Phase equilibria in the pseudo-binary system SrO-Fe2O3

The phase relations in the pseudo-binary system SrO-Fe₂O₃ have been investigated in air up to 1150°C by means of powder X-ray diffraction and thermal analysis. Sr₃Fe₂O_7−δ, SrFeO_3−δ and SrFe₁₂O₁₉ are stable phases in the entire investigated temperature region, whereas Sr₂FeO_4−δ and Sr₄Fe₃O_10−δ decompose above 930±10°C and 850±25°C, respectively. Sr₄Fe₆O_13±δ is entropy-stabilized relative to SrFeO_3−δ and SrFe₁₂O₁₉ above 775±25°C. Extended solid-solution Sr_1±xFeO_3−δ was demonstrated. On the Fe-deficient side, the extent of solid solubility appeared to decrease gradually with temperature, whereas an abrupt decrease due to formation of Sr₄Fe₆O_13±δ was observed above 775°C on the Sr-deficient side.     

Fabrication of mesoporous SiO2–C–Fe3O4/γ–Fe2O3 and SiO2–C–Fe magnetic composites

A synthetic method for the fabrication of silica-based mesoporous magnetic (Fe or iron oxide spinel) nanocomposites with enhanced adsorption and magnetic capabilities is presented. The successful in situ synthesis of magnetic nanoparticles is a consequence of the incorporation of a small amount of carbon into the pores of the silica, this step being essential for the generation of relatively large iron oxide magnetic nanocrystals (10 ± 3 nm) and for the formation of iron nanoparticles. These composites combine good magnetic properties (superparamagnetic behaviour in the case of SiO₂–C–Fe₃O₄/γ–Fe₂O₃ samples) with a large and accessible porosity made up of wide mesopores (>9 nm). In the present work, we have demonstrated the usefulness of this kind of composite for the adsorption of a globular protein (hemoglobin). The results obtained show that a significant amount of hemoglobin can be immobilized within the pores of these materials (up to 180 mg g⁻¹ for some of the samples). Moreover, we have proved that the composite loaded with hemoglobin can be easily manipulated by means of an external magnetic field.     

Thermal solid–solid interactions and physicochemical properties of NiO/Fe2O3 system doped with K2O

The effects of calcination temperature and doping with K₂O on solid–solid interactions and physicochemical properties of NiO/Fe₂O₃ system were investigated using TG, DTA and XRD techniques. The amounts of potassium, expressed as mol% K₂O were 0.62, 1.23, 2.44 and 4.26. The pure and variously doped mixed solids were thermally treated at 300, 500, 750, 900 and 1000 °C. The catalytic activity was determined for each solid in H₂O₂ decomposition reaction at 30–50 °C. The results obtained showed that the doping process much affected the degree of crystallinity of both NiO and Fe₂O₃ phases detected for all solids calcined at 300 and 500 °C. Fe₂O₃ interacted readily with NiO at temperature starting from 700 °C producing crystalline NiFe₂O₄ phase. The degree of reaction propagation increased with increasing calcination temperature. The completion of this reaction required a prolonged heating at temperature >900 °C. K₂O-doping stimulates the ferrite formation to an extent proportional to its amount added. The stimulation effect of potassium was evidenced by following up the change in the peak height of certain diffraction lines characteristic NiO, Fe₂O₃, NiFe₂O₄ phases located at “d” spacing 2.08, 2.69 and 2.95 Å, respectively. The change of peak height of the diffraction lines at 2.95 Å as a function of firing temperature of pure and doped mixed solids enabled the calculation of the activation energy (ΔE) of the ferrite formation. The computed ΔE values were 120, 80, 49, 36 and 25 kJ mol⁻¹ for pure and variously doped solids, respectively. The decrease in ΔE value of NiFe₂O₄ formation as a function of dopant added was not only attributed to an effective increase in the mobility of reacting cations but also to the formation of potassium ferrite. The calcination temperature and doping with K₂O much affected the catalytic activity of the system under investigation.     

