Gallic acid‐loaded electrospun cellulose acetate nanofibers as potential wound dressing materials

Gallic acid (GA)–loaded cellulose acetate (CA) nanofiber mats with 10 to 40 wt.% GA contents (based on the weight of CA) were fabricated by electrospinning. The effects of GA contents and applied potential on the morphology and the average diameters of fibers were studied. The electrospun fiber mats containing 20 and 40 wt.% GA were investigated for their potential use as carrier of GA in wound dressing application. The GA‐loaded CA films were prepared by solvent casting technique for use in comparative studies. Determination of the release characteristics of GA from the GA‐loaded fiber mats and films was carried out by the total immersion and the transdermal diffusion through a pig skin method in acetate buffer solution (pH 5.5) or normal saline (pH 7.0) at either 32 or 37°C, respectively. In the total immersion method, the maximum amounts of the GA released from the fiber mats containing 20 and 40 wt.% GA in the acetate buffer were approximately 97% and 71% (based on the weight of initial GA), while those of the GA released into the normal saline were approximately 96% and 81%, respectively. Lower values were observed in the experiments of the transdermal diffusion through a pig skin method. The corresponding GA‐loaded CA films showed the lower amounts of GA released into media. The as‐loaded and the as‐released GA remained its antioxidant activity as investigated by 1,1‐diphenyl‐2‐picrylhydrazyl (DPPH) assay. Lastly, the GA‐loaded CA fiber mats exhibited antibacterial activity against Staphylococcus aureus, which showed the potential for use as wound dressing materials.     

Deposition of silver nanoparticles on cellulosic fibers via stabilization of carboxymethyl groups

The stabilizing role of carboxymethyl groups on the conformal deposition of Ag NPs over cellulosic fibers was elucidated while developing a method for the deposition of silver nanoparticles (NPs) on cellulose acetate (CA), cellulose and partially carboxymethylated cellulose (CMC) electrospun fibers. CMC fibers were prepared through judicious anionization of deacetylated cellulose acetate fibers. Ag NPs were chemically reduced from silver nitrate using sodium borohydride and further stabilized using citrate. Ag NPs were directly deposited onto CA, cellulose and CMC electrospun fibers at pH conditions ranging from 2.5 to 9.0. The resulting composites of Ag/fiber were characterized by field emission scanning electron microscopy (FESEM) and energy-dispersive X-ray spectroscopy (EDX). The results revealed that the amount of Ag agglomerates and NPs deposited on CMC fibers was higher than that deposited on cellulose fibers at similar pH conditions, and that barely any Ag agglomerates or NPs were deposited on the CA fibers. These results implied that functional groups on the cellulose backbone played two important roles in the deposition of NPs as follows: (1) Hydrogen bonding was the main driving force for agglomeration of NPs when the medium pH was below 4.4, which corresponds to the pKa of carboxylic acid groups; (2) Carboxymethyl groups could replace citrate groups as stabilizers allowing the fabrication of a uniform and evenly distributed Ag NPs layer over CMC fibers at higher pH values. This report also highlights the importance of the substrate’s surface charge and that of the pH of the medium used, on the deposition of NPs. The composite of Ag NPs on CMC electrospun fibers appears to be a promising candidate for wound dressing applications due to its superior antibacterial properties originated by the uniform and even distribution of Ag NPs on the surface of the fibers and the wound healing aptness of the CMC fibers.     

Characterization and cytocompatibility of polydopamine on MAO‐HA coating supported on Mg‐Zn‐Ca alloy

