A Biofuel Cell Based on Biocatalytic Reactions of Glucose on Both Anode and Cathode Electrodes

Biofuel cells based on electrocatalytic oxidation of NADH and reduction of H₂O₂ have been prepared using carbon fiber electrodes functionalized with graphene nano‐flakes. The electrochemical oxidation of NADH was catalyzed by Meldola's blue (MB), while the reduction of H₂O₂ was catalyzed by hemin, both catalysts were adsorbed on the graphene flakes due to their π‐π staking. In the next set of experiments, the MB‐ and hemin‐electrodes were additionally modified with glucose dehydrogenase (GDH) and glucose oxidase (GOx), respectively. The enzyme catalyzed reactions in the presence of glucose, NAD⁺ and O₂ resulted in the production of NADH and H₂O₂ in situ. The produced NADH and H₂O₂ were oxidized and reduced, respectively, at the bioelectrocatalytic electrodes, thus producing voltage and current generated by the biofuel cell. The enzyme‐based biofuel cells operated in a human serum solution modelling an implantable device powered from the natural biofluid. Finally, two enzyme‐based biofuel cell connected in series and operating in the serum solution produced electrical power sufficient for activation of an electronic watch used as an example device.     

Flow Injection Analysis of Lactate and Lactate Dehydrogenase Using an Enzyme Membrane in Conjunction with a Modified Electrode

Abstract

A modified electrode for H₂O₂ oxidation, consisting of Pd/Au sputtered on carbon was covered with a lactate oxidase membrane and used in a FIA manifold for selective determination of lactate. The linear range was 0.01-3 mM lactate and up to 200 samples per hour were measured with a relative standard deviation of 1%. Interferences from ascorbic acid and NADH were small because of the low potential of the modified electrode. The lactate oxidase membrane electrode was also used for measurement of lactate dehydrogenase activity using direct injection of the sample into a carrier stream containing pyruvate and NAD⁺.     

Amperometric Biosensor for Lactate Based on Meldola's Blue Adsorbed on Silica Gel Modified with Niobium Oxide

A reagentless amperometric biosensor sensitive to lactate was developed. This sensor comprises a carbon paste electrode modified with lactate dehydrogenase (LDH), nicotinamide adenine dinucleotide (NAD⁺) cofactor and Meldola's blue (MB) adsorbed on silica gel coated with niobium oxide. The amperometric response was based on the electrocatalytic properties of MB to oxidize NADH, which was generated in the enzymatic reaction of lactate with NAD⁺ under catalysis of LDH. The dependence on the biosensor response was investigated in terms of pH, supporting electrolyte, ionic strength, LDH and NAD⁺ amounts and applied potential. The biosensor showed an excellent operational stability (95% of the activity was maintained after 250 determinations) and storage stability (allowing measurements for over than 2.5 months, when stored in a refrigerator). The proposed biosensor also presented good sensitivity allowing lactate quantification at levels down to 6.5×10^?6 mol L^?1. Moreover, the biosensor showed a wide linear response range (from 0.1 to 14 mmol L^?1 for lactate). These favorable characteristics allowed its application for direct measurements of lactate in biological samples such as blood. The precision of the data obtained by the proposed biosensor show reliable results for real complex matrices.     

Preparation of an Electrode Modified with an Electropolymerized Film as a Mediator of NADH Oxidation and Its Application in an Ethanol/O2 Biofuel Cell

This paper reports a novel mediator for the oxidation of β‐nicotinamide adenine dinucleotide (NAD⁺/NADH), an electropolymeric film (pAPRu) of [Ru(NH₂‐phen)₃]²⁺. A pAPRu‐modified electrode was prepared via electropolymerization and exhibited catalytic activity toward the electrochemical oxidation of NADH due to the imine moieties of pAPRu. The electrochemical oxidation of ethanol was observed using an alcohol dehydrogenase (ADH)‐immobilized electrode. A compartmentless ethanol/O₂ biofuel cell composed of an ADH anode and a bilirubin oxidase cathode was constructed. The maximum current density and the maximum power density of the biofuel cell were 190 µA cm^?2 and 31 µW cm^?2 (at 0.29 V), respectively.     

