Electrochemical Investigation of Glucose on a Highly Sensitive Nickel‐Copper Modified Pencil Graphite Electrode

Novel nickel‐copper modified pencil graphite electrode (Ni?Cu/PGE) was fabricated and used as non‐enzymatic sensor for glucose determination. Ni and copper were electrodeposited on PGE using cyclic voltammetry. Morphology and composition of the modified PGE electrode were characterized by field‐emission gun scanning electron microscopy (FEG‐SEM), energy‐dispersive X‐ray spectroscopy (EDX) and Fourier transform infrared spectroscopy (FT‐IR). Electrochemical oxidation of glucose was evaluated by cyclic voltammetry as well as by amperometry. Electrochemical measurements indicate that the Ni?Cu/PGE exhibits a high sensitivity of 2951 μA mM^?1 cm^?2, and a low detection limit of 0.99 μM which are, respectively, three times higher and twice lower than that on Ni/PGE prepared in the same conditions. Moreover, Ni?Cu/PGE exhibits a wider linear range from 1 to 10000 μM with a rapid response time within 2 s. Moreover, Ni?Cu/PGE showed a remarkable stability. The electrode was successfully applied for determination of glucose concentration in human blood without significant interference from potential endogenic interferents. The good applicability of the elaborated sensor made Ni?Cu/PGE promising for the development of effective and inexpensive non‐enzymatic glucose sensor.     

Highly Sensitive and Selective Determination of Dopamine Based on Graphite Nanosheet‐Nafion Composite Film Modified Electrode

A graphite nanosheet (GNS)‐Nafion modified glassy carbon (GC) electrode was prepared and used for highly sensitive and selective determination of dopamine (DA). The GNS‐Nafion/GC electrode displayed excellent electrocatalytic activities towards DA and ascorbic acid (AA). The selective determination of DA was carried out successfully in the presence of AA by differential pulse voltammetry. High sensitivity (3.695 μA μM^?1) and low detection limit (0.02 μM, S/N=3) for the DA detection were obtained. These good properties can be attributed to a large amount of edge plane defects presented on GNSs and the charge‐exclusion and concentration features of Nafion.     

Development of Simple Electrochemical Sensor for Selective Determination of Methadone in Biological Samples Using Multi‐walled Carbon Nanotubes Modified Pencil Graphite Electrode

The electrochemical sensor was developed for determination of methadone (MTD) using multi‐walled carbon nanotubes (MWCNT) modified pencil graphite electrode (MWCNT‐PGE). It was found that the oxidation peak current of MTD at the MWCNT‐PGE was greatly improved compared with that of the bare‐PGE. At the MWCNT‐PGE, well‐defined anodic peak of MTD was observed at about 0.7 V (in pH 7 solution). The influence of several parameters on the determination of MTD was investigated. At optimum experimental conditions, differential pulse voltammetry (DPV) was used for determination of MTD, which exhibited a linear calibration graph of Ip versus MTD concentration in the range of 0.1–15 µM with a correlation coefficient of 0.9992. The calculated detection limit for S/N = 3 was 87 nM. It has been shown that the peaks obtained for oxidation of ascorbic acid (AA), uric acid (UA) and MTD in their mixture could be well resolved by differential pulse voltammetry, permitting us to develop a sensitive and selective electrochemical sensor for determination of MTD in the presence of AA and UA. Finally, MWCNT‐PGE was used for determination of MTD in biological samples, such as human serum and urine, using the standard addition procedure and the results were quite promising.     

Nanosized SnO2 Particles Dispersed on a Graphite Electrode for Selective Detection of Dopamine and Ascorbic Acid

A novel nano-SnO2/graphite electrode has been prepared via polishing procedure to produce active and stable surface. The modified electrode resolves the overlapping voltammetric response of dopamine and ascorbic acid into two well-defined peaks by 230mV. The mechanism of discrimination of dopamine from ascorbic acid is discussed. Dopamine and ascorbic acid can be determined simultaneously with the modified electrode. The electrode shows good sensitivity,slectivity and stability.     