Magnesium has been suggested as a potential biodegradable metal for the usage as orthopaedic implants. However, high degradation rate in physiological environment remains the biggest challenge, impeding wide clinical application of magnesium‐based biomaterials. In order to reduce its degradation rate and improve the biocompatibility, micro‐arc oxidation coating doped with HA particles (MAO‐HA) was applied as the inner coating, and polydopamine (PDA) film was synthesized by dopamine self‐polymerization as the outer coating. The microstructure evolution of the coating was characterized using scanning electron microscopy (SEM), atomic force microscope (AFM), X‐ray diffraction analyses (XRD), Fourier transform infrared spectroscopy (FT‐IR), and X‐ray photoelectron spectroscopy (XPS). The results showed that PDA film had covered the entire surface of MAO‐HA coating and the pore size of MAO‐HA coating decreased. The root mean square (RMS) roughness of PDA/MAO‐HA coatings was approximately 106.46 nm, which was closer to the optimum surface roughness for cellular attachment as compared with MAO‐HA coatings. Contact angle measurement indicated that the surface wettability had been transformed from hydrophobic to hydrophilic due to the introduction of PDA. The PDA/MAO‐HA coatings exhibited better corrosion resistance in vitro, with the self‐corrosion potential increasing by 150 mV and the corrosion current density decreasing from 2.09 × 10^?5 A/cm ² to 1.46 × 10^?6 A/cm ² . In hydrogen evolution tests, the corrosion rates of the samples coated with PDA/MAO‐HA and MAO‐HA were 4.40 and 5.95 mm/y, respectively. MTS assay test and cell‐surface interactions experiment demonstrated that PDA/MAO‐HA coatings exhibited good cellular compatibility and could promote the adhesion and proliferation of MC3T3‐E1 cells.     

Properties of electrospun PVDF/PMMA/CA membrane as lithium based battery separator

Poly vinylidene fluoride:poly methyl methacrylate:cellulose acetate (CA) at ratios of 100:0:0, 90:10:0, 90:5:5 and 90:0:10 respectively, were successfully electrospun. These membranes were mixed to form a 12 wt% solution prepared with volume ratio 7:3 of DMAc:acetone solvents. These membranes were then analyzed using differential scanning calorimetry, scanning electron microscopy, FTIR, WAXD, pore size, porosity% and electrolyte uptake (EU)%. It was observed that the best absorption results were obtained in the presence of CA. The electrospun membrane at ratio of 90:0:10 was observed with the highest porosity of 99.1 % and EU at 323 %. It also had a 43.6 % crystallinity and a 162 °C melting temperature. It was then concluded that addition of CA improved the separator properties.     

A Monolithic Hybrid Cellulose‐2.5‐Acetate/Polymer Bioreactor for Biocatalysis under Continuous Liquid–Liquid Conditions Using a Supported Ionic Liquid Phase

Mesoporous monolithic hybrid cellulose‐2.5‐acetate (CA)/polymer supports were prepared under solvent‐induced phase separation conditions using cellulose‐2.5‐acetate microbeads 8–14 μm in diameter, 1,1,1‐tris(hydroxymethyl)propane and 4,4′‐methylenebis(phenylisocyanate) as monomers as well as THF and n‐heptane as porogenic solvents. 4‐(Dimethylamino)pyridine and dibutyltin dilaurate (DBTDL), respectively, were used as catalysts. Monolithic hybrid supports were used in transesterification reactions of vinyl butyrate with 1‐butanol under continuous, supported ionic liquid–liquid conditions with Candida antarctica lipase B (CALB) and octylmethylimidazolium tetrafluoroborate ([OMIM⁺][BF₄^?]) immobilized within the CA beads inside the polymeric monolithic framework and methyl tert‐butyl ether (MTBE) as the continuous phase. The new hybrid bioreactors were successfully used in dimensions up to 2×30 cm (V=94 mL). Under continuous biphasic liquid–liquid conditions a constant conversion up to 96 % was achieved over a period of 18 days, resulting in a productivity of 58 μmol mg^?1(CALB) min^?1. This translates into an unprecedented turnover number (TON) of 3.9×10⁷ within two weeks, which is much higher than the one obtained under standard biphasic conditions using [OMIM⁺][BF₄^?]/MTBE (TON=2.7×10⁶). The continuous liquid–liquid setup based on a hybrid reactor presented here is strongly believed to be applicable to many other enzyme‐catalyzed reactions.     

