首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
张国荣  李文华 《分析化学》1998,26(10):1254-1256
非成瘾性高效镇痛新药痛力克在硫酸底液中产生一灵敏的微分吸附计时电位溶出峰,峰电位在-1.0V。利用该峰测定痛力克的线性范围为0.02-2.0mg/L,检测限为0.004mg/L。用线性扫描,循环伏安等方法研究了该体系的电化学行为和电极反应机理,认为所研究体系属于有吸附性的不可逆还原过程,电极反应的电子转移数为2,参与电极反应的质子数为2。用该方法测定了片剂中痛力克的含量,结果满意。  相似文献   

2.
    
A novel, stable and sensitive non‐enzymatic sensor was developed with metal‐organic frameworks (MOFs) that have attracted great attention in electrochemical sensors applications in recent years. The pore structures of MIL (Fe)‐101 and MIL (Fe)‐53 are the families of MOFs that were constructed via a simple solvothermal procedure. The 35MIL‐101(Fe)‐reduced graphene oxide nanocomposite has been used for modification of glassy carbon electrode for the determination of carbofuran (CBF) and carbaryl (CBR). The porosity of the composites increased the voltammetric responses significantly for CBF and CBR in a mixed solution that makes the simultaneous determination of both carbamate pesticides possible. Characterization of MIL (Fe)‐101 and MIL (Fe)‐53 were performed with FT‐IR, XRD, BET and SEM. Finally, the introduced sensor under the optimal conditions showed low detection limits of 1.2 and 0.5 nM within the linear ranges of 5.0–200.0 nM and 1.0–300.0 nM for CBF and CBR, respectively. The non‐enzymatic sensor was successfully used to monitoring of carbamates residue in vegetable and fruit samples.  相似文献   

3.
Two sensitive and selective potentiometric sensors based on zinc-iron layered double hydroxides/multiwalled carbon nanotubes (Zn−Fe LDH/MWCNTs) (sensor I) and graphene/multiwalled carbon nanotubes (Gr/MWCNTs) (sensor II) nanocomposites were developed for benzydamine hydrochloride (Benz) determination. The investigated sensors displayed excellent Nernstian slopes 58.5±0.7 and 59.5±0.5 mV decade−1, detection limits 8.3×10−7 and 1.9×10−7 mol L−1, long lifetimes, adequate selectivity, high chemical, and thermal stability within pH range of 2.4–8.5 for sensors І and ІІ, respectively. The surface morphology of sensors was analyzed using a Transmission Electron Microscope (TEM). The analytical method was efficiently implemented for Benz determination in biological fluids and surface water samples.  相似文献   

4.
This paper studied the electrochemical sensors based on C? C bonding of graphene oxide (GO) on π‐conjugated aromatic group modified gold electrodes for simultaneous detection of heavy metal ions. For comparison, another sensing interface Au‐Ph‐NH‐CO‐GO, in which GO was modified to Au‐Ph‐NH2 interfaces by amide bonding. On the basis of the principle of heavy metal ions complexation with oxygenated species on GO, the fabricated sensing interfaces were used for the simultaneous determination of Pb2+, Cu2+ and Hg2+. The performance of two sensing interfaces for simultaneous detection of three metal ions was compared. Au‐Ph‐GO sensing interface demonstrated higher sensitivity and better repeatability than Au‐Ph‐NH‐CO‐GO sensing interface.  相似文献   

5.
The graphene nanosheets/manganese oxide nanoparticles modified glassy carbon electrode (GC/GNSs/MnOx) was simply prepared by casting a thin film of GNSs on the GC electrode surface, followed by performing electrodeposition of MnOx at applied constant potential. The GC/GNSs/MnOx modified electrode shows high catalytic activity toward oxidation of L ‐cysteine. Hydrodynamic amperometry determination of L ‐cysteine gave linear responses over a concentration range up to 120 µM with a detection limit of 75 nM and sensitivity of 27 nA µM?1. The GC/GNSs/MnOx electrode appears to be a highly efficient platform for the development of sensitive, stable and reproducible L ‐cysteine electrochemical sensors.  相似文献   

6.
    
