碳纳米管负载的Pd-Ag-Sn催化剂对甲酸的电氧化

采用硼氢化钠还原的方法合成了碳纳米管负载的钯基纳米催化剂（Pd/CNT,Pd₇Ag₃/CNT,Pd₇Sn₂/CNT,Pd₇Ag₁Sn₂/CNT,Pd₇Ag₂Sn₂/CNT和Pd₇Ag₃Sn₂/CNT）。通过XRD,TEM和XPS对其进行了表征,结果表明,相比Pd/CNT和Pd-Ag（或Pd-Sn）催化剂的纳米颗粒,Pd-Ag-Sn催化剂展现出了更小的平均颗粒尺寸（2.3 nm）。此外,还通过循环伏安（CV）和计时电流法（CA）测试了这些催化剂对甲酸氧化的电活性,在酸碱介质中,Pd-Ag-Sn/CNT对甲酸氧化都表现出了更高的电流密度。其中,Pd₇Ag₂Sn₂/CNT催化剂在酸碱介质中的电流密度分别是108.8和211.3 mA·cm^-2,相应的Pd质量电流密度高达1 364和2 640 mA·mg^-1,远远高于商业Pd/C,表明Pd-Ag-Sn/CNT催化剂对甲酸氧化表现出了极好的电催化活性。     

Electronic Modulation of Palladium in Metal Phosphide Nanoparticles for Chemoselective Reduction of Halogenated Nitrobenzenes

Tuning the electronic property of a transition metal plays an important role in the selective catalysis. Herein, the control synthesis of (Pd_xNi_y)‐P nanoparticles is reported. The binding energy of Pd3d_5/2 as a function of x/y ratio is well tunable from 335.3 to 335.9 eV. The composition‐induced electronic modulation was correlated with the selective catalysis of (Pd_xNi_y)‐P in the reduction of halogenated nitrobenzenes. The electro‐deficiency of Pd helped to improve the selectivity. The amorphous (Pd₃₈Ni₂₆)P₃₆/C performed an exceptional selectivity in comparison with other related (Pd‐Ni)‐P/C, Pd₃₈Ni₂₆/C, and Pd/C. Various halogenated nitrobenzenes (chlorides, bromides, and iodide) were tolerant and the corresponding halogenated anilines were obtained in high yields. This work provides some clues for the rational design of bimetallic phosphides with covalent interactions to boost the catalysis.     

Pd‐Cu alloy nanoparticle supported on amine‐terminated ionic liquid functional 3D graphene and its application on Suzuki cross‐coupling reaction

Well distributed Pd‐Cu bimetallic alloy nanoparticles supported on amine‐terminated ionic liquid functional three‐dimensional graphene (3D IL‐rGO/Pd‐Cu) as an efficient catalyst for Suzuki cross‐coupling reaction has been prepared via a facile synthetic method. The introduction of IL‐NH₂ cations on the surface of graphene sheets can effectively avoid the re‐deposition of graphene sheets, allowing the catalyst to be reused up to 10 cycles. The addition of Cu not only saves cost but also ensures high catalytic efficiency. It is worthy to note that the catalyst 3D IL‐rGO/Pd_2.5Cu_2.5 can efficiently catalyze the Suzuki cross‐coupling reaction with the yield up to 100% in 0.25 h, almost one‐fold higher than that by the pristine IL‐rGO/Pd_2.5 catalyst (52%). The Powder X‐Ray Diffraction (XRD), combining energy dispersive X‐ray spectroscopy (EDS) mapping results confirm the existence and distribution of Pd and Cu in the bimetallic nanoparticles. The transmission electron microscopy (TEM) reveals the nanoparticle size with an average diameter of 3.0 ± 0.5 nm. X‐ray photoelectron spectroscopy (XPS) analysis proved the presence of electron transfer from Cu to Pd upon alloying. Such alloying‐induced electronic modification of Pd‐Cu alloy and 3D ionic liquid functional graphene with large specific surface area both accounted for the catalytic enhancement.     