Thermal transformation of quaternary compounds in NaF–CaF2–AlF3 system

Details of quaternary compounds formation in the system NaF–CaF₂–AlF₃ are specified. To achieve this aim, the samples of phases NaCaAlF₆ and Na₂Ca₃Al₂F₁₄ have been obtained by high-temperature solid-phase synthesis. Their thermal behavior when heated up to 800 °C has been studied using the methods of high-temperature X-ray diffraction (XRD) and thermal analysis (TA). The system under consideration can be regarded as a quasibinary section CaF₂–NaAlF₄, where at T=745–750 °C invariant equilibrium is implemented with the phases CaF₂–NaCaAlF₆–Na₂Ca₃Al₂F₁₄–(liquid melt)–(NaAlF₄). The peculiarity of the equilibrium is NaAlF₄ metastability at normal pressure. Below the equilibrium temperature the quaternary phase Na₂Ca₃Al₂F₁₄ is stable and NaCaAlF₆ above this temperature. The phase NaCaAlF₆ fixed by rapid quenching from high temperatures and when heated up to 640 °C decomposes, yielding Na₂Ca₃Al₂F₁₄. Further heating in vacuum at temperature up to 740 °C results in decomposition of Na₂Ca₃Al₂F₁₄ into CaF₂ and Na₃AlF₆. The expected reverse transformation of Na₂Ca₃Al₂F₁₄ into NaCaAlF₆ has not been observed under experimental conditions. Transformations in bulk samples reveal direct and reverse transformation of quaternary phases.

Synopsis

Thermal transformation of the quaternary compounds in system (NaF–CaF₂–AlF₃) was investigated using high-temperature X-ray diffraction (XRD) and thermal analysis (TA). In the system the invariant equilibrium is implemented with the phases CaF₂–NaCaAlF₆–Na₂Ca₃Al₂F₁₄–(liquid melt)–(NaAlF₄) at T=745–750 °C.     

Diagram of phase equilibria in the Fe2V4O13-WO3 system

A diagram for the phase equilibria established in the two-component Fe₂V₄O₁₃-WO₃ system (one of the intersections of the Fe₂O₃-V₂O₅-WO₃ three-component system) has been constructed based on the measurements made by DTA and X-ray phase analysis. The diagram shows that the system investigated does not appear to be a true two-component system, even below the solidus line.     

Subsolidus phase equilibria and properties in the system Bi2O3:Mn2O3±x:Nb2O5

Subsolidus phase relations have been determined for the Bi-Mn-Nb-O system in air (750-900 °C). Phases containing Mn²⁺, Mn³⁺, and Mn⁴⁺ were all observed. Ternary compound formation was limited to pyrochlore (A₂B₂O₆O′), which formed a substantial solid solution region at Bi-deficient stoichiometries (relative to Bi₂(Mn,Nb)₂O₇) suggesting that ≈14-30% of the A-sites are occupied by Mn (likely Mn²⁺). X-ray powder diffraction data confirmed that all Bi-Mn-Nb-O pyrochlores form with structural displacements, as found for the analogous pyrochlores with Mn replaced by Zn, Fe, or Co. A structural refinement of the pyrochlore 0.4000:0.3000:0.3000 Bi₂O₃:Mn₂O_3±x:Nb₂O₅ using neutron powder diffraction data is reported with the A and O′ atoms displaced (0.36 and 0.33 Å, respectively) from ideal positions to 96g sites, and with Mn²⁺ on A-sites and Mn³⁺ on B-sites (Bi_1.6Mn²⁺_0.4(Mn³⁺_0.8Nb_1.2)O₇, (?227), a=10.478(1) Å); evidence of A or O′ vacancies was not found. The displacive disorder is crystallographically analogous to that reported for Bi_1.5Zn_0.92Nb_1.5O_6.92, which has a similar concentration of small B-type ions on the A-sites. EELS spectra for this pyrochlore were consistent with an Mn oxidation between 2+ and 3+. Bi-Mn-Nb-O pyrochlores exhibited overall paramagnetic behavior with negative Curie-Weiss temperature intercepts, slight superparamagnetic effects, and depressed observed moments compared to high-spin, spin-only values. At 300 K and 1 MHz the relative dielectric permittivity of Bi_1.600Mn_1.200Nb_1.200O₇ was ≈128 with tan δ=0.05; however, at lower frequencies the sample was conductive which is consistent with the presence of mixed-valent Mn. Low-temperature dielectric relaxation such as that observed for Bi_1.5Zn_0.92Nb_1.5O_6.92 and other bismuth-based pyrochlores was not observed. Bi-Mn-Nb-O pyrochlores were readily obtained as single crystals and also as textured thin films using pulsed laser deposition.     