Control release of lactate dehydrogenase encapsulated in poly (vinyl alcohol) nanofibers via electrospinning

Sustained release of lactate dehydrogenase (LDH, EC 1.1.1.27) from electrospun poly (vinyl alcohol) (PVA) nanofibers was successfully achieved using the coaxial electrospinning technique. The presence of the encapsulated enzyme in the nanofibers was confirmed by infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was used to evaluate the morphology and diameter of the nanofibers. The conversion of lactate to pyruvate by LDH coupling with the reduction of the cofactor nicotinamide adenine dinucleotide (NAD⁺) to dihydronicotinamide adenine dinucleotide (NADH) produces an increment in the ultraviolet absorption (UV) at 340 nm. This change in the UV absorbance was used to follow the release kinetic of LDH from the PVA nanofibers and also as a measure to evaluate the residual enzymatic catalytic function. Most of the encapsulated LDH enzyme was released in a sustained manner from the PVA nanofibers within a period of 1 month.     

A dual-amplification aptasensor for highly sensitive detection of thrombin based on the functionalized graphene-Pd nanoparticles composites and the hemin/G-quadruplex

In this work, an advanced sandwich-type electrochemical aptasensor for thrombin was proposed by integrating hemin/G-quadruplex with functionalized graphene-Pd nanoparticles composites (PdNPs-RGs). The hemin/G-quadruplex formed by intercalating hemin into thrombin binding aptamer (TBA), firstly acted as a NADH oxidase, assisting the oxidation of NADH to NAD⁺ accompanying with the generation of H₂O₂ in the presence of dissolved O₂. Subsequently, the hemin/G-quadruplex acted as HRP-mimicking DNAzyme that rapidly bioelectrocatalyze the reduction of the produced H₂O₂. At the same time, the Pd nanoparticles supported on p-iodoaniline functionalized graphene were also adopted to catalyze the reduction of H₂O₂. Thus, with the dual catalysis, a dramatically amplified electrochemical signal could be obtained. Besides, the avidin–biotin system for binding aptamer sequences on electrodes not only improved the sensitivity of thrombin analysis but also obtained an acceptable repeatability of the aptasensor. With several factors mentioned above, a wide linear ranged from 0.1 pM to 50 nM was acquired with a relatively low detection limit of 0.03 pM (defined as S/N = 3). These excellent performances provided our approach a promising way for ultrasensitive assay in electrochemical aptasensors.     

An amperometric lactate sensor based on a NAD+-analog and lactate dehydrogenase coimmobilized on reticulated vitreous carbon

A NAD⁺-analog was coimmobilized with lactate dehydrogenase (LDH) on reticulated vitreous carbon (RVC) to give an amperometric lactate biosensor. Both LDH and the NAD⁺ -analog were bound covalently with carbodiimide to the surface of the porous RVC-material. The electrode was operated in a FIA-arrangement in the presence or absence of a soluble mediator. Meldola Blue. The stability was poor when the electrode was operated at +400 mV (vs. Ag/AgCl) in the absence of mediator but improved most significantly in the presence of 5 μM mediator, so that 65% of the original activity remained after 16 days. The amperometric currents were smaller with regeneration by mediator at −100 mV than with direct electrochemical oxidation at +400 mV, indicating that the additional steps slow down the reaction rate. Linear calibration plots were obtained from the detection limit, 1 μM, to 500 μM lactate with 5 μM mediator, reoxidized at −100 mV. The sample throughput was about 60 h⁻¹.     

A biofuel cell based on pyrroloquinoline quinone and microperoxidase-11 monolayer-functionalized electrodes

A pyrroloquinoline quinone (PQQ) monolayer-functionalized-Au-electrode and a microperoxidase-11 (MP-11)-modified Au-electrode are used as catalytic anode and cathode in a biofuel cell element, respectively. The cathodic oxidizer is H₂O₂ whereas the anodic fuel-substrate is 1,4-dihydronicotinamide adenine dinucleotide, NADH. The PQQ-monolayer electrode catalyzes the oxidation of NADH in the presence of Ca²⁺ ions. The MP-11-functionalized electrode catalyzes the reduction of H₂O₂. The biofuel cell generates an open-circuit voltage, V_oc, of ca. 320 mV and a short-circuit current density, I_sc, of ca. 30 μA·cm⁻². The maximum electrical power, W_max, extracted from the cell is 8 μW at an external load of 3 kΩ. The fill factor of the biofuel cell, f=W_max·I_sc⁻¹·V_oc⁻¹, is ca. 25%.     

