Asymmetric flow field‐flow fractionation of liposomes: 2. Concentration detection and adsorptive loss phenomena

The applicability of different concentration detection methods for online quantification of liposomes upon asymmetric flow field‐flow fractionation was investigated. Filter‐extruded egg phosphatidylcholine liposomes of different size were used. Online quantification using a differential refractive index (dRI) detector was found feasible for relatively high sample loads in the magnitude of 100 μg lipid (under the chosen fractionation conditions). UV–Vis detection of the turbidity of liposomes was ruled out as online detection method because turbidity increases with particle size and the signal is not only concentration but also particle‐size dependent. Staining of liposomes by Rhodamine phosphatidylethanolamine or Sudan Red and subsequent online UV–Vis detection at the absorption maximum of the dye enabled quantification with much higher sensitivity than dRI detection. Furthermore analyte loss and carry‐over phenomena upon repeated injection of varying liposome sample loads were studied using regenerated cellulose (RC) membranes as accumulation wall. It could be shown that RC membranes are prone to adsorption in case of very small sample loads (0.5 μg). This effect may be overcome by pre‐saturation of the membrane with sample loads of at least 2 μg. For higher sample loads adsorptive losses play a minor role. Recovery from pre‐saturated membranes reached approximately 100% and carry‐over was found negligible.     

Dead volume–free flow splitting in capillary electrophoresis

In recent years, several dual detection concepts (DDCs) for CE were developed, which consisted of at least one nondestructive detector. For these DDCs, a linear detector arrangement could be used, which is not possible when both detectors are destructive. To overcome this problem, we developed a concept for the splitting of the CE stream utilizing commercially available flow splitters (FSs) that allow the parallel positioning of two destructive detectors. In this proof-of-concept study, T- and Y-shaped FSs were characterized regarding their suitability for DDCs. To keep it simple, a UV detector (UV) and a C⁴D were used for the characterization. The model system consisted of an acetonitrile-based background electrolyte and the two model substances, (ferrocenylmethyl)trimethylammonium iodide and caffeine. CE hyphenated to a UV detector (CE-UV) measurements revealed that the split ratio was about 50% for both FSs. CE-C⁴D was used to evaluate the peak shape in front of and behind the FSs. These measurements showed that there was no significant peak broadening introduced by the FSs. Additionally, there were no changes in the LODs in front of and behind the FSs. Furthermore, the flexibility of the new FS approach allowed the usage of capillaries with different ids (25–75 µm) for injection and detection.     

Analysis of lignans in Magnoliae Flos by turbulent flow chromatography with online solid‐phase extraction and high‐performance liquid chromatography with tandem mass spectrometry

In this study, a method coupling turbulent flow chromatography with online solid‐phase extraction and high‐performance liquid chromatography with tandem mass spectrometry was developed for analyzing the lignans in Magnoliae Flos. By the online pretreatment of turbulent flow chromatography solid‐phase extraction, the impurities removal and analytes concentration were automatically processed, and the lignans were separated rapidly and well. Seven lignans of Magnoliae Flos including epieudesmin, magnolin, 1‐irioresinol‐B‐dimethyl ether, epi‐magnolin, fargesin aschantin, and demethoxyaschantin were identified by comparing their retention behavior, UV spectra, and mass spectra with those of reference substances or literature data. The developed method was validated, and the good results showed that the method was not only automatic and rapid, but also accurate and reliable. The turbulent flow chromatography with online solid‐phase extraction and high‐performance liquid chromatography with tandem mass spectrometry method holds a high potential to become an effective method for the quality control of lignans in Magnoliae Flos and a useful tool for the analysis of other complex mixtures.     

Free-flow electrophoresis under microgravity: evidence for enhanced resolution of cell separation

A mixture of fixed rabbit, guinea pig and rat erythrocytes, suspended in a relatively conductive solution, was separated by means of continuous free flow electrophoresis (CFFE) under 1 g- and microgram- conditions using a specially designed electrophoretic module. Short duration microgram conditions were realized on board a sounding rocket. Due to the energy input and the associated thermal convection a separation of the three differently charged cell types in distinct peaks was not possible under 1 g-conditions as shown by reference experiments on the ground before launch. In contrast to the poor resolution under 1 g-conditions, clear separation of the cell mixture could be recorded after lift-off of the rocket under microgram-conditions. Repeated measurements demonstrated that the separation profile was completely stable during the entire microgram-phase of about 6 min. Since the CFFE experiment in space was an exact replica of the ground reference experiments, the results demonstrated unambiguously the potential of CFFE for cell separation under microgram-conditions in media of high ionic strength.     

