Development of an Electrochemical Sensor Based on Covalent Molecular Imprinting for Selective Determination of Bisphenol‐A

In this study, an electrochemical sensor was developed and used for selective determination of bisfenol‐A (BPA) by integrating sol‐gel technique and multi‐walled carbon nanotubes (MWCNTs) modified paste electrode. BPA bounded by covalently to isocyanatopropyl‐triethoxy silane (ICPTS) was synthesized as a new precursor (BPA‐ICPTS) and then BPA‐imprinted polymer (BPA‐IP) sol‐gel was prepared by using tetramethoxysilane (TMOS) and BPA‐ICPTS. Non‐imprinted polymer (NIP) sol‐gel was obtained by using TMOS and (3‐Aminopropyl) triethoxysilane. Both BPA‐IP and NIP sol‐gels were characterized by nitrogen adsorption‐desorption analysis, FTIR, SEM, particle size analyzer and optical microscope. Carbon paste sensor electrode was fabricated by mixing the newly synthesized BPA‐IP with MWCNTs, graphite powder and paraffin oil. The electrochemical characterization of the sensor electrode was achieved with cyclic and differential pulse voltammetric techniques. The response of the developed sensor under the most proper conditions was linear in BPA concentration range from 4.0×10⁻⁹ to 1.0×10⁻⁷ mol L⁻¹ and 5.0×10⁻⁷ to 5.0×10⁻⁵ mol L⁻¹ and the detection limit was 4.4×10⁻⁹ mol L⁻¹. The results unclosed that the proposed sensor displayed high sensitivity and selectivity, superior electrochemical performance and rapid response to BPA.     

A Potentiometric Sensor for Cd2+ Based on Carbon Nanotube Paste Electrode Constructed from Room Temperature Ionic Liquid,Ionophore and Silica Nanoparticles

A novel and effective potentiometric sensor for the rapid determination of Cd²⁺ based on carbon paste electrode consisting of the room temperature ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate, multiwalled carbon nanotubes, silica nanoparticles and ionophore was constructed. The prepared composite has a low potential drift, high selectivity and fast response time, which leads to a more stable potential signal. A linear dynamic range of 4.50×10^?9–1.00×10^?1 mol L^?1 with a detection limit of 2.00×10^?9 mol L^?1 was obtained. The modified electrode was successfully applied to the accurate determination of trace amounts of Cd²⁺ in environmental and biological samples.     

A new Approach for the Voltammetric Sensing of the Phytoestrogen Genistein at a Non-modified Boron-doped Diamond Electrode

An effective electrochemical sensor was constructed using an unmodified boron-doped diamond electrode for determination of genistein by square-wave voltammetry. Cyclic voltammetric investigations of genistein with HClO₄ solution indicated that irreversible behavior, adsorption-controlled and well-defined two oxidation peaks at about +0.92 (P_A1) & +1.27 V (P_A2). pH, as well as supporting electrolytes, are important in genistein oxidations. Quantification analyses of genistein were conducted using its two oxidation peaks. Using optimized experiments as well as instrumental conditions, the current response with genistein was proportionately linear in the concentrations range of 0.1 to 50.0 μg mL⁻¹ (3.7×10⁻⁷−1.9×10⁻⁴ mol L⁻¹), by the detection limit of 0.023 μg mL⁻¹ (8.5×10⁻⁸ mol L⁻¹) for P_A1 and 0.028 μg mL⁻¹ (1.1×10⁻⁷ mol L⁻¹) for P_A2 in 0.1 mol L⁻¹ HClO₄ solution (in the open circuit condition at 30 s accumulation time). Ultimately, the developed method was effectively applied to detect genistein in model human urine samples by using its second oxidation peak (P_A2).     