Enzyme electrodes with substrate and co-enzyme amplification

The enzyme couples horseradish peroxidase/glucose dehydrogenase, glucose oxidase/glucose dehydrogenase, and cytochrome b₂/lactate dehydrogenase are applied in enzyme electrodes. Based on amplification by the recyclization reactions catalyzed by these two-enzyme systems, NADH, NAD⁺, glucose, lactate and pyruvate, are determined with 8–40-fold increased sensitivity compared to the unamplified reactions. Detection limits are 1.0 × 10^?6 M NADH, 1.2 × 10^?6 M NAD⁺, 8 × 10^?7 M glucose, and 3 × 10^?7 M lactate or pyruvate.     

A pseudo triple-enzyme electrochemical aptasensor based on the amplification of Pt–Pd nanowires and hemin/G-quadruplex

Our present work aimed at developing a pseudo triple-enzyme cascade electrocatalytic electrochemical aptasensor for determination of thrombin with the amplification of alcohol dehydrogenase (ADH)-Pt–Pd nanowires bionanocomposite and hemin/G-quadruplex structure that simultaneously acted as NADH oxidase and HRP-mimicking DNAzyme. With the addition of ethanol to the electrolyte, the ADH immobilized on the Pt–Pd nanowires catalyzed ethanol to acetaldehyde accompanied by NAD⁺ being converted to NADH. Then the hemin/G-quadruplex firstly served as NADH oxidase, converting the produced NADH to NAD⁺ with the concomitant local formation of high concentration of H₂O₂. Subsequently, the hemin/G-quadruplex acted as HRP-mimicking DNAzyme, bioelectrocatalyzing the produced H₂O₂. At the same time, the Pt–Pd nanowires employed in our strategy not only provided a large surface area for immobilizing thrombin binding aptamer (TBA) and ADH, but also served as HRP-mimicking DNAzyme which rapidly bioelectrocatalyzed the reduction of the produced H₂O₂. Thus, such a pseudo triple-enzyme cascade electrochemical aptasensor could greatly promote the electron transfer of hemin and resulted in the dramatic enhancement of electrochemical signal. As a result, a wide dynamic concentration linear range from 0.2 pM to 20 nM with a low detection limit of 0.067 pM for thrombin (TB) determination was obtained. The excellent performance indicated that our strategy was a promising way for ultrasensitive assays in electrochemical aptasensors.     

L-Malate-sensing electrode based on malate dehydrogenase and NADH oxidase

An L-malate-sensing electrode was constructed from an oxygen electrode and a layer containing immobilized malate dehydrogenase (MDH) and NADH oxidase. MDH catalyses the dehydrogenation of L-malate by NAD⁺ and NADH oxidase catalyses the regeneration of NAD⁺ with the use of oxygen. The regeneration enables the L-malate oxidation to proceed efficiently even in a medium of neutral pH. At pH 8.0, L-malate in the concentration range 5 μM–1.5 mM can be measured. The relative standard deviation for the measurement is 1.2% (L-malate concentration, 0.2 mM; n=10). The present L-malate-sensing electrode is stable for 8 weeks. A two-electrode sensor system consisting of the L-malate-sensing electrode and an L-lactate-sensing electrode based on lactate oxidase was prepared and applied to the simultaneous determination of the two components in wines.     

Attempting to remove the substrate inhibition ofL-lactate dehydrogenase fromBacillus stearothermophilus by site-directed mutagenesis

L-lactate dehydrogenase (LDH) catalyzes the interconversion of an oxoacid (pyruvate) and hydroxy-acid (lactate) using the NADH/NAD⁺ pair as a redox cofactor. The enzyme has a commercial significance, as it can be used to produce chiral building blocks for the synthesis of key pharmaceuticals and agrochemicals. However, the substrate inhibition which is due to an abortive NAD⁺-pyruvate complex reducing the steady state concentration of functional LDH limits its use in industry. This substrate inhibition can be overcome by weaking the binding of NAD⁺. The conserved aspartic acid residue at position 38 was replaced by the longer basic arginine side chain (D38R) using PCR based overlap extension mutagenesis technique in the hope of weakening NAD⁺-binding. The mutant gene was overexpressed in theEscherichia coli high-expression vector pKK223-3 in JM105 cells; then, the mutant protein was produced. Comparing the effect of substrate inhibition in the arginine-38 mutant with wild-type, substrate inhibition is decreased threefold.     