炭载Pd-Ni合金纳米粒子对甲酸的电催化氧化

通过液相还原法制备了具有不同原子比例的Pd-Ni/C催化剂,并且使用X射线衍射（XRD）、透射电子显微镜(TEM)和X射线光电子能谱(XPS) 等表征手段对制备的催化剂进行了表征,总结了Ni的掺杂对Pd-Ni合金纳米粒子的尺寸及晶体结构的影响。电化学测试结果表明：适量的Ni的掺杂不但能够增强催化剂对甲酸催化氧化的活性,而且还能够提高催化剂的稳定性。因此,Pd-Ni/C催化剂是一类具有潜在应用前景的直接甲酸燃料电池阳极催化剂     

Structural and Electronic Effects of Carbon‐Supported PtxPd1−x Nanoparticles on the Electrocatalytic Activity of the Oxygen‐Reduction Reaction and on Methanol Tolerance

We report a systematic investigation on the structural and electronic effects of carbon‐supported Pt_xPd_1?x bimetallic nanoparticles on the oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) in acid electrolyte. Pt_xPd_1?x/C nanocatalysts with various Pt/Pd atomic ratios (x=0.25, 0.5, and 0.75) were synthesized by using a borohydride‐reduction method. Rotating‐disk electrode measurements revealed that the Pt₃Pd₁/C nanocatalyst has a synergistic effect on the ORR, showing 50 % enhancement, and an antagonistic effect on the MOR, showing 90 % reduction, relative to JM 20 Pt/C on a mass basis. The extent of alloying and Pt d‐band vacancies of the Pt_xPd_1?x/C nanocatalysts were explored by extended X‐ray absorption fine‐structure spectroscopy (EXAFS) and X‐ray absorption near‐edge structure spectroscopy (XANES). The structure–activity relationship indicates that ORR activity and methanol tolerance of the nanocatalysts strongly depend on their extent of alloying and d‐band vacancies. The optimal composition for enhanced ORR activity is Pt₃Pd₁/C, with high extent of alloying and low Pt d‐band vacancies, owing to favorable O? O scission and inhibited formation of oxygenated intermediates. MOR activity also shows structure dependence. For example, Pt₁Pd₃/C with Pt_rich?corePd_rich?shell structure possesses lower MOR activity than the Pt₃Pd₁/C nanocatalyst with random alloy structure. Herein, extent of alloying and d‐band vacancies reveal new insights into the synergistic and antagonistic effects of the Pt_xPd_1?x/C nanocatalysts on surface reactivity.     

Self‐Assembly Film of Zeolite Y Nanocrystals Loading Palladium on an Au Electrode for Electrochemical Applications

Nano‐scale zeolite Y crystals were synthesized, and palladium nanoparticles were prepared in the supercage of the zeolite by “ship‐in‐a‐bottle” approach. A novel method to fabricate zeolite‐modified electrode (ZME) loading Pd nanoparticles was developed, in which the zeolite Y loading Pd²⁺ ions was self‐assembled on (3‐mercaptopropyl) trimethoxysilane‐attached Au surface to form the stable and density packed multilayers (SAM‐ZME). The structures of zeolite Y and the SAM‐ZME were investigated by using TEM, XRD and SEM techniques. Pd²⁺ ions in the SAM‐ZME were converted into Pd nanoparticles (Pd_n⁰) by two steps consisting of the electrochemical reduction as well as the succeeding admission and release of CO. The redox couple [Fe(CN)₆]^3?/4? was used to probe the electron‐transfer barrier properties during self‐assembling process. Moreover, the special properties of the SAM‐ZME loading Pd_n⁰ were studied by using cyclic voltammetry and CO‐probe in situ FTIR spectroscopy. The results illustrated that Pd_n⁰ in the SAM‐ZME exhibits higher electrocatalytic activity for oxidation of adsorbed CO than that of ZME prepared in our previous study by zeolite coating method. The present study is of importance in design and preparation of SAM‐ZME, which poccesseses excellent properties for the immobilization of electrocatalysts or biomolecules.     