Hybrid electrospun nonwovens from chitosan/cellulose acetate

Co-mixtures of chitosan (CS) and cellulose acetate (CA) were electrospun into fibrous webs from a binary co-solvent containing 70:30 trifluoroacetic acid (TFA): methylene chloride (DCM). Fibrous webs were produced from CS/CA in ratios (wt%) of 20:80, 40:60, 50:50 and 60:40. As determined by SEM analysis, 12% polymer solutions of CS/CA 60:40 produced structures with uniform bead free fibre morphologies with an average fibre diameter of 458 nm. FTIR-spectroscopy confirmed the presence of CS in the as-spun fibres in the form of chitosan-amine trifluoroacetate salts (NH₃ ⁺CF₃COO⁻). Uniform mixing of the CS and CA components was confirmed by DSC analyses. Alkaline neutralisation of the chitosan amine salts was explored as a means of increasing wet stability. The as-spun fibres were found to be relatively unstable in aqueous medium due to the solubility of the chitosan amine salts. Alkaline post-neutralisation was evaluated as means of minimising weight loss and maximising retention of fibrous structure.     

Bioinspired crystallization of CaCO3 coatings on electrospun cellulose acetate fiber scaffolds and corresponding CaCO3 microtube networks

This article describes the mineralization behavior of CaCO(3) crystals on electrospun cellulose acetate (CA) fibers by using poly(acrylic acid) (PAA) as a crystal growth modifier and further templating synthesis of CaCO(3) microtubes. Calcite film coatings composed of nanoneedles can form on the surfaces of CA fibers while maintaining the fibrous and macroporous structures if the concentration of PAA is in a suitable range. In the presence of a suitable concentration of PAA, the acidic PAA molecules will first adsorb onto the surface of CA fibers by the interaction between the OH moieties of CA and the carboxylic groups of PAA, and then the redundant carboxylic groups of PAA can ionically bind Ca(2+) ions on the surfaces of CA fibers, resulting in the local supersaturation of Ca(2+) ions on and near the fiber surface, which can induce the nucleation of CaCO(3) on the CA fibers instead of in bulk solution. Calcite microtube networks on the macroscale can be prepared by the removal of CA fibers after the CA@CaCO(3) composite is treated with acetone. When the CA fiber scaffold is immersed in CaCl(2) solution with an extended incubation time, the first deposited calcite coatings can act as secondary substrate, leading to the formation of smaller calcite mesocrystal fibers. The present work proves that inorganic crystal growth can occur even at an organic interface without the need for commensurability between the lattices of the organic and inorganic counterparts.     

Antibacterial cellulose acetate films incorporated with N‐halamine‐modified nano‐crystalline cellulose particles

Cellulose acetate (CA) membranes have been widely used as food packaging materials as well as reverse osmosis systems. This study presents the manufacturing of composite CA film with antibacterial properties which is essential for CA film applications in the industry. N‐Halamine precursor of polymethacrylamide‐modified nano‐crystalline cellulose particles (NCC‐PMAMs) were prepared and incorporated into CA film. The composite films with intercalated structure were formed via a solvent‐casting technique. After chlorination, the composite film CA/NCC‐PMAM‐Cl‐1.0 with 1.82 × 10¹⁶ atoms/cm² covalently bonded chlorine showed excellent antibacterial properties by inactivating 6.04 logs of Staphylococcus aureus and 6.27 logs of Escherichia coli within 10 and 5 min, respectively. According to X‐ray diffraction spectra, NCC‐PMAMs behaved as a facilitator for film crystallization. The mechanical strength of the composite film also increased compared with that of pure CA film. However, the composite film became brittle and the maximum decomposition temperature decreased slightly. Preliminary data of in vitro cytocompatibility evaluation indicate that the film is not toxic and has potential use in food packaging. Copyright © 2016 John Wiley & Sons, Ltd.     

Antibacterial and wound healing properties of cellulose acetate electrospun nanofibers loaded with bioactive glass nanoparticles; in-vivo study

Bioactive glasses (BGs) have gained great attention owing to their versatile biological properties. Combining BG nanoparticles (BGNPs) with polymeric nanofibers produced nanocomposites of great performance in various biomedical applications especially in regenerative medicine. In this study, a novel nanocomposite nanofibrous system was developed and optimized from cellulose acetate (CA) electrospun nanofibers containing different concentrations of BGNPs. Morphology, IR and elemental analysis of the prepared electrospun nanofibers were determined using SEM, FT-IR and EDX respectively. Electrical conductivity and viscosity were also studied. Antibacterial properties were then investigated using agar well diffusion method. Moreover, biological wound healing capabilities for the prepared nanofiber dressing were assessed using in-vivo diabetic rat model with induced wounds. The fully characterized CA electrospun uniform nanofiber (100–200 nm) with incorporated BGNPs exhibited broad range of antimicrobial activity against gram negative and positive bacteria. The BGNP loaded CA nanofiber accelerated wound closure efficiently by the 10th day. The remaining wound areas for treated rats were 95.7?±?1.8, 36.4?±?3.2, 6.3?±?1.5 and 0.8?±?0.9 on 1st, 5th, 10th and 15th days respectively. Therefore, the newly prepared BGNP CA nanocomposite nanofiber could be used as a promising antibacterial and wound healing dressing for rapid and efficient recovery.

