多孔碳负载镍纳米颗粒的制备及催化氨硼烷水解制氢

合成了蜂窝状的分级多孔碳,并以多孔碳为载体通过浸渍-化学还原法制备碳载镍(Ni/C)作为催化氨硼烷水解制氢的催化剂。采用XRD、BET、SEM、Raman、TEM等手段对样品进行了表征并研究了Ni/C室温催化性能。结果显示,多孔碳比表面积高达737 m²·g^-1,具有部分石墨化结构;负载的非晶态镍纳米颗粒平均粒径约为10 nm,均匀分布在碳基材。碳载镍对氨硼烷水解反应具有良好的催化活性,镍负载量为30wt%时催化性能最佳,298 K温度下放氢速率达到1 304.67 mL·min^-1·g^-1,活化能为29.1 kJ·mol^-1,并且具备一定的催化稳定性,表明Ni/C可作为一种廉价高效的催化剂应用于催化氨硼烷水解制氢。     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的Pd-Ni/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 mA·cm^-2,并且催化剂催化活性稳定。     

氮掺杂碳层包覆金属钴颗粒与氮掺杂石墨烯纳米复合材料作为高容量锂离子电池负极材料

合成了一种石墨烯基纳米复合材料即：由氮掺杂碳层包覆的金属钴纳米颗粒,充分分散于氮掺杂的石墨烯表面。这种纳米复合材料进一步提高了石墨烯的导电性,增加了石墨烯的储锂容量。该材料被用作锂离子电池负极材料,在性能测试中展现了良好的循环性能,在以100 mA·g^-1的电流密度循环200圈后,放电容量高达950.1 mAh·g^-1,库伦效率约为98%。     

氮掺杂碳层包覆金属钴颗粒与氮掺杂石墨烯纳米复合材料作为高容量锂离子电池负极材料

合成了一种石墨烯基纳米复合材料即：由氮掺杂碳层包覆的金属钴纳米颗粒,充分分散于氮掺杂的石墨烯表面。这种纳米复合材料进一步提高了石墨烯的导电性,增加了石墨烯的储锂容量。该材料被用作锂离子电池负极材料,在性能测试中展现了良好的循环性能,在以100 mA·g^-1的电流密度循环200圈后,放电容量高达950.1 mAh·g^-1,库伦效率约为98%。     

锂离子电池用多孔硅/石墨/碳复合负极材料的研究

在两步高能球磨和酸蚀条件下制得了多孔硅/石墨复合材料，并对其进行碳包覆制成多孔硅/石墨/碳复合材料。通过TEM，SEM等测试手段研究了多孔硅材料的结构。作为锂离子电池负极材料，电化学测试结果表明多孔硅/石墨/碳复合材料相比纳米硅/石墨/碳复合材料有更好的循环稳定性。同时，改变复合体配比、热解碳前驱物、粘结剂种类和用量也会对材料的电化学性能产生较大的影响。其中使用质量分数为10％的LA132粘结剂的电极200次循环以后充电容量保持在649.9 mAh·g^-1，几乎没有衰减。良好的电化学性能主要归因于主活性体-多孔硅颗粒中的纳米孔隙很好地抑制了嵌锂过程中自身的体积膨胀，而且亚微米石墨颗粒和碳的复合也减轻了电极材料的体积效应并改善了其导电性。     

碳包覆纳米金属颗粒的合成研究进展

碳包覆纳米金属颗粒是继富勒烯和碳纳米管之后的又一新型纳米碳材料,在许多领域具有广泛应用前景。本文综述了碳包覆纳米金属颗粒的合成方法,包括：电弧放电法、化学气相沉积法、热解法、液相浸渍炭化法和炭凝胶爆炸法等,简述了形成机理,总结了各自的优缺点,并指出将来的发展方向。     

