多次交替浸渍法构筑簇状ZnO的PAN复合纳米纤维膜及其光催化性能

以聚丙烯腈(PAN)与氯化锌(ZnCl2)作为前驱物,采用静电纺丝工艺制备PAN/ZnCl_2复合纳米纤维膜,分别采用多次冷热交替浸渍法和单次冷热静置浸渍法得到簇状PAN/ZnO-1和PAN/ZnO-2复合纳米纤维膜。利用扫描电镜(SEM)、傅里叶红外光谱(FT-IR)、X射线衍射(XRD)、X射线能量色散光谱(XPS)和热重分析仪(TG)对复合纳米纤维膜的表面形貌和微结构进行了表征,并以亚甲基蓝(MB)为污染物模型,评价其光催化降解性能。结果表明:经冷热交替浸渍后,纳米ZnO粒子均匀地附着在PAN纤维表面,尤其在PAN/ZnO-1复合纳米纤维膜表面还出现了花状ZnO粒子;相比单次冷热静置浸渍法处理的PAN/ZnO-2复合纳米纤维膜,经多次冷热交替浸渍的PAN/ZnO-1复合纳米纤维膜循环使用3次后对MB的降解率仍可达到90%以上,具有更好的光催化活性和循环使用性能。同时,MB溶液的初始质量浓度、催化剂用量和染料溶液的pH等因素对样品的的光催化降解率有一定影响。     

低压近场静电纺丝ZnO/PVDF复合微米纤维阵列的制备及压力传感性

利用低压近场静电纺丝技术制备了ZnO/PVDF(聚二偏氟乙烯)微米纤维平行阵列, 通过光学显微镜、扫描电子显微镜(SEM)和X射线能量色散光谱(EDS)对ZnO/PVDF微米纤维进行了表征. 该复合纤维的平均直径约为40 μm. EDS分析测试证明ZnO纳米颗粒已经掺杂进入了平行微米纤维中. 压电性能和电学性能测试结果表明, ZnO/PVDF微米纤维阵列的压电性能增强. 研究结果表明, 近场电纺丝ZnO/PVDF复合微米纤维阵列在压电型压力传感器和纳米发电机领域具有潜在的应用价值.     

低压近场静电纺丝ZnO/PVDF复合微米纤维阵列的制备及压力传感性（英文）

利用低压近场静电纺丝技术制备了ZnO/PVDF(聚二偏氟乙烯)微米纤维平行阵列,通过光学显微镜、扫描电子显微镜(SEM)和X射线能量色散光谱(EDS)对ZnO/PVDF微米纤维进行了表征.该复合纤维的平均直径约为40μm.EDS分析测试证明ZnO纳米颗粒已经掺杂进入了平行微米纤维中.压电性能和电学性能测试结果表明,ZnO/PVDF微米纤维阵列的压电性能增强.研究结果表明,近场电纺丝ZnO/PVDF复合微米纤维阵列在压电型压力传感器和纳米发电机领域具有潜在的应用价值.     

静电纺丝法制备聚丙烯腈/聚苯胺复合纳米纤维及其表征

利用静电纺丝技术,以聚丙烯腈(PAN)和苯胺(ANI)为前驱物,用过硫酸胺(APS)溶液在低温下缓慢氧化聚合,制备了PAN/PANI复合纳米纤维,直径约500 nm.通过扫描电子显微镜(SEM)、红外光谱(FTIR)、X射线衍射(XRD)和激光拉曼(RAMAN)光谱仪等测试手段对材料的形貌和结构进行了表征.探讨了材料制备过程中影响纤维形貌、尺寸、均匀度的因素和PANI含量对复合纤维导电性能的影响,结果表明,PAN浓度、ANI的加入量和电压是影响纤维特性的主要因素;PANI在PAN基体中呈纳米尺寸分布,复合纳米纤维具有良好的导电性能,导电率可达10-2S/cm.     