     

Synthesis and Exploration of Ladder‐Structured Large Aromatic Dianhydrides as Organic Cathodes for Rechargeable Lithium‐Ion Batteries

Compared to anode materials in Li‐ion batteries, the research on cathode materials is far behind, and their capacities are much smaller. Thus, in order to address these issues, we believe that organic conjugated materials could be a solution. In this study, we synthesized two non‐polymeric dianhydrides with large aromatic structures: NDA‐4N (naphthalenetetracarboxylic dianhydride with four nitrogen atoms) and PDA‐4N (perylenetetracarboxylic dianhydride with four nitrogen atoms). Their electrochemical properties have been investigated between 2.0 and 3.9 V (vs. Li⁺/Li). Benefiting from multi‐electron reactions, NDA‐4N and PDA‐4N could reversibly achieve 79.7 % and 92.3 %, respectively, of their theoretical capacity. Further cycling reveals that the organic compound with a relatively larger aromatic building block could achieve a better stability, as an obvious 36.5 % improvement of the capacity retention was obtained when the backbone was switched from naphthalene to perylene. This study proposes an opportunity to attain promising small‐molecule‐based cathode materials through tailoring organic structures.     

A mussel‐inspired method to fabricate a novel reduced graphene oxide/Bi12O17Cl2 composites membrane for catalytic degradation and oil/water separation

In this study, a novel dopamine modified graphene‐based photocatalytic membrane with Bi₁₂O₁₇Cl₂ inserted was fabricated to modify the commercial cellulose acetate membrane via vacuum filtration method. Results showed the reduced graphene oxide (RGO)/poly(dopamine) (PDA)/Bi₁₂O₁₇Cl₂‐CA photocatalytic composite membrane exhibited 98% removal efficiency for methylene blue (MB) within 100 minutes and 96% removal efficiency for 4‐CP within 160 minutes. Importantly, the photocatalytic composite membrane can simultaneously achieve dye degradation and oil‐water separation in only one device within a short time. And the as‐prepared membrane displayed great antifouling performance and recyclability after 10 cycles. Meanwhile, the membrane showed excellent stability in the agitated water bath or different pH conditions. In summary, the photocatalytic membrane investigated in this study opens new avenue for treatment of wastewater.     

Preparation of Antimicrobial Ultrafine Cellulose Acetate Fibers with Silver Nanoparticles

Summary: A feasible method for the preparation of antimicrobial ultrafine fibers with silver nanoparticles was developed by direct electrospinning of a cellulose acetate (CA) solution with small amounts of silver nitrate followed by photoreduction. Silver nanoparticles in ultrafine CA fibers were stabilized by interactions with carbonyl oxygen atoms in CA. Ultrafine CA fibers with silver nanoparticles showed very strong antimicrobial activity.

TEM image of an ultrafine CA fiber electrospun from 10 wt.‐% CA solution with 0.5 wt.‐% AgNO₃.     

Effect of microcrystal cellulose and cellulose whisker on biocompatibility of cellulose-based electrospun scaffolds

To investigate the potential application of microcrystal cellulose (MCC) and cellulose whisker (CW) in the electrospun vascular tissue scaffolds, cellulose acetate (CA) and cellulose composite scaffolds containing MCC and CW were electrospun from CA solutions and deacetylation. Structure and morphology of MCC, CW and the fibrous composite scaffolds were investigated using FT-IR, SEM, TEM and AFM. The wettability of the scaffolds was evaluated by water contact angle analysis. The effect of MCC and CW on the biocompatibility of the scaffolds for vascular smooth muscle cells (VSMC) was assayed by MTT test, fluorescent imaging and SEM. The biocomposite scaffolds displayed multi-scaled structure and morphology. The scaffolds containing MCC and CW simultaneously exhibited significantly higher cell viability compared to those with only MCC or CW and no filler. Cell viability and morphology within the scaffolds become better with increasing content of MCC and CW. The composite scaffolds with both micro- and nano-scale organization could mimic the native extracellular matrix more closely, and further produce synergistic enhancement on VSMC viability, adhesion and proliferation. This study provides the potential applications of renewable cellulose-based particulates in biomedical field.     