Albumin coated CuInS2 quantum dots as a near-infrared fluorescent probe for NADH, and their application to an assay for pyruvate

Water-soluble CuInS₂ quantum dots (QDs) stabilized with 3-mercaptopropionic acid were synthesized in aqueous solution and then coated with bovine serum albumin. The resulting particles display fluorescence with a peak at 680 nm that is effectively quenched by 1, 4-dihydro-nicotinamide adenine dinucleotide (NADH), but not by 1, 4-nicotinamide adenine dinucleotide (NAD⁺). The enzyme lactate dehydrogenase catalyzes the reduction of pyruvate and dehydrogenation of lactic acid using NAD⁺ or NADH as a cosubstrate. The new QDs were applied to monitor the course of lactate dehydrogenase-catalyzed reaction of pyruvate by detecting NADH via its quenching effect. This resulted in a convenient and selective detection scheme for pyruvate. The detection limit is as low as 25 nM.

A Miniature glucose/O2 biofuel cell with single-walled carbon nanotubes-modified carbon fiber microelectrodes as the substrate

This study demonstrates a new kind of miniature glucose/O₂ biofuel cells (BFCs) based on carbon fiber microelectrodes (CFMEs) modified with single-walled carbon nanotubes (SWNTs). SWNTs are used as a support both for stably confining the electrocatalyst (i.e., methylene green, MG) for the oxidation of NADH and the anodic biocatalyst (i.e., NAD⁺-dependent glucose dehydrogenase, GDH) for the oxidation of glucose and for efficiently facilitating direct electrochemistry of the cathodic biocatalyst (i.e., laccase) for the O₂ reduction. The prepared micro-sized GDH-based bioanode and laccase-based biocathode exhibit good bioelectrocatalytic activity toward the oxidation of glucose and the reduction of oxygen, respectively. In 0.10 M phosphate buffer containing 10 mM NAD⁺ and 45 mM glucose under ambient air, the power density of the assembled miniature compartment-less glucose/O₂ BFC reaches 58 μW cm⁻² at 0.40 V. The stability of the miniature glucose/O₂ BFC is also evaluated.     

Development of a Carbon Paste Electrode for Lactate Detection Based on Meldola’s Blue Adsorbed on Silica Gel Modified with Niobium Oxide and Lactate Oxidase

A reagentless amperometric biosensor sensitive to lactate was developed. The sensor employs a carbon paste electrode modified with lactate oxidase (LOx) and Meldola’s Blue (MB) adsorbed on silica gel coated with niobium oxide. The dependence on the biosensor response was investigated in terms of pH, supporting electrolyte, ionic strength, lactate oxidase (LOx) amounts and applied potential. The biosensor showed an excellent operational stability (96 % of the activity was maintained after 150 determinations) and storage stability (allowing measurements for more than 1.5 months, when stored in a refrigerator). The proposed biosensor also presented good sensitivity allowing lactate quantification at levels down to 6.5×10^?7 mol L^?1. Moreover, the biosensor showed a good linear response range (from 0.1 to 5.0 mmol L^?1 for lactate). Lactate analysis in biological samples such as blood was also performed. The precision of the data obtained by the proposed biosensor showed reliable results for real complex matrices.     

Biomimetic Oxidation of Aldehyde with NAD+ Models: Glycolysis-Type Hydrogen Transfer in an NAD+/NADH Model System

Just like in biological systems , the GAPDH-catalyzed oxidation of aldehyde to carboxylate proceeds in conjunction with 1,4-selective reduction of NAD⁺ to NADH model compounds [Eq. (1)]. The combination of GAPDH- and LDH-type transfer reactions is also described here as a system mimic for the NAD⁺/NADH redox cycle in anaerobic glycolysis. GAPDH=D -glyceraldehyde-3-phosphate dehydrogenase, LDH=L -lactate dehydrogenase.     