导电玻璃负载Fe_2O_3/ZnO复合光电极的制备及光电催化性能

以聚乙烯吡咯烷酮(PVP)为纤维骨架,乙醇为溶剂,乙酸锌[Zn(CH_3COO)_2·2H_2O]和三乙酰丙酮铁(C_(15)H_(21)O_6Fe)为原料,利用静电纺丝技术结合溶胶-凝胶法制备前驱体纤维,经焙烧后得到不同摩尔比的FTO导电玻璃负载Fe_2O_3/ZnO复合光电极(Fe_2O_3/ZnO/FTO).利用热重-差热分析仪(TG-DTA)、X射线衍射仪(XRD)、扫描电子显微镜(SEM)和X射线光电子能谱仪(XPS)等对材料进行了表征,以亚甲基蓝(MB)为目标降解物,探讨了复合材料的光电催化活性.结果表明,Fe_2O_3与ZnO的复合能够有效构建p-n异质结,利于光生电子和空穴的分离,其光电催化性能较纯ZnO/FTO和Fe_2O_3/FTO均有明显提高;不同n(Fe)/n(Zn)的复合光电极表现出了不同的光电催化活性,在相同催化时间内,当n(Fe)/n(Zn)=1∶1时,Fe_2O_3/ZnO/FTO对MB催化活性最佳,MB的降解率达到97%.     

ZnO纳米纤维的静电纺丝及其光催化性能的研究

以聚乙烯醇溶液为络合剂与醋酸锌反应制得前驱体溶液,采用静电纺丝法制备PVA/Zn(Ac)2复合纳米纤维,经过高温煅烧得到直径为100 nm的ZnO纳米纤维,采用差热-热重分析、红外光谱分析、X射线粉末衍射分析及扫描电镜等手段对其进行了表征.光催化降解酸性品红溶液的实验结果表明,太阳光照65 min使质量浓度为45 mg/L酸性品红水溶液的脱色率达93%;另外,重复使用ZnO纳米纤维4次之后,其光催化降解率仍能达到70%以上.这充分说明ZnO纳米纤维具有良好的光催化性能.     

同轴静电纺丝法制备ZnO/Ag2O纳米纤维材料及其光电催化性能研究

以醋酸锌和乙酰丙酮银为前驱体, 通过同轴静电纺丝和热处理过程在氟掺杂氧化锡(FTO)导电玻璃上制备了ZnO/Ag₂O同轴纳米纤维. 采用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 拉曼光谱和紫外-可见漫反射光谱(UV-Vis DRS)等手段对材料进行了表征. 以氙灯模拟可见光光源, 亚甲基蓝为目标降解物, 考察了所制备纳米纤维的光电催化活性. 结果表明, 同轴ZnO/Ag₂O纳米纤维具有壳核类似结构(ZnO为壳, Ag₂O为核), Ag₂O与ZnO形成的异质结和杂质能级降低了ZnO的带隙能, 提高了对可见光的利用率. 在可见光下, 与纯ZnO相比, ZnO/Ag₂O具有很强的光电催化能力, 并且Ag₂O的量对同轴纤维光电催化活性影响很大, 在同样光电催化条件下, ZnO/Ag₂O-7同轴纳米纤维的光电催化效果最好, 亚甲基蓝降解率达93%, 动力学常数最大为1.13×10 ^-2 min ^-1.     

结晶紫在亚微米棒状ZnO表面增强拉曼光谱的研究

通过湿化学法在70℃低温条件下,制备了亚微米棒状ZnO。利用紫外可见吸收光谱(UV-Vis),扫描电镜(SEM),X射线粉末衍射(XRD)以及拉曼光谱对棒状ZnO进行了表征。采用密度泛函(DFT/B3LYP)方法,以6-311G*为基组研究了结晶紫(CV)的理论平衡构型,同时以CV作为探针分子,检测了亚微米棒状ZnO的表面增强拉曼(SERS)活性。结果表明:亚微米棒状ZnO为六方纤锌矿结构,具有很高纯度和结晶度。CV在ZnO表面的拉曼增强因子可达1.2×102,其增强机理主要来源于化学增强。     

Ag/ZnO纳米纤维的制备及光催化性能

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维, 然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面. 利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 能量色散X射线光谱(EDX)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征. SEM结果表明, 直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构. 以常见的有机污染物甲基橙、 亚甲基蓝和罗丹明B等为降解底物, 对Ag/ZnO纳米纤维的光催化性能进行了表征. 结果表明, 负载银纳米颗粒后, 复合催化剂的光催化性能明显提高.     