锂离子电池Si@void@C复合材料的制备及其电化学性能

以纳米Si颗粒为核心,正硅酸四乙酯（TEOS）为SiO₂源,采用Stober法在Si表面包覆一层SiO₂,再以多巴胺为碳源,通过碳化处理将SiO₂表面的聚多巴胺层转化成碳层。最后,用HF刻蚀SiO₂并留下空隙,得到Si@void@C复合纳米颗粒。利用X射线衍射、扫描电镜、透射电镜和恒流充放电测试对材料的物相、微观形貌和电化学性能进行表征。结果表明,在0.1 A·g^-1电流密度下,Si@void@C负极材料充放电循环100次后充电比容量仍然有1 319.5 mAh·g^-1,容量保持率为78.4%,表现出优异的电化学性能。     

Ni@C/HDPE复合材料的制备及其正温度系数性能研究

采用还原气氛喷雾燃烧法制备了具有核壳结构Ni@C纳米复合颗粒,并与HDPE共混挤出制备了聚合物基PTC导电复合材料,并且对其结构和性能进行了表征.结果表明,所制备的Ni@C复合纳米颗粒具有典型的核壳结构,其中,金属镍的核的粒径为30~50 nm,碳包覆壳层的厚度约为2.9 nm,热重分析结果表明Ni@C复合纳米颗粒的含碳量为3.4%,碳包覆层的存在阻止了金属镍颗粒的团聚;对Ni@C/HDPE复合材料的断面SEM和切片TEM分析结果表明复合颗粒在HDPE基体中分散性良好,复合材料的渗流阈值为10wt%,PTC强度为8个数量级.     

富氮掺杂碳空心纳米笼协同钴镍硫化物提升超级电容器性能

采用简单的热解-硫化两步法成功制备了一种新型的富氮掺杂碳空心纳米笼(NC)负载双元金属硫化物纳米颗粒(CoNi_xS_y)的复合材料 CoNi_xS_y/NC。该策略以丁二酮肟镍为镍源,增加了活性位点,同时前驱体 ZIF-8@Ni-ZIF-67的核壳结构为空心碳纳米笼的构建提供了可能性。这种独特的负载多金属硫化物纳米颗粒的中空结构使CoNi_xS_y/NC作为电极材料时具有更多的活性位点、更高的导电性和结构稳定性,从而使其具有较高的比容量(1 A·g^-1时比容量为629.2 F·g^-1),优异的循环稳定性(1 A·g^-1下1 000次循环测试后容量保持率为93.4%)。当将其进一步组装成对称超级电容器后,在1 A·g^-1下可提供207.2 F·g^-1的比电容,1 000圈循环稳定后的容量保持率为85.36%。     

硅镍纳米颗粒的氢电弧等离子体制备及电化学性能研究

采用氢电弧等离子体方法成功地合成了硅镍合金纳米颗粒， 分别用透射电子显微镜(TEM)、X射线衍射(XRD)和能谱分析(EDS)的方法对其形貌、晶体结构和元素化学成分进行了表征，结果显示得到的纳米颗粒由Si和Si₂Ni两相组成。电化学测量的结果表明，在锂嵌入硅镍纳米颗粒的过程中，硅充当活性中心，形成了非晶态的Li_xSi合金，并且在以后的循环中一直保持非晶状态，而其中的Si₂Ni作为惰性成分，不与Li反应，而是充当缓冲基体及导电剂的作用。硅镍合金纳米颗粒的可逆容量达1 304 mAh·g^-1，并且循环性能明显优于纯硅材料。硅镍合金纳米颗粒与石墨组成的复合材料，不但具有较高的可逆比容量，而且有较好的循环稳定性，20次循环后比容量仍为518 mAh·g^-1，容量保持率为86％,是有希望的锂离子电池负极材料。     