Removal of multiple pollutants from water using noble Ag/Au/magnetite/graphene/H2O2 system under light and ultrasound irradiation

Ag/Au/Fe₃O₄/graphene composites prepared by a hydrothermal method demonstrated excellent activation of H₂O₂ and were used to degrade methylene blue (MB) in solution in the presence of organic acids and inorganic ions under light and ultrasound irradiation. The physicochemical properties of the obtained composites were characterized using various methods. The results showed that the composites exhibited excellent magnetic properties, crystallinity, and stability. The results of catalysis experiments revealed that the removal efficiency of MB increased when Ag and Au were both incorporated into the Fe₃O₄/graphene/H₂O₂ system compared with the removal efficiency achieved with separate Ag-Fe₃O₄/graphene/H₂O₂ and Au-Fe₃O₄/graphene/H₂O₂ systems, indicating a substantial synergistic interaction between the two metallic nanoparticles and the Fe₃O₄/graphene/H₂O₂ systems. The presence of an organic acid accelerated degradation of the MB/H₂O₂ system, whereas almost all of the investigated anions inhibited the degradation of MB; their inhibition effects followed the order CO₃^2? > NO₃^? > Cl^? > F^? > H₂PO₄^? > SO₄^2? > I^?. Cations of Na⁺, K⁺, Ca²⁺, and Mg²⁺ also suppressed MB degradation, likely because of the influence of Cl^? coexisting in the solutions.     

Synergistic effect of mediator–carbon nanotube composites for dehydrogenases and peroxidases based biosensors

Very sensitive, low cost and reliable NADH and H₂O₂ sensors were realised and used for development of enzyme based biosensors. The active surface of the electrodes was modified with a nanocomposite obtained by modification of SWNT with a proper mediator: Meldola Blue (for NADH) and Prussian Blue (for H₂O₂). Low applied potential of − 50 mV vs. Ag/AgCl reference electrode proved the synergistic effect of nanocomposite materials towards NADH and H₂O₂ detection. Biosensors for malic acid and alkylphenols have been developed, using mediator-functionalised-SWNT-based electrodes and two different classes of enzymes: NAD⁺-dependent dehydrogenases and peroxidases. Immobilization of the enzymes was realised using a series of different procedures — adsorption, Nafion membrane, sol–gel and glutaraldehyde, in order to find the best configuration for a good operational stability. A higher sensitivity comparing with other reported biosensors of about 12.41 mA/M·cm² was obtained for l-malic acid biosensor with enzyme immobilised in Nafion membrane. Phenol, 4-t-octylphenol and 4-n-nonylphenol were used as standard compounds for HRP based biosensor. Fast biosensor response and comparable detection limit with HPLC methods were achieved.     

Flow injection analysis for L-lactate with immobilized lactate dehydrogenase

Immobilized lactate dehydrogenase (LDH) is used for determination of L-lactate in a continuous flow system. The LDH is immobilized by reaction with glutaraldehyde onto the surface of alkylamino-bonded silica gel and packed into a column in the flow system. The reduction of NAD⁺ occurs simultaneously, and the NADH formed is detected amperometrically. The peak current is linearly related to the L-lactate concentration in the range 1–80 × 10^-6 M; 30 samples h^-1 can be analyzed with a r.s.d. of 0.5–1.5%. The immobilized LDH retains over 90% of its initial activity after repetitive use for 3 months.     

Quantification of green fluorescent protein in cellular supernatant by capillary electrophoresis with laser-induced fluorescence detection for measurement of cell death

A common method for quantifying cell death is measuring the concentration of lactate dehydrogenase (LDH) released by cells as their membranes become unstable. In cells expressing green fluorescent protein (GFP), degradation of the cell membrane also results in the release of GFP into the surrounding supernatant. In this study, we used capillary electrophoresis with laser-induced fluorescence detection to measure the levels of GFP in supernatants of UBIGFP/BL6 primary macrophages that had been infected with Salmonella typhimurium, treated with staurosporine, or exposed to H₂O₂, all known inducers of cell death. We also used a standard LDH assay to measure the release of LDH into supernatants. We observed the rate of cell death quantified by release of GFP and LDH into supernatant to be essentially identical, demonstrating that GFP release is at least as good as an indicator of macrophage cell death as the established LDH release method.