Comparative Study of Lead(II) Selective Poly(vinyl chloride) Membrane Electrodes Based on Podand Derivatives as Ionophores

The two podand chelates based on diethylsulfide, 1,5‐bis(2′‐hydroxy‐4′‐nitrophenoxy)‐3‐thiapentane (L₁) and 1,5‐bis(8′‐oxybenzopyridine)‐3‐thia pentane (L₂), have been synthesized and explored as neutral ionophores for preparing poly(vinyl chloride) based membrane electrodes selective to Pb²⁺. The addition of anionic additives and various plasticizers has been found to substantially improve the performance of the electrode. The best performance was obtained with the electrode No. 1 having a membrane of ionophore (L₁) with the composition PVC:o‐NPOE:ionophore (L₁):NaTFPB (%w/w) of 33 : 62 : 3 : 2. The electrode exhibits Nernstian response with a slope of 31.57±0.3 mV decade^?1 of activity in the concentration range from 2.0×10^?9 to 1.0×10^?1 M Pb²⁺, performs satisfactorily over a wide pH range (1.6–7.0), with a fast response time (5 s).     

Novel potentiometric sensor for the determination of Cd2+ based on a new nano-composite

A novel ion selective carbon paste electrode for Cd²⁺ ions based on 2,2′-thio-bis[4-methyl(2-amino phenoxy) phenyl ether] (TBMAPPE) as an ionophore was prepared. The carbon paste was made based on a new nano-composite including multi-walled carbon nanotubes (MWCNTs), nanosilica and room-temperature ionic liquid, 1-Butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆). The constructed nano-composite electrode showed better sensitivity, selectivity, response time, response stability and lifetime in comparison with typical Cd²⁺ carbon paste sensor for the successful determination of Cd²⁺ ions in water and in waste water samples. The best performance for nano-composite sensor was obtained with an electrode composition of 18% TBMAPPE, 20% BMIM-PF₆, 48% graphite powder, 10% MWCNT and 4% nanosilica. The new electrode exhibited a Nernstian response (29.95?±?0.10?mV?decade^?1) toward Cd²⁺ ions in the range of 3.0?×?10^?8 to 1.0?×?10^?1?mol?L^?1 with a detection limit of 7.5?×?10^?9?mol?L^?1. The potentiometric response of prepared sensor was independent of the pH of test solution in the pH range 3.0 to 5.5. It had a quick response with a response time of about 6?s. The proposed electrode showed fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions.     

Novel Potentiometric Solid-contact Electrode for the Determination of Fe2+ Ions via MWCNTs-Gemifloxacin Composite

A novel electrode was fabricated for the quantitation of Fe²⁺ ion. It was based on the covalent attachment of the gemifloxacin molecule (the recognition element) to the surface of MWCNTs to be incorporated as an electroactive material. Linear response of Fe²⁺ ions was found in the concentration range of 1×10⁻² mol L⁻¹ to 1×10⁻⁸ mol L⁻¹ with a Nernstian slope of 30.37 ±0.3 (mV/decade) and attained a stable response within 5 s. The sensor exhibited LOD value of 4.8×10⁻⁹ mol L⁻¹. It was applied in the monitoring of Fe²⁺ concentration in multi-vitamins tablets, tap water and milk samples with acceptable recovery ranged from 94.00 % to 102.00 %.     

Copper‐based Metal‐organic Framework Applied in the Development of an Electrochemical Biomimetic Sensor for Catechol Determination

In this study, the synthesis and characterization of a Cu‐based metal‐organic framework (MOF) [Cu₃(BTC)₂(H₂O)₃]_n (where BTC=benzene‐1,3,5‐tricarboxylate), known as HKUST‐1, were performed. The Cu‐MOF was applied in the modification of a carbon paste to obtain a biomimetic sensor for the electrochemical determination of catechol. Kinetic assays confirmed that the Cu‐MOF acts as a catalyst for the oxidation of catechol and it can be considered as a catechol oxidase mimetic. Under optimized conditions, the calibration curve for catechol presented a linear range of 8.0×10⁻⁷ to 3.2×10⁻⁵ mol L⁻¹, with detection limit of=1.0×10⁻⁷ mol L⁻¹. The sensor demonstrated good intra‐day repeatability and inter‐electrode reproducibility (relative standard deviations of 3.8 % (n=10) and 4.3 % (n=6), respectively). In the selectivity study, an adequate peak‐to‐peak separation was observed for hydroquinone and uric acid in relation to catechol, demonstrating that this sensor has the potential for use in the simultaneous determination of these compounds. This sensor was successfully applied in the determination of catechol in water samples.     