Fe2O3/Al2O3氧载体用于甲烷化学链燃烧：负载量与制备方法的影响

以不同方法制备了系列Fe₂O₃/Al₂O₃氧载体,采用XRD、H₂-TPR、CH₄-TPR、O₂-TPD和BET等分析技术对氧载体进行了表征。研究了不同Fe₂O₃负载量氧载体的甲烷化学链燃烧性能,考察了不同制备方法对Fe₂O₃/Al₂O₃氧载体结构、反应性和产物选择性的影响。结果表明,Fe₂O₃负载量对氧载体活性及产物中CO₂选择性的影响较大,负载量较低时氧载体活性较低且引起甲烷部分氧化产物CO含量增加。制备方法亦对氧载体与甲烷的反应活性有所影响,整体上共沉淀法制备的质量分数60％Fe₂O₃/Al₂O₃氧载体具有较高的氧化活性和化学链循环稳定性。其在反应温度850℃、反应时间15 min、30次循环后甲烷转化率及产物中CO₂选择性均未见明显降低。     

The ternary system H2O–Fe(NO3)3–Co(NO3)2 isotherms 0 and 15 °C

The solid–liquid equilibria of the ternary system H₂O–Fe(NO₃)₃–Co(NO₃)₂ were studied by using a synthetic method based on conductivity measurements.

Two isotherms were established at 0 and 15 °C, and the stable solid phases which appear are the iron nitrate nonahydrate (Fe(NO₃)₃·9H₂O), the iron nitrate hexahydrate (Fe(NO₃)₃·6H₂O), the cobalt nitrate hexahydrate (Co(NO₃)₂·6H₂O) and the cobalt nitrate trihydrate (Co(NO₃)₂·3H₂O).     

Characterization and evaluation of Fe2O3/Al2O3 oxygen carrier prepared by sol–gel combustion synthesis

The sol-gel combustion synthesis (SGCS) for oxygen carrier (OC) to be used in chemical looping combustion (CLC) was first designed and experimented in this work, which is a new method of OC synthesis by combining sol-gel technique and solution combustion synthesis. Cheap hydrated metal nitrates and urea were adopted as precursors to prepare Fe₂O₃/Al₂O₃ OC at the molar ratio to unity (Fe1Al1), which was characterized through various means, including Fourier transforms infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffractor (XRD), and N₂ isothermal adsorption/desorption method. FTIR analysis on the chemical structure of the dried gel of Fe1Al1 indicated that urea was partly hydrolyzed and the hydrated basic carbonate was formed by the combination of groups such as (Fe(_1−yAl_y)_1−xO_1−3x, CO₃²⁻ and -OH-. By analyzing the staged products during SGCS, calcination was found as a necessary step to produce Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃. Through TGA-DTA, the decomposition of the dried gel was found to undergo five stages. The analysis of the evolved gases from the gel decomposition using FTIR partially confirmed the staged decomposition and assisted a better understanding of the mechanism of SGCS. XRD identification further substantiated the necessity of calcination to synthesize Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃, though it was not necessary for the synthesis of single phase α-Fe₂O₃ and α-Al₂O₃. Structural characterization performed on N₂ adsorption analyzer displayed that the pore shape of Fe1Al1 particles was heterogeneous. Finally, H₂ temperature-programmed reduction (TPR) of Fe1Al1 products in TGA indicated that the reduction reaction of Fe1Al1 OC after calcination was a single step reaction from α-Fe₂O₃ to Fe, and calcination benefited to improve the transfer rate of the lattice oxygen from the OC to fuel H₂. Furthermore, four times of reduction and oxidization (redox) reaction by alternating with H₂ and air demonstrated the synthesized OC had good reactivity and sintering-resistance, much suitable to be used in the realistic CLC. Overall, the SGCS method was found superior to other existent methods to prepare Fe₂O₃/Al₂O₃ OC for CLC application.     