相转移法制备PdMo催化剂及其氧还原活性

以四丁基氢氧化铵作为相转移剂,以硼氢化钠为还原剂,利用相转移法在二氯甲烷中制备了一系列不同比例的Pd_xMo/C(Pd/Mo的原子比x=1、2、3、4、5)催化剂。透射电镜(TEM)图像显示,Pd_x Mo/C是呈2～4 nm的圆形颗粒,尺寸均匀、分散性良好。X射线衍射(XRD)结果表明,加入第二组元Mo后,Pd的晶格发生扩张,调节了 Pd的几何结构。此外,X射线光电子能谱(XPS)结果表明,相对于Pd/C,Pd_4Mo/C的Pd3d_(5/)2结合能负移了 0.50 eV,说明电负性较大的Pd从Mo吸电子,电子结构发生改变。氧还原反应(ORR)结果表明,不同比例的Pd_xMo/C催化剂活性均优于Pd/C,其中当x=4时,ORR活性最佳,其起始电位和半波电位分别为0.876和0.813 V,高于商业Pt/C的0.870和0.810 V。此外,在经过3 h的运行之后电流密度仍保留82.9%,与商业Pt/C相比具有明显的优势。     

Supported Pd–Cu Bimetallic Nanoparticles That Have High Activity for the Electrochemical Oxidation of Methanol

Monodisperse bimetallic Pd–Cu nanoparticles with controllable size and composition were synthesized by a one‐step multiphase ethylene glycol (EG) method. Adjusting the stoichiometric ratio of the Pd and Cu precursors afforded nanoparticles with different compositions, such as Pd₈₅–Cu₁₅, Pd₅₆–Cu₄₄, and Pd₃₉–Cu₆₁. The nanoparticles were separated from the solution mixture by extraction with non‐polar solvents, such as n‐hexane. Monodisperse bimetallic Pd–Cu nanoparticles with narrow size‐distribution were obtained without the need for a size‐selection process. Capping ligands that were bound to the surface of the particles were removed through heat treatment when the as‐prepared nanoparticles were loaded onto a Vulcan XC‐72 carbon support. Supported bimetallic Pd–Cu nanoparticles showed enhanced electrocatalytic activity towards methanol oxidation compared with supported Pd nanoparticles that were fabricated according to the same EG method. For a bimetallic Pd–Cu catalyst that contained 15 % Cu, the activity was even comparable to the state‐of‐the‐art commercially available Pt/C catalysts. A STEM‐HAADF study indicated that the formation of random solid‐solution alloy structures in the bimetallic Pd₈₅–Cu₁₅/C catalysts played a key role in improving the electrochemical activity.     

An Effective Pd–Ni2P/C Anode Catalyst for Direct Formic Acid Fuel Cells

The direct formic acid fuel cell is an emerging energy conversion device for which palladium is considered as the state‐of‐the‐art anode catalyst. In this communication, we show that the activity and stability of palladium for formic acid oxidation can be significantly enhanced using nickel phosphide (Ni₂P) nanoparticles as a cocatalyst. X‐ray photoelectron spectroscopy (XPS) reveals a strong electronic interaction between Ni₂P and Pd. A direct formic acid fuel cell incorporating the best Pd–Ni₂P anode catalyst exhibits a power density of 550 mW cm^?2, which is 3.5 times of that of an analogous device using a commercial Pd anode catalyst.     

NH_4~+对甲酸在炭载Pd催化剂上氧化性能的影响

为了解HClO4、NH4ClO4和NaClO4电解液对炭载Pd(Pd/C)催化剂电极对甲酸氧化的电催化性能的影响,在用X射线衍射(XRD)谱、能量色散谱(EDS)和透射电子显微镜(TEM)对Pd/C催化剂进行表征的基础上,采用电化学方法测量了Pd/C催化剂在不同电解液中对甲酸氧化的电催化性能.发现在不同电解液中,Pd/C催化剂对甲酸氧化的电催化活性和稳定性按NH4ClO4NaClO4HClO4的次序降低.由于甲酸的存在,不同电解液的pH相差较小,因此,电解液的pH影响较小,而阳离子的影响较大.在NaClO4电解液中的性能优于在HClO4电解液中的性能是pH的影响.在NH4ClO4电解液中的性能优于在NaClO4电解液中是由于NH4+能降低CO在Pd/C催化剂电极上的吸附强度和吸附量,这一发现对提高直接甲酸燃料电池(DFAFC)的性能很有意义.     