Modification of Carbon Paste Electrode Based on Molecularly Imprinted Polymer for Electrochemical Determination of Diazinon in Biological and Environmental Samples

The wide use of pesticides can lead to environmental and human adverse effects. Diazinon, as an organophosphorous pesticide, is used in agriculture because of its low cost and high efficiency on insects. Due to the increasing application of pesticides, accurate analytical methods are necessary. The aim of this work was modification of carbon paste electrode composition and applying it as a sensor for determination of diazinon in biological and environmental samples. Multi‐walls carbon nanotubes and a molecularly imprinted polymer were used as modifiers in the sensor composition. A molecularly imprinted polymer and a non‐imprinted polymer were synthesized for applying in the electrode. After optimization of electrode composition, it was used to determine the analyte concentration. Instrumental parameters affecting the square wave voltammetric response were adjusted to obtain the highest current intensity. The modified electrode with MIP showed very high recognition ability compared to the electrode containing NIP. The obtained linear range was 5×10⁻¹⁰ to 1×10⁻⁶ mol L⁻¹. The detection limit of the sensor was 1.3×10⁻¹⁰ mol L⁻¹ and the relative standard deviation for analysis of target molecule by the proposed sensor was 2.87 %. This sensor was used to determine the diazinon in real samples (human urine, tap, and river water samples) without special sample preparation before analysis. The optimization of electrode composition containing mentioned modifiers improved its response considerably.     

Selective and Sensitive Determination of Uranyl Ions in Complex Matrices by Ion Imprinted Polymers‐Based Electrochemical Sensor

We report on the design of a UO₂²⁺‐selective electrode based on the use of UO₂²⁺ imprinted polymer nanoparticles (IP‐NPs), and its application for the differential pulse adsorptive cathodic stripping voltammetry determination of uranyl ions. A carbon paste electrode was modified with the IP‐NPs, and differential pulse adsorptive cathodic stripping voltammetry was applied as the detection technique after open‐circuit sorption of UO₂²⁺ ions. The modified electrode responses to UO₂²⁺ was linear in the 0.1 µg L^?1 to 10 µg L^?1 and in the 0.01 mg L^?1 to 10 mg L^?1. The method detection limit of the sensor was 0.03 µg L^?1.     

A Newly Competitive Electrochemical Sensor for Sensitive Determination of Chrysin Based on Electrochemically Activated Ta2O5 Particles Modified Carbon Paste Electrode

A novel electrochemically activated doped Ta₂O₅ particles modified carbon paste electrode (EA‐Ta₂O₅‐CPE) was prepared and applied for selective and sensitive determination of chrysin. X‐ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) techniques and cyclic voltammetry (CV) were used to characterize the Ta₂O₅ particles and investigate the electrochemical response of the sensor. Compared with bare CPE, the doped Ta₂O₅ modified electrode got much more porous by electrochemical treatment and exhibited larger effective surface area, more reactive site and excellent electrochemical catalytic activity toward the oxidation of chrysin. Under optimum conditions by LSV, the oxidation peak currents responded to chrysin linearly over a concentration range from 5.0×10⁻⁸ to 7.0×10⁻⁶ mol L⁻¹ with a detection limit of 2.0×10⁻⁸ mol L⁻¹ (5.08 ng mL⁻¹). The fabricated sensor showed anti‐interference ability against the biological common interferents (i.e. baicalein, baicalin) and provided to be reliable for the determination of chrysin in Chinese medicinal herb Oroxylum indicum and chrysin capsules samples with satisfactory results.     

