained over range of 1–30 μmol L⁻¹ and 1–40 μmol L⁻¹ with detection limits of 0.1 and 0.3 μmol L⁻¹, respectively. BIA‐MPA is highly precise (RSD<1.3 %), fast (160 h⁻¹) and free from sample‐matrix interferences as recovery values ranged from 77 to 121 % for spiked samples (short contact time of sample aliquot with SPE). Contrarily, recovery tests conducted using DPV did not provide adequate recovery values (>150 %), probably due to the longer contact time of the SPE with the biological samples during analysis leading to a severe interference of sample matrices.     

Fast and Simple Electrochemical Analysis Kit for Quality Control of Narrow Therapeutic Index Drugs

The use of multiple‐pulse amperometry (MPA) for the determination of narrow therapeutic index (NTI) drugs using batch injection analysis (BIA) with carbon screen‐printed electrodes (SPE) is proposed, seeking to develop a practical and low‐cost analysis kit for application in routine quality control of these drugs. The electrochemical behaviors of aminophylline, carbamazepine, clindamycin, colchicine, minoxidil, prazosin, procainamide, theophylline, warfarin and verapamil were evaluated in different electrolytes, but just one, the 0.1 mol L⁻¹ phosphate buffer, pH 7.0, was chosen for determination of all the analytes. The amperometric detection was optimized as a function of the best oxidation potential for carbon SPE for each analyte, which was in a range from 0.7 to 1.1 V. The injection conditions were determined as a function of the velocity and the volume injected by the BIA system, which were 92.5 μL s⁻¹ and 100 μL, respectively. Under these conditions, a good repeatability (RSD<3 %), high analytical frequency (>215 determinations per hour), large linear ranges and low LOD (<0.42 μmol L⁻¹) for all the NTI drugs were obtained. Furthermore, the proposed method provided an easy qualitative analysis of the investigated analytes using MPA detection. The addition‐recovery studies in pharmaceutical samples containing NTI drugs and the comparison with official methods showed that the proposed analysis Kit is a very fast, simple and efficient alternative for quantification of these analytes.     

Fast and Selective Simultaneous Determination of Acetaminophen,Aspirin and Caffeine in Pharmaceutical Products by Batch Injection Analysis with Multiple Pulse Amperometric Detection

In this work is presented a method for simultaneous determination of paracetamol (PA), acetylsalicylic acid (ASA) and caffeine (CA) in pharmaceutical tablets, using a bare boron‐doped diamond working electrode (BDDE) coupled to batch injection analysis system with multiple pulse amperometric detection (BIA‐MPA). The optimized sequence of fast potential pulses were applied on BDDE for acquisition of independent amperograms: +1.0 V for PA oxidation, +1.3 V for oxidation of PA and salicylic acid (SA) generated from a previous alkaline hydrolysis of ASA and +1.6 V in which the three analytes are oxidized (PA, SA and CA). Selective determination of PA is performed using the currents obtained at +1.0 V, while SA and CA signals are indirectly obtained using simple subtraction operations between peak currents from each amperogram and correction factors (CF's). The limitations of such approach on the precision and accuracy as function of BIA‐MPA conditions are discussed. Simultaneous determination of the target drugs in pharmaceutical tablets was performed by BIA‐MPA and the results compared to a HPLC‐DAD method. Under optimized conditions, the proposed method exhibits fast responses (180 injections per hour for the simultaneous determination of the three analytes) and suitable precision (RSD_PA: 0.78 %; RSD_SA: 1.09 %; RSD_CA: 2.73 %). BIA‐MPA method is simple, portable and presents relative low‐cost.     