Preparation of crack-free ZrO2 membrane on Al2O3 support with ZrO2–Al2O3 composite intermediate layers

To develop porous alumina supported MF ZrO₂ membranes, ZrO₂–Al₂O₃ composite intermediate layers are considered in order to decrease stress creation during the processing and avoid cracks formation. The relation between distortion stress and sintering shrinkage was experimentally studied. And the cracks formation mechanism was qualitatively evaluated and discussed. Finally, crack-free YSZ membrane with pore size of 0.16 μm on the two ZrO₂–Al₂O₃ intermediate layers possessing a gradient composition was successfully prepared and characterized.     

The system CePO4–K3PO4

The phase diagram of the system CePO₄–K₃PO₄ has been determined based on investigations by differential thermal analysis, X-ray powder diffraction, IR spectroscopy and optical microscopy. The system contains only one intermediate compound K₃Ce(PO₄)₂, which melts incongruently at (1500±20)°C. This compound is stable down to room temperature and exhibits a polymorphic transition at 1180°C. It was confirmed that the low-temperature form β-K₃Ce(PO₄)₂ crystallizes in a monoclinic system, space group P2₁/m with unit cell parameters a=9.579 (5), b=5.634 (6), c=7.468 (5) Å; =γ=90°, β=90.81 (3)°; V=403.083 Å³.     

Phase relationships in the pseudo-binary 2(ZnTe)-CuInTe2 system

Subsolidus phase relationships in the 2(ZnTe)_x(CuInTe₂)_1−x system were investigated by TEM experiments combined with EDX analysis. The samples were prepared by the solid-state reaction of the elements during long annealing times, followed by either quenching in ice-cold water, or by controlled cooling at different rates. Using the chemical compositions of single and coexisting phases at various temperatures, the boundaries of the two-phase region have been determined. At room temperature, the two-phase region extends from x=0.10 to 0.31. For x<0.10 only mixed crystals with tetragonal structure exist. Between x=0.31 and 1 alloys with the cubic structure are stable.The morphology of the tetragonal domains and their orientation relationship to the cubic matrix were determined by SAD, TEM and HRTEM experiments. The tetragonal phase embedded within the cubic matrix has a flat ellipsoidal shape, whose short axis coincides with the tetragonal c-axis. The three topotaxial orientation relationships between the tetragonal domains and the surrounding cubic matrix were found to be: [001]_tetr.∥[100]_cub., [001]_tetr.∥[010]_cub. and [001]_tetr.∥[001]_cub.. There is an indication that the nucleation starts from small regions displaying cation ordering according to the CuPt-type structure. Reaching the two-phase equilibrium, the tetragonal domains as well as the surrounding cubic phase are free of this cation ordering.     