Nickel and Tungsten Bimetallic Nanoparticles Modified Pencil Graphite Electrode: A High-performance Electrochemical Sensor for Detection of Endocrine Disruptor Bisphenol A

In this work, an economically viable, very low cost, indigenous, ubiquitously available electrochemical sensor based on bimetallic nickel and tungsten nanoparticles modified pencil graphite electrode (NiNP-WNP@PGE) was fabricated for the sensitive and selective detection of bisphenol A (BPA). The NiNP-WNP@PGE sensor was prepared by a facile electrochemical one step co-deposition method. The prepared nanocomposite was morphologically characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), electrochemically by cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The proposed sensor displayed high electrocatalytic activity towards electro-oxidation of BPA with one irreversible peak. The fabricated sensor displayed a wide detection window between 0.025 μM and 250 μM with a limit of detection of 0.012 μM. PGE sensor was successfully engaged for the detection of BPA in bottled water, biological, and baby glass samples.     

A Simple and Novel Electrochemical Sensor Based on Phosphomolybdic‐Polypyrrole Film Modified Electrode for Highly Sensitive Detection of Cholic Acid

A simpe electrochemical sensor for detection of cholic acid (CA) was designed by modifying phosphomolybdate (PMo₁₂) doped polypyrrole (PPy) film on glassy carbon electrode (PMo₁₂‐PPy/GCE). The electrochemical behavior of CA on PMo₁₂‐PPy/GCE was investigated by cyclic voltammetry and 0.5 order differential voltammetry. The results indicated that CA had high inhibitory activity toward the peak currents of PMo₁₂‐PPy/GCE. The reduction peak currents were linearly related to the logarithmic value of the concentration of CA from 1.0×10^?7 to 1.0×10^?3 mol/L with a low detection limit of 1.0×10^?8 mol/L. The developed sensor exhibited excellent sensitivity, selectivity and stability for detection of CA, and it could be successfully applied to detect the level of CA in the urine samples. Moreover, the response mechanism of CA on the PMo₁₂‐PPy/GCE was discussed in detail.     

Alumina Polished Glassy Carbon Electrode as a Simple Electrode for Lower Potential Electrochemical Detection of Dopamine in its Sub‐micromolar Level

The electrochemical behaviour of dopamine (DA) at a cleaned and alumina polished glassy carbon electrode (GCE) was studied using cyclic voltammetry (CV). The CV studies revealed that alumina polished GCE (AGCE) shows an enhanced oxidation peak current response with 217 mV negative potential shift towards DA than that of cleaned GCE. The differential pulse voltammetry result shows that the AGCE detects the DA in the linear concentration ranges from 0.15 to 25.25 µmol L^?1. The limit of detection was calculated as 0.046 µmol L^?1 with a sensitivity of 3.74 µA µmol L^?1 cm^?2 for the determination of DA. The fabricated AGCE shows a satisfactory selectivity, practicality along with appreciable repeatability and reproducibility.     

Selective and Sensitive Electrochemical Sensor for L‐Methionine at Physiological pH Using Functionalized Triazole Polymer Film Modified Electrode

This communication describes the determination of an essential amino acid, L ‐methionine (L ‐Met) in the presence of important interferents, ascorbic acid (AA) and uric acid (UA) at physiological pH using a glassy carbon electrode modified with an electropolymerized film of 3‐amino‐5‐mercapto‐1,2,4‐triazole (p‐AMTa). The bare glassy carbon electrode fails to show a voltammetric signal for L ‐Met in the presence of AA and UA at pH 7.2. However, the p‐AMTa electrode separates the voltammetric signals of AA, UA and L ‐Met with pronounced oxidation currents. The amperometric current of L ‐Met was increased linearly from 1.0×10^?7 to 1×10^?4 M and the detection limit was found to be 4.12×10^?10 M (S/N=3).     

SE‐30 Graphite Composite Electrode: An Alternative for the Development of Electrochemical Biosensors

A new graphite composite electrode was constructed by mixing graphite powder with chromatography stationary phase, SE‐30, as the binder. The electrochemical behavior of the new electrode has been evaluated and compared with that of traditional carbon paste electrode (CPE). The proposed electrode provides a remarkable increase in the rate of electron transfer of biomolecules such as nicotinamide adenine dinucleotide (NADH), cysteine, ascorbic acid and catechol and shows a low surface fouling effects. The electrode shows highly promising results when used as an amperometic sensor for biocompounds such as NADH.     