Batch‐injection versus Flow‐injection Analysis Using Screen‐printed Electrodes: Determination of Ciprofloxacin in Pharmaceutical Formulations

This article highlights the potential use of multi‐walled carbon‐nanotube modified screen‐printed electrodes (SPEs) for the amperometric sensing of ciprofloxacin and compares the association of batch‐injection analysis (BIA) and flow‐injection analysis (FIA) with amperometric detection. Both analytical systems provided precise (RSD<5 %) and sensitive determination of ciprofloxacin (LOD<0.1 μmol L^?1) within wide linear range (up to 200 μmol L^?1). Accuracy of both methods was attested by recovery values (93–107 %) and comparison with capillary electrophoresis. The BIA system is completely portable (especially due to association with SPEs) and provided faster analyses (130 h^?1) and more sensitive detection than the FIA system due to the higher flow rates of injection.     

Electrochemical Oxidation of Ibuprofen and Its Voltammetric Determination at a Boron‐Doped Diamond Electrode

The electrochemical oxidation of ibuprofen at a boron‐doped diamond electrode (BDDE) and its voltammetric determination is reported for the first time. A well‐defined oxidation peak was observed at around 1.6 V in 0.1 mol L^?1 H₂SO₄ solution with 10 % (v/v) ethanol at the BDDE surface activated by either cathodic or anodic pretreatments. A differential‐pulse voltammetric method for the determination of ibuprofen in pharmaceutical formulations was optimized with a detection limit of 5 µmol L^?1 and compared with the British Pharmacopeia method.     

Development of a Novel Versatile Method for Determination of two Antihistamines in Association with Naphazoline Using Cathodically Pretreated Boron‐doped Diamond Electrode

Antihistamines such as pheniramine (PHN) or chlorpheniramine (CPH) are commonly associated with naphazoline (NPZ) in eye drops and nasal decongestants. In this work, a batch‐injection analysis system with multiple pulse amperometric (BIA‐MPA) detection has been applied for the first time for fast simultaneous determination of naphazoline (NPZ) and pheniramine (PHN) or NPZ and chlorpheniramine (CPH). PHN or CPH was selectively detected at +1.1 V and both PHN and NPZ or CPH and NPZ were detected at +1.3 V using boron doped diamond (BDD) as working electrode and Britton‐Robinson (BR) buffer (pH=10.0) as supporting electrolyte. The current of NPZ can then be obtained by subtraction of the currents detected at both potential pulses and applying a correction factor (CF). The proposed method presented good intra‐day repeatability (RSD between 0.7 and 3.2 % for PHN; 0.7 and 2.1 % for CPH; 1.5 and 4.0 % for NPZ; n=20), high analytical frequency (>80 injections h⁻¹), and limits of detection of 0.64, 0.47 and 0.11 μmol L⁻¹ for PHN, CPH and NPZ, respectively. The results obtained with the proposed method are in agreement with those obtained by HPLC (95 % confidence level).     

A Simple Strategy for Simultaneous Determination of Paracetamol and Caffeine Using Flow Injection Analysis with Multiple Pulse Amperometric Detection

In this work, we report a simple and novel strategy for simultaneous analysis using flow injection analysis with multiple pulse amperometric (FIA‐MPA) detection. The proposed strategy was successfully used for simultaneous determination of paracetamol and caffeine (model analytes) in pharmaceutical formulations. A sequence of potential pulses (waveform) was selected in such a way that PA is selectively oxidized at E₁ (+1.20 V/50 ms) and both compounds (PA+CA) are simultaneously oxidized at E₂ (+1.55 V/50 ms); hence, current subtraction (using a correction factor) can be used for the selective determination of CA. The proposed FIA method is simple, cheap, fast (140 injections h^?1), and present selectivity for the determination of both compounds in pharmaceutical samples, with results similar to those obtained by HPLC at a 95 % confidence level.     