均三嗪衍生物应用于Fe3+和Cu2+的选择性识别研究

合成了2,4-二甲基-6-(4’-N,N-二甲氨基苯乙烯基)-1,3,5-均三嗪(1)和2-苯乙烯基-4,6-二甲基-1,3,5-均三嗪(2)两种化合物,并对其进行了1H NMR,MS,元素分析等表征.采用吸收光谱法研究了金属离子与化合物间的相互作用,结果显示:化合物1对Fe3+和Cu2+表现出高选择性光谱响应,其最大吸收波长由393 nm分别红移至525 nm和513 nm,溶液颜色由黄色变为粉红色.化合物1与Fe3+结合形成1∶1型配合物,其结合常数为1.8×104L mol-1;与Cu2+结合形成2∶1型配合物,其结合常数为2.6×1010L mol-1.化合物2仅对Fe3+呈现显著的光谱变化,其最大吸收波长由304nm红移至357 nm,而Cu2+的加入未引起光谱明显变化,2与Fe3+亦形成1∶1型配合物,结合常数为1.0×105L mol-1.结果表明Fe3+可能与化合物1和2中三嗪N配位,而Cu2+与化合物1中甲氨基中的N配位.同时考察了其它金属离子如Li+,K+,Mg2+,Ca2+,Co3+,Ni2+,Ag+,Cd2+,Hg2+和Zn2+等离子对化合物1和2吸收光谱的影响,结果显示两者光谱均无明显变化,据此提出了高选择性Fe3+,Cu2+的识别体系.     

<113>_(c)晶带轴下Ba(B′_(1/3)B″_(2/3))O_(3)钙钛矿B位1∶2有序结构的透射电镜表征

提出了通过透射电子显微镜表征Ba(B′_(1/3)B″_(2/3))O 3钙钛矿(B′=Zn^(2+)、Mg^(2+)、Co^(2+)或Ni^(2+),B″=Ta^(5+)或Nb^(5+))B位1∶2有序结构时可采用的一个新的晶带轴(<113>c),并首次研究了<113>c带轴下有序钙钛矿的原子架构.在<113>c晶带轴下,选区电子衍射(SAED)中的±1/3{112}型超晶格斑点揭示了钙钛矿的1∶2有序结构.对应的高分辨电子衍射(HRTEM)图像清楚地显示了有序畴的大小和原子结构.高分辨图像中的成分衬度与原子结构非常匹配,进一步证实了沿<113>c带轴下的1∶2有序结构.     

浸渍硅胶薄层色谱板分离钴和镍及数字图像分析法定量(英文)

Thin layer chromatography(TLC) of cobalt and nickel has been performed on silica gel layers induced with alkali mediated cellulose extract.A novel combination of 10% aqueous solutions of Tween-20 and potassium thiocyanate in 1∶1(v/v) was identified as the best mobile phase for the selective separation of Co2+from Ni2+on the impregnated Silica Gel G layers.The chromatographic characteristics of the cations were studied and the limits of detection as well as the limits of quantification for Co2+and Ni2+were determined.The quantitative estimation of the cations was achieved from the digital image analysis of respective chromatograms.The proposed quantitative method was successfully applied with 0-0.50% error for the determination of Co2+from Ni2+in spiked samples of bauxite,soil and rock containing common cations such as Al3+,Fe2+,Ti4+,Zn2+,Mn2+,Cu2+,Cr6+,Mg2+,etc.under the optimized chromatographic conditions.     

Transfer of a quadridentate N2S2 ligand from M2+ (M=Cr,Mn, Fe,Co or Ni) to Cu2+: Unexpected reactivities of bimetallic intermediates

A series of complexes of stoichiometry [MX2(dipyS)] {dipyS = bis(2–picolyl)-1,3–dithiopropane); M=Cr, Mn, Fe, Co, Ni, X=Cl; M=Ni or Cu, X=NO3} and [VOCl(dipyS)]Cl have been prepared and characterised, including the X-ray crystal structure of [Ni(ONO2)2(dipyS)]. The kinetics of the transfer of dipyS from these complexes (M=Cr, Mn, Fe, Co or Ni) to Cu2+, to form [Cu(dipyS)]2+, have been studied in MeOH. For M=Ni, the kinetics are consistent with a mechanism involving rate-limiting dissociation of the initial pyridyl—M bond. Subsequent binding of Cu2+ to the pendant pyridyl-residue (or binding Cl– to the vacant site on M) is followed by the complete transfer of dipyS from M to Cu. For M=Cr, Mn or Co, the same mechanism is believed to operate, but in these cases intermediates in the dipyS transfer to Cu2+ have been detected spectroscopically. Evidence is presented that these intermediates have Cu2+ bound to a pendant pyridyl-group on [MCl2(dipyS)] and that the subsequent complete transfer of dipyS involves rate-limiting dissociation of a M—S bond. For M=Fe, e.p.r. spectroscopy shows that the complex is a dimer in solution. However, the transfer reaction with Cu2+ involves an analogous intermediate to that with M=Cr, Mn or Co, but only at high concentrations of Cu2+. Unexpectedly, the binding of Cu2+ inhibits the transfer of dipyS from Fe to Cu. The electronic factors which give rise to this behaviour are discussed.     