Real‐time Selective Detection of Hydrogen Peroxide Based on a Tantalum Deposited Pencil Lead Electrode for Evaluation of Enzyme Activities

In this study, we have carried out electrodeposition of tantalum (Ta) nanostructures on pencil lead electrode in non‐aqueous media at room temperature by applying a constant potential. The deposited Ta on pencil lead was examined for the catalytic effect regarding hydrogen peroxide (H₂O₂) reduction with voltammetry and amperometry. Ta/pencil lead electrode exhibited amperometric sensitivity of 0.317 μA mM⁻¹ cm⁻² and fast response time of 0.75 s, where selective detection of H₂O₂ was fulfilled without interruption from common electroactive biomaterials such as O₂, uric acid, ascorbic acid, dopamine, acetamidophenol, and glucose. For practical applications, the dynamic concentration changes of H₂O₂ during catalase and glucose oxidase‐involved reactions, either eliminating or producing H₂O₂, were successfully traced in real time with as‐prepared electrode. From the kinetics study for catalase and glucose oxidase, we evaluated Michaelis constants (K _m^app) as 7.8 mM for catalase and 37 mM for glucose oxidase, respectively.     

Highly Sensitive Enzyme-free Sensor Based on a Carbon Paste Electrode Modified with Binary Zinc Oxide/Polyaniline Nanocomposites for Dopamine,Ascorbic Acid and Uric Acid Sensing

Hybrid composites ZnO/PANI were facily synthesized by a sonication process at room temperature. This procedure is non-expensive, time/energy saving and environmentally safe. The as-prepared ZnO/PANI were characterized by FTIR, UV-vis spectroscopies and SEM in order to investigate the structure and morphology of the studied composites. The samples were used to modify carbon paste electrode (CPE) in order to develop electrochemical biosensors (ZnO/PANI/CPE). The sensing properties of the nanoparticles were evaluated for dopamine, ascorbic acid and uric acid non-enzymatic detection. The effect of percentage of polyaniline in the composites and the effect of calcination on the biosensor's response were also examined in the present study. It was revealed that the existence of PANI in ZnO/PANI/CPE largely enhanced the electroactive surface area and therefore the sensitivity for electrochemical sensing. A good electrochemical behavior was noted for ZnO/40 wt% PANI-cal/CPE modified electrode toward DA, AA and UA oxidation. The electroactive surface area of the previously mentioned modified electrode (0.235 cm²) was two times higher than that of the bare electrode (0.117 cm²). The liner relationships between current intensities and concentrations were found to be 0.01–1.4 mM, 0.1–1.3 mM and 0.01–0.12 mM, with detection limit of 0.029 mM, 0.063 mM and 0.007 mM, for DA, AA and UA respectively. In the mixtures of ascorbic acid (AA), dopamine (DA) uric acid (UA) and glucose (Glu) the sensor showed high selectivity of DA with low interference of ascorbic acid by a current change of 14 %. The as-prepared ZnO/PANI/CPE biosensor displayed a good reproducibility and stability.     

Selective Electrochemical Epinephrine Sensor Using Self‐Assembled Monomolecular Film of 1,8,15,22‐Tetraaminophthalocyanatonickel(II) on Gold Electrode

This article describes the highly sensitive and selective determination of epinephrine (EP) using self‐assembled monomolecular film (SAMF) of 1,8,15,22‐tetraamino‐phthalocyanatonickel(II) (4α‐Ni^IITAPc) on Au electrode. The 4α‐Ni^IITAPc SAMF modified electrode was prepared by spontaneous adsorption of 4α‐Ni^IITAPc from dimethylformamide solution. The modified electrode oxidizes EP at less over potential with enhanced current response in contrast to the bare Au electrode. The standard heterogeneous rate constant (k°) for the oxidation of EP at 4α‐Ni^IITAPc SAMF modified electrode was found to be 1.94×10^?2 cm s^?1 which was much higher than that at the bare Au electrode. Further, it was found that 4α‐Ni^IITAPc SAMF modified electrode separates the voltammetric signals of ascorbic acid (AA) and EP with a peak separation of 250 mV. Using amperometric method the lowest detection limit of 50 nM of EP was achieved at SAMF modified electrode. Simultaneous amperometric determination of AA and EP was also achieved at the SAMF modified electrode. Common physiological interferents such as uric acid, glucose, urea and NaCl do not interfere within the potential window of EP oxidation. The present 4α‐Ni^IITAPc SAMF modified electrode was also successfully applied to determine the concentration of EP in commercially available injection.     