Two-dimensional liquid chromatography coupled with mass spectrometry for the analysis of Lobelia chinensis Lour. using an ESI/APCI multimode ion source

A comprehensive approach for the separation and identification of components in a traditional Chinese medicine Lobelia chinensis Lour. was developed using 2D-HPLC coupled with an online photodiode array (PDA) detector and a mass spectrometer. The extract of L. chinensis Lour. was separated on a CN column in the first-dimensional HPLC, and then each of the collected fractions was further separated on an ODS column followed by an online PDA detector. After separation in the two different chromatographic modes, the eluents were delivered to a quadrupole mass spectrometer equipped with a multimode ion source of an ESI and an atmospheric pressure chemical ionization (ESI/APCI). At least 536 components in L. chinensis Lour. extract were detected and 6 of them were identified as apigenin 7-O-rutinoside, luteolin, lobetyolinin, lobetyolin, diosmin, and linarin, respectively, according to their UV spectrum and mass spectrum. The results demonstrated the powerful resolution, high peak capacity, as well as the identification capability of the 2D-HPLC combined with PDA and ESI/APCI-MS for the analyses of complex samples.     

Size separation of graphene oxide using preparative free‐flow electrophoresis

Graphene oxide nanosheets often bear a wide size distribution. However, it is critical to have nanosheets with narrow size distribution for their unique size‐dependent physiochemical properties, and nanosheets with a narrow size distribution are the cornerstones for application. Therefore, efficient separation methods of graphene nanosheets have been given considerable attention in many scientific areas recently. Free‐flow electrophoresis is extensively used in the separation and purification of biological molecules with continuous flow separation. The charged graphene oxide nanosheets to some extent are very close in size to biological molecules and share similarity in motion behavior in an electric field. Thus, in the present work, we present a new and simple means to separate graphene oxide nanosheets into more mono‐dispersed size groups by using the free‐flow electrophoresis technique. By optimizing the separation conditions, we were able to obtain graphene oxide sheets with narrow size distribution. The separated samples were characterized by atomic force microscopy, and the size measurements were made by using the software “Image Pro Plus.” In addition, a brief discussion is also given into the theoretic background of the separation of graphene oxide according to the size by the technique of preparative free‐flow electrophoresis.     

Simultaneous Determination of Glyphosate,Glufosinate, and Aminomethylphosphonic Acid by Capillary Electrophoresis After 9‐Fluorenylmethyl Chloroformate Derivatization

A capillary electrophoresis (CE) with UV absorption detection method is described for the simultaneous determination of glufosinate, glyphosate, and aminomethylphosphoric acid. The 9‐fluorenylmethyl chloroformate (FMOC‐Cl) was used for precolumn derivatization of the non‐absorbing herbicides. The three analytes were separated by CE in 9 min with 25 mM borate buffer at pH 9, followed by detection with a UV detector at 260 nm. We demonstrate how the detection limit can be enhanced by using acetonitrile‐salt mixtures. With acetonitrile‐salt mixtures, the limit of detection (LOD) was in the 10^?7 M range. Linearity of more than two orders of magnitude was generally obtained. Precisions of migration times and peak areas were less than 0.9% and 7.5%, respectively. The applicabilities of the method for the analysis of ground water and lake water were examined.     

Separation of amino acids in plant tissue extracts by capillary zone electrophoresis with indirect UV detection using aromatic carboxylates as background electrolytes

Summary Amino acids in extracts of plant tissue were separated and detected by capillary zone electrophoresis (CZE) with indirect UV detection. Various aromatic carboxylates such as salicylate, benzoate, phthalate and trimellitate were investigated as background electrolytes (BGEs). A BGE of benzoate gave the best resolution and detector response. Amino acids were separated at a highly alkaline pH to charge amino acids negatively. Separation was achieved by the co-electroosmotic flow (Co-EOF) by the addition of the cationic surfactant myristyltrimethyl-ammonium bromide (MTAB) to the electrolyte. The condtions affecting the separation of amino acids, including electrolyte pH, concentrations of both benzoate and MTAB, were investigated and optimised. Separation of a mixture of 17 amino acids at pH 11.20 with indirect UV detection at 225 nm was achieved with a BGE of 10 mM benzoate containing 1.0 mM MTAB at pH of 11.20. Detection limits ranged between 10 and 50 μM. The proposed method was demonstrated by the determination of amino acids in extracts of Eucalypt leaves with direct injection of samples.     