Thermal behavior of nitrided TiO2/In2O3 by TG–DSC–MS combined with PulseTA

TiO₂/InN (In/(Ti + In) = 6.5:100 mol) was prepared by nitridation of TiO₂/In₂O₃ by NH₃ at 580 °C for 8 h. Only the anatase TiO₂ phase was detected in the XRD measurements. The highly dispersed InN clusters on the surface of anatase TiO₂ nanocrystals were beyond the detection limit of XRD. In order to confirm the existence of InN in the products of nitridation, thermogravimetry–differential scanning calorimetry–mass spectrometry (TG–DSC–MS) coupling techniques were used for a simultaneous characterizing study of the changes of mass, enthalpy and determination of the evolved gases during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃ samples. Moreover, pulse thermal analysis (PulseTA) was combined with TG–DSC–MS for the quantitative calibration of the evolved nitrogen formed during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃. The applied technique enabled identification and quantification of the InN in the products of the nitridation of TiO₂/In₂O_3.     

Polymorphism in the Sc2Si2O7-Y2Si2O7 system

This paper examines the structural changes with temperature and composition in the Sc₂Si₂O₇-Y₂Si₂O₇ system; members of this system are expected to form in the intergranular region of Si₃N₄ and SiC structural ceramics when sintered with the aid of Y₂O₃ and Sc₂O₃ mixtures. A set of different compositions have been synthesized using the sol-gel method to obtain a xerogel, which has been calcined at temperatures between 1300 and 1750 °C during different times. The temperature-composition diagram of the system, obtained from powder XRD data, is dominated by the β-RE₂Si₂O₇ polymorph, with γ-RE₂Si₂O₇ and δ-RE₂Si₂O₇ showing very reduced stability fields. Isotherms at 1300 and 1600 °C have been analysed in detail to evaluate the solid solubility of the components. Although, the XRD data show a complete solid solubility of β-Sc₂Si₂O₇ in β-Y₂Si₂O₇ at 1300 °C, the ²⁹Si MAS-NMR spectra indicate a local structural change at x ca. 1.15 (Sc_2−xY_xSi₂O₇) related to the configuration of the Si tetrahedron, which does not affect the long-range order of the β-RE₂Si₂O₇ structure. Finally, it is interesting to note that, although Sc₂Si₂O₇ shows a unique stable polymorph (β), Sc³⁺ is able to replace Y³⁺ in γ-Y₂Si₂O₇ in the compositional range 1.86?x?2 (where x is Sc_2−xY_xSi₂O₇) as well as in δ-Y₂Si₂O₇ for compositions much closer to the pure Y₂Si₂O₇.     

Liquid–liquid and liquid–liquid–solid equilibrium in Na2CO3–PEG–H2O

The phase diagram was determined for the Na₂CO₃–PEG–H₂O system at 25°C using PEG (poly(ethylene glycol)) with a molecular weight of 4000. Compositions of the liquid–liquid and the liquid–liquid–solid equilibria were determined using calibration curves of density and index of refraction of the solutions, and atomic absorption (AA) and X-ray diffraction analyses were made on the solids. The solid phase in equilibrium with the biphasic region was Na₂CO₃·H₂O. Binodal curves were described using a three-parameter equation. Tie lines were described using the Othmer–Tobias and Bancroft correlation’s. Correlation coefficients for all equations exceeded 0.99. The effects of temperature (25 and 40°C) and the molecular weight of the PEG (2000, 3000, and 4000) on the binodal curve were also studied, and it was observed that the size of the biphasic region increased slightly with an increase in these variables.     

Phase relations in the system K2MoO4–KPO3–MoO3–Bi2O3: A new phosphate K3Bi5(PO4)6

Phase equilibrium in the pseudo-quaternary system K₂O–MoO₃–P₂O₅–Bi₂O₃ was studied as three-component solvent K₂MoO₄–KPO₃–MoO₃ containing 15 mol% Bi₂O₃ during slow cooling and spontaneous crystallization. The results of the investigation were shown on a composition diagram, which indicates the crystallization fields of K₂Bi(PO₄)(MoO₄), K₅Bi(MoO₄)₄, BiPO₄ and K₃Bi₅(PO₄)₆. New phosphate K₃Bi₅(PO₄)₆ was characterized by single-crystal X-ray diffraction (space group C2/c, a=17.680(4), b=6.9370(14), c=18.700(4) Å, β=113.79(3)°) and FTIR spectroscopy. The possibility of lone electron pair stereoactivity of bismuth was suggested using the calculations of characteristics of the Voronoi–Dirichlet polyhedra for K₃Bi₅(PO₄)₆ and K₂Bi(PO₄)(MoO₄).     