Owing to their versatility and unique characteristics, graphene-based materials have been used extensively for the development of electrochemical sensors and biosensors. The key to the maximum potential of these materials is the understanding of the role their structure plays in their modification processes. Herein, we summarize some structural characteristics of graphene oxide (GO) and reduced graphene oxide (rGO) and explore different surface modification methods for electrochemical sensing applications. surveyed the most recent applications of these materials as (bio)sensors, particularly for environmental monitoring and health-related applications, such as quantification of biomarkers and metabolites and detection of cancer cells. The low detection limits, selectivity toward target molecules, and robustness of GO- and rGO-based electrodes render them critical materials for the preparation of sensors for routine analysis and monitoring.  相似文献   

7.
    
A simple and efficient procedure is described for the electrochemical determination of ledipasvir (LDP) in presence of co‐formulated drug sofosbuvir (SOF). Herein, a highly sensitive, low‐cost electrochemical protocol was utilized to fabricate a zeolite modified carbon paste electrode (ZY/CPE) through mixing of zeolite nanostructures with graphite powder. The fabricated sensor displayed high sensitivity, allowing optimal charge transfer/electrode kinetics. Different experimental and chemical factors, including electrode composition, effect of pH, scan rate and amount of ZY were evaluated carefully to obtain the highest electrochemical response. Under optimized conditions and using square wave voltammetry (SWV), the current response of the ZY/CPE electrochemical sensing platform exhibited a detection limit of 7.5×10?9 M and a large linear range from 5.0×10?8 to 1.0×10?4 M. The practical applicability of the suggested electrochemical platform was verified in the assessment of LDP in pharmaceutical formulations with excellent recoveries in the range of 99.50–98.87 %. Moreover, a biological relevance of the developed sensor was established by the analysis of LDP in human urine and plasma samples with satisfactory recoveries of 99.00 and 99.68 %, respectively. Due to the simplicity and ease of preparation of the proposed sensor, it can be used in quality control laboratories and for clinical analysis.  相似文献   

8.
    
Novel electrochemical sensors for epinephrine (EP) based on a glassy carbon electrode (GCE) modified with a redox polymer film and iron (III) oxide nanoparticles (Fe2O3NP) have been developed. Two redox polymers‐poly(brilliant cresyl blue) (PBCB) and poly(Nile blue) (PNB), and two different architectures‐polymer/Fe2O3/GCE and Fe2O3/polymer/GCE were investigated. The electrochemical oxidation of epinephrine at the modified electrodes was performed by differential pulse voltammetry (DPV), in pH 7 electrolyte, and the analytical parameters were determined. The results show enhanced performance, more sensitive responses and lower detection limits at the modified electrodes, compared to other electrochemical epinephrine sensors reported in the literature. The best voltammetric response with the lowest detection limit was obtained for the determination of epinephrine at PBCB/Fe2O3/GCE. The novel sensors are reusable, with good reproducibility and stability, and were successfully applied to the determination of epinephrine in commercial injectable adrenaline samples.  相似文献   

9.
Graphene related materials are widely expected to play a major role as materials for the construction of supercapacitors. We demonstrate here that graphene oxides prepared by various well-established methods exhibit dramatically different capacitances. We exfoliated graphite oxide sonographically to graphene oxide (GO) and we reduced GO by chemical or electrochemical means to chemically reduced graphene oxide (CRGO) and electrochemically reduced graphene oxide (ERGO); in addition, graphite oxide was thermally exfoliated leading to thermally reduced graphene oxide (TRGO). We found clear dependence of weight specific capacitance upon amount of oxygen containing groups presented on the surface of these graphenes. GO exhibits the lowest and TRGO the highest values of weight specific capacitance.  相似文献   

10.
    