Fabrication of Nano Flower‐shaped Platinum on Glassy Carbon Electrode as a Sensitive Sensor for Lead Electrochemical Analysis

Platinum nanoflowers modified glassy carbon electrodes (PtNFs/GCE) was fabricated simply for lead determination in water samples. The modified electrodes were prepared by electrodeposition in hexachloroplatinic acid solution at constant potential. The influence of deposition time and potential on surface morphology, chemical composition, electrochemical properties of electrode were investigated. At ?0.2 V of potential and 150 s of deposition duration, platinum developed as nanoflower shape and scattered densely all over the glassy carbon surface, producing the largest electrochemically active surface areas. The highest differential pulse stripping voltammetry (DPSV) signal of lead was obtained by using the prepared electrode. Under optimized experimental condition of electrolyte, accumulation potential and time, the peak current was found to be linear proportion to lead concentration in range of 1 to 100 μg L^?1 (slope=0.371) with a limit of detection of 0.398 μg L^?1. The method has good repeatability and reproducibility with relative standard deviations of 1.47 % and 4.83 %, respectively. The modified PtNFs/GCE also demonstrated an excellent long‐term stability with only 9 % decrease in Pb peak current over 30 days. Moreover, the performance of the modified PtNFs/GCE in determination of Pb(II) in two industrial wastewaters was good agreement with data obtained by a graphite furnace atomic absorption spectrometry (GFAAS) method.     

Electrochemical Sensor for the Determination of Dopamine in Presence of High Concentration of Ascorbic Acid Using a Fullerene‐C60 Coated Gold Electrode

A fullerene‐C₆₀‐modified gold electrode is employed for the determination of dopamine in the excess of ascorbic acid using square‐wave voltammetry. Based on its strong catalytic function towards the oxidation of dopamine and ascorbic acid, the overlapping voltammetric response of both the biomolecules at the bare electrode is resolved into two well‐defined voltammetric peaks with lowered oxidation potential and enhanced oxidation currents. Linear calibration curves for dopamine are obtained using square‐wave voltammetry over the concentration range 1 nM–5.0 μM in 0.1 M phosphate buffer solution at pH 7.2 with a correlation coefficient of 0.9931 and the detection limit (3σ) is estimated to be 0.26×10^?9 M. The interference studies showed that the presence of physiologically common interferents (i.e. uric acid, citric acid, tartaric acid, glucose and sodium chloride) negligibly affects the response of dopamine. The practical analytical utility of the method is illustrated by quantitative determination of dopamine in commercially available pharmaceutical formulation and human body fluids, viz. urine and blood plasma, without any preliminary treatment.     

A Simple and Highly Sensitive Electrochemically Reduced p‐Nitrobenzoic Acid Film Modified Sensor for Determination of Mercury

Herein, a simple electrochemical sensor was fabricated for sensing Hg²⁺ ions by using electrochemically reduced p‐nitrobenzoic acid molecules modified (ERpNBA) glassy carbon electrode (GCE). The modified electrode was applied for the determination of Hg²⁺ ions by using differential pulse anodic stripping voltammetry (DPASV). Experimental parameters such as concentration of p‐nitrobenzoic acid used for electrode modification, pH, accumulation time and deposition potential used for the determination of Hg²⁺ ions were optimized. The strong interaction between the Hg²⁺ ions and the lone pair of electrons on the nitrogen atoms of ERpNBA molecules leads to highly selective adsorption of Hg²⁺ ions on the modified electrode. Under the optimum experimental conditions, the sensor showed higher sensitivity and very low detection limit for Hg²⁺ ions than other metal ions such as Cd²⁺, Pb²⁺ and Zn²⁺ ions. The LOD for Hg²⁺ ions was 240 pM which is below the guideline value given by the World Health Organization and the earlier reports.     

A Coated Graphite Thorium‐Ion Selective Potentiometric Sensor Based on a Calix[4]arene Bearing Phosphoryl Groups