Evaluation of band broadening in chemiluminescence detection coupled to pressurized capillary electrochromatography with an off-column coaxial flow interface

A system of off-column coaxial flow chemiluminescence (CL) detection coupled to pressurized CEC (pCEC) was described. The interface utilized a reactor that introduced postcolumn CL reagent into the capillary effluents in a sheathing flow profile. To compare and evaluate band broadening of analytes caused by the detector, the typical CL compounds luminol and N-(4-aminobutyl)-N-ethylisoluminol (ABEI) were separated and detected by pCEC or capillary HPLC (cHPLC) coupled to CL and UV detector, respectively. The results demonstrated that the band broadening caused by off-column detection interface was minimized due to the fast kinetic nature of the CL reaction. With the proposed pCEC-CL system, the detection limits of luminol and ABEI were 1.0x10(-8) and 8.0x10(-8) mol/L, respectively, which were approximately 100-fold more sensitive than those obtained with UV absorption. In addition, separation and detection of the ABEI-labeled L-lysine (L-Lys) and L-arginine (L-Arg) were accomplished by pCEC-CL method based on the principle of ABEI-potassium ferricyanide-alkaline medium CL reaction system. Under the optimum conditions, good results could be achieved compared with pCEC-UV.     

A theoretical study of the possible use of electroosmotic flow to extend the read length of DNA sequencing by end-labeled free solution electrophoresis

End-labeled free solution electrophoresis (ELFSE) provides a means of separating DNA with free-solution CE, eliminating the need for gels and polymer solutions which increase the run time and can be difficult to load into a capillary. In free-solution electrophoresis, DNA is normally free-draining and all fragments reach the detector at the same time, whereas ELFSE uses an uncharged label molecule attached to each DNA fragment in order to render the electrophoretic mobility size-dependent. With ELFSE, however, the larger molecules are not separated enough (limiting the read length in the case of ssDNA sequencing) while the smaller ones are overseparated; the larger ones are too fast while the shorter ones are too slow, which is the opposite of traditional gel-based methods. In this article, we show how an EOF could be used to overcome these problems and extend the DNA sequencing read length of ELFSE. This counterflow would allow the larger, previously unresolved molecules more time to separate and thereby increase the read length. Through our theoretical investigation, we predict that an EOF mobility of approximately the same magnitude as that of unlabeled DNA would provide the best results for the regime where all molecules move in the same direction. Even better resolution would be possible for smaller values of EOF which allow different directions of migration; however, the migration times then would become too large. The flow would need to be well controlled since the gain in read length decreases as the magnitude of the counterflow increases; an EOF mobility double that of unlabeled DNA would no longer increase the read length, although ELFSE would still benefit from a reduction in migration time.     

毛细管电泳泡状检测池的制备及性能考察

采用局部成泡法自行制备毛细管电泳仪用泡状检测池。与普通圆柱形检测池相比,采用泡状池,检测信号可以提高６倍。对照讨论了泡状对电泳过程的影响。     

Enhancing resolution of free‐flow zone electrophoresis via a simple sheath‐flow sample injection

In this work, a simple and novel sheath‐flow sample injection method (SFSIM) is introduced to reduce the band broadening of free‐flow zone electrophoresis separation in newly developed self‐balance free‐flow electrophoresis instrument. A needle injector was placed in the center of the separation inlet, into which the BGE and sample solution were pumped simultaneously. BGE formed sheath flow outside the sample stream, resulting in less band broadening related to hydrodynamics and electrodynamics. Hemoglobin and C‐phycocyanin were successfully separated by the proposed method in contrast to the poor separation of free‐flow electrophoresis with the traditional injection method without sheath flow. About 3.75 times resolution enhancement could be achieved by sheath‐flow sample injection method.     