Fast Determination of Ciprofloxacin by Batch Injection Analysis with Amperometric Detection and Capillary Electrophoresis with Capacitively Coupled Contactless Conductivity Detection

We report fast, precise, selective, and sensitive electroanalytical methods for the determination of ciprofloxacin in milk and pharmaceutical samples by batch‐injection analysis with amperometric detection (BIA‐AMP) and by capillary electrophoresis with capacitively‐coupled contactless conductivity detection (CE‐C⁴D). Both methods required simple sample preparation protocols before analysis (milk samples were just diluted and tablets powdered and dissolved in electrolyte/water). The analytical features of BIA‐AMP and CE‐C⁴D methods include, respectively, low relative standard deviation values for repetitive measurements (2.8 % and 1.7 %, n=10), low detection limits (0.3 and 5.0 µmol L^?1), elevated analytical frequency (80 and 120 h^?1) and satisfactory accuracy (based on comparative determinations by HPLC and recovery values for spiked samples).     

FIA Determination of Paracetamol in Pharmaceutical Drugs by Using Gold Electrodes Modified with a 3‐Mercaptopropionic Acid Monolayer

A flow injection analysis (FIA) method for the determination of paracetamol in pharmaceutical drugs using a gold electrode modified with a self‐assembled monolayer (SAM) of 3‐mercaptopropionic acid is described. At optimized experimental conditions the dynamic concentration range was 0.15 to 15.0 mg L^?1 with a detection limit of 0.2 μg mL^?1 (S/N=3). The repeatability of current responses for injections of 10 μmol L^?1 paracetamol was evaluated to be 3.2% (n=30) and the analytical frequency was 180 h^?1. The lifetime of the modified electrode was found to be 15 days. The results obtained by using the proposed amperometric method for paracetamol determination in four different drug samples compared well with those found by spectrophotometry.     

Voltammetry as the First Method for Direct Determination of a Novel Antagonist of A2A Adenosine Receptors

In this article, for the first time, the analytical method for determination of a novel antagonist of A_2A adenosine receptors (8‐(4‐methoxyphenyl)‐4‐oxo‐4,6,7,8‐tetrahydroimidazo[2,1‐c][1,2,4]triazine‐3‐carbohydrazide, namely IMT), which can be used as a drug for liver diseases, was presented. For this purpose a commercially available boron‐doped diamond electrode (BDDE) in combination with differential pulse voltammetry (DPV) was applied. It was found by cyclic voltammetry (CV) that IMT displays at BDDE, as a sensor, two well‐defined oxidation peaks at potentials of 0.81 and 1.18 V and one reduction peak at 1.1 V vs. Ag/AgCl in 0.1 mol L^?1 acetate buffer (pH 4.5±0.1). The oxidation and reduction mechanism of IMT was proposed. The developed DPV method allowed the successful determination of IMT in the range of 0.05–50 μmol L^?1 with detection limit equal to 0.0094 μmol L^?1 and without any chemical modifications and electrochemical pretreatment of the electrode surface. The proposed procedure allows the determination of IMT in vitro directly from urine samples.     

Determination of Amlodipine and Atenolol by Batch Injection Analysis with Amperometric Detection on Boron‐doped Diamond Electrode

This work describes the sequential determination of amlodipine (AML) and atenolol (ATN) by batch injection analysis (BIA) with pulsed amperometric detection (BIA‐PAD). Boron doped diamond (BDD) was used as working electrode. AML was detected at +1.00 V and ATN at +1.65 V. The proposed BIA method is simple, robust, precise (RSD <3.2 %; n=10), presents high analytical frequency (>70 injections h^?1), generates reduced volume of waste (without use of organic solvent) and requires minimal sample manipulation (dissolution and dilution in electrolyte). The limits of detection were 0.074 and 0.073 µmol L^?1 for AML and ATN, respectively. The results obtained with the proposed BIA method were compared to those obtained by HPLC and similar results were obtained (at 95% of confidence level).     