Separation and spectroscopic characterization of new metal chelates of 8-arylazo-6-formyl-7-hydroxy-5-methoxy-2-methyl chromones

Transition metal chelates of the title compounds have been prepared and characterized by elemental analyses, i.r., 1H-n.m.r., electronic spectra, thermogravimetric analysis, conductometric and magnetic measurements. Chelates of general formulae MLjX · nH2O for 1:1 (M:L), where X=OH– or Cl–, j=1 or 2, n=1– 4 and M=VO2+, Cr3+, Mn2+, Fe2+, Co2+, Ni2+, Cu2+ and Zn2+ ions or ML2 for 1:2 (M:L) Ni-(1a), ML2·2H2O where M=Co2+, Ni2+ and Cu2+ or M2LjX·nH2O for 2:1 (M:L) Cr3+, Fe2+, Ni2+ and Cu2+, L=Ligand, have been prepared. I.r. and 1H-n.m.r. spectra indicate that the aldehydic group in position six and the hydroxylic group in position seven are involved in chelation in the 1:1 and 1:2 (M:L) chelates, whereas for 2:1 (M:L) chelates with (1c), the interaction of the metal ion takes place through CHO, OH, CO2H and NN groups. Tetrahedral, octahedral and square planar geometries are proposed for the chelates based on their electronic spectra and magnetic moments.     

Irving-Williams order in the framework of connectivity index ³χv enables simultaneous prediction of stability constants of bivalent transition metal complexes

Logarithms of stability constants, log K? and log β?, of the first transition series metal mono- and bis-complexes with any of four aliphatic amino acids (glycine, alanine, valine and leucine) decrease monotonously with third order valence connectivity index, 3χv, from Cu2+ to Mn2+. While stability of the complexes with the same metal is linearly dependent on 3χv, stability constants of Mn2+, Fe2+, Co2+, and Ni2+complexes with the same ligand show a quadratic dependence on 3χv. As Cu2+ complexes deviate significantly from quadratic functions, models for the simultaneous estimation of the stability constants, yielding r = 0.999 (S.E. = 0.05) and r = 0.998 (S.E. = 0.11), for log K? and log β?, respectively, were developed only for Mn2+, Fe2+, Co2+, and Ni2+ complexes with amino acids.     

双金属氰化络合物及其催化的聚合反应

本文综述了双金属氰化络合物及其催化的环氧化物参与的聚合反应研究。双金属氰化络合物是由其内界金属M^Ⅱ通过氰基与外界金属M^Ⅰ连接形成的含 M^Ⅱ-C≡N-M^Ⅰ 桥键的三维网络状无机高分子(M^Ⅰ一般为Zn²⁺、Fe²⁺、Co²⁺和Ni²⁺等二价金属离子,M^Ⅱ一般为Fe²⁺、Fe³⁺、Co²⁺、Co³⁺和Ni²⁺等过渡金属离子)。外界金属M^Ⅰ一般被认为是催化反应的活性中心金属。该类催化剂早期被用于催化环氧化物开环聚合,并逐步发展成为合成中高分子量、低不饱和度聚醚多元醇的极高效催化剂。近年来该类催化剂被用来催化环氧化物/环状酸酐共聚、环氧化物/CX₂(X≡O,S)共聚和环氧化物/环状酸酐/CO₂三元共聚反应合成聚酯、聚碳酸酯、聚(醚-碳酸酯)、聚硫代碳酸酯和聚(碳酸酯-酯)等具有生物降解性的聚合物。尤其对氧化环己烯(CHO)与CO₂(或酸酐)共聚,锌-钴双金属氰化络合物表现出了极高的催化活性和选择性。结合本研究组十多年的研究结果,本文讨论了双金属氰化络合物催化活性中心的可能结构和催化机理,提出了双金属氰化络合物催化聚合的共性难题和解决这些问题的方向。     