Microfibrillated cellulose/cellulose acetate composites: Effect of surface treatment

Microfibrillated cellulose (MFC), which consists of a web‐like array of cellulose fibrils having a diameter in the range of 10–100 nm, was incorporated into a cellulose acetate (CA) matrix to form a totally biobased structural composite. Untreated and a 3‐aminopropyltriethoxysilane (APS) surface treated MFC was combined with a CA matrix by film casting from an acetone suspension. The effectiveness of the surface treatment was determined by infrared spectroscopy and X‐ray photoelectron spectroscopy. The Young's moduli of APS treated MFC composite films increase with increasing MFC content from 1.9 GPa for the CA to 4.1 GPa at 7.5 wt % of MFC, which is more than doubled. The tensile strength of the composite film increases to a maximum of 63.5 MPa at 2.5 wt % compared to the CA which has a value of 38 MPa. The thermal stability of composites with treated MFC is also better than the untreated MFC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 153–161, 2010     

CuSO4/H2O2‐Induced Rapid Deposition of Polydopamine Coatings with High Uniformity and Enhanced Stability

Mussel‐inspired polydopamine (PDA) deposition offers a promising route to fabricate multifunctional coatings for various materials. However, PDA deposition is generally a time‐consuming process, and PDA coatings are unstable in acidic and alkaline media, as well as in polar organic solvents. We report a strategy to realize the rapid deposition of PDA by using CuSO₄/H₂O₂ as a trigger. Compared to the conventional processes, our strategy shows the fastest deposition rate reported to date, and the PDA coatings exhibit high uniformity and enhanced stability. Furthermore, the PDA‐coated porous membranes have excellent hydrophilicity, anti‐oxidant properties, and antibacterial performance. This work demonstrates a useful method for the environmentally friendly, cost‐effective, and time‐saving fabrication of PDA coatings.     

High strength electrospun polymer nanofibers made from BPDA-PDA polyimide

A series of high molecular weight PI precursors, poly(p-phenylene biphenyltetracarboxamide acid), were synthesized from 3,4,3′,4′-biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA) by using intense mechanical stirring at −15 to 0 °C for 48-72 h. The as-synthesized PI precursor solution was used to make BPDA/PDA polyimide thin films and electrospun nanofibers. IR, Ostward Viscometer, CMT-8102 Electromechanical Universal Testing Machine and scanning electron microscope (SEM) were used for the characterizations of the as-synthesized PI precursor, PI films and nanofiber sheets. The high molecular weight BPDA/PDA PI thin films and electrospun nanofiber sheets possess excellent mechanical properties of up to 900 MPa tensile strength with up to 18.0 GPa E-modulus and up to 210 MPa tensile strength with up to 2.5 GPa E-modulus, respectively.     

Bio‐inspired method to fabricate poly‐dopamine/reduced graphene oxide composite membranes for dyes and heavy metal ion removal

Due to the narrow layer spacing, graphene oxide (GO) composite membrane usually exhibits a relatively low water flux in the process of wastewater treatment. In this study, GO was reduced to reduced graphene oxide through a bio‐inspired method, which was functionalized modified by poly‐dopamine (PDA). Then a series of PDA/reduced graphene oxide sheet films were prepared by vacuum filtration on the surface of cellulose acetate membrane (under the pressure of −0.1 MPa). The result indicated that the novel membranes had an excellent stability owing to the cross‐link of PDA. In addition, the hydrophilicity of membrane was increased significantly after PDA modification, which presented a superior water flux than pure GO composite membrane. More importantly, as‐prepared membranes were successfully applied for the removal of dyes (including Congo red, methylene blue, and rhodamine B) and heavy mental ion (Cu(II)) from simulated wastewater. This work might provide a new method for preparation and application of GO composite membranes.     