Flow‐Injection Pulsed‐Amperometric Determination of Free Glycerol in Biodiesel at a Gold Electrode

This work reports the highly‐sensitive amperometric determination of free glycerol in biodiesel at a gold electrode adapted in a flow‐injection analysis (FIA) cell. The amperometric method involved the continuous application of three sequential pulses to the working electrode (+250 mV, +700 mV, and ?200 mV, for 100 ms each). This sequence of potential pulses eliminated electrode passivation and dramatically increased the analytical signal. The proposed FIA‐amperometric method presented low relative standard deviation between injections (1.5 %, n=15), high analytical frequency (85 h^?1), satisfactory recovery values (93–118 %) for spiked samples, wide linear range (from 1 to 300 µmol L^?1), and low detection limit (0.5 µmol L^?1).     

Development of Electroanalytical Methods Using Different Electrodes for the Determination of Progesterone (P4) in Pharmaceutical Formulations and Human,Cow and Goat Milk

For the determination of progesterone (P4) electroanalytical studies were performed using mercury electrode (HMDE) and screen-printed boron-doped diamond electrode (BDD-SPE). The effects of pH, supporting electrolyte, accumulation potential and time (E_acc, t_acc) were studied in both systems. The optimum conditions were: i) HMDE: pH 7,0; E_acc: −0,1 V and t_acc: 40 s, ii) BDD-SPE: 0,5 mol L⁻¹ H₂SO₄; E_acc: 0,0 V and t_acc: 120 s. Under these conditions, the detection limit was 3.1 μg L⁻¹ for HMDE and 45.6 μg L⁻¹ for BDD-SPE. Both methods were validated and applied in the P4 determination on pharmaceutical formulations and milk samples.     

Nanostructured Hexacyanoferrate Intercalated Ni/Al Layered Double Hydroxide Modified Electrode as a Sensitive Electrochemical Sensor for Paracetamol Determination

An electrochemical sensor for paracetamol (PC) based on the hexacyanoferate(III) intercalated Ni−Al layered double hydroxide (Ni−Al−HCF) was presented. The as‐prepared LDH structurally and morphologically was characterized by scanning electron microscopy, X‐ray diffraction, and Fourier transform IR. Electrochemical studies revealed that Ni−Al−HCF film modified glassy carbon (GC) electrode exhibited remarkable electrocatalytic activity toward the oxidation of paracetamol. The electrochemical behavior of PC on the Ni−Al−HCF film was investigated in detail. Under optimum experimental conditions, the electrocatalytic response of the modified GC electrode was linear in the PC concentration range 3×10⁻⁶⁻–1.5×10⁻³ mol L⁻¹, with a detection limit of 8×10⁻⁷ mol L⁻¹ (S/N=3), using hydrodynamic amperometry. In addition, the modified electrode exhibited good reproducibility, long‐term stability and anti‐interference property. The fabricated sensor was successfully applied to determination of PC in various pharmaceutical preparations such as tablets, oral solution, and oral drops. Finally, the method was validated by the analysis of paracetamol spiked human serum samples, and good recoveries were obtained in the range of 99.2–103 %.     

Simultaneous Electrochemical Determination of Hydroquinone and Bisphenol A using a Carbon Paste Electrode Modified with Silver Nanoparticles

In this paper, a rapid and sensitive modified electrode for the simultaneous determination of hydroquinone (HQ) and bisphenol A (BPA) is proposed. The simultaneous determination of these two compounds is extremely important since they can coexist in the same sample and are very harmful to plants, animals and the environment in general. A carbon paste electrode (CPE) was modified with silver nanoparticles (nAg) and polyvinylpyrrolidone (PVP). The PVP was used as a reducing and stabilizing agent of nAg from silver nitrate in aqueous media. The nAg‐PVP composite obtained was characterized by transmission electron microscopy and UV‐vis spectroscopy. The electrochemical behavior of HQ and BPA at the nAg‐PVP/CPE was investigated in 0.1 mol L⁻¹ B−R buffer (pH 6.0) using cyclic voltammetry (CV) and square wave voltammetry (SWV). The results indicate that the electrochemical responses are improved significantly with the use of the modified electrode. The calibration curves obtained by SWV, under the optimized conditions, showed linear ranges of 0.09–2.00 μmol L⁻¹ for HQ (limit of detection 0.088 μmol L⁻¹) and 0.04–1.00 μmol L⁻¹ for BPA (limit of detection 0.025 μmol L⁻¹). The modified electrode was successfully applied in the analysis of water samples and the results were comparable to those obtained using UV‐vis spectroscopy.     