In situ green synthesis of Cu‐Ni bimetallic nanoparticles supported on reduced graphene oxide as an effective and recyclable catalyst for the synthesis of N‐benzyl‐N‐aryl‐5‐amino‐1H‐tetrazoles

In the present work, for the first time we have designed a novel approach for the synthesis of N‐benzyl‐N‐aryl‐5‐amino‐1H‐tetrazoles using reduced graphene oxide (rGO) decorated with Cu‐Ni bimetallic nanoparticles (NPs). In situ synthesis of Cu/Ni/rGO nanocomposite was performed by a cost efficient, surfactant‐free and environmentally benign method using Crataegus azarolus var. aronia L. leaf extract as a stabilizing and reducing agent. Phytochemicals present in the extract can be used to reduce Cu²⁺ and Ni²⁺ ions and GO to Cu NPs, Ni NPs and rGO, respectively. Analyses by means of FT‐IR, UV–Vis, EDS, TEM, FESEM, XRD and elemental mapping confirmed the Cu/Ni/rGO formation and also FT‐IR, NMR, and mass spectroscopy as well as elemental analysis were used to characterize the tetrazoles. The Cu/Ni/rGO nanocomposite showed the superior catalytic activity for the synthesis of N‐benzyl‐N‐aryl‐5‐amino‐1H‐tetrazoles within a short reaction time and high yields. Furthermore, this protocol eliminates the need to handle HN₃.     

Influence of Metallic Modification on Ethylbenzene Dealkylation over ZSM‐5 Zeolites

A series of metal‐modified HZSM‐5 catalysts were prepared by impregnation and were used for ethylbenzene dealkylation of the mixed C8 aromatics (ethylbenzene, m‐xylene and o‐xylene). The effects of different supported metals (Pt, Pd, Ni, Mo) on catalytic performance, including reaction conditions, were investigated. The physicochemical properties of catalysts were characterized by means of XRD, BET, TEM and NH₃‐TPD. Experimental results showed that metallic modification obviously increased the ethylbenzene conversion and reduced the coke deposition, greatly improving the catalyst stability. The distinction of ethylbenzene conversion depended on the interaction between hydrogenation reactivity and acidic cracking of bifunctional metal‐modified zeolites. Compared with Pt and Ni, Pd and Mo were easier to disperse into HZSM‐5 micropores during loading metals. The acidic density of different metal‐modified HZSM‐5 declined in the following order: HZSM‐5>Pt/HZSM‐5>Pd/HZSM‐5>Ni/HZSM‐5>Mo/HZSM‐5. The activity of ethylene hydrogenation decreased with Pt/HZSM‐5>Pd/HZSM‐5>Ni/HZSM‐5>Mo/HZSM‐5. In comparison, Pd/HZSM‐5 showed the best catalytic performance with both high activity and high selectivity, with less cracking loss of m‐xylene and o‐xylene. Moreover, the following reaction conditions were found to be preferable for ethylbenzene dealkylation over Pd/HZSM‐5: 340°C, 1.5 MPa H₂, WHSV 4 h^?1, H₂/C8 4 mol/mol.     

A composite made from palladium nanoparticles and carbon nanofibers for superior electrocatalytic oxidation of formic acid

We report on a novel type of nanocomposite for use in the electrooxidation of formic acid in fuel cells. The material is composed of palladium nanoparticles (Pd-NPs) and carbon nanofibers (CNFs) and was prepared by electrospinning of the precursors Pd(acac)₂ and polyacrylonitrile, respectively, followed by thermal treatment to generate in-situ Pd-NPs that are well dispersed within the CNF framework. The nanocomposite was characterized by TEM, high-resolution TEM, SEM, XRD, Raman spectroscopy, and XPS. The size of the Pd-NPs ranges from 12 to 82 nm, depending on the temperature for carbonization (700–1,000 °C). The length and width of the CNF is in the order of tens of micrometers and 300 to 500 nm, respectively. TEM and XPS studies indicate that the Pd-NPs are firmly embedded in the CNF, resulting in a good electrochemical stability of the composite. The electrocatalytic properties of the composite with respect to the oxidation of formic acid were studied by cyclic voltammetry and chronoamperometry. They showed a distinctly improved electrocatalytic activity and stability compared to a commercial Pd-on-carbon catalyst. The Pd/CNF composite carbonized at 900 °C was found to display the best performance.