Electrochemically assisted injection – a new approach for hyphenation of electrochemistry with capillary-based separation systems

A new concept based on the electrochemical conversion of analyte species during the injection into capillary flow systems is presented. This approach is termed electrochemically assisted injection (EAI). In a specially designed injection cell containing the analyte solution a conversion efficiency of about 83% can be achieved. Potassium octacyanotungstate(IV) served as a model compound for the analytical characterisation of EAI applying capillary flow injection analysis with double-pulse amperometric detection. Capillary electrophoresis experiments were performed using EAI to study the electrochemical oxidation of various ferrocene derivatives in acetonitrile solution. The electropherograms recorded with UV detection show separated signals for the ferrocene compounds and their oxidation products. The migration behaviour and the stability of ferrocenium cations and other reaction products were investigated.     

Capillary electrophoretic system incorporating an UV/CL dual detector

We developed a capillary electrophoretic system incorporating an ultra-violet absorption (UV)/chemiluminescence (CL) dual detector, taking advantage of the CL reaction of luminol-hydrogen peroxide and the batch-type CL detection cell. UV detection was carried out using the on-capillary method while CL detection was performed using the end-capillary method. Examination of isoluminol isothiocyanate (ILITC) as a model sample revealed two main peaks with UV detection and one main peak with CL detection. The first peak in the UV detection data corresponded to the main peak in the CL detection data. We then determined that the ILITC sample included natural ILITC as well as an impurity that had absorption behavior but did not have CL properties and labeling ability. Furthermore, the components of a mixture containing glycine, glycylglycine and glycylglycylglycine, all labeled with ILITC, were well separated and detected using the present system. The present system easily, rapidly, and simultaneously produces useful information due to the presence of both UV and CL detectors.     

高效毛细管电泳紫外检测器光路的特殊性及其优化

紫外检测器用于高效毛细管电泳（ＨＰＣＥ）的主要难题在光路中,ＨＰＣＥ中熔融石英毛细管（内径通常在５０μｍ左右）直接放在光路中,一方面光程短,另一方面,光在透镜及毛细管界面上的折射与反射使光程常比毛细管内径短,甚至可能绕过毛细管内腔［１,２］．本文编制...     

Micellar electrokinetic chromatography with on-line Fourier transform infrared detection

Micellar electrokinetic chromatography (MEKC) was successfully coupled to Fourier transform infrared (FTIR) detection, using a micromachined IR-transparent flow cell with an optical path length of 15 micro m for the on-line detection of five neutral analytes. Tight connections between the flow cell and the capillaries were achieved by creating a small O-ring of UV-curing epoxy adhesive on the sharply cut capillary ends. The background electrolyte consisted of 15 mM phosphate buffer at pH 7 and 40 mM sodium dodecyl sulfate (SDS). Five analytes (paracetamol, caffeine, p-nitro benzyl alcohol, m-nitrophenol and p-nitrophenol) were successfully separated, yielding detailed IR stack plots that could be used for quantification and identification. Linear calibration graphs were obtained for each individual analyte present in mixtures at concentrations up to 10 mM. The limit of detection (3 S/N) ranged between 1.1 and 1.5 mM (1.2-1.8 ng). Analytes were identified by comparing spectra obtained during the MEKC separation with those resulting from completely filling the capillary with each individual analyte dissolved in the micelle-containing electrolyte. Information on the specific functional groups of all analytes could be elucidated from the spectra. Since FTIR is a nondestructive detection technique, a conventional on-line UV detector was introduced directly after the developed IR flow cell to test the system's performance and to demonstrate that tandem FTIR and UV detection is feasible.     

Detectability enhancement of spectrophotometric detectors by the use of multidimensional gas chromatography

Multidimensional gas chromatography (2D GC) is demonstrated as a way to improve limits of detectability of spectrophotometric detectors. UV and IR detectors are generally less sensitive than mass spectrometers or other GC detectors. This has placed some limitations on the useful capabilities provided by spectrophotometric detectors, such as the ability to provide structure‐related information for a particular analyte. In this paper, we report results from interfacing a 2D GC instrument to a UV detector. Symmetry factor and the ratio of retention time divided by peak width did not show deterioration of the quality of chromatography when a megabore column was used with this detector. Furthermore, an increase in the limits of detectability over that attainable in a single‐column system was realized by using the 2D GC system. However, the low flow (1 mL/min) imposed by the use of a microbore column (250 μm ID) caused significant tailing when the UV detector was used.     