Ag/ZnO纳米纤维的制备及光催化性能（英文）

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维,然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、能量色散X射线光谱(EDX)、扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征.SEM结果表明,直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构.以常见的有机污染物甲基橙、亚甲基蓝和罗丹明B等为降解底物,对Ag/ZnO纳米纤维的光催化性能进行了表征.结果表明,负载银纳米颗粒后,复合催化剂的光催化性能明显提高.     

Synthesis and Optical Properties of ZnO Nanoparticles in Submicron PS Hollow Reactors

ZnO nanoparticles were first encapsulated in submicron PS hollow microspheres through two-step swelling process of core-shell structured PMMA/PS (PMMA: polymethyl methao-rylate) microspheres in acid-alkali solution, and the ZnO precursors, i.e. the ethanol solu-tions of (CH₃COO)₂Zn and LiOH. The transmission electron microscope, X-ray diffraction, and thermogravimetric analysis results show that the feeding order of ethanol solutions of (CH₃COO)₂Zn and LiOH in the second swelling step has great influence on the loading efficiency and the size of ZnO nanoparticles, but little on their crystal form. The photolumi-nescence and UV-Vis absorption behavior of ZnO/PS microspheres show that the PS shell can effectively avoid the fluorescence quenching effect.     

SiO2/ZnO复合纳米粒子的制备及表征

采用双注控制沉积法(Controlled Double-Jet Precipitation,CDJP)将反应物添加到含有SiO₂的溶液中,通过直接的表面反应来制备单分散的SiO₂/ZnO复合纳米粒子,并对其进行了表征。透射电镜(TEM)观察表明,SiO₂表面有一层ZnO纳米颗粒或薄层。对复合纳米粒子SiO₂/ZnO进行X射线衍射(XRD)分析,复合颗粒的衍射峰与单独的氧化锌的衍射峰完全一致。能量弥散X射线法(EDX)分析表明,复合颗粒中含有Zn、Si、O元素。荧光光谱表明有ZnO的吸收峰。     

Preparation of porous ultrafine polyacrylonitrile (PAN) fibers by electrospinning

A facile method for the preparation of porous ultrafine nanofibers was demonstrated. The PAN/NaHCO₃ composite nanofibers were electrospun, and then NaHCO₃ was removed by a selective dissolution and reaction with the solution of hydrochloric acid (10 wt%). The obtained PAN fibers showed highly porous surfaces after the extraction of NaHCO₃. The structure and properties of ultrafine PAN nanofibers were characterized by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), and thermogravimetry (TG). The results indicated that NaHCO₃ could be introduced into the PAN solution and successfully electrospun. CO₂ is released and pores are formed on the fibers. The morphology image of the fibers was detected by scanning electron microscope (SEM) and showed that many pores aligned the nanofibers. Copyright © 2008 John Wiley & Sons, Ltd.     

Nanosized anatase titanium dioxide loaded porous carbon nanofiber webs as anode materials for lithium-ion batteries

Nanosized anatase titanium dioxide loaded porous carbon nanofibers (TiO₂/PCNFs) were prepared from electrospun TiO(OAc)₂/PAN/PMMA composite precursor fibers with different amount of PMMA porogen, which were sequentially heat-treated in different environments. Electrochemical measurement results show that these as-prepared TiO₂/PCNFs present higher cyclic reversible capacity than the TiO₂/CNFs counterpart (without PMMA porogen in its precursor fibers). Among the as-prepared TiO₂/PCNFs samples, the representative TiO₂/PCNFs (the mass ratio of PAN to PMMA is 3:1) exhibits the best high-rate performance with a high stable capacity retention about 200 mAhg^{− 1} at a current density as high as 800 mAg^{− 1}. This novel TiO₂/PCNFs composite material opens up a promising application in high-power lithium-ion batteries.     