Preparation of Pd/C catalyst for formic acid oxidation using a novel colloid method

A novel colloid method using (WO₃)_n·xH₂O as colloidal source was developed to prepare Pd/C catalyst for formic acid oxidation. Transmission electron microscopy image shows that the Pd/C nanoparticles have an average size of 3.3 nm and a narrow size distribution. Electrochemical measurements indicate that the Pd/C catalyst exhibits significantly high electrochemical active surface area and high catalytic activity with good stability for formic acid oxidation compared with that prepared by common method. The colloid method is very simple and has great potentials for mass-producing Pd/C and others noble metal catalysts.     

Coated/Sandwiched rGO/CoSx Composites Derived from Metal–Organic Frameworks/GO as Advanced Anode Materials for Lithium‐Ion Batteries

Rational composite materials made from transition metal sulfides and reduced graphene oxide (rGO) are highly desirable for designing high‐performance lithium‐ion batteries (LIBs). Here, rGO‐coated or sandwiched CoS_x composites are fabricated through facile thermal sulfurization of metal–organic framework/GO precursors. By scrupulously changing the proportion of Co²⁺ and organic ligands and the solvent of the reaction system, we can tune the forms of GO as either a coating or a supporting layer. Upon testing as anode materials for LIBs, the as‐prepared CoS_x‐rGO‐CoS_x and rGO@CoS_x composites demonstrate brilliant electrochemical performances such as high initial specific capacities of 1248 and 1320 mA h g^?1, respectively, at a current density of 100 mA g^?1, and stable cycling abilities of 670 and 613 mA h g^?1, respectively, after 100 charge/discharge cycles, as well as superior rate capabilities. The excellent electrical conductivity and porous structure of the CoS_x/rGO composites can promote Li⁺ transfer and mitigate internal stress during the charge/discharge process, thus significantly improving the electrochemical performance of electrode materials.     

One Step Preparation of Reduced Graphene Oxide/Pd–Fe3O4@Polypyrrole Composites and Their Application in Catalysis

The simple preparation of catalysts with superior catalytic activity and good reusability is highly desirable. Herein, we report a novel strategy to construct reduced graphene oxide (rGO)/Pd–Fe₃O₄@polypyrrole (PPy) catalysts with Pd and Fe₃O₄ nanoparticles anchored on a rGO nanosheet surface and wrapped in a PPy shell. The synthesis and assembly of both the Pd and Fe₃O₄ nanoparticles, the preparation of the PPy layer, and the reduction of graphene oxide nanosheets were finished in one step. In the system, the PPy layer not only prevented aggregation of Pd and Fe₃O₄ nanoparticles, but also generated a synergistic effect with precursor Pd²⁺ ions, which led to a high dispersity of as‐prepared Pd nanoparticles. Although the procedure was simplified to one step, the catalytic activity and reusability were not sacrificed. In the reduction of 4‐nitrophenol, their catalytic performance was better than that in recent reports. Moreover, the catalysts showed good reusability owing to their magnetic properties.     

Oxoanionic Noble Metal Compounds from Fuming Nitric Acid: The Palladium Examples Pd(NO3)2 and Pd(CH3SO3)2

The oxidation of elemental palladium at 100 °C in a mixture of fuming nitric acid and a pyridine‐SO₃ complex leads to the anhydrous nitrate Pd(NO₃)₂ (monoclinic, P2₁/n, Z=2, a=469.12(3) pm, b=593.89(3) pm, c=805.72(4) pm, β=105.989(3)°, V=215.79(2) ų). The Pd²⁺ ions are in square‐planar coordination with four monodentate nitrate groups which are connected to further palladium atoms, leading to a layer structure. The reaction of elemental palladium with a mixture of fuming nitric acid and methanesulfonic acid at 120 °C leads to single crystals of Pd(CH₃SO₃)₂ (monoclinic, P2₁/n, Z=2, a=480.44(1) pm, b=1085.53(3) pm, c=739.78(2) pm, β=102.785(1)°, V=376.254(17) ų). Also in this structure the Pd²⁺ ions are in square‐planar coordination with four monodentate anions; however, the connection to adjacent palladium atoms leads to a chain‐type structure. The thermal decomposition of the compounds has been investigated by means of DSC/TG measurements. Furthermore, IR and Raman spectra have been recorded, and an assignment of the observed vibrational frequencies has been carried out based on theoretical investigations.     