Cellulose acetate nanocomposite ultrafiltration membranes tailored with hydrous manganese dioxide nanoparticles for water treatment applications

Hydrous manganese dioxide (HMO) nanoparticles incorporated cellulose acetate (CA) composite ultrafiltration (UF) membranes are prepared with the aim of improving the water permeation and BSA contaminant removal. The HMO nanoparticles are synthesized from manganese ion and characterized by FT‐IR, XRD, and FESEM. The effect of variation of HMO on CA membranes is probed using FT‐IR, EDAX, contact angle, SEM, and AFM analysis to demonstrate their chemical functionality, hydrophilicity, and morphology. CA/HMO membranes are showing the enhancement in pure water flux (PWF), water uptake, porosity, hydrophilicity, fouling resistance, BSA rejection, and flux recovery ratio (FRR). CA‐1 membrane displayed higher PWF (143.6 Lm²h^?1), BSA rejection (95.9%), irreversible fouling (93.3%), and FRR (93.3%). Overall results confirmed that the CA/HMO nanocomposite UF membranes overcome the bottlenecks and shows potential for water treatment applications.     

Preparations of regioselectively methylated cellulose acetates and their 1H and 13C NMR spectroscopic analyses

Seven possible regioselectively methylated cellulose acetates (RS‐MCAs)—2,3,6‐tri‐O‐methyl cellulose acetate, 3,6‐di‐O‐methyl cellulose acetate, 2,6‐di‐O‐methyl cellulose acetate, 2,3‐di‐O‐methyl cellulose acetate, 6‐O‐methyl cellulose acetate, 3‐O‐methyl cellulose acetate, and 2‐O‐methyl cellulose acetate—were prepared for the first time from chemically synthesized cellulose derivatives obtained by cationic ring‐opening polymerization and then were analyzed by ¹H and ¹³C NMR spectroscopy. The chemical shifts of ring protons and carbons were influenced by substituent groups (methyl or acetyl) and clearly reflected the pattern of substituent distribution in anhydroglucose units. These data may conveniently be used for the determination of the substituent distribution of methyl cellulose. The synthesized RS‐MCAs also may be used for the elucidation of the structure–property relationship. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4167–4179, 2002     

Synthesis and characterization of novel fluorinated polyimides derived from 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethylphenyl)ethylidene]diphthalic anhydride and aromatic diamines

A novel fluorinated aromatic dianhydride, 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethyl‐phenyl)ethylidene]diphthalic anhydride (TFDA) was synthesized by coupling of 3′‐trifluoromethyl‐2,2,2‐trifluoroacetophenone with o‐xylene under the catalysis of trifluoromethanesulfonic acid, followed by oxidation of KMnO₄ and dehydration. A series of fluorinated aromatic polyimides derived from the novel fluorinated aromatic dianhydride TFDA with various aromatic diamines, such as p‐phenylenediamine (p‐PDA), 4,4′‐oxydianiline (ODA), 1,4‐bis(4‐aminophenoxy)benzene (p‐APB), 1,3‐bis(4‐amino‐phenoxy)benzene (m‐APB), 4‐(4‐aminophenoxy)‐3‐trifluoromethylphenylamine (3FODA) and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (6FAPB), were prepared by polycondensation procedure. All the fluorinated polyimides were soluble in many polar organic solvents such as NMP, DMAc, DMF, and m‐cresol, as well as some of low boiling point organic solvents such as CHCl₃, THF, and acetone. Homogeneous and stable polyimide solutions with solid content as high as 35–40 wt % could be achieved, which were prepared by strong and flexible polyimide films or coatings. The polymer films have good thermal stability with the glass transition temperature of 232–322 °C, the temperature at 5% weight loss of 500–530 °C in nitrogen, and have outstanding mechanical properties with the tensile strengths of 80.5–133.2 MPa as well as elongations at breakage of 7.1–12.6%. It was also found that the polyimide films derived from TFDA and fluorinated aromatic diamines possess low dielectric constants of 2.75–3.02, a low dissipation factor in the range of 1.27–4.50 × 10^?3, and low moisture absorptions <1.3%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4143–4152, 2004