Citrate, in collaboration with a guanidinium ion, as a generator of cubane-like complexes with a range of metal cations: synthesis, structures, and magnetic properties of [C(NH2)3]8[(M(II))4(cit)4].8H2O (M = Mg, Mn, Fe, Co, Ni, and Zn; cit = Citrate)

Aqueous reaction mixtures containing citric acid, guanidinium carbonate, and a range of metal cations (Mg2+, Mn2+, Fe2+, Co2+, Ni2+, and Zn2+) at room temperature give crystalline products of composition [C(NH2)3]8[(M(II))4(cit)4].8H2O (cit = citrate). In all cases, the crystals are suitable for single-crystal X-ray diffraction studies, which reveal that the compounds are isostructural (space group P4(2)/n; a approximately 16.2 A, and c approximately 11.5 A). As was intended, cubane-like [M4(cit)4]8- complex anions are present. The individual citrate units are chiral, but each cubane unit contains two of one hand and two of the other, related around an S4 axis. The cubane units are involved in no less than 40 H-bonding interactions with guanidinium cations and lattice water molecules. Detailed susceptibility and magnetization studies show that the intracluster magnetic coupling within the Mn(II), Fe(II), Co(II), and Ni(II) cubanes is very weak in all cases with J values of -0.82, -0.43, and -0.09 cm(-1) for the Mn, Fe, and Co species, respectively. A two-J model gave the best agreement with the susceptibility and high-field magnetization data for the Ni(II) case, over the whole temperature range studied, and the sign of the parameters, J12 = -0.3 cm(-1) and J13 = +2.97 cm(-1), correlated with the two Ni-(mu3-O)-Ni angles observed in the cluster structure. All members of the 3d-block [M4(cit)4]8- family have spin ground states, ST, of zero, with the higher ST levels just a few reciprocal centimeters away in energy.     

荧光法研究不同离子对溶菌酶的猝灭作用

本文利用荧光法,在生理pH(7.37±0.02)条件下,分别测定了Fe3+、Cu2+、Ni2+、Co2+、NO2-、I-、盐酸胍对溶菌酶的猝灭作用。用荧光猝灭法求得不同猝灭剂对溶菌酶的猝灭常数KSV、生成常数KA、离解常数KD、结合位点数n和热力学参数ΔrGmΘ、ΔrHmΘ、ΔrSmΘ。据此判断了体系中猝灭剂对溶菌酶的作用机理。I-对溶菌酶的猝灭是动态猝灭,而Fe3+、Cu2+、NO2-Ni2+、Co2+及盐酸胍对溶菌酶是静态猝灭;Fe3+、Cu2+、Ni2+、Co2+与溶菌酶之间的作用力主要为氢键、范德华力;NO2-与溶菌酶间的作用力主要为静电作用力;I-与溶菌酶之间的作用力主要为疏水作用力。在分子水平上理解这些外源性化合物与溶菌酶的作用机理具有及其重要意义。     

过渡元素杂多钨硅酸盐氧化还原性质的研究

本文通过极谱和循环伏安法,结合紫外光谱和X射线光电子能谱,研究了过渡元素钨硅杂多酸盐Kn[SiM(H2O)W11O39](M=Mn^2^+,Fe^3^+,Co^2^+,Ni^2^+,Zn^2^+,Cd^2^+)在溶液中的氧化还原性质,提出了它们的还原机理.杂多阴离子的极谱半波还原电位E1/2的顺序为Ni^2^+>Co^2^+>Zn^2^+>Fe^2^+>Mn^2^+,发现杂多阴离子的E1/2与其组分中的过渡元素的电负性X和过渡金属离子与水合电子反应速率常数的对数logke-分别有线性关系,讨论了过渡元素对杂多阴离子氧化还原性的影响.