Herein, two electrochemical methods based on potentiometric and impedimetric transductions were presented for albumin targeting, employing screen-printed platforms (SPEs) to make easy and cost-effective sensors with good detection merits. The SPEs incorporated ion-to-electron multi-walled carbon nanotubes (MWCNTs) transducer. Sensors were constructed using either tridodecyl methyl-ammonium chloride (TDMACl) (sensor I) or aliquate 336S (sensor II) in plasticized polymeric matrices of carboxylated poly (vinyl chloride) (PVC-COOH). Analytical performances of the sensors were evaluated using the above-mentioned electrochemical techniques. For potentiometric assay, constructed sensors responded to albumin with −81.7 ± 1.7 (r2 = 0.9986) and −146.2 ± 2.3 mV/decade (r2 = 0.9991) slopes over the linearity range 1.5 μM–1.5 mM with 0.8 and 1.0 μM detection limits for respective TDMAC- and aliquate-based sensors. Interference study showed apparent selectivity for both sensors. Impedimetric assays were performed at pH = 7.5 in 10 mM PBS buffer solution with a 0.02 M [Fe(CN)6]−3/−4 redox-active electrolyte. Sensors achieved detection limits of 4.3 × 10−8 and 1.8 × 10−7 M over the linear ranges of 5.2×10−8–1.0×10−4 M and 1.4×10−6–1.4×10−3 M, with 0.09 ± 0.004 and 0.168 ± 0.009 log Ω/decade slopes for sensors based on TDMAC and aliquate, respectively. These sensors are characterized with simple construction, high sensitivity and selectivity, fast response time, single-use, and cost-effectiveness. The methods were successfully applied to albumin assessment in different biological fluids.  相似文献   

11.
氧化石墨烯的可控还原及结构表征   总被引:1,自引:0,他引:1  
采用氧化还原法, 通过控制还原时间制备了不同还原程度的石墨烯; 用红外光谱、 紫外光谱、 拉曼光谱、 X射线衍射、 热重分析、 电导率测量等多种手段系统研究了不同还原程度石墨烯的结构与性能; 采用透射电子显微镜、 扫描电子显微镜和原子力显微镜比较了氧化石墨烯和石墨烯的形貌. 结果表明, 随着还原程度的增加, 石墨烯中含氧基团减少, 紫外吸收峰逐渐红移, D带与G带的强度比增加, 热稳定性和导电性提高. 微观结构表征说明石墨烯比氧化石墨烯片的厚度增加, 褶皱增多.  相似文献   

12.
A novel Cu-zeolite A/graphene modified glassy carbon electrode for the simultaneous electrochemical determination of dopamine (DA) and ascorbic acid (AA) has been described. The Cu-zeolite A/graphene composites were prepared using Cu2+ functionalized zeolite A and graphene oxide as the precursor, and subsequently reduced by chemical agents. The composites were characterized by X-ray diffraction, Fourier transform infrared spectra and scanning electron microscopy. Based on the Cu-zeolite A/graphene-modified electrode, the potential difference between the oxidation peaks of DA and AA was over 200 mV, which was adequate for the simultaneous electrochemical determination of DA and AA. Also the proposed Cu-zeolite/graphene-modified electrode showed higher electrocatalytic performance than zeolite/graphene electrode or graphene-modified electrode. The electrocatalytic oxidation currents of DA and AA were linearly related to the corresponding concentration in the range of 1.0 × 10−7–1.9 × 10−5 M for DA and 2.0 × 10−5–2.0 × 10−4 M for AA. Detection limits (<!-- no-mfc -->S/N<!-- /no-mfc --> = 3) were estimated to be 4.1 × 10−8 M for DA and 1.1 × 10−5 M for AA, respectively.  相似文献   

13.
    