5,11,17,23‐Tetra‐tert‐butyl‐25,26,27,28‐tetrakis(diphenylphosphinoylmethoxy)calix[4]arene ( 1 )has been used for the preparation of a graphite coated thorium ion‐selective electrode (Th⁴⁺‐ISE). The plasticized PVC membrane containing 30% PVC, 58% ortho‐nitrophenyloctylether (NPOE), 4% sodium tetraphenylborate (NaTPB) and 8% ionophore was directly coated on a graphite rod. This sensor gave good Nernstian responses with a slope of 15.5 ± 0.1 mV/decade over a concentration range of 1 × 10^?5 ?1 × 10^?3 M of thorium ions with a limit of detection of 7.9 × 10^?6 M. The dynamic response time of the electrode to achieve a steady potential was found to be about 15 seconds. The potential of the prepared sensor was independent of the pH variation in the range 2.3–4.0. The selectivity relative to several mono‐, di‐ and tri‐valent metal ions, i.e. Li⁺, Na⁺, K⁺, Ag⁺, NH₄⁺, Sr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, La³⁺, Sm³⁺, Dy³⁺, Er³⁺ and Y³⁺ was examined. This electrode can be used for 6 months without any considerable divergences in the potential response. The sensor was successfully used as an indicator electrode for the potentiometric titration of a thorium solution using a standard solution of EDTA.     

Zinc Oxide Nanoparticle‐modified Glassy Carbon Electrode as a Highly Sensitive Electrochemical Sensor for the Detection of Caffeine

Zinc oxide nanoparticles (ZnO NPs ) were prepared by a simple, convenient, and cost‐effective wet chemical method using the biopolymer starch. The prepared ZnO NPs were characterized by X‐ray diffraction (XRD ), scanning electron microscopy (SEM ), energy‐dispersive X‐ray (EDX ), Fourier transform infrared (FT‐IR ), and UV ‐visible spectroscopic techniques. The average crystallite size calculated from XRD data using the Debye–Scherer equation was found to be 15 nm. The electrochemical behavior of caffeine (CAF ) was studied using a glassy carbon electrode (GCE ) modified with zinc oxide nanoparticles by cyclic voltammetry (CV ) and differential pulse voltammetry (DPV ). Compared to unmodified GCE , ZnO NPs‐ modified GCE (ZnO NPs MGCE ) exhibited excellent electrocatalytic activity towards CAF oxidation, which was evident from the increase in the peak current and decrease in the peak potential. Electrochemical impedance study suggested that the charge‐transfer capacity of GCE was significantly enhanced by ZnO NPs . The linear response of the peak current on the concentrations of CAF was in the range 2–100 μM . The detection limit was found to be 0.038 μM. The proposed sensor was successfully employed for the determination of CAF in commercial beverage samples.     

基于乙硫基取代的三层酞菁铕二聚体修饰ITO电极构筑电化学多巴胺和尿酸传感器

通过在水平和垂直两个方向上来扩展酞菁配合物的共轭结构, 合成了三明治三层酞菁铕二聚体配合物[Pc(SC₂H₅)₈]₂Eu₂[BiPc(SC₂H₅)₁₂]Eu₂[Pc(SC₂H₅)₈]₂, 使用Quasi-Langmuir-Sh?fer(QLS)方法将配合物薄膜修饰在氧化铟锡导电玻璃(ITO)电极表面, 利用多种谱学手段对配合物分子在薄膜内的排列进行表征, 发现分子采取J聚集模式Edge-on排列在ITO电极表面, 该薄膜具有良好的半导体性质, 导电率高达8.86×10^-5 S/cm. 将配合物薄膜修饰的ITO电极成功应用于多巴胺(DA)和尿酸(UA)的电化学灵敏检测, 最低检测限分别达到1.35和1.64 μmol/L, 灵敏度分别达到110和186.5 mA·μL·mol^-1 ·cm^-2.     

Ni3S2 Supported on Porous Ball‐milled Silicon,a Highly Selective Electrochemical Sensor for Glucose Determination

In this work, an electrochemical sensor based on Ni₃S₂ nanoparticles supported on porous ball‐milled silicon was fabricated for measuring glucose. At first, the glassy carbon electrode (GCE) surface was modified by Ni₃S₂ nanoparticles supported on a porous ball‐milled silicon substrate. To characterize the modified electrode, N₂ adsorption‐desorption isotherms and BHJ, transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy‐dispersive X‐ray spectroscopy (EDX), elemental mapping and X‐ray diffraction (XRD) were used. In the following, the effective parameters on the sensor response such as pH, NaOH concentration, catalyst concentration, applied potential, and rotational speed of the electrode were optimized using cyclic voltammetric (CV) and hydrodynamic amperometric methods. Under the optimal conditions, the calibration curve was plotted using the hydrodynamic amperometric method. Three linear regions were obtained from 0.5–134, 134–1246, and 1246–3546 μM, with a detection limit of 0.2 μM for glucose. Finally, the proposed method was used for measuring glucose levels in human blood serums.