Square Wave‐Anodic Stripping Voltammetric Determination of Copper at a Bismuth Film/Glassy Carbon Electrode Using 3‐[(2‐Mercapto‐Vinyl)‐Hydrazono]‐ 1,3‐Dihydro‐Indol‐2‐One

This study reports a highly sensitive electrochemical sensor based on Bi film modified glassy carbon electrode (BiF/GCE) for total determination and speciation trace concentrations of copper(II) ions in environmental water samples. Square wave‐adsorptive anodic stripping voltammetric (SW‐ASV) experiment was performed for monitoring selective accumulation of copper(II) with reagent 3‐[(2‐mercapto‐vinyl)‐hydrazono]‐1,3‐dihydro‐indol‐2‐one (MHDI) at pH 9–10. The mechanism of the electrode reaction of Cu²⁺‐MHDI complex was safely assigned. The sensor exhibited a wide linear range (3.22×10⁻⁹–2.0×10⁻⁷ mol L⁻¹) with lower limits of detection (LOD) and quantitation (LOQ) of 9.6×1⁻¹⁰ and 3.22×10⁻⁹ mol L⁻¹, respectively (R²=0.9993). The proposed sensor exhibited interference from active metal ions e. g. Cd, Hg. The performance of the proposed method was compared successfully with most of the reported methods and comparable efficiencies were obtained. The analytical utility of the proposed SW‐ASV method has been successfully validated for trace analysis of copper(II) in environmental water samples. The method offers a precise, accurate approach with good reproducibility, robustness, ruggedness, and cost effectiveness.     

Application of 1,4-Diaminoanthraquinone as a New Sensing Material for Fabrication of a Iron(III)-Selective Modified Carbon Paste Electrode

In the present work, a novel sensitive electrochemical potentiometric sensor for sensing Fe³⁺ ions based on 1,4-diaminoanthraquinone (DAQ) as a hydrophobic selector element was prepared to implement as an ion selective carbon paste electrode in the aqueous solutions. The adequate amounts of ionophore (5%), paraffin oil (25%) as a binder, Nanosilica (NS: 0.5%) multi-wall carbon nanotubes (MWCNTs: 1%) as a modifier, and graphite powder (68.5%) as an inert matrix was occupied to form the paste. This new FeCP sensor demonstrated a Nernstian slope of 19.7 ± 0.7 mV per decade over widish linear range between 1.0 × 10^–8 to 1.0 × 10^–2 mol L^–1 at working pH range of 1.9–5.0 in the optimized conditions. The average elapsed time to response of electrode was about ~6 s for concentrations from lower (1.0 × 10^?8 mol L^–1) to higher (1.0 × 10^?2 mol L^–1) of Fe³⁺ ion solution. The selectivity of electrode toward Fe³⁺ ions in comparison with other cations was studied by matched potential method. The making FeCP sensor has been put to use successfully as an indicator electrode in analytical applications such as the potentiometric titration and determination of iron(III) ion in blend of different ions.     

Tapioca Biofilm Containing Nitrogen‐doped Titanium Dioxide Nanoparticles for Electrochemical Detection of 17‐β Estradiol

A novel sensor architecture based on thin film of tapioca decorated within nitrogen‐doped titanium dioxide (N‐TiO₂) nanoparticles is reported. The nanostructures were characterized by scanning electron microscope, transmission electron microscope, X‐rays diffraction and voltammetric techniques. The proposed electrode was used for detection of low concentrations of 17‐β estradiol in without purification step, which was investigated by using linear sweep adsorptive stripping voltammetry. Under optimal conditions, the analytical curve was linear over a 17β‐estradiol concentration range of 9.9×10⁻⁶ to 1.4×10⁻⁵ mol L⁻¹, with a detection limit of 1.7×10⁻⁷ mol L⁻¹. The tapioca and N‐TiO₂ nanoparticles homogeneous film was applied for detection of 17‐β‐estradiol in tap water and synthetic urine samples, which presented satisfactory results.     