A trinuclear palladium(II) complex containing N,S‐coordinating 2‐(benzylsulfanyl)anilinide and 1,3‐benzothiazole‐2‐thiolate ligands with a central square‐planar PdN4 motif

The reaction of dichlorido(cod)palladium(II) (cod = 1,5‐cyclooctadiene) with 2‐(benzylsulfanyl)aniline followed by heating in N,N‐dimethylformamide (DMF) produces the linear trinuclear Pd₃ complex bis(μ₂‐1,3‐benzothiazole‐2‐thiolato)bis[μ₂‐2‐(benzylsulfanyl)anilinido]dichloridotripalladium(II) N,N‐dimethylformamide disolvate, [Pd₃(C₇H₄NS₂)₂(C₁₃H₁₂NS)₂Cl₂]·2C₃H₇NO. The molecule has symmetry and a Pd...Pd separation of 3.2012 (4) Å. The outer Pd^II atoms have a square‐planar geometry formed by an N,S‐chelating 2‐(benzylsulfanyl)anilinide ligand, a chloride ligand and the thiolate S atom of a bridging 1,3‐benzothiazole‐2‐thiolate ligand, while the central Pd^II core shows an all N‐coordinated square‐planar geometry. The geometry is perfectly planar within the PdN₄ core and the N—Pd—N bond angles differ significantly [84.72 (15)° for the N atoms of ligands coordinated to the same outer Pd atom and 95.28 (15)° for the N atoms of ligands coordinated to different outer Pd atoms]. This trinuclear Pd₃ complex is the first example of one in which 1,3‐benzothiazole‐2‐thiolate ligands are only N‐coordinated to one Pd centre. The 1,3‐benzothiazole‐2‐thiolate ligands were formed in situ from 2‐(benzylsulfanyl)aniline.     

Enhanced electro-oxidation of formic acid by a PdPt bimetallic catalyst on a CeO2-modified carbon support

PdPt bimetallic catalysts that employ CeO2-modified carbon black as a support have been prepared using an organic colloidal method.PdPt/CeO2-C shows excellent performance toward the anodic oxidation of formic acid.The effects of varying both Pd to Pt ratio and CeO2 content have been investigated.The optimal Pd to Pt atomic ratio is 15,indicating that addition of small amounts of Pt can significantly enhance the activity of the catalyst.When the CeO2 content in the catalyst reaches as high as ～15 wt.%,the catalyst shows the maximum activity.Adding CeO2 not only enhances the catalytic activity of the material,but may also change the mechanism of its catalysis of the anodic oxidation of formic acid.Pd15Pt1/15CeO2-C exhibited 60% higher activity than Pd/C,and had a negative shift in onset potential of more than 0.1 V.Based on characterization by X-ray diffraction,X-ray photoelectron spectroscopy,thermogravimetric analysis and transmission electron microscopy,the interactions between the components are revealed and discussed in detail.     

Fabrication of Non‐enzymatic Electrochemical Glucose Sensor Based on Pd−Mn Alloy Nanoparticles Supported on Reduced Graphene Oxide

Mixed metals alloy nanoparticles supported on carbon nanomaterial are the most attractive candidates for the fabrication of non‐enzymatic electrochemical sensor with enhanced electrochemical performance. In this study, palladium‐manganese alloy nanoparticles supported on reduced graphene oxide (Pd?Mn/rGO) are prepared by a simple reduction protocol. Further, a novel enzyme‐free glucose sensing platform is established based on Pd?Mn/rGO. The successful fabrication of Pd?Mn alloy nanoparticles and their attachment at rGO are thoroughly characterized by various microscopic and spectroscopic techniques such as XRD, Raman, TEM and XPS. The electrochemical activity and sensing features of designed material towards glucose detection are explored by amperometric measurments in 0.1 M NaOH at the working voltage of ?0.1 V. Thanks to the newly designed Pd?Mn/rGO nanohybrid for their superior electrorochemical activity towards glucose comprising the admirable sensing features in terms of targeted selectivity, senstivity, two linear parts and good stability. The enhanced electrochemical efficacy of Pd?Mn/rGO electrocatalyst may be credited to the abundant elecrocatalytic active sites formed during the Pd?Mn alloying and the electron transport ability of rGO that augment the electron shuttling phenomenon between the electrode material and targeted analyte.