Graphene‐based nanohybrid is considered to be the most promising nanomaterial for electrochemical sensing applications due to the defects created on the graphene oxide layers. These defects provide graphene oxide unique properties, such as excellent conductivity, large specific surface area, and electrocatalytic activity. These unique properties encourage scientists to develop novel graphene‐based nanohybrids and improve the sensing efficiency. This review, therefore, addresses this topic by comprehensively discussing the strategies to fabricate novel graphene based nanohybrids with high sensitivity. The combinations of graphene with various nanomaterials, such as metal nanoclusters, metal compound nanoparticles, carbon materials, polymers and peptides, in the direction of electrochemical sensing, were systematically analyzed. Meanwhile, the challenges in the functional design and application of graphene‐based nanohybrids were described and the reasonable solutions were proposed.  相似文献   

14.
Electrode fouling and passivation is a substantial and inevitable limitation in electrochemical biosensing, and it is a great challenge to efficiently remove the contaminant without changing the surface structure and electrochemical performance. Herein, we propose a versatile and efficient strategy based on photocatalytic cleaning to construct renewable electrochemical sensors for cell analysis. This kind of sensor was fabricated by controllable assembly of reduced graphene oxide (RGO) and TiO2 to form a sandwiching RGO@TiO2 structure, followed by deposition of Au nanoparticles (NPs) onto the RGO shell. The Au NPs‐RGO composite shell provides high electrochemical performance. Meanwhile, the encapsulated TiO2 ensures an excellent photocatalytic cleaning property. Application of this renewable microsensor for detection of nitric oxide (NO) release from cells demonstrates the great potential of this strategy in electrode regeneration and biosensing.  相似文献   

15.
通过改进的Hummers法合成氧化石墨烯(GO), 随后采用水热法制备石墨烯负载锰氧化物(MnOx/GR)催化剂. 考察了催化剂的低温NH3选择性催化还原(NH3-SCR)去除NOx的性能, 并通过傅里叶变换红外(FTIR)光谱, 拉曼(Raman)光谱, X射线衍射(XRD), 透射电镜(TEM), N2吸附-脱附, X射线光电子能谱(XPS)及H2程序升温还原(H2-TPR)等多种表征手段对催化剂的结构及NH3-SCR性能进行分析. 结果显示, 不同MnOx负载量的MnOx/GR催化剂均展现了较好的低温SCR催化活性, 且在负载量为20%(w)时活性最优. 表征分析结果表明, 制备的GO表面含有丰富的含氧基团, 锰可以通过与含氧基团结合而负载到GO上; MnOx/GR催化剂中MnOx以纳米颗粒分散于石墨烯载体表面, 且以多种氧化物(MnO、Mn3O4和MnO2)共同存在; 负载量为20%(w)的催化剂中高价锰和表面吸附氧含量增加, 低温区氧化还原能力增强及活性位点数量增加是其SCR活性提高的原因.  相似文献   

16.
    
《Electroanalysis》2017,29(5):1350-1358
In our study, graphene oxide (GO) modified graphite electrodes were used for sensitive and selective impedimetric detection of miRNA. After chemical activation of pencil graphite electrode (PGE) surface using covalent agents (CA), GO modification was performed at the surface of chemically activated PGE. Then, CA‐GO‐PGEs were applied for impedimetric miRNA detection. The microscopic and electrochemical characterization of CA‐GO‐PGEs was performed by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The optimization of experimental conditions; such as GO concentration, DNA probe concentration and miRNA target concentration was performed by using EIS technique. After the hybridization occurred between miRNA‐34a RNA target and its complementary DNA probe, the hybrid was immobilized onto the surface of CA‐GO‐PGEs. Then, the impedimetric detection of miRNA‐DNA hybridization was performed by EIS. The selectivity of our assay was also tested under the optimum experimental conditions.  相似文献   