Synthesis and characterization of polycrystalline ZnO/HZSM-5 nanocomposites

Polycrystalline ZnO/HZSM-5 nanocomposites were synthesized by the impregnation method using a home prepared HZSM-5 zeolite as porous support and Zn(C₅H₇O₂)₂ or Zn(NO₃)₂ as zinc precursors. As-prepared samples were characterized by ICP, XRD, SEM (EDS), TEM (SAED), BET and DRS techniques. A small amount of sub-nanometeric ZnO clusters were introduced into the channels of HZSM-5 zeolite. These ZnO clusters exhibited absorption band onset at about 280 nm, different from ZnO particles at about 370 nm. The significant blue shift possesses high quantum size effect in sub-nanometeric ZnO clusters. SAED and TEM images revealed that the ZnO nanoparticles, supported on the surface of HZSM-5 zeolite, were identified as polycrystalline structure with the particle size of about 20-25 nm. XRD results provided evidence of the strong host-guest interactions between HZSM-5 framework and ZnO structure. The samples prepared by Zn(C₅H₇O₂)₂ were more porous and smaller than those prepared from the Zn(NO₃)₂. This was confirmed by SEM and XRD results.     

Facile Fabrication of Porous ZnS and ZnO Films by Coaxial Electrospinning for Highly Efficient Photodegradation of Organic Dyes

Porous ZnS and ZnO nano‐crystal films were fabricated via a three‐step procedure. First, Zn(CH₃COO)₂/Silk Fibroin nanofiber mats were prepared by coaxial electrospinning. Second, Zn(CH₃COO)₂/Silk Fibroin mats were immersed in NaS solution to react with S²⁻ to obtain ZnS/Silk Fibroin nanofiber mats. Finally, ZnO porous films were prepared by calcination of ZnS/Silk Fibroin composite mat at 600°C in air atmosphere. When ZnS/Silk Fibroin mats were calcinated in nitrogen, ZnS/Carbon composite mats were obtained accordingly. The resulting porous films were fully characterized. The ZnO porous films were the aggregation of ZnO nano‐crystal with hexagonal wurtzite structure. The seize of ZnO was estimated in the range of 10–20 nm. Both of the ZnS and ZnO nano‐crystal films exhibited high photocatalytic activities for the photodegradation of Methylene blue and Rhodamine B. It was also found that ZnO porous films are better than ZnS/Carbon nanofiber mats. In addition, photocatalysis of a real wastewater sample from a printing and dyeing company was conducted. The ZnO porous films exhibited excellent performance to treat the real samples. Moreover, the porous ZnO nano‐crystal photocatalyst could easily be recycled without notable loss of catalysis ability.     

Determination of ZnO(0001) surface termination by x‐ray photoelectron spectroscopy at photoemission angles of 0° and 70°

We present an XPS method to determine the termination of the ZnO(0001) surface. By measuring O 1s and Zn 2p_3/2 core‐level x‐ray photoelectron spectra at photoemission angles of 0° and 70° and comparing the intensity ratio (I_O1s/I_Zn2p3)_θ=0/(I_O1s/I_Zn2p3)_θ=70, the Zn and O termination can be distinguished. Calculations show that these two terminations have intensity ratios differing by ～17%. This difference is not affected by a contamination layer provided that the contamination layer thickness is the same for these two differently terminated surfaces. Although this determination method prefers a clean ZnO(0001) surface (in situ measurement), it seems also feasible for surfaces with known contamination layer thickness (ex situ measurement). We have measured ex situ ZnO(0001)‐Zn, ZnO(000&1macr;)‐O single crystals and an epitaxial ZnO film deposited on Al₂O₃(0001). The measured intensity ratios of the first two samples agree with the calculated values for a 0.2 and 0.26 nm contamination layer, respectively. The intensity ratio and the O 1s contamination component intensity of the epitaxial ZnO film are close to those of the ZnO(0001)‐Zn single crystal thus pointing at Zn termination of the film. Copyright © 2004 John Wiley & Sons, Ltd.     