Study of the NaBr–DyBr3 phase diagram by differential thermal analysis

The phase diagram of the quasi binary NaBr–DyBr₃ system was determined by differential thermal analysis (DTA) applied to 27 samples covering the complete composition range of the system. The 3NaBr*DyBr₃(s) compound is present in the solid-phase in addition to the pure component halides NaBr(s) and DyBr₃(s). The DyBr₃(s) and 3NaBr*DyBr₃(s) phases showed a polymorphic transition at 1112 and at 733 K, respectively. The {DyBr₃(s) + 3NaBr*DyBr₃(s)} eutectic mixture melts at 709 K giving a liquid of the molar composition x(NaBr) = 0.62. The 3NaBr*DyBr₃(s) phase melts peritectically at 765 K. The phase diagram obtained in the present study virtually agrees with the calculated one available in literature.     

Density and phase diagram of the magnesium–lead system in the region of Mg2Pb intermetallic compound

The phase diagram of magnesium–lead system has been investigated by a new method for phase analysis on the basis of a strong penetrating radiation. The measurements have shown that the standard phase diagram of this system contains inaccuracy in the region of the Mg₂Pb intermetallic compound. New data on the temperature dependences of the solid and the melt densities have been obtained. The density change during the phase transitions has been directly measured.     

Phase diagram features and solidification behaviour of CoCu2O3 at elevated oxygen pressure

A unique behaviour of the phase CoCu₂O₃ was found both from CALPHAD calculations and directional solidification experiments. For elevated oxygen partial pressure the solidification mode changed from double-peritectic to a congruent melting behaviour with respect to the metals (Cu, Co) and to the oxygen content. This transition predicted by the phase diagram calculations was confirmed by microstructure and phase analyses of samples solidified at oxygen pressures up to 60 bar. A DTA analysis has verified basic features of the phase diagram at normal pressures.     

Synthesis and characterization of Fe2O3/SiO2 nanocomposites

Fe₂O₃/SiO₂ nanocomposites based on fumed silica A-300 (S_BET = 337 m²/g) with iron oxide deposits at different content were synthesized using Fe(III) acetylacetonate (Fe(acac)₃) dissolved in isopropyl alcohol or carbon tetrachloride for impregnation of the nanosilica powder at different amounts of Fe(acac)₃ then oxidized in air at 400–900 °C. Samples with Fe(acac)₃ adsorbed onto nanosilica and samples with Fe₂O₃/SiO₂ including 6–17 wt% of Fe₂O₃ were investigated using XRD, XPS, TG/DTA, TPD MS, FTIR, AFM, nitrogen adsorption, Mössbauer spectroscopy, and quantum chemistry methods. The structural characteristics and phase composition of Fe₂O₃ deposits depend on reaction conditions, solvent type, content of grafted iron oxide, and post-reaction treatments. The iron oxide deposits on A-300 (impregnated by the Fe(acac)₃ solution in isopropanol) treated at 500–600 °C include several phases characterized by different nanoparticle size distributions; however, in the case of impregnation of A-300 by the Fe(acac)₃ solution in carbon tetrachloride only α-Fe₂O₃ phase is formed in addition to amorphous Fe₂O₃. The Fe₂O₃/SiO₂ materials remain loose (similar to the A-300 matrix) at the bulk density of 0.12–0.15 g/cm³ and S_BET = 265–310 m²/g.