3D‐printed Microfluidic Device Based on Cotton Threads for Amperometric Estimation of Antioxidants in Wine Samples

The present work describes the evaluation of microfluidic electroanalytical devices constructed by a 3D printer using ABS (acrylonitrile butadiene styrene) polymer combined with cotton threads as microchannels. Screen‐printed carbon electrodes (SPCEs) were used as electrochemical detector for amperometric determination of gallic and caffeic acid in wine samples. Using optimal experimental conditions (flow rate of 0.71 μL s⁻¹, applied potential of +0.30 V and volume of injection of 2.0 μL) the proposed method presented a linear response for a concentration range of 5.0×10⁻⁶ to 1.0×10⁻³ mol L⁻¹. The detection limits for gallic and caffeic acid were found to 1.5×10⁻⁶ mol L⁻¹ and 8.0×10⁻⁷ mol L⁻¹, respectively, with a sample throughput of 43 h⁻¹. The achieved results are in agreement with those found using the official Folin‐Ciocaulteu method.     

Development of a Simple and Fast Electrochemical Method for Screening and Stoichiometric Determination of Dimenhydrinate

Dimenhydrinate (DIM) is a salt composed by the combination of two active pharmaceutical ingredients: diphenhydramine (DIP) and 8‐chlorotheophylline (CTP). In this work, the use of batch injection analysis with multiple pulse amperometric detection (BIA‐MPA) was proposed for the first time for fast stoichiometric determination of DIM. DIP (cation) and CTP (anion) were determined simultaneously in pharmaceutical samples with a simple and fast injection procedure (70 injections h^?1). Additional strategies were also proposed for rapid screening of samples containing the DIM salt. By a simple injection of a sample into the BIA system (without using of calibration curve), reliable information about stoichiometry of the DIM salt (1 : 1; DIP:CTP) and presence or absence of interfering species (electroactive) can be achieved.     

Determination of Benzocaine and Tricaine in Fish Fillets Using BIA with Amperometric Detection

A system based on batch injection analysis (BIA) associated with amperometric detection at screen‐printed carbon electrode was used for the precise and rapid quantification of the anesthetics compounds benzocaine and tricaine in fresh fish fillets. Along this study, the best conditions for the BIA‐amperometry system were stablished for the rapid determination of these compounds. The results obtained demonstrate that the proposed method is an interesting alternative to the chromatographic methods, once it allows to perform rapid analysis (more than 300 injections per hour) with low limits of detection (3.02×10⁻⁸ mol L⁻¹ for benzocaine and 3.19×10⁻⁸ mol L⁻¹ for tricaine), using just 80 μL of sample for each analysis. Furthermore, it was possible to obtain high repeatability for both compounds analyzed, demonstrating good performance. The simple sample preparation developed in this study drastically reduced the amount of fat in the fish extract, favoring precision, as shown by the results of the recovery studies of both anesthetics contained in the fish samples (values above 99 % for both analytes).     

Sensitive Voltammetric Determination of Methyl Parathion Using a Carbon Paste Electrode Modified with Mesoporous Zirconia

A mesoporous zirconia modified carbon paste electrode was developed for electrochemical investigations of methyl parathion (MP, Phen‐NO₂). The significant increase of the peak currents and the improvement of the redox peak potential indicate that mesoporous zirconia facilitates the electronic transfer of MP. The oxidation peak current was proportional to the MP concentration in the range from 1.0×10⁻⁸ to 1.0×10⁻⁵ mol L⁻¹ with a detection limit of 4.6×10⁻⁹ mol L⁻¹ (S/N=3) after accumulation under open‐circuit for 210 s. The proposed method was successfully applied to the determination of MP in apple samples.