An All‐solid‐state Polymeric Membrane Ca2+‐selective Electrode Based on Hydrophobic Alkyl‐chain‐functionalized Graphene Oxide

An all‐solid‐state polymeric membrane Ca²⁺‐selective electrode based on hydrophobic octadecylamine‐functionalized graphene oxide has been developed. The hydrophobic composite in the ion‐selective membrane not only acts as a transduction element to improve the potential stability for the all‐solid‐state Ca²⁺‐selective electrode, but also is used to immobilize Ca²⁺ ionophore with lipophilic side chains through hydrophobic interactions. The developed all‐solid‐state Ca²⁺‐selective electrode shows a stable potential response in the linear range of 3.0×10⁻⁷–1.0×10⁻³ M with a slope of 24.7±0.3 mV/dec, and the detection limit is (1.6±0.2 )×10⁻⁷ M (n =3). Additionally, due to the hydrophobicity and electrical conductivity of the composite, the proposed all‐solid‐state ion‐selective electrode exhibits an improved stability with the absence of water layer between the ion‐selective membrane and the underlying glassy carbon electrode. This work provides a simple, efficient and low‐cost methodology for developing stable and robust all‐solid‐state ion‐selective electrode with ionophore immobilization.     

Quantitative Analysis of Holmium Ion by a Ho3+ Ion‐Selective Sensor Based on a Symmetric Thio‐Schiff's Base

A poly(vinyl chloride) (PVC) membrane sensor for holmium ions was fabricated based on N‐[(Z)‐1‐(2‐thienyl)‐ methylidene]‐N‐[4‐(4‐{[(Z)‐1‐(2‐thienyl)methylidene]amino} phenoxy)phenyl] amine (TPA) as a new ion carrier, acetophenon (AP) as plasticizing solvent mediator and sodium tetraphenyl borate (NaTPB) as an anion excluder. The electrode shows a good selectivity towards Ho³⁺ ions respect to other inorganic cations, including alkali, alkaline earth, transition and heavy metal ions. The constructed sensor displays a Nernstian behavior (19.5±0.3 mV/decade) over the concentration range of 1.0×10⁻⁶ to 1.0×10⁻² mol·L⁻¹ with the detection limit of the electrode being 4.6×10⁻⁷ mol·L⁻¹ and very short response time (ca. 5 s). It has a useful working pH range of 3.2–9.8 for at least 8 weeks. The electrode was successfully applied as an indicator electrode for the potentiometric titration of a Ho³⁺ solution with EDTA and holmium determination in some alloys. The proposed sensor accuracy was studied by the determination of Ho³⁺ in mixtures of three different ions.     

New Copper(II) Ion-Selective Membrane Electrode Based on Erythromycin Ethyl Succinate as a Neutral Ionophore

Abstract

The potentiometric response characteristics of a new copper(II) ion-selective PVC membrane electrode based on erythromycin ethyl succinate (EES) as ionophore were investigated. The electrode exhibited a Nernstian response to Cu²⁺ ions over the activity range of 1.5 × 10^?2 to 2.0 × 10^?6 mol L^?1 with a limit of detection of 6.3 × 10^?7 mol L^?1. Stable potentials were obtained in the pH range of 5.5–6.5. The potentiometric selectivity coefficients were calculated by using fixed interference method and revealed no important interferences except for Ag⁺. This electrode was successfully applied as an indicator electrode in determination of copper ions in real water samples.     

Response Characteristics of Copper‐Selective Polymer Membrane Electrodes Based on a Newly Synthesized Macrocyclic Calix[4]arene Derivative as a Neutral Carrier Ionophore

A novel macrocyclic calix[4]arene derivative was examined as an ionophore for ion‐selective polymeric membrane electrode toward Cu⁺² ions. The sensor showed a near Nernstian response for Cu(II) ions over a concentration range from 8.1×10^?6 to 1.0×10^?2 mol L^?1 with a slope of 34.2±0.4 mV per concentration decade in an acidic solution (pH 5). The limit of detection was 0.47 µg mL^?1. It had a response time of <20 s and can be used for at least 3 months without any divergence in potentials. The influence of plasticizer as well as the amount of lipophilic anionic site additive in the sensing membrane was discussed. It was shown that membrane electrodes formulated with the ionophore and appropriate anionic additive exhibited enhanced potentiometric response toward Cu²⁺ over all other cations tested. Since selectivity toward Cu²⁺ ions is decreased in the presence of high amount of the anionic additive, the ionophore can function as neutral carriers within the organic membrane phase. Validation of the assay method revealed good performance characteristics, including long life span, good selectivity for Cu²⁺ ions over a wide variety of other metal ions, long term response stability, and high reproducibility. The sensors were used for direct measurement of copper content in different rocks collected from different geological zones. The results agreed fairly well with data obtained using atomic absorption spectrometry.     