Simultaneous determination of atenolol and amiloride in pharmaceutical preparations by capillary zone electrophoresis with capacitively coupled contactless conductivity detection

Capillary zone electrophoresis coupled with a capacitively coupled contactless conductivity detector (CE‐C⁴D) has been employed for the determination of atenolol and amiloride in pharmaceutical formulations. Acetic acid (150 mm ) was used as background electrolyte. The influence of several factors (detector excitation voltage and frequency, buffer concentration, applied voltage, capillary temperature and injection time) was studied. Non‐UV‐absorbing L‐valine was used as internal standard; the analytes were all separated in less than 7 min. The separation was carried out in normal polarity mode at 28°C, 25 kV and using hydrodynamic injection (25 s). The separation was effected in an uncoated fused‐silica capillary (75 μm, i.d. × 52 cm). The CE‐C⁴D method was validated with respect to linearity, limit of detection and quantification, accuracy, precision and selectivity. Calibration curves were linear over the range 5–250 μg/mL for the studied analytes. The relative standard deviations of intra‐ and inter‐day migration times and corrected peak areas were less than 6.0%. The method showed good precision and accuracy and was successfully applied to the simultaneous determination of atenolol and amiloride in different pharmaceutical tablet formulations. Copyright © 2010 John Wiley & Sons, Ltd.     

Ionene-dynamically coated capillary for analysis of urinary and recombinant human erythropoietin by capillary electrophoresis and online electrospray ionization mass spectrometry

In this article, a series of ionene polymers were synthesized and used to coat fused-silica capillaries for the separation of recombinant and urinary human erythropoietin (rhEPO and uEPO) standards by CE. The influence of the charge density of coatings on the separation of rhEPO and uEPO glycoforms was investigated. Then, we further studied the method for fast separation and detection of rhEPO and uEPO standards by CE-ESI-MS. The influence of several CE and MS operating parameters, such as the concentration of CE running buffer, applied external pressure, and the composition and flow rate of sheath liquid on CE-ESI-MS was studied. The results demonstrated that when the capillary was permanently coated with 6,6-ionene and the pH value of acetic acid-ammonium acetate running buffer was 4.80 and 5.50, respectively, a significantly reproducible separation was achieved for rhEPO and uEPO glycoforms. In the online CE-ESI-MS experiments, we not only achieved the online MS signal of uEPO, but also obtained baseline separation of three major rhEPO glycoforms successfully and reproducibly on the 6,6-ionene-coated capillaries. Furthermore, the standard mixture of rhEPO and uEPO was separated, and two incompletely resolved peaks that were identified to be rhEPO and uEPO by the unique MS "fingerprint" were obtained. Additionally, the molecular weight of rhEPO and uEPO were verified and compared to the results by MALDI-TOF-MS. It can be concluded that, in contrast to other indirect methods, the online CE-ESI-MS technique with the combination of the advantages of both CE and MS shows great potential for the separation and detection of rhEPO doping directly in competitive sports.     

Mid-scale free-flow electrophoresis with gravity-induced uniform flow of background buffer in chamber for the separation of cells and proteins

A large-scale free-flow electrophoresis (LS-FFE) is often too large for cell separation of lab scale, whereas micro-FFE (μFFE) has great difficulty in cell isolation due to easy blockage by cell accumulation in μFFE. In this study, a mid-scale FFE (MS-FFE) is developed for cell and protein separations. The volume of the separation chamber (70×40×0.1-0.8 mm) is from 280 μL to 2.24 mL, much lower than that in an LS-FFE but higher than that in a μFFE. Gravity is used for uniform flow of the background buffer only via a single pump with 16 channels and the sample is injected via an adjuster originally used for clinical intravenous injection. The experiments reveal that the hydrodynamic and electrohydrodynamic flows are much stable, and the Joule heat can be effectively dispersed without obvious positive or negative deviation as shown by the omega plots. By the device, Escherichia coli and Staphylococcus aureus, which easily accumulate to block μFFE and are separated with difficulty due to their same negative charges carried, can be well isolated under the conditions of 4.5 mM pH 8.5 Tris-boric buffer (4.5 mM Tris, 4.5 mM boric acid) with 0.10 mM ethylene diamine tetraacetic acid and 5% m/v sucrose, 200 μL/min, 800 V, and sample injection via inlet 4. The mid-scale FFE device could also be used for the separation of three model proteins of horse heart cytochrome c, myoglobin and bovine serum albumin. The device has clear significance for mid-scale separation of cells and proteins.