Removal of 63Ni and 57Co from aqueous solution using antimony doped tin dioxide–polyacrylonitrile (Sb doped SnO2–PAN) composite ion-exchangers

Tin dioxide and its antimony doped counterpart were synthesized using traditional sol–gel procedure. The metal oxides were then turned into composites by mixing them with polyacrylonitrile (PAN) and composite spheres ready for use in traditional column applications were obtained. The characterization of materials was investigated by X-ray diffraction, scanning electron microscopy–energy dispersive X-ray, surface area, point of zero charge and thermal analyses. Static batch experiments showed that the antimony doped tin dioxide–PAN (Sb doped SnO₂–PAN) is an effective material for nickel removal and the composite maintains its good metal uptake properties in dynamic column conditions. The composite showed a high nickel uptake capacity of 9 mmol/g in 0.1 M NaNO₃ solution. It was observed that the ion exchange kinetics of antimony doped tin dioxide (Sb doped SnO₂) was remarkably fast for ⁵⁷Co and ⁶³Ni ions but turning the material into PAN composite significantly decreased the materials kinetic properties.     

ZnO修饰提升花状BiOBr的可见光催化降解罗丹明B性能

以Bi(NO₃)₃·5H₂O、Zn(CH₃COO)₂·2H₂O和NaBr为前驱体,采用简单溶剂热法制备BiOBr/ZnO三维花状微纳米复合材料。采用X射线衍射、扫描电子显微镜、X射线光子能谱、N₂吸附-脱附、光致发光和电子顺磁共振等分析技术对其理化性质进行了表征。通过可见光催化降解罗丹明B(RhB)的实验测试了复合材料的光催化性能。结果表明ZnO含量为5%的BiOBr/ZnO光催化活性最优,RhB降解率在50 min后达到98.3%,其降解速率常数是纯ZnO和BiOBr的6.3倍和3.4倍,并且具有较高的稳定性。复合材料光催化性能增强的可能原因为ZnO的引入增强了可见光的吸收和光生载流子的电荷分离效率。     

Photodegradation of Rhodamine B on Sulfur Doped ZnO/TiO2 Nanocomposite Photocatalyst under Visible-light Irradiation

Sulfur doped ZnO/TiO₂ nanocomposite photocatalysts were synthesized by a facile sol‐gel method. The structure and properties of catalysts were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), UV‐vis diffusive reflectance spectroscopy (DRS) and N₂ desorption‐adsorption isotherm. The XRD study showed that TiO₂ was anatase phase and there was no obvious difference in crystal composition of various S‐ZnO/TiO₂. The XPS study showed that the Zn element exists as ZnO and S atoms form SO^2?₄. The prepared samples had mesoporosity revealed by N₂ desorption‐adsorption isotherm result. The degradation of Rhodamine B dye under visible light irradiation was chosen as probe reaction to evaluate the photocatalytic activity of the ZnO/TiO₂ nanocomposite. The commercial TiO₂ photocatalyst (Degussa P25) was taken as standard photocatalyst to contrast the prepared different photocatalyst in current work. The improvement of the photocatalytic activity of S‐ZnO/TiO₂ composite photocatalyst can be attributed to the suitable energetic positions between ZnO and TiO₂, the acidity site caused by sulfur doping and the enlargement of the specific area. S‐3.0ZnO/TiO₂ exhibited the highest photocatalytic activity under visible light irradiation after Zn amount was optimized, which was 2.6 times higher than P25.