Lead(II) Potentiometric Sensor Based on 1,4,8,11‐Tetrathiacyclotetradecane Neutral Carrier and Lipophilic Additives

A potentiometric sensor for lead(II) ions based on the use of 1,4,8,11‐tetrathiacyclotetradecane (TTCTD) as a neutral ionophore and potassium tetrakis‐(p‐chlorophenyl)borate as a lipophilic additive in plasticized PVC membranes is developed. The sensor exhibits linear potentiometric response towards lead(II) ions over the concentration range of 1.0×10^?5–1.0×10^?2 mol L^?1 with a Nernstian slope of 29.9 mV decade^?1 and a lower limit of detection of 2.2×10^?6 mol L^?1 Pb(II) ions over the pH range of 3–6.5. Sensor membrane without a lipophilic additive displays poor response. The sensor shows high selectivity for Pb(II) over a wide variety of alkali, alkaline earth and transition metal ions. The sensor shows long life span, high reproducibility, fast response and long term stability. Validation of the method by measuring the lower limit of detection, lower limit of linear range, accuracy, precision and sensitivity reveals good performance characteristics of the proposed sensor. The developed sensor is successfully applied to direct determination of lead(II) in real samples. The sensor is also used as an indicator electrode for the potentiometric titration of Pb(II) with EDTA and potassium chromate. The results obtained agree fairly well with data obtained by AAS.     

Simultaneous Voltammetric Determination of Paracetamol,Codeine and Caffeine on Diamond‐like Carbon Porous Electrodes

A porous electrode material combining the features of vertically aligned multi‐walled carbon nanotubes (VAMWCNT) and diamond‐like carbon films (DLC) have been developed for a highly sensitive electrochemical sensor. For working electrode preparation, DLC has been grown onto VAMWCNT, forming a porous, conductive and stable composite. The electrochemical performance of this DLC:VAMWCNT electrode has been investigated toward detection and analysis of three well‐known molecules, namely paracetamol, codeine and caffeine. A ternary mixture of these analytes was simultaneously determined under optimum experimental conditions using square‐wave voltammetry. Wide linear concentration ranges and the limits of detection of 3.34×10⁻⁷ mol L⁻¹, 1.57×10⁻⁷ mol L⁻¹ and 3.67×10⁻⁷ mol L⁻¹ were obtained for paracetamol, codeine and caffeine, respectively. We conclude that the proposed voltammetric method and the DLC:VAMWCNT electrode comprise a reliable methodology for simultaneous determination of paracetamol, codeine and caffeine in biological matrix samples.     

Efficient Synthesis of a New Podand and Application as a Suitable Carrier for Silver Ion‐Selective Electrode

A new podand of 1,1′‐thia‐bis‐[1‐(chloroethan‐2‐acetamid‐α‐oxy)] naphtol was synthesized and used as a suitable carrier for Ag⁺ PVC membrane electrode. The electrode exhibited linear response with a Nernstian slope of (59.5±0.8 mV/decade) within a wide concentration range of 1.0×10^?7 to 1.5×10^?2 mol L^?1 silver ions. The electrode had a fast response time of <10 s and detection limit of 8.6×10^?8 mol L^?1 with a working pH range from 3.7 to 9.0. The electrode was highly selective for Ag(I) ions over a large number of cations such as alkali, alkaline earth, and heavy metal ions. The proposed sensor has been applied as an indicator electrode for indirect determination of vitamin B₁ in tablets by determination of Cl^? ions in this compound with a standard solution of Ag(NO₃).