17.
应用球磨法于LiFePO4掺杂多壁碳纳米管,制成LiFePO4/MWCNTs复合电极,然后以其组装成锂离子电池.研究不同比例掺杂多壁碳纳米管对复合材料电极电化学性能的影响.XRD、SEM表征及电化学性能测试表明,多壁碳纳米管含量为10%(bymass)的LiFePO4/MWCNTs电极比其它比例的复合电极具有更优良的充放电性能,而且极化小、稳定性强、充放电平台更平稳,导电率更高.在常温0.1C下充放电,首次充、放电比容量分别为139和128.5mAh.g-1,库仑效率达92.4%,循环40次后,电极比容量损失率仅为5.3%.  相似文献   

18.
The electrochemical properties of single crystals of cerium fluoride alloyed with bivalent cations Sr2+, Ca2+, Ba2+, Sr2+ + Ca2+, Sr2+ + Ba2+, Ba2+ + Ca2+ and also with La3+ and La3+ + Ba2+ cations are studied using the dynamic voltammetry and impedance spectroscopy. The conductivity of symmetrical cells with Ag electrodes is determined using the method of impedance spectroscopy in the frequency range from 450 to 5 kHz at the temperatures from 20 to 100°C: for CeF3: Sr2+ (0.5 mol %) + Ba2+ (0.5 mol %), σ = σ0 exp[(?0.284 ± 0.005/kT]; for CeF3:Ca2+ (0.5 mol %) + Sr2+ (0.5 mol %), σ = σ0 exp[(?0.292 ± 0.017/kT]. The steady-state and dynamic voltammogams of symmetrical electrochemical cells with nonpolarizable reference electrodes and CeF3 single crystals alloyed with Sr2+, Ca2+, and Ba2+ bivalent cations exhibited ohmic polarization. For cells with CeF3 containing La3+ as an admixture, a hysteresis was observed, which could not be eliminated by chemical and electrochemical treatment of crystals. In the dynamic voltammetric curves of asymmetric cells with nonpolarizable and silver electrode and CeF3 crystals alloyed with Sr2+, Ca2+, and Ba2+, a range of ideal polarizability (from 0 to ~?2.7 V), and also cerium redox processes and silver fluorination-boundary regeneration were observed. In the dynamic voltammetric curves of asymmetric cells with CeF3 containing La3+ admixture, no range of ideal polarizability was observed; however, the reactions of silver fluorination and reduction of solid-electrolyte cerium were well pronounced at the corresponding potentials.  相似文献   

19.
利用电化学还原方法制备纳米金/石墨烯修饰玻碳电极,研究了多巴胺(DA)在该修饰电极上的电化学行为,建立了电化学测定多巴胺的新方法.结果表明,在磷酸盐缓冲溶液中,此修饰电极对多巴胺的电化学响应具有很好的催化作用.利用差示脉冲伏安技术对多巴胺的电化学氧化进行定量分析,多巴胺的氧化峰电流与其浓度在1.0×10-7~ 1.0×10 -5mol/L范围内呈良好的线性关系,检测限低至4.0×10 -8mol/L.该修饰电极适于多巴胺的分析检测.  相似文献   

20.
Li J  Chen J  Zhang XL  Lu CH  Yang HH 《Talanta》2010,83(2):553-558
This paper has presented a novel strategy to carry out direct and sensitive determination of antitumor herbal drug aloe-emodin in complex matrices based on the graphene-Nafion modified glassy carbon (GN/GC) electrode. This proposed modified electrode showed good electrochemical response towards aloe-emodin (AE). Compared with the multiwall carbon nanotubes (MWCNTs) modified electrode, the GN/GC electrode has the advantages of higher sensitivity and lower cost. Under the optimized conditions, the calibration curve for AE concentration was linear in the range from 5 nmol/L to 1 μmol/L with the detection limit of 2 nmol/L. In addition, the practical analytical performance of the GN/GC electrode was examined by evaluating the selective detection of AE in natural aloe extracts and human urine samples with satisfied recovery. Therefore, the GN/GC electrode may hold great promise for fast, simple and sensitive detection and biomedical analysis of AE in complex matrices.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号